1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
|
# Main state, i.e. what user wants. Controlled by RC or from ground station via telemetry link.
uint8 MAIN_STATE_MANUAL = 0
uint8 MAIN_STATE_ALTCTL = 1
uint8 MAIN_STATE_POSCTL = 2
uint8 MAIN_STATE_AUTO_MISSION = 3
uint8 MAIN_STATE_AUTO_LOITER = 4
uint8 MAIN_STATE_AUTO_RTL = 5
uint8 MAIN_STATE_ACRO = 6
uint8 MAIN_STATE_OFFBOARD = 7
uint8 MAIN_STATE_MAX = 8
# If you change the order, add or remove arming_state_t states make sure to update the arrays
# in state_machine_helper.cpp as well.
uint8 ARMING_STATE_INIT = 0
uint8 ARMING_STATE_STANDBY = 1
uint8 ARMING_STATE_ARMED = 2
uint8 ARMING_STATE_ARMED_ERROR = 3
uint8 ARMING_STATE_STANDBY_ERROR = 4
uint8 ARMING_STATE_REBOOT = 5
uint8 ARMING_STATE_IN_AIR_RESTORE = 6
uint8 ARMING_STATE_MAX = 7
uint8 HIL_STATE_OFF = 0
uint8 HIL_STATE_ON = 1
# Navigation state, i.e. "what should vehicle do".
uint8 NAVIGATION_STATE_MANUAL = 0 # Manual mode
uint8 NAVIGATION_STATE_ALTCTL = 1 # Altitude control mode
uint8 NAVIGATION_STATE_POSCTL = 2 # Position control mode
uint8 NAVIGATION_STATE_AUTO_MISSION = 3 # Auto mission mode
uint8 NAVIGATION_STATE_AUTO_LOITER = 4 # Auto loiter mode
uint8 NAVIGATION_STATE_AUTO_RTL = 5 # Auto return to launch mode
uint8 NAVIGATION_STATE_AUTO_RCRECOVER = 6 # RC recover mode
uint8 NAVIGATION_STATE_AUTO_RTGS = 7 # Auto return to groundstation on data link loss
uint8 NAVIGATION_STATE_AUTO_LANDENGFAIL = 8 # Auto land on engine failure
uint8 NAVIGATION_STATE_AUTO_LANDGPSFAIL = 9 # Auto land on gps failure (e.g. open loop loiter down)
uint8 NAVIGATION_STATE_ACRO = 10 # Acro mode
uint8 NAVIGATION_STATE_LAND = 11 # Land mode
uint8 NAVIGATION_STATE_DESCEND = 12 # Descend mode (no position control)
uint8 NAVIGATION_STATE_TERMINATION = 13 # Termination mode
uint8 NAVIGATION_STATE_OFFBOARD = 14
uint8 NAVIGATION_STATE_MAX = 15
# VEHICLE_MODE_FLAG, same as MAV_MODE_FLAG of MAVLink 1.0 protocol
uint8 VEHICLE_MODE_FLAG_SAFETY_ARMED = 128
uint8 VEHICLE_MODE_FLAG_MANUAL_INPUT_ENABLED = 64
uint8 VEHICLE_MODE_FLAG_HIL_ENABLED = 32
uint8 VEHICLE_MODE_FLAG_STABILIZED_ENABLED = 16
uint8 VEHICLE_MODE_FLAG_GUIDED_ENABLED = 8
uint8 VEHICLE_MODE_FLAG_AUTO_ENABLED = 4
uint8 VEHICLE_MODE_FLAG_TEST_ENABLED = 2
uint8 VEHICLE_MODE_FLAG_CUSTOM_MODE_ENABLED = 1
# VEHICLE_TYPE, should match 1:1 MAVLink's MAV_TYPE ENUM
uint8 VEHICLE_TYPE_GENERIC = 0 # Generic micro air vehicle.
uint8 VEHICLE_TYPE_FIXED_WING = 1 # Fixed wing aircraft.
uint8 VEHICLE_TYPE_QUADROTOR = 2 # Quadrotor
uint8 VEHICLE_TYPE_COAXIAL = 3 # Coaxial helicopter
uint8 VEHICLE_TYPE_HELICOPTER = 4 # Normal helicopter with tail rotor.
uint8 VEHICLE_TYPE_ANTENNA_TRACKER = 5 # Ground installation
uint8 VEHICLE_TYPE_GCS = 6 # Operator control unit / ground control station
uint8 VEHICLE_TYPE_AIRSHIP = 7 # Airship, controlled
uint8 VEHICLE_TYPE_FREE_BALLOON = 8 # Free balloon, uncontrolled
uint8 VEHICLE_TYPE_ROCKET = 9 # Rocket
uint8 VEHICLE_TYPE_GROUND_ROVER = 10 # Ground rover
uint8 VEHICLE_TYPE_SURFACE_BOAT = 11 # Surface vessel, boat, ship
uint8 VEHICLE_TYPE_SUBMARINE = 12 # Submarine
uint8 VEHICLE_TYPE_HEXAROTOR = 13 # Hexarotor
uint8 VEHICLE_TYPE_OCTOROTOR = 14 # Octorotor
uint8 VEHICLE_TYPE_TRICOPTER = 15 # Octorotor
uint8 VEHICLE_TYPE_FLAPPING_WING = 16 # Flapping wing
uint8 VEHICLE_TYPE_KITE = 17 # Kite
uint8 VEHICLE_TYPE_ONBOARD_CONTROLLER=18 # Onboard companion controller
uint8 VEHICLE_TYPE_VTOL_DUOROTOR = 19 # Vtol with two engines
uint8 VEHICLE_TYPE_VTOL_QUADROTOR = 20 # Vtol with four engines*/
uint8 VEHICLE_TYPE_ENUM_END = 21
uint8 VEHICLE_BATTERY_WARNING_NONE = 0 # no battery low voltage warning active
uint8 VEHICLE_BATTERY_WARNING_LOW = 1 # warning of low voltage
uint8 VEHICLE_BATTERY_WARNING_CRITICAL = 2 # alerting of critical voltage
# state machine / state of vehicle.
# Encodes the complete system state and is set by the commander app.
uint16 counter # incremented by the writing thread everytime new data is stored
uint64 timestamp # in microseconds since system start, is set whenever the writing thread stores new data
uint8 main_state # main state machine
uint8 nav_state # set navigation state machine to specified value
uint8 arming_state # current arming state
uint8 hil_state # current hil state
bool failsafe # true if system is in failsafe state
int32 system_type # system type, inspired by MAVLink's VEHICLE_TYPE enum
int32 system_id # system id, inspired by MAVLink's system ID field
int32 component_id # subsystem / component id, inspired by MAVLink's component ID field
bool is_rotary_wing # True if system is in rotary wing configuration, so for a VTOL this is only true while flying as a multicopter
bool is_vtol # True if the system is VTOL capable
bool vtol_fw_permanent_stab # True if vtol should stabilize attitude for fw in manual mode
bool condition_battery_voltage_valid
bool condition_system_in_air_restore # true if we can restore in mid air
bool condition_system_sensors_initialized
bool condition_system_returned_to_home
bool condition_auto_mission_available
bool condition_global_position_valid # set to true by the commander app if the quality of the position estimate is good enough to use it for navigation
bool condition_launch_position_valid # indicates a valid launch position
bool condition_home_position_valid # indicates a valid home position (a valid home position is not always a valid launch)
bool condition_local_position_valid
bool condition_local_altitude_valid
bool condition_airspeed_valid # set to true by the commander app if there is a valid airspeed measurement available
bool condition_landed # true if vehicle is landed, always true if disarmed
bool condition_power_input_valid # set if input power is valid
float32 avionics_power_rail_voltage # voltage of the avionics power rail
bool usb_connected # status of the USB power supply
bool rc_signal_found_once
bool rc_signal_lost # true if RC reception lost
uint64 rc_signal_lost_timestamp # Time at which the RC reception was lost
bool rc_signal_lost_cmd # true if RC lost mode is commanded
bool rc_input_blocked # set if RC input should be ignored
bool data_link_lost # datalink to GCS lost
bool data_link_lost_cmd # datalink to GCS lost mode commanded
uint8 data_link_lost_counter # counts unique data link lost events
bool engine_failure # Set to true if an engine failure is detected
bool engine_failure_cmd # Set to true if an engine failure mode is commanded
bool gps_failure # Set to true if a gps failure is detected
bool gps_failure_cmd # Set to true if a gps failure mode is commanded
bool barometer_failure # Set to true if a barometer failure is detected
bool offboard_control_signal_found_once
bool offboard_control_signal_lost
bool offboard_control_signal_weak
uint64 offboard_control_signal_lost_interval # interval in microseconds without an offboard control message
bool offboard_control_set_by_command # true if the offboard mode was set by a mavlink command and should not be overridden by RC
# see SYS_STATUS mavlink message for the following
uint32 onboard_control_sensors_present
uint32 onboard_control_sensors_enabled
uint32 onboard_control_sensors_health
float32 load # processor load from 0 to 1
float32 battery_voltage
float32 battery_current
float32 battery_remaining
uint8 battery_warning # current battery warning mode, as defined by VEHICLE_BATTERY_WARNING enum
uint16 drop_rate_comm
uint16 errors_comm
uint16 errors_count1
uint16 errors_count2
uint16 errors_count3
uint16 errors_count4
bool circuit_breaker_engaged_power_check
bool circuit_breaker_engaged_airspd_check
bool circuit_breaker_engaged_enginefailure_check
bool circuit_breaker_engaged_gpsfailure_check
|
