1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
|
/************************************************************************************
* configs/arduino-due/include/board.h
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H
#define __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
# include <stdbool.h>
# ifdef CONFIG_SAM34_GPIO_IRQ
# include <arch/irq.h>
# endif
#endif
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* After power-on reset, the SAM3X device is running on a 4MHz internal RC. These
* definitions will configure clocking
*
* MAINOSC: Frequency = 12MHz (crysta)
* PLLA: PLL Divider = 1, Multiplier = 14 to generate PLLACK = 168MHz
* Master Clock (MCK): Source = PLLACK, Prescalar = 1 to generate MCK = 84MHz
* CPU clock: 84MHz
*/
#define BOARD_32KOSC_FREQUENCY (32768)
#define BOARD_SCLK_FREQUENCY (BOARD_32KOSC_FREQUENCY)
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
/* Main oscillator register settings.
*
* The start up time should be should be:
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
*/
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
/* PLLA configuration.
*
* Divider = 1
* Multipler = 14
*/
#define BOARD_CKGR_PLLAR_MUL (13 << PMC_CKGR_PLLAR_MUL_SHIFT)
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
/* PMC master clock register settings.
*
* Source = PLLA
* Divider = 2
*/
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV2
/* USB UTMI PLL start-up time */
#define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT)
/* Resulting frequencies */
#define BOARD_PLLA_FREQUENCY (168000000) /* PLLACK: 14 * 12Mhz / 1 */
#define BOARD_MCK_FREQUENCY (84000000) /* MCK: PLLACK / 2 */
#define BOARD_CPU_FREQUENCY (84000000) /* CPU: MCK */
/* HSMCI clocking
*
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
* divided by (2*(CLKDIV+1)).
*
* MCI_SPEED = MCCK / (2*(CLKDIV+1))
* CLKDIV = MCCK / MCI_SPEED / 2 - 1
*
* Where CLKDIV has a range of 0-255.
*/
/* MCK = 84MHz, CLKDIV = 104, MCI_SPEED = 84MHz / 2 * (104+1) = 400 KHz */
#define HSMCI_INIT_CLKDIV (104 << HSMCI_MR_CLKDIV_SHIFT)
/* MCK = 84MHz, CLKDIV = 2, MCI_SPEED = 84MHz / 2 * (2+1) = 14 MHz */
#define HSMCI_MMCXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
/* MCK = 84MHz, CLKDIV = 1, MCI_SPEED = 84MHz / 2 * (1+1) = 21 MHz */
#define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
/* FLASH wait states
*
* FWS MAX FREQUENCY
* 1.62V 1.8V
* --- ----- ------
* 0 17MHz 19MHz
* 1 45MHz 50MHz
* 2 58MHz 64MHz
* 3 70MHz 80MHz
* 4 78MHz 90MHz
*/
#define BOARD_FWS 4
/* LED definitions ******************************************************************/
/* There are three user-controllable LEDs on board the Arduino Due board:
*
* LED GPIO
* ---------------- -----
* L Amber LED PB27
* TX Yellow LED PA21
* RX Yellow LED PC30
*
* LED L is connected to ground and can be illuminated by driving the PB27
* output high. The TX and RX LEDs are pulled high and can be illuminated by
* driving the corresponding
* GPIO output to low.
*/
/* LED index values for use with sam_setled() */
#define BOARD_LED_L 0
#define BOARD_LED_RX 1
#define BOARD_LED_TX 2
#define BOARD_NLEDS 3
/* LED bits for use with sam_setleds() */
#define BOARD_LED_L_BIT (1 << BOARD_LED_L)
#define BOARD_LED_RX_BIT (1 << BOARD_LED_RX)
#define BOARD_LED_TX_BIT (1 << BOARD_LED_TX)
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
* SYMBOL MEANING LED STATE
* L TX RX
* ----------------------- -------------------------- -------- -------- -------- */
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF OFF */
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF OFF */
#define LED_STACKCREATED 1 /* Idle stack created ON OFF OFF */
#define LED_INIRQ 2 /* In an interrupt N/C GLOW OFF */
#define LED_SIGNAL 2 /* In a signal handler N/C GLOW OFF */
#define LED_ASSERTION 2 /* An assertion failed N/C GLOW OFF */
#define LED_PANIC 3 /* The system has crashed N/C N/C Blinking */
#define LED_PANIC 3 /* MCU is is sleep mode ------ Not used -------- */
/* Thus if LED L is statically on, NuttX has successfully booted and is,
* apparently, running normmally. If LED RX is glowing, then NuttX is
* handling interupts (and also signals and assertions). If TX is flashing
* at approximately 2Hz, then a fatal error has been detected and the system
*/
/* Button definitions ***************************************************************/
/* There are no buttons on the Arduino Due board. */
/* GPIO pin configurations **********************************************************/
#if 1 /* #ifdef CONFIG_ADRUINO_DUE_REV3 works with REV2 as well */
/* This port was performed on the Arduino Due Rev 2 board. A NuttX user reported
* issues with the serial port on his Aduino Due Rev 3 board. That problem was
* resolved as follows:
*
* "... The issue was in my hardware. I found the difference between Arduino
* Due shematics (revision R2) and actual PCB layout of my Arduino (revision
* R3). On a schematics which I download from arduino.cc was shown that 2nd
* pin of IC10 is connected to the ground, but on my Arduino the 2nd pin
* of IC10 was connected to its 1st pin instead of ground and in my case
* IC10 works in open-drain mode, but RX0 pin on SAM3x doesn't have pull-up
* and thus TX signal from AtMega16U2 can't reach the SAM3x input pin, on
* this pin always '0'.
*
* "My solution is to enable internal pull-up in SAM3x. ...
* Now shell console on UART0 (via USB programming connector) of Arduino Due
* Due works as expected."
*/
# undef GPIO_UART0_RXD
# define GPIO_UART0_RXD (GPIO_PERIPHA | GPIO_CFG_DEFAULT | GPIO_PORT_PIOA | \
GPIO_PIN8 | GPIO_CFG_PULLUP)
#endif
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: sam_boardinitialize
*
* Description:
* All SAM3X architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
void sam_boardinitialize(void);
/************************************************************************************
* Name: sam_ledinit, sam_setled, and sam_setleds
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If
* CONFIG_ARCH_LEDS is not defined, then the following interfacesare available to
* control the LEDs from user applications.
*
************************************************************************************/
#ifndef CONFIG_ARCH_LEDS
void sam_ledinit(void);
void sam_setled(int led, bool ledon);
void sam_setleds(uint8_t ledset);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_ARDUINO_DUE_INCLUDE_BOARD_H */
|
