From 45369a3188583ebaef68da5b379121fc582b3287 Mon Sep 17 00:00:00 2001 From: Gregory Nutt Date: Fri, 28 Mar 2014 15:18:49 -0600 Subject: configs/sama5d3x-ek: Fix some typos --- nuttx/configs/sama5d3x-ek/README.txt | 16 ++++++++-------- nuttx/configs/sama5d3x-ek/include/board.h | 4 ++-- nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h | 2 +- 3 files changed, 11 insertions(+), 11 deletions(-) diff --git a/nuttx/configs/sama5d3x-ek/README.txt b/nuttx/configs/sama5d3x-ek/README.txt index ace70ddb6..ec7d89b5c 100644 --- a/nuttx/configs/sama5d3x-ek/README.txt +++ b/nuttx/configs/sama5d3x-ek/README.txt @@ -460,7 +460,7 @@ Buttons and LEDs Only the momentary push button is controllable by software (labeled "PB_USER1" on the board): - - PE27. Pressing the switch connect PE27 to grounded. Therefore, PE27 + - PE27. Pressing the switch connects PE27 to grounded. Therefore, PE27 must be pulled high internally. When the button is pressed the SAMA5 will sense "0" is on PE27. @@ -566,11 +566,11 @@ Networking System Type -> EMAC device driver options CONFIG_SAMA5_EMAC_NRXBUFFERS=16 : Set aside some RS and TX buffers CONFIG_SAMA5_EMAC_NTXBUFFERS=4 - CONFIG_SAMA5_EMAC_PHYADDR=1 : KSZ8051 PHY is at address 1 + CONFIG_SAMA5_EMAC_PHYADDR=1 : KSZ8021/31 PHY is at address 1 CONFIG_SAMA5_EMAC_AUTONEG=y : Use autonegotiation CONFIG_SAMA5_EMAC_RMII=y : Either MII or RMII interface should work - CONFIG_SAMA5_EMAC_PHYSR=30 : Address of PHY status register on KSZ8051 - CONFIG_SAMA5_EMAC_PHYSR_ALTCONFIG=y : Needed for KSZ8051 + CONFIG_SAMA5_EMAC_PHYSR=30 : Address of PHY status register on KSZ8021/31 + CONFIG_SAMA5_EMAC_PHYSR_ALTCONFIG=y : Needed for KSZ8021/31 CONFIG_SAMA5_EMAC_PHYSR_ALTMODE=0x7 : " " " " " " CONFIG_SAMA5_EMAC_PHYSR_10HD=0x1 : " " " " " " CONFIG_SAMA5_EMAC_PHYSR_100HD=0x2 : " " " " " " @@ -578,7 +578,7 @@ Networking CONFIG_SAMA5_EMAC_PHYSR_100FD=0x6 : " " " " " " PHY selection. Later in the configuration steps, you will need to select - the KSZ8051 PHY for EMAC (See below) + the KSZ8021/31 PHY for EMAC (See below) Selecting the GMAC peripheral ----------------------------- @@ -622,7 +622,7 @@ Networking Device drivers -> Network Device/PHY Support CONFIG_NETDEVICES=y : Enabled PHY selection CONFIG_ETH0_PHY_KSZ8051=y : Select the KSZ8051 PHY (for EMAC), OR - CONFIG_ETH0_PHY_KSZ90x1=y : Select teh KSZ9021/31 PHY (for GMAC) + CONFIG_ETH0_PHY_KSZ90x1=y : Select the KSZ9021/31 PHY (for GMAC) Application Configuration -> Network Utilities CONFIG_NETUTILS_RESOLV=y : Enable host address resolution @@ -812,7 +812,7 @@ HSMCI Card Slots labelled MCI1). The full size SD card slot connects via HSMCI0. The card detect discrete - is available on PB17 (pulled high). The write protect discrete is tied to + is available on PD17 (pulled high). The write protect discrete is tied to ground (via PP6) and not available to software. The slot supports 8-bit wide transfer mode, but the NuttX driver currently uses only the 4-bit wide transfer mode @@ -830,7 +830,7 @@ HSMCI Card Slots PD0 MCI0_CDA The microSD connects vi HSMCI1. The card detect discrete is available on - PB18 (pulled high): + PD18 (pulled high): PD18 MCI1_CD PB20 MCI1_DA0 diff --git a/nuttx/configs/sama5d3x-ek/include/board.h b/nuttx/configs/sama5d3x-ek/include/board.h index d424569c6..1c921ca50 100644 --- a/nuttx/configs/sama5d3x-ek/include/board.h +++ b/nuttx/configs/sama5d3x-ek/include/board.h @@ -151,7 +151,7 @@ * 3. One User momentary Push Button * 4. One Disable CS Push Button * - * Only the momentary push button is controllable by software (labeled + * Only the momentary push button is controllable by software (labelled * "PB_USER1" on the board): * * - PE27. Pressing the switch connect PE27 to grounded. Therefore, PE27 @@ -327,7 +327,7 @@ extern "C" { * * Description: * All SAMA5 architectures must provide the following entry point. This entry point - * is called early in the intitialization -- after all memory has been configured + * is called early in the initialization -- after all memory has been configured * and mapped but before any devices have been initialized. * ************************************************************************************/ diff --git a/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h b/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h index 53980e092..9bb8849a8 100644 --- a/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h +++ b/nuttx/configs/sama5d3x-ek/src/sama5d3x-ek.h @@ -368,7 +368,7 @@ * Only the momentary push button is controllable by software (labeled * "PB_USER1" on the board): * - * - PE27. Pressing the switch connect PE27 to grounded. Therefore, PE27 + * - PE27. Pressing the switch connects PE27 to ground. Therefore, PE27 * must be pulled high internally. When the button is pressed the SAMA5 * will sense "0" is on PE27. */ -- cgit v1.2.3