/**************************************************************************** * configs/pic32mz-starterkit/include/board.h * * Copyright (C) 2015 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #ifndef __CONFIGS_SURE_PIC32MZ_INCLUDE_BOARD_H #define __CONFIGS_SURE_PIC32MZ_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /**************************************************************************** * Pre-Processor Definitions ****************************************************************************/ /* Configuration ************************************************************/ /* Clocking *****************************************************************/ /* Crystal frequencies */ #define BOARD_POSC_FREQ 24000000 /* Primary OSC XTAL frequency (24MHz) */ #define BOARD_SOSC_FREQ 32768 /* Secondary OSC XTAL frequency (32.768KHz) */ /* Oscillator modes */ #define BOARD_FNOSC_SPLL 1 /* Use system PLL */ #define BOARD_POSC_HSMODE 1 /* High-speed crystal (HS) mode */ /* PLL configuration and resulting CPU clock. * CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV */ #define BOARD_PLL_INPUT BOARD_POSC_FREQ #define BOARD_PLL_IDIV 3 /* PLL input divider */ #define BOARD_PLL_MULT 50 /* PLL multiplier */ #define BOARD_PLL_ODIV 2 /* PLL output divider */ #define BOARD_CPU_CLOCK 200000000 /* CPU clock: 200MHz = (24MHz / 3) * 50 / 2) */ /* Peripheral clocks */ /* PBCLK1 * Peripherals: OSC2 pin * * NOTES: * - PBCLK1 is used by system modules and cannot be turned off * - PBCLK1 divided by 2 is available on the OSC2 pin in certain clock * modes. */ #define BOARD_PB1DIV 5 /* Divider = 5 */ #define BOARD_PBCLK1 40000000 /* PBCLK1 frequency = 200MHz/5 = 40MHz */ /* PBCLK2 * Peripherals: PMP, I2C, UART, SPI */ #define BOARD_PBCLK2_ENABLE 1 /* Enable PBCLK2 */ #define BOARD_PB2DIV 5 /* Divider = 5 */ #define BOARD_PBCLK2 40000000 /* PBCLK2 frequency = 200MHz/5 = 40MHz */ /* PBCLK3 * Peripherals: ADC, Comparator, Timers, Output Compare, Input Compare * * NOTES: * - Timer 1 uses SOSC */ #undef BOARD_PBCLK3_ENABLE /* PBCLK4 * Peripherals: Ports */ #define BOARD_PBCLK4_ENABLE 1 /* Enable PBCLK4 */ #define BOARD_PB4DIV 2 /* Divider = 2 */ #define BOARD_PBCLK4 100000000 /* PBCLK4 frequency = 200MHz/2 = 100MHz */ /* PBCLK5 * Peripherals: Flash, Crypto, RND, USB, CAN, Ethernet, SQI * * NOTES: * - PBCLK5 is used to fetch data from/to the Flash Controller, while the * FRC clock is used for programming */ #undef BOARD_PBCLK5_ENABLE /* PBCLK6 * Peripherals: */ #undef BOARD_PBCLK6_ENABLE /* PBCLK7 * Peripherals: CPU, Deadman timer */ #undef BOARD_PBCLK7_ENABLE /* PBCLK8 * Peripherals: EBI */ #undef BOARD_PBCLK8_ENABLE /* Watchdog pre-scaler (re-visit) */ #define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */ /* LED definitions **********************************************************/ /* LED Configuration ********************************************************/ /* The PIC32MZ Ethernet Starter kit has 3 user LEDs labelled LED1-3 on the * board: * * PIN LED Notes * --- ----- ------------------------- * RH0 LED1 High illuminates (RED) * RH1 LED3 High illuminates (YELLOW) * RH2 LED2 High illuminates (GREEN) */ /* LED index values for use with pic32mz_setled() */ #define PIC32MZ_STARTERKIT_LED1 0 #define PIC32MZ_STARTERKIT_LED2 1 #define PIC32MZ_STARTERKIT_LED3 2 #define PIC32MZ_STARTERKIT_NLEDS 3 /* LED bits for use with pic32mz_setleds() */ #define PIC32MZ_STARTERKIT_LED1_BIT (1 << PIC32MZ_STARTERKIT_LED1) #define PIC32MZ_STARTERKIT_LED2_BIT (1 << PIC32MZ_STARTERKIT_LED2) #define PIC32MZ_STARTERKIT_LED3_BIT (1 << PIC32MZ_STARTERKIT_LED3) /* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 3 LEDs * on board the Ethernet Starter Kit. The following definitions * describe how NuttX controls the LEDs: * * ON OFF * ------------------------- ---- ---- ---- ---- ---- ---- * LED1 LED2 LED3 LED1 LED2 LED3 * ------------------------- ---- ---- ---- ---- ---- ---- * LED_STARTED 0 OFF OFF OFF --- --- --- * LED_HEAPALLOCATE 1 ON OFF N/C --- --- --- * LED_IRQSENABLED 2 OFF ON N/C --- --- --- * LED_STACKCREATED 3 ON ON N/C --- --- --- * LED_INIRQ 4 N/C N/C ON N/C N/C OFF * LED_SIGNAL 4 N/C N/C ON N/C N/C OFF * LED_ASSERTION 4 N/C N/C ON N/C N/C OFF * LED_PANIC 5 ON N/C N/C OFF N/C N/C */ #define LED_STARTED 0 #define LED_HEAPALLOCATE 1 #define LED_IRQSENABLED 2 #define LED_STACKCREATED 3 #define LED_INIRQ 4 #define LED_SIGNAL 4 #define LED_ASSERTION 4 #define LED_PANIC 5 #define LED_NVALUES 6 /* Switch definitions *******************************************************/ /* The PIC32MZ Ethernet Starter kit has 3 user push buttons labelled SW1-3 * on the board: * * PIN LED Notes * ---- ---- ------------------------- * RB12 SW1 Active-low * RB13 SW2 Active-low * RB14 SW3 Active-low * * The switches do not have any debounce circuitry and require internal pull- * up resistors. When Idle, the switches are pulled high (+3.3V), and they * are grounded when pressed. */ /**************************************************************************** * Public Types ****************************************************************************/ #ifndef __ASSEMBLY__ /**************************************************************************** * Inline Functions ****************************************************************************/ /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #ifdef __cplusplus #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Name: pic32mz_ledinit and pic32mz_setled * * Description: * If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board * LEDs. If CONFIG_ARCH_LEDS is not defined, then the following interfaces * are available to control the LEDs from user applications. * ****************************************************************************/ #ifndef CONFIG_ARCH_LEDS void pic32mz_ledinit(void); void pic32mz_setled(int led, bool ledon); void pic32mz_setleds(uint8_t ledset); #endif #undef EXTERN #ifdef __cplusplus } #endif #endif /* __ASSEMBLY__ */ #endif /* __CONFIGS_SURE_PIC32MZ_INCLUDE_BOARD_H */