/**************************************************************************** * drivers/net/encx24j600.c * * Copyright (C) 2013-1014 UVC Ingenieure. All rights reserved. * Author: Max Holtzberg * * References: * - ENC424J600/624J600 Data Sheet, Stand-Alone 10/100 Ethernet Controller * with SPI or Parallel Interface, DS39935C, 2010 Microchip Technology Inc. * * Derived from enc28j60 driver written by: * * Copyright (C) 2010-2012 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #if defined(CONFIG_NET) && defined(CONFIG_ENCX24J600) #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "encx24j600.h" /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Configuration ************************************************************/ /* ENCX24J600 Configuration Settings: * * CONFIG_ENCX24J600 - Enabled ENCX24J600 support * CONFIG_ENCX24J600_SPIMODE - Controls the SPI mode * CONFIG_ENCX24J600_FREQUENCY - Define to use a different bus frequency * CONFIG_ENCX24J600_NINTERFACES - Specifies the number of physical ENCX24J600 * devices that will be supported. * CONFIG_ENCX24J600_STATS - Collect network statistics */ /* The ENCX24J600 spec says that it supports SPI mode 0,0 only: "The * implementation used on this device supports SPI mode 0,0 only. In * addition, the SPI port requires that SCK be at Idle in a low state; * selectable clock polarity is not supported." However, sometimes you * need to tinker with these things. */ #ifndef CONFIG_ENCX24J600_SPIMODE # define CONFIG_ENCX24J600_SPIMODE SPIDEV_MODE0 #endif /* CONFIG_ENCX24J600_NINTERFACES determines the number of physical interfaces * that will be supported. */ #ifndef CONFIG_ENCX24J600_NINTERFACES # define CONFIG_ENCX24J600_NINTERFACES 1 #endif /* CONFIG_NET_BUFSIZE must always be defined */ #if !defined(CONFIG_NET_BUFSIZE) && (CONFIG_NET_BUFSIZE <= MAX_FRAMELEN) # error "CONFIG_NET_BUFSIZE is not valid for the ENCX24J600" #endif /* We need to have the work queue to handle SPI interrupts */ #ifndef CONFIG_SCHED_WORKQUEUE # error "Worker thread support is required (CONFIG_SCHED_WORKQUEUE)" #endif /* CONFIG_ENCX24J600_DUMPPACKET will dump the contents of each packet to the console. */ #ifdef CONFIG_ENCX24J600_DUMPPACKET # define enc_dumppacket(m,a,n) lib_dumpbuffer(m,a,n) #else # define enc_dumppacket(m,a,n) #endif /* The ENCX24J600 will not do interrupt level processing */ #ifndef CONFIG_NET_NOINTS # warning "CONFIG_NET_NOINTS should be set" #endif /* Low-level register debug */ #if !defined(CONFIG_DEBUG) || !defined(CONFIG_DEBUG_NET) # undef CONFIG_ENCX24J600_REGDEBUG #endif /* Timing *******************************************************************/ /* TX poll delay = 1 seconds. CLK_TCK is the number of clock ticks per second */ #define ENC_WDDELAY (1*CLK_TCK) #define ENC_POLLHSEC (1*2) /* TX timeout = 1 minute */ #define ENC_TXTIMEOUT (60*CLK_TCK) /* RX timeout (Time packets are held in the RX queue until they are dropped) */ #define ENC_RXTIMEOUT MSEC2TICK(2000) /* Poll timeout */ #define ENC_POLLTIMEOUT MSEC2TICK(50) /* Register poll timeout */ #define ENC_REGPOLLTIMEOUT MSEC2TICK(5000) /* Packet Memory ************************************************************/ /* Packet memory layout */ #define PKTMEM_ALIGNED_BUFSIZE ((CONFIG_NET_BUFSIZE + 1) & ~1) #define PKTMEM_RX_START (PKTMEM_START + PKTMEM_SIZE / 2) /* Followed by RX buffer */ #define PKTMEM_RX_SIZE (PKTMEM_SIZE - PKTMEM_RX_START) #define PKTMEM_RX_END (PKTMEM_START + PKTMEM_SIZE) /* RX buffer goes to the end of SRAM */ /* We use preinitialized TX descriptors */ #define ENC_NTXDESCR ((PKTMEM_RX_START - PKTMEM_START) / PKTMEM_ALIGNED_BUFSIZE) /* This is a helper pointer for accessing the contents of the Ethernet header */ #define BUF ((struct uip_eth_hdr *)priv->dev.d_buf) /* Debug ********************************************************************/ #ifdef CONFIG_ENCX24J600_REGDEBUG # define enc_wrdump(a,v) lowsyslog("ENCX24J600: %02x<-%04x\n", a, v); # define enc_rddump(a,v) lowsyslog("ENCX24J600: %02x->%04x\n", a, v); # define enc_bfsdump(a,m) lowsyslog("ENCX24J600: %02x|=%04x\n", a, m); # define enc_bfcdump(a,m) lowsyslog("ENCX24J600: %02x&=~%04x\n", a, m); # define enc_cmddump(c) lowsyslog("ENCX24J600: CMD: %02x\n", c); # define enc_bmdump(c,b,s) lowsyslog("ENCX24J600: CMD: %02x buffer: %p length: %d\n", c,b,s); #else # define enc_wrdump(a,v) # define enc_rddump(a,v) # define enc_bfsdump(a,m) # define enc_bfcdump(a,m) # define enc_cmddump(c) # define enc_bmdump(c,b,s) #endif /**************************************************************************** * Private Types ****************************************************************************/ /* The state of the interface */ enum enc_state_e { ENCSTATE_UNINIT = 0, /* The interface is in an uninitialized state */ ENCSTATE_DOWN, /* The interface is down */ ENCSTATE_UP, /* The interface is up */ ENCSTATE_RUNNING /* The interface is has a cable plugged in and is ready to use */ }; struct enc_descr_s { struct enc_descr_next *flink; uint16_t addr; uint16_t len; uint32_t ts; /* Timestamp of reception for timeout */ }; /* The enc_driver_s encapsulates all state information for a single hardware * interface */ struct enc_driver_s { /* Device control */ uint8_t ifstate; /* Interface state: See ENCSTATE_* */ uint8_t bank; /* Currently selected bank command */ uint16_t nextpkt; /* Next packet address */ FAR const struct enc_lower_s *lower; /* Low-level MCU-specific support */ /* Timing */ WDOG_ID txpoll; /* TX poll timer */ WDOG_ID txtimeout; /* TX timeout timer */ /* If we don't own the SPI bus, then we cannot do SPI accesses from the * interrupt handler. */ struct work_s irqwork; /* Interrupt continuation work queue support */ struct work_s towork; /* Tx timeout work queue support */ struct work_s pollwork; /* Poll timeout work queue support */ struct enc_descr_s txdescralloc[ENC_NTXDESCR]; struct enc_descr_s rxdescralloc[CONFIG_ENCX24J600_NRXDESCR]; sq_queue_t txfreedescr; /* Free inititialized TX descriptors */ sq_queue_t rxfreedescr; /* Free RX descriptors */ sq_queue_t txqueue; /* Enqueued descriptors waiting for transmition */ sq_queue_t rxqueue; /* Unhandled incoming packets waiting for reception */ /* This is the contained SPI driver intstance */ FAR struct spi_dev_s *spi; /* This holds the information visible to uIP/NuttX */ struct uip_driver_s dev; /* Interface understood by uIP */ /* Statistics */ #ifdef CONFIG_ENCX24J600_STATS struct enc_stats_s stats; #endif }; /**************************************************************************** * Private Data ****************************************************************************/ static struct enc_driver_s g_encx24j600[CONFIG_ENCX24J600_NINTERFACES]; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* Low-level SPI helpers */ #ifdef CONFIG_SPI_OWNBUS static inline void enc_configspi(FAR struct spi_dev_s *spi); # define enc_lock(priv); # define enc_unlock(priv); #else # define enc_configspi(spi) static void enc_lock(FAR struct enc_driver_s *priv); static inline void enc_unlock(FAR struct enc_driver_s *priv); #endif /* SPI control register access */ static inline void enc_setethrst(FAR struct enc_driver_s *priv); static void enc_setbank(FAR struct enc_driver_s *priv, uint8_t bank); static uint16_t enc_rdreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg); static void enc_wrreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t wrdata); static int enc_waitreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits, uint16_t value); static void enc_bfs(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits); static void enc_bfc(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits); static void enc_cmd(FAR struct enc_driver_s *priv, uint8_t cmd, uint16_t arg); #if 0 /* Sometimes useful */ static void enc_rxdump(FAR struct enc_driver_s *priv); static void enc_txdump(FAR struct enc_driver_s *priv); #endif /* SPI buffer transfers */ static void enc_rdbuffer(FAR struct enc_driver_s *priv, FAR uint8_t *buffer, size_t buflen); static inline void enc_wrbuffer(FAR struct enc_driver_s *priv, FAR const uint8_t *buffer, size_t buflen); /* PHY register access */ static uint16_t enc_rdphy(FAR struct enc_driver_s *priv, uint8_t phyaddr); static void enc_wrphy(FAR struct enc_driver_s *priv, uint8_t phyaddr, uint16_t phydata); /* Common TX logic */ static int enc_txenqueue(FAR struct enc_driver_s *priv); static int enc_transmit(FAR struct enc_driver_s *priv); static int enc_uiptxpoll(struct uip_driver_s *dev); /* Common RX logic */ static struct enc_descr_s *enc_rxgetdescr(FAR struct enc_driver_s *priv); static void enc_rxldpkt(FAR struct enc_driver_s *priv, struct enc_descr_s *descr); static void enc_rxrmpkt(FAR struct enc_driver_s *priv, struct enc_descr_s *descr); static void enc_rxdispatch(FAR struct enc_driver_s *priv); /* Interrupt handling */ static void enc_linkstatus(FAR struct enc_driver_s *priv); static void enc_txif(FAR struct enc_driver_s *priv); static void enc_pktif(FAR struct enc_driver_s *priv); static void enc_rxabtif(FAR struct enc_driver_s *priv); static void enc_irqworker(FAR void *arg); static int enc_interrupt(int irq, FAR void *context); /* Watchdog timer expirations */ static void enc_toworker(FAR void *arg); static void enc_txtimeout(int argc, uint32_t arg, ...); static void enc_pollworker(FAR void *arg); static void enc_polltimer(int argc, uint32_t arg, ...); /* NuttX callback functions */ static int enc_ifup(struct uip_driver_s *dev); static int enc_ifdown(struct uip_driver_s *dev); static int enc_txavail(struct uip_driver_s *dev); static int enc_rxavail(struct uip_driver_s *dev); #ifdef CONFIG_NET_IGMP static int enc_addmac(struct uip_driver_s *dev, FAR const uint8_t *mac); static int enc_rmmac(struct uip_driver_s *dev, FAR const uint8_t *mac); #endif /* Initialization */ static void enc_pwrsave(FAR struct enc_driver_s *priv); static void enc_setmacaddr(FAR struct enc_driver_s *priv); static void enc_resetbuffers(FAR struct enc_driver_s *priv); static int enc_reset(FAR struct enc_driver_s *priv); /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Function: enc_configspi * * Description: * Configure the SPI for use with the ENCX24J600 * * Parameters: * spi - Reference to the SPI driver structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #ifdef CONFIG_SPI_OWNBUS static inline void enc_configspi(FAR struct spi_dev_s *spi) { /* Configure SPI for the ENCX24J600. But only if we own the SPI bus. * Otherwise, don't bother because it might change. */ SPI_SETMODE(spi, CONFIG_ENCX24J600_SPIMODE); SPI_SETBITS(spi, 8); SPI_SETFREQUENCY(spi, CONFIG_ENCX24J600_FREQUENCY); } #endif /**************************************************************************** * Function: enc_lock * * Description: * Select the SPI, locking and re-configuring if necessary * * Parameters: * spi - Reference to the SPI driver structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #ifndef CONFIG_SPI_OWNBUS static void enc_lock(FAR struct enc_driver_s *priv) { /* Lock the SPI bus in case there are multiple devices competing for the SPI * bus. */ SPI_LOCK(priv->spi, true); /* Now make sure that the SPI bus is configured for the ENCX24J600 (it * might have gotten configured for a different device while unlocked) */ SPI_SETMODE(priv->spi, CONFIG_ENCX24J600_SPIMODE); SPI_SETBITS(priv->spi, 8); SPI_SETFREQUENCY(priv->spi, CONFIG_ENCX24J600_FREQUENCY); } #endif /**************************************************************************** * Function: enc_unlock * * Description: * De-select the SPI * * Parameters: * spi - Reference to the SPI driver structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #ifndef CONFIG_SPI_OWNBUS static inline void enc_unlock(FAR struct enc_driver_s *priv) { /* Relinquish the lock on the bus. */ SPI_LOCK(priv->spi, false); } #endif /**************************************************************************** * Function: enc_cmd * * Description: * Execute two byte command. * * Parameters: * priv - Reference to the driver state structure * cmd - ENCX24J600 two-byte command * arg - Two byte argument to the command * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_cmd(FAR struct enc_driver_s *priv, uint8_t cmd, uint16_t arg) { DEBUGASSERT(priv && priv->spi); /* Select ENCX24J600 chip */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; (void)SPI_SEND(priv->spi, cmd); /* Clock out the command */ (void)SPI_SEND(priv->spi, arg & 0xff); /* Clock out the low byte */ (void)SPI_SEND(priv->spi, arg >> 8); /* Clock out the high byte */ /* De-select ENCX24J600 chip. */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_wrdump(cmd, arg); } /**************************************************************************** * Function: enc_setethrst * * Description: * Issues System Reset by setting ETHRST (ECON2<4>) * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static inline void enc_setethrst(FAR struct enc_driver_s *priv) { DEBUGASSERT(priv && priv->spi); /* Select ENC28J60 chip */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; /* Send the system reset command. */ (void)SPI_SEND(priv->spi, ENC_SETETHRST); up_udelay(25); /* De-select ENC28J60 chip. */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_cmddump(ENC_SETETHRST); } /**************************************************************************** * Function: enc_setbank * * Description: * Set the bank for the next control register access. * * Assumption: * The caller has exclusive access to the SPI bus * * Parameters: * priv - Reference to the driver state structure * bank - SPI command to select the bank with * * Returned Value: * None * * Assumptions: * The chip is selected and SPI is ready for communication. * ****************************************************************************/ static void enc_setbank(FAR struct enc_driver_s *priv, uint8_t bank) { /* Check if a bank has to be set and if the bank setting has changed. * For registers that are available on all banks, the bank command is set to 0. */ if (bank != 0 && bank != priv->bank) { /* Select bank with supplied command */ SPI_SEND(priv->spi, bank); /* Then remember the bank setting */ priv->bank = bank; } } /**************************************************************************** * Function: enc_rdreg * * Description: * Read one word from a control register using the RCR command. * * Parameters: * priv - Reference to the driver state structure * ctrlreg - Bit encoded address of banked register to read * * Returned Value: * The byte read from the banked register * * Assumptions: * ****************************************************************************/ static uint16_t enc_rdreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg) { uint16_t rddata; DEBUGASSERT(priv && priv->spi); DEBUGASSERT((ctrlreg & 0xe0) == 0); /* banked regeitsers only */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true); enc_setbank(priv, GETBANK(ctrlreg)); SPI_SEND(priv->spi, ENC_RCR | GETADDR(ctrlreg)); rddata = SPI_SEND(priv->spi, 0); /* Clock in the low byte */ rddata |= SPI_SEND(priv->spi, 0) << 8; /* Clock in the high byte */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_rddump(GETADDR(ctrlreg), rddata); return rddata; } /**************************************************************************** * Function: enc_wrreg * * Description: * Write one word to a control register using the WCR command. * * Parameters: * priv - Reference to the driver state structure * ctrlreg - Bit encoded address of banked register to write * wrdata - The data to send * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_wrreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t wrdata) { DEBUGASSERT(priv && priv->spi); DEBUGASSERT((ctrlreg & 0xe0) == 0); /* banked regeitsers only */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; enc_setbank(priv, GETBANK(ctrlreg)); SPI_SEND(priv->spi, ENC_WCR | GETADDR(ctrlreg)); SPI_SEND(priv->spi, wrdata & 0xff); /* Clock out the low byte */ SPI_SEND(priv->spi, wrdata >> 8); /* Clock out the high byte */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_wrdump(GETADDR(ctrlreg), wrdata); } /**************************************************************************** * Function: enc_waitbreg * * Description: * Wait until banked register bit(s) take a specific value (or a timeout * occurs). * * Parameters: * priv - Reference to the driver state structure * ctrlreg - Bit encoded address of banked register to check * bits - The bits to check (a mask) * value - The value of the bits to return (value under mask) * * Returned Value: * OK on success, negated errno on failure * * Assumptions: * ****************************************************************************/ static int enc_waitreg(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits, uint16_t value) { uint32_t start = clock_systimer(); uint32_t elapsed; uint16_t rddata; /* Loop until the exit condition is met */ do { /* Read the byte from the requested banked register */ rddata = enc_rdreg(priv, ctrlreg); elapsed = clock_systimer() - start; } while ((rddata & bits) != value && elapsed < ENC_REGPOLLTIMEOUT); return (rddata & bits) == value ? OK : -ETIMEDOUT; } /**************************************************************************** * Function: enc_bfs * * Description: * Bit Field Set. * * Parameters: * priv - Reference to the driver state structure * ctrlreg - Bit encoded address of banked register to set bits in * bits - The bits to set (a mask) * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_bfs(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits) { DEBUGASSERT(priv && priv->spi); /* Select ENCX24J600 chip */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; /* Set the bank */ enc_setbank(priv, GETBANK(ctrlreg)); /* Send the BFS command and data. The sequence requires 24-clocks: * 8 to clock out the cmd + 16 to clock out the data. */ (void)SPI_SEND(priv->spi, ENC_BFS | GETADDR(ctrlreg)); /* Clock out the command */ (void)SPI_SEND(priv->spi, bits & 0xff); /* Clock out the low byte */ (void)SPI_SEND(priv->spi, bits >> 8); /* Clock out the high byte */ /* De-select ENCX24J600 chip. */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_bfsdump(GETADDR(ctrlreg), bits); } /**************************************************************************** * Function: enc_bfc * * Description: * Bit Field Clear. * * Parameters: * priv - Reference to the driver state structure * ctrlreg - Bit encoded address of banked register to clear bits in * bits - The bits to clear (a mask) * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_bfc(FAR struct enc_driver_s *priv, uint16_t ctrlreg, uint16_t bits) { DEBUGASSERT(priv && priv->spi); /* Select ENCX24J600 chip */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; /* Set the bank */ enc_setbank(priv, GETBANK(ctrlreg)); /* Send the BFC command and data. The sequence requires 24-clocks: * 8 to clock out the cmd + 16 to clock out the data. */ (void)SPI_SEND(priv->spi, ENC_BFC | GETADDR(ctrlreg)); /* Clock out the command */ (void)SPI_SEND(priv->spi, bits & 0xff); /* Clock out the low byte */ (void)SPI_SEND(priv->spi, bits >> 8); /* Clock out the high byte */ /* De-select ENCX24J600 chip. */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_bfcdump(GETADDR(ctrlreg), bits); } /**************************************************************************** * Function: enc_txdump enc_rxdump * * Description: * Dump registers associated with receiving or sending packets. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #if 0 /* Sometimes useful */ static void enc_rxdump(FAR struct enc_driver_s *priv) { lowsyslog("Rx Registers:\n"); lowsyslog(" EIE: %02x EIR: %02x\n", enc_rdgreg(priv, ENC_EIE), enc_rdgreg(priv, ENC_EIR)); lowsyslog(" ESTAT: %02x ECON1: %02x ECON2: %02x\n", enc_rdgreg(priv, ENC_ESTAT), enc_rdgreg(priv, ENC_ECON1), enc_rdgreg(priv, ENC_ECON2)); lowsyslog(" ERXST: %02x %02x\n", enc_rdbreg(priv, ENC_ERXSTH), enc_rdbreg(priv, ENC_ERXSTL)); lowsyslog(" ERXND: %02x %02x\n", enc_rdbreg(priv, ENC_ERXNDH), enc_rdbreg(priv, ENC_ERXNDL)); lowsyslog(" ERXRDPT: %02x %02x\n", enc_rdbreg(priv, ENC_ERXRDPTH), enc_rdbreg(priv, ENC_ERXRDPTL)); lowsyslog(" ERXFCON: %02x EPKTCNT: %02x\n", enc_rdbreg(priv, ENC_ERXFCON), enc_rdbreg(priv, ENC_EPKTCNT)); lowsyslog(" MACON1: %02x MACON3: %02x\n", enc_rdbreg(priv, ENC_MACON1), enc_rdbreg(priv, ENC_MACON3)); lowsyslog(" MAMXFL: %02x %02x\n", enc_rdbreg(priv, ENC_MAMXFLH), enc_rdbreg(priv, ENC_MAMXFLL)); lowsyslog(" MAADR: %02x:%02x:%02x:%02x:%02x:%02x\n", enc_rdbreg(priv, ENC_MAADR1), enc_rdbreg(priv, ENC_MAADR2), enc_rdbreg(priv, ENC_MAADR3), enc_rdbreg(priv, ENC_MAADR4), enc_rdbreg(priv, ENC_MAADR5), enc_rdbreg(priv, ENC_MAADR6)); } #endif #if 0 /* Sometimes useful */ static void enc_txdump(FAR struct enc_driver_s *priv) { lowsyslog("Tx Registers:\n"); lowsyslog(" EIE: %02x EIR: %02x ESTAT: %02x\n", enc_rdgreg(priv, ENC_EIE), enc_rdgreg(priv, ENC_EIR),); lowsyslog(" ESTAT: %02x ECON1: %02x\n", enc_rdgreg(priv, ENC_ESTAT), enc_rdgreg(priv, ENC_ECON1)); lowsyslog(" ETXST: %02x %02x\n", enc_rdbreg(priv, ENC_ETXSTH), enc_rdbreg(priv, ENC_ETXSTL)); lowsyslog(" ETXND: %02x %02x\n", enc_rdbreg(priv, ENC_ETXNDH), enc_rdbreg(priv, ENC_ETXNDL)); lowsyslog(" MACON1: %02x MACON3: %02x MACON4: %02x\n", enc_rdbreg(priv, ENC_MACON1), enc_rdbreg(priv, ENC_MACON3), enc_rdbreg(priv, ENC_MACON4)); lowsyslog(" MACON1: %02x MACON3: %02x MACON4: %02x\n", enc_rdbreg(priv, ENC_MACON1), enc_rdbreg(priv, ENC_MACON3), enc_rdbreg(priv, ENC_MACON4)); lowsyslog(" MABBIPG: %02x MAIPG %02x %02x\n", enc_rdbreg(priv, ENC_MABBIPG), enc_rdbreg(priv, ENC_MAIPGH), enc_rdbreg(priv, ENC_MAIPGL)); lowsyslog(" MACLCON1: %02x MACLCON2: %02x\n", enc_rdbreg(priv, ENC_MACLCON1), enc_rdbreg(priv, ENC_MACLCON2)); lowsyslog(" MAMXFL: %02x %02x\n", enc_rdbreg(priv, ENC_MAMXFLH), enc_rdbreg(priv, ENC_MAMXFLL)); } #endif /**************************************************************************** * Function: enc_rdbuffer * * Description: * Read a buffer of data from RX Data Buffer. * * Parameters: * priv - Reference to the driver state structure * buffer - A pointer to the buffer to read into * buflen - The number of bytes to read * * Returned Value: * None * * Assumptions: * RX Data pointer is set to the correct address * ****************************************************************************/ static void enc_rdbuffer(FAR struct enc_driver_s *priv, FAR uint8_t *buffer, size_t buflen) { DEBUGASSERT(priv && priv->spi); /* Select ENCX24J600 chip */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true); /* Send the read buffer memory command (ignoring the response) */ (void)SPI_SEND(priv->spi, ENC_RRXDATA); /* Then read the buffer data */ SPI_RECVBLOCK(priv->spi, buffer, buflen); /* De-select ENCX24J600 chip. */ SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_bmdump(ENC_RRXDATA, buffer, buflen); } /**************************************************************************** * Function: enc_wrbuffer * * Description: * Write a buffer of data. * * Parameters: * priv - Reference to the driver state structure * buffer - A pointer to the buffer to write from * buflen - The number of bytes to write * * Returned Value: * None * * Assumptions: * General Purpose Write pointer is set to the correct address * ****************************************************************************/ static inline void enc_wrbuffer(FAR struct enc_driver_s *priv, FAR const uint8_t *buffer, size_t buflen) { DEBUGASSERT(priv && priv->spi); SPI_SELECT(priv->spi, SPIDEV_ETHERNET, true);; SPI_SEND(priv->spi, ENC_WGPDATA); SPI_SNDBLOCK(priv->spi, buffer, buflen); SPI_SELECT(priv->spi, SPIDEV_ETHERNET, false); enc_bmdump(ENC_WGPDATA, buffer, buflen); } /**************************************************************************** * Function: enc_rdphy * * Description: * Read 16-bits of PHY data. * * Parameters: * priv - Reference to the driver state structure * phyaddr - The PHY register address * * Returned Value: * 16-bit value read from the PHY * * Assumptions: * ****************************************************************************/ static uint16_t enc_rdphy(FAR struct enc_driver_s *priv, uint8_t phyaddr) { uint16_t data = 0; /* "To read from a PHY register: * 1. Write the address of the PHY register to read from into the MIREGADR * register (Register 3-1). Make sure to also set reserved bit 8 of this * register. */ enc_wrreg(priv, ENC_MIREGADR, phyaddr); /* 2. Set the MIIRD bit (MICMD<0>, Register 3-2). The read operation begins * and the BUSY bit (MISTAT<0>, Register 3-3) is automatically set by * hardware. */ enc_bfs(priv, ENC_MICMD, MICMD_MIIRD); /* 3. Wait 25.6 μs. Poll the BUSY (MISTAT<0>) bit to be certain that the * operation is complete. While busy, the host controller should not * start any MIISCAN operations or write to the MIWR register. When the * MAC has obtained the register contents, the BUSY bit will clear * itself. */ up_udelay(26); if (enc_waitreg(priv, ENC_MISTAT, MISTAT_BUSY, 0x00) == OK) { /* 4. Clear the MIIRD (MICMD<0>) bit. */ enc_bfc(priv, ENC_MICMD, MICMD_MIIRD); /* 5. Read the desired data from the MIRD register. For 8-bit interfaces, * the order that these bytes are read is unimportant." */ data = enc_rdreg(priv, ENC_MIRD); } return data; } /**************************************************************************** * Function: enc_wrphy * * Description: * write 16-bits of PHY data. * * Parameters: * priv - Reference to the driver state structure * phyaddr - The PHY register address * phydata - 16-bit data to write to the PHY * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_wrphy(FAR struct enc_driver_s *priv, uint8_t phyaddr, uint16_t phydata) { /* "To write to a PHY register: * * 1. Write the address of the PHY register to write to into the MIREGADR * register. Make sure to also set reserved bit 8 of this register. */ enc_wrreg(priv, ENC_MIREGADR, 0x0100 | phyaddr); /* 2. Write the 16 bits of data into the MIWR register. The low byte must * be written first, followed by the high byte. */ enc_wrreg(priv, ENC_MIWR, phydata); /* 3. Writing to the high byte of MIWR begins the MIIM transaction and the * BUSY (MISTAT<0>) bit is automatically set by hardware. * * The PHY register is written after the MIIM operation completes, which takes * 25.6 μs. When the write operation has completed, the BUSY bit clears * itself. The host controller should not start any MIISCAN, MIWR or MIIRD * operations while the BUSY bit is set. */ up_udelay(26); enc_waitreg(priv, ENC_MISTAT, MISTAT_BUSY, 0); } /**************************************************************************** * Function: enc_transmit * * Description: * Start hardware transmission. Called either from: * * - pkif interrupt when an application responds to the receipt of data * by trying to send something, or * - From watchdog based polling. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * OK on success; a negated errno on failure * * Assumptions: * ****************************************************************************/ static int enc_transmit(FAR struct enc_driver_s *priv) { struct enc_descr_s *descr; /* dequeue next packet to transmit */ descr = (struct enc_descr_s*)sq_remfirst(&priv->txqueue); DEBUGASSERT(descr != NULL); /* Verify that the hardware is ready to send another packet. The driver * starts a transmission process by setting ECON1.TXRTS. When the packet is * finished transmitting or is aborted due to an error/cancellation, the * ECON1.TXRTS bit will be cleared. * * NOTE: If we got here, then we have committed to sending a packet. * higher level logic must have assured that (1) there is no transmission * in progress, and that (2) TX-related interrupts are disabled. */ DEBUGASSERT((enc_rdreg(priv, ENC_ECON1) & ECON1_TXRTS) == 0); /* Set TXStart and TXLen registers. */ enc_wrreg(priv, ENC_ETXST, descr->addr); enc_wrreg(priv, ENC_ETXLEN, descr->len); /* Set TXRTS to send the packet in the transmit buffer */ enc_bfs(priv, ENC_ECON1, ECON1_TXRTS); /* Setup the TX timeout watchdog (perhaps restarting the timer). Note: * Is there a race condition. Could the TXIF interrupt occur before * the timer is started? */ (void)wd_start(priv->txtimeout, ENC_TXTIMEOUT, enc_txtimeout, 1, (uint32_t)priv); /* free the descriptor */ sq_addlast((sq_entry_t*)descr, &priv->txfreedescr); return OK; } /**************************************************************************** * Function: enc_txenqueue * * Description: * Write packet from d_buf to the enc's SRAM if a free descriptor is available. * The filled descriptor is enqueued for transmission. * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * OK on success; a negated errno on failure * * Assumptions: * A packet is available in d_buf. * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static int enc_txenqueue(FAR struct enc_driver_s *priv) { int ret = OK; struct enc_descr_s *descr; DEBUGASSERT(priv->dev.d_len > 0); /* Increment statistics */ #ifdef CONFIG_ENCX24J600_STATS priv->stats.txrequests++; #endif descr = (struct enc_descr_s*)sq_remfirst(&priv->txfreedescr); if (descr != NULL) { enc_dumppacket("Write packet to enc SRAM", priv->dev.d_buf, priv->dev.d_len); /* Copy the packet into the transmit buffer described by the current * tx descriptor */ enc_cmd(priv, ENC_WGPWRPT, descr->addr); enc_wrbuffer(priv, priv->dev.d_buf, priv->dev.d_len); /* store packet length */ descr->len = priv->dev.d_len; /* enqueue packet */ sq_addlast((sq_entry_t*)descr, &priv->txqueue); /* if currently no transmission is active, trigger the transmission */ if ((enc_rdreg(priv, ENC_ECON1) & ECON1_TXRTS) == 0) { enc_transmit(priv); } } else { nlldbg("no free descriptors\n"); ret = -ENOMEM; } return ret; } /**************************************************************************** * Function: enc_uiptxpoll * * Description: * Enqueues uIP packets if available. * This is a callback from uip_poll(). uip_poll() may be called: * * 1. When the preceding TX packet send is complete, * 2. When the preceding TX packet send timedout and the interface is reset * 3. During normal TX polling * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * OK on success; a negated errno on failure * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static int enc_uiptxpoll(struct uip_driver_s *dev) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; int ret = OK; /* If the polling resulted in data that should be sent out on the network, * the field d_len is set to a value > 0. */ nllvdbg("Poll result: d_len=%d\n", priv->dev.d_len); if (priv->dev.d_len > 0) { arp_out(&priv->dev); ret = enc_txenqueue(priv); } /* If zero is returned, the polling will continue until all connections have * been examined. */ return ret; } /**************************************************************************** * Function: enc_linkstatus * * Description: * The current link status can be obtained from the PHSTAT1.LLSTAT or * PHSTAT2.LSTAT. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_linkstatus(FAR struct enc_driver_s *priv) { uint16_t regval; /* Before transmitting the first packet after link establishment or * auto-negotiation, the MAC duplex configuration must be manually set to * match the duplex configuration of the PHY. To do this, configure * FULDPX (MACON2<0>) to match PHYDPX (ESTAT<10>). */ regval = enc_rdreg(priv, ENC_ESTAT); if (regval & ESTAT_PHYLNK) { if (regval & ESTAT_PHYDPX) { /* Configure full-duplex */ enc_wrreg(priv, ENC_MABBIPG, 0x15); enc_bfs(priv, ENC_MACON2, MACON2_FULDPX); } else { /* Configure half-duplex */ enc_wrreg(priv, ENC_MABBIPG, 0x12); enc_bfc(priv, ENC_MACON2, MACON2_FULDPX); } netdev_carrier_on(&priv->dev); priv->ifstate = ENCSTATE_RUNNING; } else { netdev_carrier_off(&priv->dev); priv->ifstate = ENCSTATE_UP; } } /**************************************************************************** * Function: enc_txif * * Description: * An TXIF interrupt was received indicating that the last TX packet(s) is * done * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_txif(FAR struct enc_driver_s *priv) { if (sq_empty(&priv->txqueue)) { /* If no further xmits are pending, then cancel the TX timeout */ wd_cancel(priv->txtimeout); /* Poll for uip packets */ uip_poll(&priv->dev, enc_uiptxpoll); } else { /* process txqueue */ enc_transmit(priv); } } /**************************************************************************** * Function: enc_rxldpkt * * Description: * Load packet from the enc's RX buffer to the uip d_buf. * * Parameters: * priv - Reference to the driver state structure * descr - Reference to the descriptor that should be loaded * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_rxldpkt(FAR struct enc_driver_s *priv, struct enc_descr_s *descr) { DEBUGASSERT(priv != NULL && descr != NULL); nllvdbg("load packet @%04x len: %d\n", descr->addr, descr->len); /* Set the rx data pointer to the start of the received packet (ERXRDPT) */ enc_cmd(priv, ENC_WRXRDPT, descr->addr); /* Save the packet length (without the 4 byte CRC) in priv->dev.d_len */ priv->dev.d_len = descr->len - 4; /* Copy the data data from the receive buffer to priv->dev.d_buf */ enc_rdbuffer(priv, priv->dev.d_buf, priv->dev.d_len); enc_dumppacket("loaded RX packet", priv->dev.d_buf, priv->dev.d_len); } /**************************************************************************** * Function: enc_rxgetdescr * * Description: * Check for a free descriptor in the free list. If no free descriptor is * available a pending descriptor will be freed and returned * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * A free rx descriptor * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static struct enc_descr_s *enc_rxgetdescr(FAR struct enc_driver_s *priv) { if (sq_empty(&priv->rxfreedescr)) { DEBUGASSERT(sq_peek(&priv->rxqueue) != NULL); /* Packets are held in the enc's SRAM until the space is needed */ enc_rxrmpkt(priv, (struct enc_descr_s*)sq_peek(&priv->rxqueue)); } return (struct enc_descr_s*)sq_remfirst(&priv->rxfreedescr); } /**************************************************************************** * Function: enc_rxrmpkt * * Description: * Remove packet from the RX queue and free the block of memory in the enc's * SRAM. * * Parameters: * priv - Reference to the driver state structure * descr - Reference to the descriptor that should be freed * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_rxrmpkt(FAR struct enc_driver_s *priv, struct enc_descr_s *descr) { uint16_t addr; nllvdbg("free descr: %p\n", descr); /* If it is the last descriptor in the queue, advance ERXTAIL. * This way it is possible that gaps occcur. Maybe pending packets * can be reordered th enc's DMA to free RX space? */ if (descr != NULL) { if (descr == (struct enc_descr_s*)sq_peek(&priv->rxqueue)) { /* Wrap address properly around */ addr = (descr->addr - PKTMEM_RX_START + descr->len - 2 + PKTMEM_RX_SIZE) % PKTMEM_RX_SIZE + PKTMEM_RX_START; DEBUGASSERT(addr >= PKTMEM_RX_START && addr < PKTMEM_RX_END); nllvdbg("ERXTAIL %04x\n", addr); enc_wrreg(priv, ENC_ERXTAIL, addr); /* Remove packet from RX queue */ sq_remfirst(&priv->rxqueue); } else { /* Remove packet from RX queue */ sq_rem((sq_entry_t*)descr, &priv->rxqueue); } sq_addlast((sq_entry_t*)descr, &priv->rxfreedescr); } } /**************************************************************************** * Function: enc_rxdispatch * * Description: * Give the newly received packet to uIP. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_rxdispatch(FAR struct enc_driver_s *priv) { struct enc_descr_s *descr; struct enc_descr_s *next; int ret = ERROR; /* Process the RX queue */ descr = (struct enc_descr_s*)sq_peek(&priv->rxqueue); while (descr != NULL) { /* Store the next pointer, because removing the item from list will set * flink to NULL */ next = (struct enc_descr_s*)sq_next(descr); /* Load the packet from the enc's SRAM */ enc_rxldpkt(priv, descr); /* We only accept IP packets of the configured type and ARP packets */ #ifdef CONFIG_NET_IPv6 if (BUF->type == HTONS(UIP_ETHTYPE_IP6)) #else if (BUF->type == HTONS(UIP_ETHTYPE_IP)) #endif { nllvdbg("Try to process IP packet (%02x)\n", BUF->type); arp_ipin(&priv->dev); ret = uip_input(&priv->dev); if (ret == OK || (clock_systimer() - descr->ts) > ENC_RXTIMEOUT) { /* If packet has been sucessfully processed or has timed out, * free it. */ enc_rxrmpkt(priv, descr); } /* If the above function invocation resulted in data that should be * sent out on the network, the field d_len will set to a value > 0. */ if (priv->dev.d_len > 0) { arp_out(&priv->dev); enc_txenqueue(priv); } } else if (BUF->type == htons(UIP_ETHTYPE_ARP)) { nllvdbg("ARP packet received (%02x)\n", BUF->type); arp_arpin(&priv->dev); /* ARP packets are freed immediately */ enc_rxrmpkt(priv, descr); /* If the above function invocation resulted in data that should be * sent out on the network, the field d_len will set to a value > 0. */ if (priv->dev.d_len > 0) { enc_txenqueue(priv); } } else { /* free unsupported packet */ enc_rxrmpkt(priv, descr); nlldbg("Unsupported packet type dropped (%02x)\n", htons(BUF->type)); } descr = next; } } /**************************************************************************** * Function: enc_pktif * * Description: * An interrupt was received indicating the availability of a new RX packet * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_pktif(FAR struct enc_driver_s *priv) { struct enc_descr_s *descr; uint8_t rsv[8]; uint16_t pktlen; uint32_t rxstat; uint16_t curpkt; int pktcnt; DEBUGASSERT(priv->nextpkt >= PKTMEM_RX_START && priv->nextpkt < PKTMEM_RX_END); /* Enqueue all pending packets to the RX queue until PKTCNT == 0 or * no more descriptors are available. */ pktcnt = (enc_rdreg(priv, ENC_ESTAT) & ESTAT_PKTCNT_MASK) >> ESTAT_PKTCNT_SHIFT; while (pktcnt > 0) { curpkt = priv->nextpkt; /* Set the rx data pointer to the start of the received packet (ERXRDPT) */ enc_cmd(priv, ENC_WRXRDPT, curpkt); /* Read the next packet pointer and the 6 byte read status vector (RSV) * at the beginning of the received packet. (ERXRDPT should auto-increment * and wrap to the beginning of the read buffer as necessary) */ enc_rdbuffer(priv, rsv, 8); /* Decode the new next packet pointer, and the RSV. The * RSV is encoded as: * * Bits 0-15: Indicates length of the received frame. This includes the * destination address, source address, type/length, data, * padding and CRC fields. This field is stored in little- * endian format. * Bits 16-47: Bit encoded RX status. */ priv->nextpkt = (uint16_t)rsv[1] << 8 | (uint16_t)rsv[0]; pktlen = (uint16_t)rsv[3] << 8 | (uint16_t)rsv[2]; rxstat = (uint32_t)rsv[7] << 24 | (uint32_t)rsv[6] << 16 | (uint32_t)rsv[5] << 8 | (uint32_t)rsv[4]; nllvdbg("Receiving packet, nextpkt: %04x pktlen: %d rxstat: %08x pktcnt: %d\n", priv->nextpkt, pktlen, rxstat, pktcnt); /* We enqueue the packet first and remove it later if its faulty. * This way we avoid freeing packets that are not processed yet. */ descr = enc_rxgetdescr(priv); /* Set current timestamp */ descr->ts = clock_systimer(); /* Store the start address of the frame without the enc's header */ descr->addr = curpkt + 8; descr->len = pktlen; sq_addlast((sq_entry_t*)descr, &priv->rxqueue); /* Check if the packet was received OK */ if ((rxstat & RXSTAT_OK) == 0) { nlldbg("ERROR: RXSTAT: %08x\n", rxstat); /* Discard packet */ enc_rxrmpkt(priv, descr); #ifdef CONFIG_ENCX24J600_STATS priv->stats.rxnotok++; #endif } /* Check for a usable packet length (4 added for the CRC) */ else if (pktlen > (CONFIG_NET_BUFSIZE + 4) || pktlen <= (UIP_LLH_LEN + 4)) { nlldbg("Bad packet size dropped (%d)\n", pktlen); /* Discard packet */ enc_rxrmpkt(priv, descr); #ifdef CONFIG_ENCX24J600_STATS priv->stats.rxpktlen++; #endif } /* Decrement PKTCNT */ enc_bfs(priv, ENC_ECON1, ECON1_PKTDEC); /* Try to process the packet */ enc_rxdispatch(priv); /* Read out again, maybe there has another packet arrived */ pktcnt = (enc_rdreg(priv, ENC_ESTAT) & ESTAT_PKTCNT_MASK) >> ESTAT_PKTCNT_SHIFT; } } /**************************************************************************** * Function: enc_rxabtif * * Description: * An interrupt was received indicating the abortion of an RX packet * * "The receive abort interrupt occurs when the reception of a frame has been * aborted. A frame being received is aborted when the Head Pointer attempts * to overrun the Tail Pointer, or when the packet counter has reached FFh. * In either case, the receive buffer is full and cannot fit the incoming * frame, so the packet has been dropped. * This interrupt does not occur when packets are dropped due to the receive * filters rejecting a packet. The interrupt should be cleared by software * once it has been serviced." * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * Interrupts are enabled but the caller holds the uIP lock. * ****************************************************************************/ static void enc_rxabtif(FAR struct enc_driver_s *priv) { struct enc_descr_s *descr; #if 0 /* Free the last received packet from the RX queue */ nlldbg("rx abort\n"); nlldbg("ESTAT: %04x\n", enc_rdreg(priv, ENC_ESTAT)); nlldbg("EIR: %04x\n", enc_rdreg(priv, ENC_EIR)); nlldbg("ERXTAIL: %04x\n", enc_rdreg(priv, ENC_ERXTAIL)); nlldbg("ERXHAED: %04x\n", enc_rdreg(priv, ENC_ERXHEAD)); descr = (struct enc_descr_s*)sq_peek(&priv->rxqueue); while (descr != NULL) { nlldbg("addr: %04x len: %d\n", descr->addr, descr->len); descr = (struct enc_descr_s*)sq_next(descr); } DEBUGASSERT(false); #endif descr = (struct enc_descr_s*)sq_peek(&priv->rxqueue); if (descr != NULL) { enc_rxrmpkt(priv, descr); nlldbg("pending packet freed\n"); } else { /* If no pending packet blocks the reception, reset all buffers */ enc_resetbuffers(priv); } } /**************************************************************************** * Function: enc_irqworker * * Description: * Perform interrupt handling logic outside of the interrupt handler (on * the work queue thread). * * Parameters: * arg - The reference to the driver structure (case to void*) * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_irqworker(FAR void *arg) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)arg; uip_lock_t lock; uint16_t eir; DEBUGASSERT(priv); /* Get exclusive access to both uIP and the SPI bus. */ lock = uip_lock(); enc_lock(priv); /* A good practice is for the host controller to clear the Global Interrupt * Enable bit, INTIE (EIE<15>), immediately after an interrupt event. This * causes the interrupt pin to return to the non-asserted (high) state. Once * the interrupt has been serviced, the INTIE bit is set again to re-enable * interrupts. If a new interrupt occurs while servicing another, the act of * resetting the global enable bit will cause a new falling edge to occur on * the interrupt pin and ensure that the host does not miss any events */ enc_bfc(priv, ENC_EIE, EIE_INTIE); /* Loop until all interrupts have been processed (EIR==0). Note that * there is no infinite loop check... if there are always pending interrupts, * we are just broken. */ while ((eir = enc_rdreg(priv, ENC_EIR) & EIR_ALLINTS) != 0) { /* Handle interrupts according to interrupt register register bit * settings. */ nllvdbg("EIR: %04x\n", eir); if ((eir & EIR_DMAIF) != 0) /* DMA interrupt */ { /* Not used by this driver. Just clear the interrupt request. */ enc_bfc(priv, ENC_EIR, EIR_DMAIF); } /* LINKIF: The link change interrupt occurs when the PHY link status * changes. This flag is set by hardware when a link has either been * established or broken between the device and a remote Ethernet partner. * The current link status can be read from PHYLNK (ESTAT<8>). The * interrupt should be cleared by software once it has been serviced. * * To enable the link change interrupt, set LINKIE (EIE<11>). */ if ((eir & EIR_LINKIF) != 0) /* PHY Link Status Change */ { enc_linkstatus(priv); /* Get current link status */ enc_bfc(priv, ENC_EIR, EIR_LINKIF); /* Clear the LINKIF interrupt */ } /* The transmit complete interrupt occurs when the transmission of a * frame has ended (whether or not it was successful). This flag is set * when TXRTS (ECON1<1>) is cleared. The interrupt should be cleared by * software once it has been serviced. */ if ((eir & EIR_TXIF) != 0) /* Transmit Done */ { enc_txif(priv); enc_bfc(priv, ENC_EIR, EIR_TXIF); } /* The receive abort interrupt occurs when the reception of a frame has * been aborted. A frame being received is aborted when the Head Pointer * attempts to overrun the Tail Pointer, or when the packet counter has * reached FFh. In either case, the receive buffer is full and cannot fit * the incoming frame, so the packet has been dropped. This interrupt does * not occur when packets are dropped due to the receive filters rejecting * a packet. The interrupt should be cleared by software once it has been * serviced. * * To enable the receive abort interrupt, set RXABTIE (EIE<1>). * The corresponding interrupt flag is RXABTIF (EIR<1>). */ if ((eir & EIR_RXABTIF) != 0) /* Receive Abort */ { #ifdef CONFIG_ENCX24J600_STATS priv->stats.rxerifs++; #endif enc_rxabtif(priv); enc_bfc(priv, ENC_EIR, EIR_RXABTIF); /* Clear the RXABTIF interrupt */ } /* The received packet pending interrupt occurs when one or more frames * have been received and are ready for software processing. This flag is * set when the PKTCNT<7:0> (ESTAT<7:0>) bits are non-zero. This interrupt * flag is read-only and will automatically clear when the PKTCNT bits are * decremented to zero. For more details about receiving and processing * incoming frames, refer to Section 9.0 "Transmitting and Receiving * Packets". * * To enable the received packet pending interrupt, set PKTIE (EIE<6>). * The corresponding interrupt flag is PKTIF (EIR<6>). */ if ((eir & EIR_PKTIF) != 0 /* RX Packet Pending */ && (enc_rdreg(priv, ENC_ESTAT) & ESTAT_PKTCNT_MASK) != 0) { enc_pktif(priv); /* Handle packet receipt */ /* No clearing necessary, after PKTCNT == 0 the bit is automatically * cleared. This means we will loop until all packets are processed. */ } #ifdef CONFIG_ENCX24J600_STATS /* The transmit abort interrupt occurs when the transmission of a frame * has been aborted. An abort can occur for any of the following reasons: * * * Excessive collisions occurred as defined by the Retransmission * Maximum, MAXRET<3:0> bits (MACLCON<3:0>), setting. If this occurs, * the COLCNT bits (ETXSTAT<3:0>) will indicate the number of collisions * that occurred. * * * A late collision occurred after 63 bytes were transmitted. If this * occurs, LATECOL (ETXSTAT<10>) will be set. * * * The medium was busy and the packet was deferred. If this occurs, * EXDEFER (ETXSTAT<8>) will be set. * * * The application aborted the transmission by clearing TXRTS * (ECON1<1>). * * The interrupt should be cleared by software once it has been serviced. * To enable the transmit abort interrupt, set TXABTIE (EIE<2>). */ if ((eir & EIR_TXABTIF) != 0) /* Transmit Abort */ { priv->stats.txerifs++; enc_bfc(priv, ENC_EIR, EIR_TXABTIF); /* Clear the TXABTIF interrupt */ } #endif } /* Enable GPIO interrupts */ priv->lower->enable(priv->lower); /* Enable Ethernet interrupts */ enc_bfs(priv, ENC_EIE, EIE_INTIE); /* Release lock on the SPI bus and uIP */ enc_unlock(priv); uip_unlock(lock); } /**************************************************************************** * Function: enc_interrupt * * Description: * Hardware interrupt handler * * Parameters: * irq - Number of the IRQ that generated the interrupt * context - Interrupt register state save info (architecture-specific) * * Returned Value: * OK on success * * Assumptions: * ****************************************************************************/ static int enc_interrupt(int irq, FAR void *context) { register FAR struct enc_driver_s *priv = &g_encx24j600[0]; /* In complex environments, we cannot do SPI transfers from the interrupt * handler because semaphores are probably used to lock the SPI bus. In * this case, we will defer processing to the worker thread. This is also * much kinder in the use of system resources and is, therefore, probably * a good thing to do in any event. */ DEBUGASSERT(work_available(&priv->irqwork)); /* Notice that further GPIO interrupts are disabled until the work is * actually performed. This is to prevent overrun of the worker thread. * Interrupts are re-enabled in enc_irqworker() when the work is completed. */ priv->lower->disable(priv->lower); return work_queue(HPWORK, &priv->irqwork, enc_irqworker, (FAR void *)priv, 0); } /**************************************************************************** * Function: enc_toworker * * Description: * Our TX watchdog timed out. This is the worker thread continuation of * the watchdog timer interrupt. Reset the hardware and start again. * * Parameters: * arg - The reference to the driver structure (case to void*) * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_toworker(FAR void *arg) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)arg; uip_lock_t lock; int ret; nlldbg("Tx timeout\n"); DEBUGASSERT(priv); /* Get exclusive access to uIP. */ lock = uip_lock(); /* Increment statistics and dump debug info */ #ifdef CONFIG_ENCX24J600_STATS priv->stats.txtimeouts++; #endif /* Then reset the hardware: Take the interface down, then bring it * back up */ ret = enc_ifdown(&priv->dev); DEBUGASSERT(ret == OK); ret = enc_ifup(&priv->dev); DEBUGASSERT(ret == OK); (void)ret; /* Then poll uIP for new XMIT data */ (void)uip_poll(&priv->dev, enc_uiptxpoll); /* Release uIP */ uip_unlock(lock); } /**************************************************************************** * Function: enc_txtimeout * * Description: * Our TX watchdog timed out. Called from the timer interrupt handler. * The last TX never completed. Perform work on the worker thread. * * Parameters: * argc - The number of available arguments * arg - The first argument * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_txtimeout(int argc, uint32_t arg, ...) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)arg; int ret; /* In complex environments, we cannot do SPI transfers from the timout * handler because semaphores are probably used to lock the SPI bus. In * this case, we will defer processing to the worker thread. This is also * much kinder in the use of system resources and is, therefore, probably * a good thing to do in any event. */ DEBUGASSERT(priv && work_available(&priv->towork)); /* Notice that Tx timeout watchdog is not active so further Tx timeouts * can occur until we restart the Tx timeout watchdog. */ ret = work_queue(HPWORK, &priv->towork, enc_toworker, (FAR void *)priv, 0); (void)ret; DEBUGASSERT(ret == OK); } /**************************************************************************** * Function: enc_pollworker * * Description: * Periodic timer handler continuation. * * Parameters: * argc - The number of available arguments * arg - The first argument * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_pollworker(FAR void *arg) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)arg; uip_lock_t lock; DEBUGASSERT(priv); /* Get exclusive access to both uIP and the SPI bus. */ lock = uip_lock(); enc_lock(priv); /* Verify that the hardware is ready to send another packet. The driver * start a transmission process by setting ECON1.TXRTS. When the packet is * finished transmitting or is aborted due to an error/cancellation, the * ECON1.TXRTS bit will be cleared. */ if ((enc_rdreg(priv, ENC_ECON1) & ECON1_TXRTS) == 0) { /* Yes.. update TCP timing states and poll uIP for new XMIT data. Hmmm.. * looks like a bug here to me. Does this mean if there is a transmit * in progress, we will missing TCP time state updates? */ (void)uip_timer(&priv->dev, enc_uiptxpoll, ENC_POLLHSEC); } /* Release lock on the SPI bus and uIP */ enc_unlock(priv); uip_unlock(lock); /* Setup the watchdog poll timer again */ (void)wd_start(priv->txpoll, ENC_WDDELAY, enc_polltimer, 1, arg); } /**************************************************************************** * Function: enc_polltimer * * Description: * Periodic timer handler. Called from the timer interrupt handler. * * Parameters: * argc - The number of available arguments * arg - The first argument * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_polltimer(int argc, uint32_t arg, ...) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)arg; int ret; /* In complex environments, we cannot do SPI transfers from the timout * handler because semaphores are probably used to lock the SPI bus. In * this case, we will defer processing to the worker thread. This is also * much kinder in the use of system resources and is, therefore, probably * a good thing to do in any event. */ DEBUGASSERT(priv && work_available(&priv->pollwork)); /* Notice that poll watchdog is not active so further poll timeouts can * occur until we restart the poll timeout watchdog. */ ret = work_queue(HPWORK, &priv->pollwork, enc_pollworker, (FAR void *)priv, 0); (void)ret; DEBUGASSERT(ret == OK); } /**************************************************************************** * Function: enc_ifup * * Description: * NuttX Callback: Bring up the Ethernet interface when an IP address is * provided * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static int enc_ifup(struct uip_driver_s *dev) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; int ret; nlldbg("Bringing up: %d.%d.%d.%d\n", dev->d_ipaddr & 0xff, (dev->d_ipaddr >> 8) & 0xff, (dev->d_ipaddr >> 16) & 0xff, dev->d_ipaddr >> 24 ); /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Initialize Ethernet interface, set the MAC address, and make sure that * the ENC28J80 is not in power save mode. */ ret = enc_reset(priv); if (ret == OK) { enc_setmacaddr(priv); /* Enable interrupts at the ENCX24J600. Interrupts are still disabled * at the interrupt controller. */ enc_bfc(priv, ENC_EIR, EIR_ALLINTS); enc_bfs(priv, ENC_EIE, EIE_INTIE | EIE_LINKIE | EIE_PKTIE | EIE_RXABTIE | EIE_TXIE ); #ifdef CONFIG_ENCX24J600_STATS enc_bfs(priv, ENC_EIE, EIE_TXABTIE); #endif /* Enable the receiver */ enc_bfs(priv, ENC_ECON1, ECON1_RXEN); /* Set and activate a timer process */ (void)wd_start(priv->txpoll, ENC_WDDELAY, enc_polltimer, 1, (uint32_t)priv); /* Mark the interface up and enable the Ethernet interrupt at the * controller */ priv->ifstate = ENCSTATE_UP; priv->lower->enable(priv->lower); } /* Un-lock the SPI bus */ enc_unlock(priv); return ret; } /**************************************************************************** * Function: enc_ifdown * * Description: * NuttX Callback: Stop the interface. * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static int enc_ifdown(struct uip_driver_s *dev) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; irqstate_t flags; int ret; nlldbg("Taking down: %d.%d.%d.%d\n", dev->d_ipaddr & 0xff, (dev->d_ipaddr >> 8) & 0xff, (dev->d_ipaddr >> 16) & 0xff, dev->d_ipaddr >> 24 ); /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Disable the Ethernet interrupt */ flags = irqsave(); priv->lower->disable(priv->lower); /* Cancel the TX poll timer and TX timeout timers */ wd_cancel(priv->txpoll); wd_cancel(priv->txtimeout); /* Reset the device and leave in the power save state */ ret = enc_reset(priv); enc_pwrsave(priv); priv->ifstate = ENCSTATE_DOWN; irqrestore(flags); /* Un-lock the SPI bus */ enc_unlock(priv); return ret; } /**************************************************************************** * Function: enc_txavail * * Description: * Driver callback invoked when new TX data is available. This is a * stimulus perform an out-of-cycle poll and, thereby, reduce the TX * latency. * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * Called in normal user mode * ****************************************************************************/ static int enc_txavail(struct uip_driver_s *dev) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; irqstate_t flags; /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Ignore the notification if the interface is not yet up */ flags = irqsave(); if (priv->ifstate == ENCSTATE_RUNNING) { /* Check if the hardware is ready to send another packet. The driver * starts a transmission process by setting ECON1.TXRTS. When the packet is * finished transmitting or is aborted due to an error/cancellation, the * ECON1.TXRTS bit will be cleared. */ if ((enc_rdreg(priv, ENC_ECON1) & ECON1_TXRTS) == 0) { /* The interface is up and TX is idle; poll uIP for new XMIT data */ (void)uip_poll(&priv->dev, enc_uiptxpoll); } } /* Un-lock the SPI bus */ irqrestore(flags); enc_unlock(priv); return OK; } /**************************************************************************** * Function: enc_rxavail * * Description: * Driver callback invoked when new TX data is available. This is a * stimulus perform an out-of-cycle poll and, thereby, reduce the TX * latency. * * Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * Called in normal user mode * ****************************************************************************/ static int enc_rxavail(struct uip_driver_s *dev) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; if (!sq_empty(&priv->rxqueue)) { nllvdbg("RX queue not empty, trying to dispatch\n"); enc_rxdispatch(priv); } return OK; } /**************************************************************************** * Function: enc_addmac * * Description: * NuttX Callback: Add the specified MAC address to the hardware multicast * address filtering * * Parameters: * dev - Reference to the NuttX driver state structure * mac - The MAC address to be added * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #ifdef CONFIG_NET_IGMP static int enc_addmac(struct uip_driver_s *dev, FAR const uint8_t *mac) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Add the MAC address to the hardware multicast routing table */ #warning "Multicast MAC support not implemented" /* Un-lock the SPI bus */ enc_unlock(priv); return OK; } #endif /**************************************************************************** * Function: enc_rmmac * * Description: * NuttX Callback: Remove the specified MAC address from the hardware multicast * address filtering * * Parameters: * dev - Reference to the NuttX driver state structure * mac - The MAC address to be removed * * Returned Value: * None * * Assumptions: * ****************************************************************************/ #ifdef CONFIG_NET_IGMP static int enc_rmmac(struct uip_driver_s *dev, FAR const uint8_t *mac) { FAR struct enc_driver_s *priv = (FAR struct enc_driver_s *)dev->d_private; /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Add the MAC address to the hardware multicast routing table */ #warning "Multicast MAC support not implemented" /* Un-lock the SPI bus */ enc_unlock(priv); return OK; } #endif /**************************************************************************** * Function: enc_pwrsave * * Description: * The ENCX24J600 may be placed in Power-Down mode through the command * interface. In this mode, the device will no longer be able to transmit or * receive any packets or perform DMA operations. However, most registers, and * all buffer memories, retain their states and remain accessible by the host * controller. The clock driver also remains operational, leaving the CLKOUT * function unaffected. However, the MAC/MII and PHY registers all become * inaccessible, and the PHY registers lose their current states. * * 1. Turn off the Modular Exponentiation and AES engines by clearing * CRYPTEN (EIR<15>). * 2. Turn off packet reception by clearing RXEN (ECON1<0>). * 3. Wait for any in-progress receptions to complete by polling * RXBUSY (ESTAT<13>) until it is clear. * 4. Wait for any current transmission operation to complete by verifying * that TXRTS (ECON1<1>) is clear. * 5. Power-down the PHY by setting the PSLEEP bit (PHCON1<11>). * 6. Power-down the Ethernet interface by clearing * ETHEN and STRCH (ECON2<15,14>). Disabling the LED stretching behavior is * necessary to ensure no LEDs get trapped in a perpetually illuminated * state in the event they are being stretched on when ETHEN is cleared. * * Note: * Instead of providing a powerup function, the job is done by enc_reset. * enc_ifup calls it anyway. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_pwrsave(FAR struct enc_driver_s *priv) { uint16_t regval; nllvdbg("Set PWRSV\n"); /* 1. Turn off AES */ enc_bfc(priv, ENC_EIR, EIR_CRYPTEN); /* 2. Turn off packet reception */ enc_bfc(priv, ENC_ECON1, ECON1_RXEN); /* 3. Wait for pending reception to complete */ enc_waitreg(priv, ENC_ESTAT, ESTAT_RXBUSY, 0); /* 4. Wait for any current transmissions to complete */ enc_waitreg(priv, ENC_ECON1, ECON1_TXRTS, 0); /* 5. Power down the PHY */ regval = enc_rdphy(priv, ENC_PHCON1); regval |= PHCON1_PSLEEP; enc_wrphy(priv, ENC_PHCON1, regval); /* 6. Power down the Ethernet interface */ enc_bfc(priv, ENC_ECON2, ECON2_ETHEN | ECON2_STRCH); } /**************************************************************************** * Function: enc_ldmacaddr * * Description: * Load the MAC address from the ENCX24j600 and write it to the device * structure. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_ldmacaddr(FAR struct enc_driver_s *priv) { uint16_t regval; uint8_t *mac = priv->dev.d_mac.ether_addr_octet; nvdbg("Using ENCX24J600's built in MAC address\n"); regval = enc_rdreg(priv, ENC_MAADR1); mac[0] = regval & 0xff; mac[1] = regval >> 8; regval = enc_rdreg(priv, ENC_MAADR2); mac[2] = regval & 0xff; mac[3] = regval >> 8; regval = enc_rdreg(priv, ENC_MAADR3); mac[4] = regval & 0xff; mac[5] = regval >> 8; } /**************************************************************************** * Function: enc_setmacaddr * * Description: * Set the MAC address to the configured value. This is done after ifup * or after a TX timeout. Note that this means that the interface must * be down before configuring the MAC addr. * If the MAC address is 0 in all digits, the ENCX24J600's MAC is read out. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_setmacaddr(FAR struct enc_driver_s *priv) { uint8_t *mac = priv->dev.d_mac.ether_addr_octet; struct ether_addr zmac; memset(&zmac, 0, sizeof(zmac)); if (memcmp(&priv->dev.d_mac, &zmac, sizeof(zmac)) == 0) { /* No user defined MAC address. Read it from the device. */ enc_ldmacaddr(priv); } else { /* There is a user defined mac address. Write it to the ENCXJ600 */ nvdbg("Using an user defined MAC address\n"); enc_wrreg(priv, ENC_MAADR1, (uint16_t)mac[1] << 8 | (uint16_t)mac[0]); enc_wrreg(priv, ENC_MAADR2, (uint16_t)mac[3] << 8 | (uint16_t)mac[2]); enc_wrreg(priv, ENC_MAADR3, (uint16_t)mac[5] << 8 | (uint16_t)mac[4]); } } /**************************************************************************** * Function: enc_resetbuffers * * Description: * Initializes the RX/TX queues and configures the enc's RX/TX buffers. * Called on general reset and on rxabt interrupt. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static void enc_resetbuffers(FAR struct enc_driver_s *priv) { int i; /* Initialize receive and transmit buffers */ priv->nextpkt = PKTMEM_RX_START; enc_wrreg(priv, ENC_ERXST, PKTMEM_RX_START); /* Program the Tail Pointer, ERXTAIL, to the last even address of the buffer */ enc_wrreg(priv, ENC_ERXTAIL, PKTMEM_RX_END - 2); sq_init(&priv->txfreedescr); sq_init(&priv->rxfreedescr); sq_init(&priv->txqueue); sq_init(&priv->rxqueue); /* For transmition we preinitialize the descriptors to aligned NET_BUFFSIZE */ for (i = 0; i < ENC_NTXDESCR; i++) { priv->txdescralloc[i].addr = PKTMEM_START + PKTMEM_ALIGNED_BUFSIZE * i; sq_addlast((sq_entry_t*)&priv->txdescralloc[i], &priv->txfreedescr); } /* Receive descriptors addresses are set on reception */ for (i = 0; i < CONFIG_ENCX24J600_NRXDESCR; i++) { sq_addlast((sq_entry_t*)&priv->rxdescralloc[i], &priv->rxfreedescr); } } /**************************************************************************** * Function: enc_reset * * Description: * Stop, reset, re-initialize, and restart the ENCX24J600. This is done * initially, on ifup, and after a TX timeout. * * Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * ****************************************************************************/ static int enc_reset(FAR struct enc_driver_s *priv) { int ret; uint16_t regval; nllvdbg("Reset\n"); do { enc_wrreg(priv, ENC_EUDAST, 0x1234); } while (enc_rdreg(priv, ENC_EUDAST) != 0x1234); /* Wait for clock to become ready */ ret = enc_waitreg(priv, ENC_ESTAT, ESTAT_CLKRDY, ESTAT_CLKRDY); if (ret != OK) { nlldbg("ERROR: encx24j600 clock failed to become ready\n"); return -ENODEV; } /* Reset the ENCX24J600 */ enc_setethrst(priv); /* Check if EUDAST has been reset to 0 */ regval = enc_rdreg(priv, ENC_EUDAST); if (regval != 0x0000) { nlldbg("ERROR: encx24j600 seems not to be reset properly\n"); return -ENODEV; } /** * Wait at least 256 μs for the PHY registers and PHY status bits to become * available. */ up_udelay(256); /* Initialize RX/TX buffers */ enc_resetbuffers(priv); #if 0 /* When restarting auto-negotiation, the ESTAT_PHYLINK gets set but the link * seems not to be ready. Because auto-negotiation is enabled by default * (but with different PHANA_* settings) I did not investigate that further. */ /* "Typically, when using auto-negotiation, users should write 0x05E1 to PHANA * to advertise flow control capability." */ enc_wrphy(priv, ENC_PHANA, PHANA_ADPAUS0 | PHANA_AD10FD | PHANA_AD10 | PHANA_AD100FD | PHANA_AD100 | PHANA_ADIEEE0); /* Restart auto-negotiation */ enc_wrphy(priv, ENC_PHCON1, PHCON1_RENEG); do { regval = enc_rdphy(priv, ENC_PHSTAT1); } while ((regval & PHSTAT1_ANDONE) != 0); nllvdbg("Auto-negotation completed\n"); #endif enc_linkstatus(priv); /* Set the maximum packet size which the controller will accept */ enc_wrreg(priv, ENC_MAMXFL, CONFIG_NET_BUFSIZE + 4); ret = enc_waitreg(priv, ENC_ESTAT, ESTAT_PHYLNK, ESTAT_PHYLNK); if (ret == OK) { enc_linkstatus(priv); } #if 0 if (ret != OK) { nlldbg("ERROR: encx24j600 failed to establish link\n"); return -ENODEV; } #endif return OK; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Function: enc_initialize * * Description: * Initialize the Ethernet driver. The ENCX24J600 device is assumed to be * in the post-reset state upon entry to this function. * * Parameters: * spi - A reference to the platform's SPI driver for the ENCX24J600 * lower - The MCU-specific interrupt used to control low-level MCU * functions (i.e., ENCX24J600 GPIO interrupts). * devno - If more than one ENCX24J600 is supported, then this is the * zero based number that identifies the ENCX24J600; * * Returned Value: * OK on success; Negated errno on failure. * * Assumptions: * ****************************************************************************/ int enc_initialize(FAR struct spi_dev_s *spi, FAR const struct enc_lower_s *lower, unsigned int devno) { FAR struct enc_driver_s *priv; DEBUGASSERT(devno < CONFIG_ENCX24J600_NINTERFACES); priv = &g_encx24j600[devno]; /* Initialize the driver structure */ memset(g_encx24j600, 0, CONFIG_ENCX24J600_NINTERFACES*sizeof(struct enc_driver_s)); priv->dev.d_ifup = enc_ifup; /* I/F up (new IP address) callback */ priv->dev.d_ifdown = enc_ifdown; /* I/F down callback */ priv->dev.d_txavail = enc_txavail; /* New TX data callback */ priv->dev.d_rxavail = enc_rxavail; /* RX wating callback */ #ifdef CONFIG_NET_IGMP priv->dev.d_addmac = enc_addmac; /* Add multicast MAC address */ priv->dev.d_rmmac = enc_rmmac; /* Remove multicast MAC address */ #endif priv->dev.d_private = priv; /* Used to recover private state from dev */ /* Create a watchdog for timing polling for and timing of transmisstions */ priv->txpoll = wd_create(); /* Create periodic poll timer */ priv->txtimeout = wd_create(); /* Create TX timeout timer */ priv->spi = spi; /* Save the SPI instance */ priv->lower = lower; /* Save the low-level MCU interface */ /* The interface should be in the down state. However, this function is called * too early in initalization to perform the ENCX24J600 reset in enc_ifdown. We * are depending upon the fact that the application level logic will call enc_ifdown * later to reset the ENCX24J600. */ priv->ifstate = ENCSTATE_UNINIT; /* Attach the interrupt to the driver (but don't enable it yet) */ if (lower->attach(lower, enc_interrupt)) { /* We could not attach the ISR to the interrupt */ return -EAGAIN; } /* Configure SPI for the ENCX24J600 */ enc_configspi(priv->spi); /* Lock the SPI bus so that we have exclusive access */ enc_lock(priv); /* Load the MAC address */ enc_ldmacaddr(priv); /* Power down the device */ enc_pwrsave(priv); /* Unlock the SPI bus */ enc_unlock(priv); /* Register the device with the OS so that socket IOCTLs can be performed */ return netdev_register(&priv->dev); } /**************************************************************************** * Function: enc_stats * * Description: * Return accumulated ENCX24J600 statistics. Statistics are cleared after * being returned. * * Parameters: * devno - If more than one ENCX24J600 is supported, then this is the * zero based number that identifies the ENCX24J600; * stats - The user-provided location to return the statistics. * * Returned Value: * OK on success; Negated errno on failure. * * Assumptions: * ****************************************************************************/ #ifdef CONFIG_ENCX24J600_STATS int enc_stats(unsigned int devno, struct enc_stats_s *stats) { FAR struct enc_driver_s *priv ; irqstate_t flags; DEBUGASSERT(devno < CONFIG_ENCX24J600_NINTERFACES); priv = &g_encx24j600[devno]; /* Disable the Ethernet interrupt */ flags = irqsave(); memcpy(stats, &priv->stats, sizeof(struct enc_stats_s)); memset(&priv->stats, 0, sizeof(struct enc_stats_s)); irqrestore(flags); return OK; } #endif #endif /* CONFIG_NET && CONFIG_ENCX24J600_NET */