diff options
Diffstat (limited to 'src/drivers/mkblctrl/mkblctrl.cpp')
-rw-r--r-- | src/drivers/mkblctrl/mkblctrl.cpp | 125 |
1 files changed, 95 insertions, 30 deletions
diff --git a/src/drivers/mkblctrl/mkblctrl.cpp b/src/drivers/mkblctrl/mkblctrl.cpp index c67276f8a..d0a0829b0 100644 --- a/src/drivers/mkblctrl/mkblctrl.cpp +++ b/src/drivers/mkblctrl/mkblctrl.cpp @@ -74,6 +74,7 @@ #include <uORB/topics/actuator_controls.h> #include <uORB/topics/actuator_controls_effective.h> #include <uORB/topics/actuator_outputs.h> +#include <uORB/topics/esc_status.h> #include <systemlib/err.h> @@ -87,7 +88,7 @@ #define MOTOR_STATE_PRESENT_MASK 0x80 #define MOTOR_STATE_ERROR_MASK 0x7F #define MOTOR_SPINUP_COUNTER 2500 - +#define ESC_UORB_PUBLISH_DELAY 200 class MK : public device::I2C { @@ -119,6 +120,7 @@ public: int set_pwm_rate(unsigned rate); int set_motor_count(unsigned count); int set_motor_test(bool motortest); + int set_overrideSecurityChecks(bool overrideSecurityChecks); int set_px4mode(int px4mode); int set_frametype(int frametype); unsigned int mk_check_for_blctrl(unsigned int count, bool showOutput); @@ -136,11 +138,15 @@ private: unsigned int _motor; int _px4mode; int _frametype; + orb_advert_t _t_outputs; orb_advert_t _t_actuators_effective; + orb_advert_t _t_esc_status; + unsigned int _num_outputs; bool _primary_pwm_device; bool _motortest; + bool _overrideSecurityChecks; volatile bool _task_should_exit; bool _armed; @@ -214,6 +220,7 @@ struct MotorData_t { unsigned int Version; // the version of the BL (0 = old) unsigned int SetPoint; // written by attitude controller unsigned int SetPointLowerBits; // for higher Resolution of new BLs + float SetPoint_PX4; // Values from PX4 unsigned int State; // 7 bit for I2C error counter, highest bit indicates if motor is present unsigned int ReadMode; // select data to read unsigned short RawPwmValue; // length of PWM pulse @@ -243,8 +250,10 @@ MK::MK(int bus) : _t_armed(-1), _t_outputs(0), _t_actuators_effective(0), + _t_esc_status(0), _num_outputs(0), _motortest(false), + _overrideSecurityChecks(false), _motor(-1), _px4mode(MAPPING_MK), _frametype(FRAME_PLUS), @@ -464,6 +473,13 @@ MK::set_motor_test(bool motortest) return OK; } +int +MK::set_overrideSecurityChecks(bool overrideSecurityChecks) +{ + _overrideSecurityChecks = overrideSecurityChecks; + return OK; +} + short MK::scaling(float val, float inMin, float inMax, float outMin, float outMax) { @@ -506,8 +522,6 @@ MK::task_main() _t_outputs = orb_advertise(_primary_pwm_device ? ORB_ID_VEHICLE_CONTROLS : ORB_ID(actuator_outputs_1), &outputs); - - /* advertise the effective control inputs */ actuator_controls_effective_s controls_effective; memset(&controls_effective, 0, sizeof(controls_effective)); @@ -515,6 +529,12 @@ MK::task_main() _t_actuators_effective = orb_advertise(_primary_pwm_device ? ORB_ID_VEHICLE_ATTITUDE_CONTROLS_EFFECTIVE : ORB_ID(actuator_controls_effective_1), &controls_effective); + /* advertise the blctrl status */ + esc_status_s esc; + memset(&esc, 0, sizeof(esc)); + _t_esc_status = orb_advertise(ORB_ID(esc_status), &esc); + + pollfd fds[2]; fds[0].fd = _t_actuators; @@ -602,9 +622,11 @@ MK::task_main() } } - /* don't go under BLCTRL_MIN_VALUE */ - if (outputs.output[i] < BLCTRL_MIN_VALUE) { - outputs.output[i] = BLCTRL_MIN_VALUE; + if(!_overrideSecurityChecks) { + /* don't go under BLCTRL_MIN_VALUE */ + if (outputs.output[i] < BLCTRL_MIN_VALUE) { + outputs.output[i] = BLCTRL_MIN_VALUE; + } } /* output to BLCtrl's */ @@ -612,7 +634,10 @@ MK::task_main() mk_servo_test(i); } else { - mk_servo_set_value(i, scaling(outputs.output[i], -1.0f, 1.0f, 0, 1024)); // scale the output to 0 - 1024 and sent to output routine + //mk_servo_set_value(i, scaling(outputs.output[i], -1.0f, 1.0f, 0, 1024)); // scale the output to 0 - 1024 and sent to output routine + // 11 Bit + Motor[i].SetPoint_PX4 = outputs.output[i]; + mk_servo_set(i, scaling(outputs.output[i], -1.0f, 1.0f, 0, 2047)); // scale the output to 0 - 2047 and sent to output routine } } @@ -635,8 +660,43 @@ MK::task_main() } + + /* + * Only update esc topic every half second. + */ + + if (hrt_absolute_time() - esc.timestamp > 500000) { + esc.counter++; + esc.timestamp = hrt_absolute_time(); + esc.esc_count = (uint8_t) _num_outputs; + esc.esc_connectiontype = ESC_CONNECTION_TYPE_I2C; + + for (unsigned int i = 0; i < _num_outputs; i++) { + esc.esc[i].esc_address = (uint8_t) BLCTRL_BASE_ADDR + i; + esc.esc[i].esc_vendor = ESC_VENDOR_MIKROKOPTER; + esc.esc[i].esc_version = (uint16_t) Motor[i].Version; + esc.esc[i].esc_voltage = (uint16_t) 0; + esc.esc[i].esc_current = (uint16_t) Motor[i].Current; + esc.esc[i].esc_rpm = (uint16_t) 0; + esc.esc[i].esc_setpoint = (float) Motor[i].SetPoint_PX4; + if (Motor[i].Version == 1) { + // BLCtrl 2.0 (11Bit) + esc.esc[i].esc_setpoint_raw = (uint16_t) (Motor[i].SetPoint<<3) | Motor[i].SetPointLowerBits; + } else { + // BLCtrl < 2.0 (8Bit) + esc.esc[i].esc_setpoint_raw = (uint16_t) Motor[i].SetPoint; + } + esc.esc[i].esc_temperature = (uint16_t) Motor[i].Temperature; + esc.esc[i].esc_state = (uint16_t) Motor[i].State; + esc.esc[i].esc_errorcount = (uint16_t) 0; + } + + orb_publish(ORB_ID(esc_status), _t_esc_status, &esc); + } + } + //::close(_t_esc_status); ::close(_t_actuators); ::close(_t_actuators_effective); ::close(_t_armed); @@ -715,17 +775,17 @@ MK::mk_check_for_blctrl(unsigned int count, bool showOutput) fprintf(stderr, "[mkblctrl] blctrl[%i] : found=%i\tversion=%i\tcurrent=%i\tmaxpwm=%i\ttemperature=%i\n", i, Motor[i].State, Motor[i].Version, Motor[i].Current, Motor[i].MaxPWM, Motor[i].Temperature); } - if (foundMotorCount != 4 && foundMotorCount != 6 && foundMotorCount != 8) { - _task_should_exit = true; + + if(!_overrideSecurityChecks) { + if (foundMotorCount != 4 && foundMotorCount != 6 && foundMotorCount != 8) { + _task_should_exit = true; + } } } return foundMotorCount; } - - - int MK::mk_servo_set(unsigned int chan, short val) { @@ -738,17 +798,15 @@ MK::mk_servo_set(unsigned int chan, short val) tmpVal = val; - if (tmpVal > 1024) { - tmpVal = 1024; + if (tmpVal > 2047) { + tmpVal = 2047; } else if (tmpVal < 0) { tmpVal = 0; } - Motor[chan].SetPoint = (uint8_t)(tmpVal / 4); - //Motor[chan].SetPointLowerBits = (uint8_t) tmpVal % 4; - - Motor[chan].SetPointLowerBits = 0; + Motor[chan].SetPoint = (uint8_t)(tmpVal>>3)&0xff; + Motor[chan].SetPointLowerBits = ((uint8_t)tmpVal%8)&0x07; if (_armed == false) { Motor[chan].SetPoint = 0; @@ -1014,8 +1072,7 @@ MK::pwm_ioctl(file *filp, int cmd, unsigned long arg) case PWM_SERVO_SET(0) ... PWM_SERVO_SET(_max_actuators - 1): if (arg < 2150) { Motor[cmd - PWM_SERVO_SET(0)].RawPwmValue = (unsigned short)arg; - mk_servo_set_value(cmd - PWM_SERVO_SET(0), scaling(arg, 1010, 2100, 0, 1024)); - + mk_servo_set(cmd - PWM_SERVO_SET(0), scaling(arg, 1010, 2100, 0, 2047)); } else { ret = -EINVAL; } @@ -1112,25 +1169,19 @@ ssize_t MK::write(file *filp, const char *buffer, size_t len) { unsigned count = len / 2; - // loeschen uint16_t values[4]; uint16_t values[8]; - // loeschen if (count > 4) { - // loeschen // we only have 4 PWM outputs on the FMU - // loeschen count = 4; - // loeschen } if (count > _num_outputs) { // we only have 8 I2C outputs in the driver count = _num_outputs; } - // allow for misaligned values memcpy(values, buffer, count * 2); for (uint8_t i = 0; i < count; i++) { Motor[i].RawPwmValue = (unsigned short)values[i]; - mk_servo_set_value(i, scaling(values[i], 1010, 2100, 0, 1024)); + mk_servo_set(i, scaling(values[i], 1010, 2100, 0, 2047)); } return count * 2; @@ -1282,7 +1333,7 @@ enum FrameType { PortMode g_port_mode; int -mk_new_mode(PortMode new_mode, int update_rate, int motorcount, bool motortest, int px4mode, int frametype) +mk_new_mode(PortMode new_mode, int update_rate, int motorcount, bool motortest, int px4mode, int frametype, bool overrideSecurityChecks) { uint32_t gpio_bits; int shouldStop = 0; @@ -1341,6 +1392,9 @@ mk_new_mode(PortMode new_mode, int update_rate, int motorcount, bool motortest, /* motortest if enabled */ g_mk->set_motor_test(motortest); + /* ovveride security checks if enabled */ + g_mk->set_overrideSecurityChecks(overrideSecurityChecks); + /* count used motors */ do { @@ -1406,6 +1460,7 @@ mkblctrl_main(int argc, char *argv[]) int px4mode = MAPPING_PX4; int frametype = FRAME_PLUS; // + plus is default bool motortest = false; + bool overrideSecurityChecks = false; bool showHelp = false; bool newMode = false; @@ -1461,11 +1516,21 @@ mkblctrl_main(int argc, char *argv[]) showHelp = true; } + /* look for the optional --override-security-checks parameter */ + if (strcmp(argv[i], "--override-security-checks") == 0) { + overrideSecurityChecks = true; + newMode = true; + } + } if (showHelp) { fprintf(stderr, "mkblctrl: help:\n"); - fprintf(stderr, " [-mkmode frame{+/x}] [-b i2c_bus_number] [-t motortest] [-h / --help]\n"); + fprintf(stderr, " [-mkmode frame{+/x}] [-b i2c_bus_number] [-t motortest] [--override-security-checks] [-h / --help]\n\n"); + fprintf(stderr, "\t -mkmode frame {+/x} \t\t Type of frame, if Mikrokopter motor order is used.\n"); + fprintf(stderr, "\t -b i2c_bus_number \t\t Set the i2c bus where the ESCs are connected to (default 1).\n"); + fprintf(stderr, "\t -t motortest \t\t\t Spin up once every motor in order of motoraddress. (DANGER !!!)\n"); + fprintf(stderr, "\t --override-security-checks \t\t Disable all security checks (arming and number of ESCs). Used to test single Motors etc. (DANGER !!!)\n"); exit(1); } @@ -1483,7 +1548,7 @@ mkblctrl_main(int argc, char *argv[]) /* parameter set ? */ if (newMode) { /* switch parameter */ - return mk_new_mode(port_mode, pwm_update_rate_in_hz, motorcount, motortest, px4mode, frametype); + return mk_new_mode(port_mode, pwm_update_rate_in_hz, motorcount, motortest, px4mode, frametype, overrideSecurityChecks); } /* test, etc. here g*/ |