/**************************************************************************** * drivers/wireless/cc1101/ISM1_868MHzGFSK100kbps.c * * Copyright (C) 2011 Uros Platise. All rights reserved. * Copyright (C) 2011 Ales Verbic. All rights reserved. * * Authors: Uros Platise * Ales Verbic * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #include /** Settings for 868 MHz, GFSK at 100kbps * * ISM Region 1 (Europe) only, Band 868–870 MHz * * Frequency ERP Duty Cycle Bandwidth Remarks * 868 – 868.6 MHz +14 dBm < 1% No limits * 868.7 – 869.2 MHz +14 dBm < 0.1% No limits * 869.3 – 869.4 MHz +10 dBm No limits < 25 kHz Appropriate access protocol required * 869.4 – 869.65 MHz +27 dBm < 10% < 25 kHz Channels may be combined to one high speed channel * 869.7 -870 MHz +7 dBm No limits No limits * * Deviation = 46.142578 * Base frequency = 867.999985 * Carrier frequency = 867.999985 * Channel number = 0 * Carrier frequency = 867.999985 * Modulated = true * Modulation format = GFSK * Manchester enable = false * Sync word qualifier mode = 30/32 sync word bits detected * Preamble count = 4 * Channel spacing = 199.813843 * Carrier frequency = 867.999985 * Data rate = 99.9069 * RX filter BW = 210.937500 * Data format = Normal mode * Length config = Fixed packet length mode. Length configured in PKTLEN register * CRC enable = true * Packet length = 62 * Device address = 00 * Address config = NO Address check, no broadcast * CRC autoflush = true * PA ramping = false * TX power = 0 */ const struct c1101_rfsettings_s cc1101_rfsettings_ISM1_868MHzGFSK100kbps = { .FSCTRL1 = 0x08, // FSCTRL1 Frequency Synthesizer Control .FSCTRL0 = 0x00, // FSCTRL0 Frequency Synthesizer Control .FREQ2 = 0x20, // FREQ2 Frequency Control Word, High Byte .FREQ1 = 0x25, // FREQ1 Frequency Control Word, Middle Byte .FREQ0 = 0xED, // FREQ0 Frequency Control Word, Low Byte .MDMCFG4 = 0x8B, // MDMCFG4 Modem Configuration .MDMCFG3 = 0xE5, // MDMCFG3 Modem Configuration .MDMCFG2 = 0x13, // MDMCFG2 Modem Configuration .MDMCFG1 = 0x22, // MDMCFG1 Modem Configuration .MDMCFG0 = 0xE5, // MDMCFG0 Modem Configuration .DEVIATN = 0x46, // DEVIATN Modem Deviation Setting .FOCCFG = 0x1D, // FOCCFG Frequency Offset Compensation Configuration .BSCFG = 0x1C, // BSCFG Bit Synchronization Configuration .AGCCTRL2= 0xC7, // AGCCTRL2 AGC Control .AGCCTRL1= 0x00, // AGCCTRL1 AGC Control .AGCCTRL0= 0xB2, // AGCCTRL0 AGC Control .FREND1 = 0xB6, // FREND1 Front End RX Configuration .FREND0 = 0x10, // FREND0 Front End TX Configuration .FSCAL3 = 0xEA, // FSCAL3 Frequency Synthesizer Calibration .FSCAL2 = 0x2A, // FSCAL2 Frequency Synthesizer Calibration .FSCAL1 = 0x00, // FSCAL1 Frequency Synthesizer Calibration .FSCAL0 = 0x1F, // FSCAL0 Frequency Synthesizer Calibration .CHMIN = 0, // Fix at 9th channel: 869.80 MHz +- 100 kHz RF Bandwidth .CHMAX = 9, // single channel .PAMAX = 8, // 0 means power OFF, 8 represents PA[7] .PA = {0x03, 0x0F, 0x1E, 0x27, 0x67, 0x50, 0x81, 0xC2} };