From 8765c895a02731e26a6eb7f883173db1bf959d34 Mon Sep 17 00:00:00 2001 From: patacongo Date: Fri, 22 Jan 2010 03:08:29 +0000 Subject: Add serial and LED driver git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2519 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/arch/arm/src/sam3u/Make.defs | 4 +- nuttx/arch/arm/src/sam3u/sam3u_lowputc.c | 4 +- nuttx/arch/arm/src/sam3u/sam3u_serial.c | 1450 +++++++++++++++++++++++++ nuttx/arch/arm/src/stm32/stm32_lowputc.c | 4 +- nuttx/arch/arm/src/stm32/stm32_serial.c | 2 +- nuttx/configs/sam3u-ek/include/board.h | 26 +- nuttx/configs/sam3u-ek/ostest/defconfig | 2 +- nuttx/configs/sam3u-ek/src/sam3uek_internal.h | 9 + nuttx/configs/sam3u-ek/src/up_leds.c | 91 +- 9 files changed, 1565 insertions(+), 27 deletions(-) create mode 100755 nuttx/arch/arm/src/sam3u/sam3u_serial.c diff --git a/nuttx/arch/arm/src/sam3u/Make.defs b/nuttx/arch/arm/src/sam3u/Make.defs index b63b9017a..2e7fd965a 100755 --- a/nuttx/arch/arm/src/sam3u/Make.defs +++ b/nuttx/arch/arm/src/sam3u/Make.defs @@ -1,7 +1,7 @@ ############################################################################ # arch/arm/src/sam3u/Make.defs # -# Copyright (C) 2009 Gregory Nutt. All rights reserved. +# Copyright (C) 2009-2010 Gregory Nutt. All rights reserved. # Author: Gregory Nutt # # Redistribution and use in source and binary forms, with or without @@ -46,5 +46,5 @@ CMN_CSRCS = up_allocateheap.c up_assert.c up_blocktask.c up_copystate.c \ CHIP_ASRCS = CHIP_CSRCS = sam3u_clockconfig.c sam3u_irq.c sam3u_lowputc.c sam3u_pio.c \ - sam3u_start.c sam3u_timerisr.c + sam3u_serial.c sam3u_start.c sam3u_timerisr.c diff --git a/nuttx/arch/arm/src/sam3u/sam3u_lowputc.c b/nuttx/arch/arm/src/sam3u/sam3u_lowputc.c index 9f354bc9d..fe5b38aa5 100755 --- a/nuttx/arch/arm/src/sam3u/sam3u_lowputc.c +++ b/nuttx/arch/arm/src/sam3u/sam3u_lowputc.c @@ -304,7 +304,7 @@ void sam3u_lowsetup(void) #endif /* Configure the console (only) */ -#ifdef HAVE_CONSOLE +#if defined(HAVE_CONSOLE) && !defined(CONFIG_SUPPRESS_UART_CONFIG) /* Reset and disable receiver and transmitter */ putreg32((UART_CR_RSTRX|UART_CR_RSTTX|UART_CR_RXDIS|UART_CR_TXDIS), @@ -316,7 +316,7 @@ void sam3u_lowsetup(void) /* Set up the mode register */ - putreg32(MR_VALUE, AM3U_CONSOLE_BASE+SAM3U_UART_MR_OFFSET); + putreg32(MR_VALUE, SAM3U_CONSOLE_BASE+SAM3U_UART_MR_OFFSET); /* Configure the console baud */ diff --git a/nuttx/arch/arm/src/sam3u/sam3u_serial.c b/nuttx/arch/arm/src/sam3u/sam3u_serial.c new file mode 100755 index 000000000..42430d9e1 --- /dev/null +++ b/nuttx/arch/arm/src/sam3u/sam3u_serial.c @@ -0,0 +1,1450 @@ +/**************************************************************************** + * arch/arm/src/sam3u/sam3u_serial.c + * + * Copyright (C) 2010 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "chip.h" +#include "sam3u_uart.h" +#include "up_arch.h" +#include "up_internal.h" +#include "os_internal.h" + +/**************************************************************************** + * Definitions + ****************************************************************************/ + +/* Some sanity checks *******************************************************/ + +/* If the USART is not being used as a UART, then it really isn't enabled + * for our purposes. + */ + +#ifndef CONFIG_USART0_ISUART +# undef CONFIG_SAM3U_USART0 +#endif +#ifndef CONFIG_USART1_ISUART +# undef CONFIG_SAM3U_USART1 +#endif +#ifndef CONFIG_USART2_ISUART +# undef CONFIG_SAM3U_USART2 +#endif +#ifndef CONFIG_USART3_ISUART +# undef CONFIG_SAM3U_USART3 +#endif + +/* Is there a USART/USART enabled? */ + +#if !defined(CONFIG_SAM3U_UART) && !defined(CONFIG_SAM3U_USART0) && \ + !defined(CONFIG_SAM3U_USART1) && !defined(CONFIG_SAM3U_USART2) && \ + !defined(CONFIG_SAM3U_USART3) +# error "No USARTs enabled" +#endif + +#if defined(CONFIG_SAM3U_USART0) || defined(CONFIG_SAM3U_USART1) ||\ + defined(CONFIG_SAM3U_USART2) || defined(CONFIG_SAM3U_USART3) +# define HAVE_USART +#endif + +/* Is there a serial console? */ + +#if defined(CONFIG_UART_SERIAL_CONSOLE) && defined(CONFIG_SAM3U_UART) +# undef CONFIG_USART0_SERIAL_CONSOLE +# undef CONFIG_USART1_SERIAL_CONSOLE +# undef CONFIG_USART2_SERIAL_CONSOLE +# undef CONFIG_USART3_SERIAL_CONSOLE +# define HAVE_CONSOLE 1 +#elif defined(CONFIG_USART0_SERIAL_CONSOLE) && defined(CONFIG_SAM3U_USART0) +# undef CONFIG_UART_SERIAL_CONSOLE +# undef CONFIG_USART1_SERIAL_CONSOLE +# undef CONFIG_USART2_SERIAL_CONSOLE +# undef CONFIG_USART3_SERIAL_CONSOLE +# define HAVE_CONSOLE 1 +#elif defined(CONFIG_USART1_SERIAL_CONSOLE) && defined(CONFIG_SAM3U_USART1) +# undef CONFIG_UART_SERIAL_CONSOLE +# undef CONFIG_USART0_SERIAL_CONSOLE +# undef CONFIG_USART2_SERIAL_CONSOLE +# undef CONFIG_USART3_SERIAL_CONSOLE +# define HAVE_CONSOLE 1 +#elif defined(CONFIG_USART2_SERIAL_CONSOLE) && defined(CONFIG_SAM3U_USART2) +# undef CONFIG_UART_SERIAL_CONSOLE +# undef CONFIG_USART0_SERIAL_CONSOLE +# undef CONFIG_USART1_SERIAL_CONSOLE +# undef CONFIG_USART3_SERIAL_CONSOLE +# define HAVE_CONSOLE 1 +#elif defined(CONFIG_USART3_SERIAL_CONSOLE) && defined(CONFIG_SAM3U_USART3) +# undef CONFIG_UART_SERIAL_CONSOLE +# undef CONFIG_USART0_SERIAL_CONSOLE +# undef CONFIG_USART1_SERIAL_CONSOLE +# undef CONFIG_USART2_SERIAL_CONSOLE +# define HAVE_CONSOLE 1 +#else +# warning "No valid CONFIG_USARTn_SERIAL_CONSOLE Setting" +# undef CONFIG_UART_SERIAL_CONSOLE +# undef CONFIG_USART0_SERIAL_CONSOLE +# undef CONFIG_USART1_SERIAL_CONSOLE +# undef CONFIG_USART2_SERIAL_CONSOLE +# undef CONFIG_USART3_SERIAL_CONSOLE +# undef HAVE_CONSOLE +#endif + +/* If we are not using the serial driver for the console, then we still must + * provide some minimal implementation of up_putc. + */ + +#ifdef CONFIG_USE_SERIALDRIVER + +/* Which UART/USART with be tty0/console and which tty1? tty2? tty3? tty4? */ + +#if defined(CONFIG_UART_SERIAL_CONSOLE) +# define CONSOLE_DEV g_uartport /* UART=console */ +# define TTYS0_DEV g_uartport /* UART=ttyS0 */ +# ifdef CONFIG_SAM3U_USART0 +# define TTYS1_DEV g_usart0port /* UART=ttyS0;USART0=ttyS1 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* UART=ttyS0;USART0=ttyS1;USART1=ttyS2 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* UART=ttyS0;USART0=ttyS1;USART1=ttyS2;USART2=ttyS3 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS4_DEV g_usart3port /* UART=ttyS0;USART0=ttyS1;USART1=ttyS2;USART2=ttyS3;USART3=ttyS4 */ +# else +# undef TTYS4_DEV /* UART=ttyS0;USART0=ttyS1;USART1=ttyS2;USART2=ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* UART=ttyS0;USART0=ttyS1;USART1=ttyS;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* UART=ttyS0;USART0=ttyS1;USART1=ttyS;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* UART=ttyS0;USART0=ttyS1;USART2=ttys2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* UART=ttyS0;USART0=ttyS1;USART2=ttys2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* UART=ttyS0;USART0=ttyS1;USART2=ttys2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* UART=ttyS0;USART0=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* UART=ttyS0;USART0=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS1_DEV g_usart1port /* UART=ttyS0;USART1=ttyS1;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* UART=ttyS0;USART1=ttyS1;USART2=ttyS2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* UART=ttyS0;USART1=ttyS1;USART2=ttyS2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* UART=ttyS0;USART1=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* UART=ttyS0;USART1=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* UART=ttyS0;USART1=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS1_DEV g_usart2port /* UART=ttyS0;USART2=ttyS1;No ttyS3;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* UART=ttyS0;USART2=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* UART=ttyS0;USART2=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS1_DEV g_usart3port /* UART=ttyS0;USART3=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS1_DEV /* UART=ttyS0;No ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS2_DEV /* No ttyS2 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +#elif defined(CONFIG_USART0_SERIAL_CONSOLE) +# define CONSOLE_DEV g_usart0port /* USART0=console */ +# define TTYS0_DEV g_usart0port /* USART0=ttyS0 */ +# ifdef CONFIG_SAM3U_UART +# define TTYS1_DEV g_uartport /* USART0=ttyS0;UART=ttyS1 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* USART0=ttyS0;UART=ttyS1;USART1=ttyS2 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* USART0=ttyS0;UART=ttyS1;USART1=ttyS2;USART2=ttyS3 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS4_DEV g_usart3port /* USART0=ttyS0;UART=ttyS1;USART1=ttyS2;USART2=ttyS3;USART3=ttyS4 */ +# else +# undef TTYS4_DEV /* USART0=ttyS0;UART=ttyS1;USART1=ttyS2;USART2=ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART0=ttyS0;UART=ttyS1;USART1=ttyS;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART0=ttyS0;UART=ttyS1;USART1=ttyS;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART0=ttyS0;UART=ttyS1;USART2=ttys2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART0=ttyS0;UART=ttyS1;USART2=ttys2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART0=ttyS0;UART=ttyS1;USART2=ttys2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART0=ttyS0;UART=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART0=ttyS0;UART=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS1_DEV g_usart1port /* USART0=ttyS0;USART1=ttyS1;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART0=ttyS0;USART1=ttyS1;USART2=ttyS2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART0=ttyS0;USART1=ttyS1;USART2=ttyS2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART0=ttyS0;USART1=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART0=ttyS0;USART1=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART0=ttyS0;USART1=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS1_DEV g_usart2port /* USART0=ttyS0;USART2=ttyS1;No ttyS3;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART0=ttyS0;USART2=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART0=ttyS0;USART2=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS1_DEV g_usart3port /* USART0=ttyS0;USART3=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS1_DEV /* USART0=ttyS0;No ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS2_DEV /* No ttyS2 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +#elif defined(CONFIG_USART1_SERIAL_CONSOLE) +# define CONSOLE_DEV g_usart1port /* USART1=console */ +# define TTYS0_DEV g_usart1port /* USART1=ttyS0 */ +# ifdef CONFIG_SAM3U_UART +# define TTYS1_DEV g_uartport /* USART1=ttyS0;UART=ttyS1 */ +# ifdef CONFIG_SAM3U_USART0 +# define TTYS2_DEV g_usart0port /* USART1=ttyS0;UART=ttyS1;USART0=ttyS2 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* USART1=ttyS0;UART=ttyS1;USART0=ttyS2;USART2=ttyS3 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS4_DEV g_usart3port /* USART1=ttyS0;UART=ttyS1;USART0=ttyS2;USART2=ttyS3;USART3=ttyS4 */ +# else +# undef TTYS4_DEV /* USART1=ttyS0;UART=ttyS1;USART0=ttyS2;USART2=ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART1=ttyS0;UART=ttyS1;USART0=ttyS;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART1=ttyS0;UART=ttyS1;USART0=ttyS;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART1=ttyS0;UART=ttyS1;USART2=ttys2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART1=ttyS0;UART=ttyS1;USART2=ttys2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART1=ttyS0;UART=ttyS1;USART2=ttys2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART1=ttyS0;UART=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART1=ttyS0;UART=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# endif +# else +# ifdef CONFIG_SAM3U_USART0 +# define TTYS1_DEV g_usart0port /* USART1=ttyS0;USART0=ttyS1;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART1=ttyS0;USART0=ttyS1;USART2=ttyS2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART1=ttyS0;USART0=ttyS1;USART2=ttyS2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART1=ttyS0;USART0=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART1=ttyS0;USART0=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART1=ttyS0;USART0=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS1_DEV g_usart2port /* USART1=ttyS0;USART2=ttyS1;No ttyS3;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART1=ttyS0;USART2=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART1=ttyS0;USART2=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS1_DEV g_usart3port /* USART1=ttyS0;USART3=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS1_DEV /* USART1=ttyS0;No ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS2_DEV /* No ttyS2 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +#elif defined(CONFIG_USART2_SERIAL_CONSOLE) +# define CONSOLE_DEV g_usart2port /* USART2=console */ +# define TTYS0_DEV g_usart2port /* USART2=ttyS0 */ +# ifdef CONFIG_SAM3U_UART +# define TTYS1_DEV g_uartport /* USART2=ttyS0;UART=ttyS1 */ +# ifdef CONFIG_SAM3U_USART0 +# define TTYS2_DEV g_usart0port /* USART2=ttyS0;UART=ttyS1;USART0=ttyS2 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS3_DEV g_usart1port /* USART2=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS4_DEV g_usart3port /* USART2=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3;USART3=ttyS4 */ +# else +# undef TTYS4_DEV /* USART2=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART2=ttyS0;UART=ttyS1;USART0=ttyS;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART2=ttyS0;UART=ttyS1;USART0=ttyS;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* USART2=ttyS0;UART=ttyS1;USART1=ttys2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART2=ttyS0;UART=ttyS1;USART1=ttys2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART2=ttyS0;UART=ttyS1;USART1=ttys2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART2=ttyS0;UART=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART2=ttyS0;UART=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# endif +# else +# ifdef CONFIG_SAM3U_USART0 +# define TTYS1_DEV g_usart0port /* USART2=ttyS0;USART0=ttyS1;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* USART2=ttyS0;USART0=ttyS1;USART1=ttyS2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS3_DEV g_usart3port /* USART2=ttyS0;USART0=ttyS1;USART1=ttyS2;USART3=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART2=ttyS0;USART0=ttyS1;USART1=ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART2=ttyS0;USART0=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART2=ttyS0;USART0=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS1_DEV g_usart1port /* USART2=ttyS0;USART1=ttyS1;No ttyS3;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART3 +# define TTYS2_DEV g_usart3port /* USART2=ttyS0;USART1=ttyS1;USART3=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART2=ttyS0;USART1=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART3 +# define TTYS1_DEV g_usart3port /* USART2=ttyS0;USART3=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS1_DEV /* USART2=ttyS0;No ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS2_DEV /* No ttyS2 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +#elif defined(CONFIG_USART3_SERIAL_CONSOLE) +# define CONSOLE_DEV g_usart3port /* USART3=console */ +# define TTYS0_DEV g_usart3port /* USART3=ttyS0 */ +# ifdef CONFIG_SAM3U_UART +# define TTYS1_DEV g_uartport /* USART3=ttyS0;UART=ttyS1 */ +# ifdef CONFIG_SAM3U_USART0 +# define TTYS2_DEV g_usart0port /* USART3=ttyS0;UART=ttyS1;USART0=ttyS2 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS3_DEV g_usart1port /* USART3=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS4_DEV g_usart2port /* USART3=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3;USART2=ttyS4 */ +# else +# undef TTYS4_DEV /* USART3=ttyS0;UART=ttyS1;USART0=ttyS2;USART1=ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* USART3=ttyS0;UART=ttyS1;USART0=ttyS;USART2=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART3=ttyS0;UART=ttyS1;USART0=ttyS;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* USART3=ttyS0;UART=ttyS1;USART1=ttys2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* USART3=ttyS0;UART=ttyS1;USART1=ttys2;USART2=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART3=ttyS0;UART=ttyS1;USART1=ttys2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART3=ttyS0;UART=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART3=ttyS0;UART=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# undef TTYS4_DEV /* No ttyS4 */ +# endif +# endif +# else +# ifdef CONFIG_SAM3U_USART0 +# define TTYS1_DEV g_usart0port /* USART3=ttyS0;USART0=ttyS1;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART1 +# define TTYS2_DEV g_usart1port /* USART3=ttyS0;USART0=ttyS1;USART1=ttyS2;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS3_DEV g_usart2port /* USART3=ttyS0;USART0=ttyS1;USART1=ttyS2;USART2=ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART3=ttyS0;USART0=ttyS1;USART1=ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_usart2port /* USART3=ttyS0;USART0=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS2_DEV /* USART3=ttyS0;USART0=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART1 +# define TTYS1_DEV g_usart1port /* USART3=ttyS0;USART1=ttyS1;No ttyS3;No ttyS4 */ +# ifdef CONFIG_SAM3U_USART2 +# define TTYS2_DEV g_EEEEport /* USART3=ttyS0;USART1=ttyS1;USART2=ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS3_DEV /* USART3=ttyS0;USART1=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# else +# ifdef CONFIG_SAM3U_USART2 +# define TTYS1_DEV g_usart2port /* USART3=ttyS0;USART2=ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# else +# undef TTYS1_DEV /* USART3=ttyS0;No ttyS1;No ttyS2;No ttyS3;No ttyS4 */ +# endif +# undef TTYS2_DEV /* No ttyS2 */ +# endif +# undef TTYS3_DEV /* No ttyS3 */ +# endif +# undef TTYS4_DEV /* No ttyS4 */ +# endif +#endif + +/**************************************************************************** + * Private Types + ****************************************************************************/ + +struct up_dev_s +{ + uint32_t usartbase; /* Base address of USART registers */ + uint32_t baud; /* Configured baud */ + uint32_t imr; /* Saved interrupt mask bits value */ + uint32_t sr; /* Saved status bits */ + uint8_t irq; /* IRQ associated with this USART */ + uint8_t parity; /* 0=none, 1=odd, 2=even */ + uint8_t bits; /* Number of bits (7 or 8) */ + bool stopbits2; /* true: Configure with 2 stop bits instead of 1 */ +}; + +/**************************************************************************** + * Private Function Prototypes + ****************************************************************************/ + +static int up_setup(struct uart_dev_s *dev); +static void up_shutdown(struct uart_dev_s *dev); +static int up_attach(struct uart_dev_s *dev); +static void up_detach(struct uart_dev_s *dev); +static int up_interrupt(int irq, void *context); +static int up_ioctl(struct file *filep, int cmd, unsigned long arg); +static int up_receive(struct uart_dev_s *dev, uint32_t *status); +static void up_rxint(struct uart_dev_s *dev, bool enable); +static bool up_rxavailable(struct uart_dev_s *dev); +static void up_send(struct uart_dev_s *dev, int ch); +static void up_txint(struct uart_dev_s *dev, bool enable); +static bool up_txready(struct uart_dev_s *dev); +static bool up_txempty(struct uart_dev_s *dev); + +/**************************************************************************** + * Private Variables + ****************************************************************************/ + +struct uart_ops_s g_uart_ops = +{ + .setup = up_setup, + .shutdown = up_shutdown, + .attach = up_attach, + .detach = up_detach, + .ioctl = up_ioctl, + .receive = up_receive, + .rxint = up_rxint, + .rxavailable = up_rxavailable, + .send = up_send, + .txint = up_txint, + .txready = up_txready, + .txempty = up_txempty, +}; + +/* I/O buffers */ + +#ifdef CONFIG_SAM3U_UART +static char g_uartrxbuffer[CONFIG_UART_RXBUFSIZE]; +static char g_uarttxbuffer[CONFIG_UART_TXBUFSIZE]; +#endif +#ifdef CONFIG_SAM3U_USART0 +static char g_usart0rxbuffer[CONFIG_USART0_RXBUFSIZE]; +static char g_usart0txbuffer[CONFIG_USART0_TXBUFSIZE]; +#endif +#ifdef CONFIG_SAM3U_USART1 +static char g_usart1rxbuffer[CONFIG_USART1_RXBUFSIZE]; +static char g_usart1txbuffer[CONFIG_USART1_TXBUFSIZE]; +#endif +#ifdef CONFIG_SAM3U_USART2 +static char g_usart2rxbuffer[CONFIG_USART2_RXBUFSIZE]; +static char g_usart2txbuffer[CONFIG_USART2_TXBUFSIZE]; +#endif +#ifdef CONFIG_SAM3U_USART3 +static char g_usart3rxbuffer[CONFIG_USART3_RXBUFSIZE]; +static char g_usart3txbuffer[CONFIG_USART3_TXBUFSIZE]; +#endif + +/* This describes the state of the SAM3U UART port. */ + +#ifdef CONFIG_SAM3U_UART +static struct up_dev_s g_uartpriv = +{ + .usartbase = SAM3U_UART_BASE, + .baud = CONFIG_UART_BAUD, + .irq = SAM3U_IRQ_UART, + .parity = CONFIG_UART_PARITY, + .bits = CONFIG_UART_BITS, + .stopbits2 = CONFIG_UART_2STOP, +}; + +static uart_dev_t g_uartport = +{ + .recv = + { + .size = CONFIG_UART_RXBUFSIZE, + .buffer = g_uartrxbuffer, + }, + .xmit = + { + .size = CONFIG_UART_TXBUFSIZE, + .buffer = g_uarttxbuffer, + }, + .ops = &g_uart_ops, + .priv = &g_uartpriv, +}; +#endif + +/* This describes the state of the SAM3U USART1 ports. */ + +#ifdef CONFIG_SAM3U_USART0 +static struct up_dev_s g_usart0priv = +{ + .usartbase = SAM3U_USART0_BASE, + .baud = CONFIG_USART0_BAUD, + .irq = SAM3U_IRQ_USART0, + .parity = CONFIG_USART0_PARITY, + .bits = CONFIG_USART0_BITS, + .stopbits2 = CONFIG_USART0_2STOP, +}; + +static uart_dev_t g_usart0port = +{ + .recv = + { + .size = CONFIG_USART0_RXBUFSIZE, + .buffer = g_usart0rxbuffer, + }, + .xmit = + { + .size = CONFIG_USART0_TXBUFSIZE, + .buffer = g_usart0txbuffer, + }, + .ops = &g_uart_ops, + .priv = &g_usart0priv, +}; +#endif + +/* This describes the state of the SAM3U USART1 ports. */ + +#ifdef CONFIG_SAM3U_USART1 +static struct up_dev_s g_usart1priv = +{ + .usartbase = SAM3U_USART1_BASE, + .baud = CONFIG_USART1_BAUD, + .irq = SAM3U_IRQ_USART1, + .parity = CONFIG_USART1_PARITY, + .bits = CONFIG_USART1_BITS, + .stopbits2 = CONFIG_USART1_2STOP, +}; + +static uart_dev_t g_usart1port = +{ + .recv = + { + .size = CONFIG_USART1_RXBUFSIZE, + .buffer = g_usart1rxbuffer, + }, + .xmit = + { + .size = CONFIG_USART1_TXBUFSIZE, + .buffer = g_usart1txbuffer, + }, + .ops = &g_uart_ops, + .priv = &g_usart1priv, +}; +#endif + +/* This describes the state of the SAM3U USART2 port. */ + +#ifdef CONFIG_SAM3U_USART2 +static struct up_dev_s g_usart2priv = +{ + .usartbase = SAM3U_USART2_BASE, + .baud = CONFIG_USART2_BAUD, + .irq = SAM3U_IRQ_USART2, + .parity = CONFIG_USART2_PARITY, + .bits = CONFIG_USART2_BITS, + .stopbits2 = CONFIG_USART2_2STOP, +}; + +static uart_dev_t g_usart2port = +{ + .recv = + { + .size = CONFIG_USART2_RXBUFSIZE, + .buffer = g_usart2rxbuffer, + }, + .xmit = + { + .size = CONFIG_USART2_TXBUFSIZE, + .buffer = g_usart2txbuffer, + }, + .ops = &g_uart_ops, + .priv = &g_usart2priv, +}; +#endif + +/* This describes the state of the SAM3U USART3 port. */ + +#ifdef CONFIG_SAM3U_USART3 +static struct up_dev_s g_usart3priv = +{ + .usartbase = SAM3U_USART3_BASE, + .baud = CONFIG_USART3_BAUD, + .irq = SAM3U_IRQ_USART3, + .parity = CONFIG_USART3_PARITY, + .bits = CONFIG_USART3_BITS, + .stopbits2 = CONFIG_USART3_2STOP, +}; + +static uart_dev_t g_usart3port = +{ + .recv = + { + .size = CONFIG_USART3_RXBUFSIZE, + .buffer = g_usart3rxbuffer, + }, + .xmit = + { + .size = CONFIG_USART3_TXBUFSIZE, + .buffer = g_usart3txbuffer, + }, + .ops = &g_uart_ops, + .priv = &g_usart3priv, +}; +#endif + +/**************************************************************************** + * Private Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: up_serialin + ****************************************************************************/ + +static inline uint32_t up_serialin(struct up_dev_s *priv, int offset) +{ + return getreg32(priv->usartbase + offset); +} + +/**************************************************************************** + * Name: up_serialout + ****************************************************************************/ + +static inline void up_serialout(struct up_dev_s *priv, int offset, uint32_t value) +{ + putreg32(value, priv->usartbase + offset); +} + +/**************************************************************************** + * Name: up_enableint + ****************************************************************************/ + +static inline void up_enableint(struct up_dev_s *priv) +{ + up_serialout(priv, SAM3U_UART_IER_OFFSET, priv->imr); +} + +/**************************************************************************** + * Name: up_disableint + ****************************************************************************/ + +static inline void up_disableint(struct up_dev_s *priv) +{ + up_serialout(priv, SAM3U_UART_IDR_OFFSET, ~priv->imr); +} + +/**************************************************************************** + * Name: up_restoreusartint + ****************************************************************************/ + +static void up_restoreusartint(struct up_dev_s *priv, uint32_t imr) +{ + /* Save the interrupt mask */ + + priv->imr = imr; + + /* And restore the interrupt state */ + + up_serialout(priv, SAM3U_UART_IDR_OFFSET, ~imr); + up_serialout(priv, SAM3U_UART_IER_OFFSET, imr); +} + +/**************************************************************************** + * Name: up_disableallints + ****************************************************************************/ + +static void up_disableallints(struct up_dev_s *priv, uint32_t *imr) +{ + if (imr) + { + /* Return the current interrupt mask */ + + *imr = priv->imr; + } + + /* Disable all interrupts */ + + up_restoreusartint(priv, 0); +} + +/**************************************************************************** + * Name: up_setup + * + * Description: + * Configure the USART baud, bits, parity, etc. This method is called the + * first time that the serial port is opened. + * + ****************************************************************************/ + +static int up_setup(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; +#ifndef CONFIG_SUPPRESS_UART_CONFIG + uint32_t regval; + + /* Note: The logic here depends on the fact that that the USART module + * was enabled and the pins were configured in sam3u_lowsetup(). + */ + + /* The shutdown method will put the UART in a known, disabled state */ + + up_shutdown(dev); + + /* Set up the mode register. Start with normal UART mode and the MCK + * as the timing source + */ + + regval = (USART_MR_MODE_NORMAL|USART_MR_USCLKS_MCK); + + /* OR in settings for the selected number of bits */ + + if (priv->bits == 5) + { + regval |= USART_MR_CHRL_5BITS; /* 5 bits */ + } + else if (priv->bits == 6) + { + regval |= USART_MR_CHRL_6BITS; /* 6 bits */ + } + else if (priv->bits == 7) + { + regval |= USART_MR_CHRL_7BITS; /* 7 bits */ + } +#ifdef HAVE_USART +#ifdef CONFIG_SAM3U_UART + /* UART does not support 9bit mode */ + + else if (priv->bits == 9 && priv->usartbase != SAM3U_UART_BASE) +#else + else if (priv->bits == 9) /* Only USARTS */ +#endif + { + regval |= USART_MR_MODE9; /* 9 bits */ + } +#endif + else /* if (priv->bits == 8) */ + { + regval |= USART_MR_CHRL_8BITS; /* 8 bits (default) */ + } + + /* OR in settings for the selected parity */ + + if (priv->parity == 1) + { + regval |= UART_MR_PAR_ODD; + } + else if (priv->parity == 2) + { + regval |= UART_MR_PAR_EVEN; + } + else + { + regval |= UART_MR_PAR_NONE; + } + + /* OR in settings for the number of stop bits */ + + if (priv->stopbits2) + { + regval |= USART_MR_NBSTOP_2; + } + else + { + regval |= USART_MR_NBSTOP_1; + } + + /* And save the new mode register value */ + + up_serialout(priv, SAM3U_UART_MR_OFFSET, regval); + + /* Configure the console baud */ + + regval = (SAM3U_MCK_FREQUENCY + (priv->baud << 3))/(priv->baud << 4); + up_serialout(priv, SAM3U_UART_BRGR_OFFSET, regval); + + /* Enable receiver & transmitter */ + + up_serialout(priv, SAM3U_UART_CR_OFFSET, (UART_CR_RXEN|UART_CR_TXEN)); +#endif + return OK; +} + +/**************************************************************************** + * Name: up_shutdown + * + * Description: + * Disable the USART. This method is called when the serial + * port is closed + * + ****************************************************************************/ + +static void up_shutdown(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + + /* Reset and disable receiver and transmitter */ + + up_serialout(priv, SAM3U_UART_CR_OFFSET, + (UART_CR_RSTRX|UART_CR_RSTTX|UART_CR_RXDIS|UART_CR_TXDIS)); + + /* Disable all interrupts */ + + up_disableallints(priv, NULL); +} + +/**************************************************************************** + * Name: up_attach + * + * Description: + * Configure the USART to operation in interrupt driven mode. This method is + * called when the serial port is opened. Normally, this is just after the + * the setup() method is called, however, the serial console may operate in + * a non-interrupt driven mode during the boot phase. + * + * RX and TX interrupts are not enabled when by the attach method (unless the + * hardware supports multiple levels of interrupt enabling). The RX and TX + * interrupts are not enabled until the txint() and rxint() methods are called. + * + ****************************************************************************/ + +static int up_attach(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + int ret; + + /* Attach and enable the IRQ */ + + ret = irq_attach(priv->irq, up_interrupt); + if (ret == OK) + { + /* Enable the interrupt (RX and TX interrupts are still disabled + * in the USART + */ + + up_enable_irq(priv->irq); + } + return ret; +} + +/**************************************************************************** + * Name: up_detach + * + * Description: + * Detach USART interrupts. This method is called when the serial port is + * closed normally just before the shutdown method is called. The exception + * is the serial console which is never shutdown. + * + ****************************************************************************/ + +static void up_detach(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + up_disable_irq(priv->irq); + irq_detach(priv->irq); +} + +/**************************************************************************** + * Name: up_interrupt + * + * Description: + * This is the USART interrupt handler. It will be invoked when an + * interrupt received on the 'irq' It should call uart_transmitchars or + * uart_receivechar to perform the appropriate data transfers. The + * interrupt handling logic must be able to map the 'irq' number into the + * approprite uart_dev_s structure in order to call these functions. + * + ****************************************************************************/ + +static int up_interrupt(int irq, void *context) +{ + struct uart_dev_s *dev = NULL; + struct up_dev_s *priv; + uint32_t pending; + int passes; + bool handled; + +#ifdef CONFIG_SAM3U_UART + if (g_uartpriv.irq == irq) + { + dev = &g_uartport; + } + else +#endif +#ifdef CONFIG_SAM3U_USART0 + if (g_usart0priv.irq == irq) + { + dev = &g_usart0port; + } + else +#endif +#ifdef CONFIG_SAM3U_USART1 + if (g_usart1priv.irq == irq) + { + dev = &g_usart1port; + } + else +#endif +#ifdef CONFIG_SAM3U_USART2 + if (g_usart2priv.irq == irq) + { + dev = &g_usart2port; + } + else +#endif +#ifdef CONFIG_SAM3U_USART3 + if (g_usart3priv.irq == irq) + { + dev = &g_usart3port; + } + else +#endif + { + PANIC(OSERR_INTERNAL); + } + priv = (struct up_dev_s*)dev->priv; + + /* Loop until there are no characters to be transferred or, until we have + * been looping for a long time. + */ + + handled = true; + for (passes = 0; passes < 256 && handled; passes++) + { + handled = false; + + /* Get the UART/USART status (we are only interested in the unmasked interrupts). */ + + priv->sr = up_serialin(priv, SAM3U_UART_SR_OFFSET); /* Save for error reporting */ + pending = priv->sr & priv->imr; /* Mask out disabled interrupt sources */ + + /* Handle an incoming, receive byte. RXRDY: At least one complete character + * has been received and US_RHR has not yet been read. + */ + + if ((pending & UART_INT_RXRDY) != 0) + { + /* Received data ready... process incoming bytes */ + + uart_recvchars(dev); + handled = true; + } + + /* Handle outgoing, transmit bytes. XRDY: There is no character in the + * US_THR. + */ + + if ((pending & UART_INT_TXRDY) != 0) + { + /* Transmit data regiser empty ... process outgoing bytes */ + + uart_xmitchars(dev); + handled = true; + } + } + return OK; +} + +/**************************************************************************** + * Name: up_ioctl + * + * Description: + * All ioctl calls will be routed through this method + * + ****************************************************************************/ + +static int up_ioctl(struct file *filep, int cmd, unsigned long arg) +{ + struct inode *inode = filep->f_inode; + struct uart_dev_s *dev = inode->i_private; + int ret = OK; + + switch (cmd) + { + case TIOCSERGSTRUCT: + { + struct up_dev_s *user = (struct up_dev_s*)arg; + if (!user) + { + ret = -EINVAL; + } + else + { + memcpy(user, dev, sizeof(struct up_dev_s)); + } + } + break; + + default: + ret = -ENOTTY; + break; + } + + return ret; +} + +/**************************************************************************** + * Name: up_receive + * + * Description: + * Called (usually) from the interrupt level to receive one + * character from the USART. Error bits associated with the + * receipt are provided in the return 'status'. + * + ****************************************************************************/ + +static int up_receive(struct uart_dev_s *dev, uint32_t *status) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + + /* Return the error information in the saved status */ + + *status = priv->sr; + priv->sr = 0; + + /* Then return the actual received byte */ + + return (int)(up_serialin(priv, SAM3U_UART_RHR_OFFSET) & 0xff); +} + +/**************************************************************************** + * Name: up_rxint + * + * Description: + * Call to enable or disable RXRDY interrupts + * + ****************************************************************************/ + +static void up_rxint(struct uart_dev_s *dev, bool enable) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + + if (enable) + { + /* Receive an interrupt when their is anything in the Rx data register (or an Rx + * timeout occurs). + */ + +#ifndef CONFIG_SUPPRESS_SERIAL_INTS + priv->imr |= UART_INT_RXRDY; + up_enableint(priv); +#endif + } + else + { + priv->imr &= ~UART_INT_RXRDY; + up_disableint(priv); + } +} + +/**************************************************************************** + * Name: up_rxavailable + * + * Description: + * Return true if the receive holding register is not empty + * + ****************************************************************************/ + +static bool up_rxavailable(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + return ((up_serialin(priv, SAM3U_UART_SR_OFFSET) & UART_INT_RXRDY) != 0); +} + +/**************************************************************************** + * Name: up_send + * + * Description: + * This method will send one byte on the UART/USART + * + ****************************************************************************/ + +static void up_send(struct uart_dev_s *dev, int ch) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + up_serialout(priv, SAM3U_UART_THR_OFFSET, (uint32_t)ch); +} + +/**************************************************************************** + * Name: up_txint + * + * Description: + * Call to enable or disable TX interrupts + * + ****************************************************************************/ + +static void up_txint(struct uart_dev_s *dev, bool enable) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + irqstate_t flags; + + flags = irqsave(); + if (enable) + { + /* Set to receive an interrupt when the TX holding register register + * is empty + */ + +#ifndef CONFIG_SUPPRESS_SERIAL_INTS + priv->imr |= UART_INT_TXRDY; + up_enableint(priv); + + /* Fake a TX interrupt here by just calling uart_xmitchars() with + * interrupts disabled (note this may recurse). + */ + + uart_xmitchars(dev); +#endif + } + else + { + /* Disable the TX interrupt */ + + priv->imr &= ~UART_INT_TXRDY; + up_disableint(priv); + } + irqrestore(flags); +} + +/**************************************************************************** + * Name: up_txready + * + * Description: + * Return true if the tranmsit holding register is empty (TXRDY) + * + ****************************************************************************/ + +static bool up_txready(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + return ((up_serialin(priv, SAM3U_UART_SR_OFFSET) & UART_INT_TXRDY) != 0); + } + +/**************************************************************************** + * Name: up_txempty + * + * Description: + * Return true if the transmit holding and shift registers are empty + * + ****************************************************************************/ + +static bool up_txempty(struct uart_dev_s *dev) +{ + struct up_dev_s *priv = (struct up_dev_s*)dev->priv; + return ((up_serialin(priv, SAM3U_UART_SR_OFFSET) & UART_INT_TXEMPTY) != 0); +} + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: up_earlyserialinit + * + * Description: + * Performs the low level USART initialization early in debug so that the + * serial console will be available during bootup. This must be called + * before up_serialinit. + * + ****************************************************************************/ + +void up_earlyserialinit(void) +{ + /* NOTE: All GPIO configuration for the USARTs was performed in + * sam3u_lowsetup + */ + + /* Disable all USARTS */ + + up_disableallints(TTYS0_DEV.priv, NULL); +#ifdef TTYS1_DEV + up_disableallints(TTYS1_DEV.priv, NULL); +#endif +#ifdef TTYS2_DEV + up_disableallints(TTYS2_DEV.priv, NULL); +#endif +#ifdef TTYS3_DEV + up_disableallints(TTYS3_DEV.priv, NULL); +#endif +#ifdef TTYS4_DEV + up_disableallints(TTYS4_DEV.priv, NULL); +#endif + + /* Configuration whichever one is the console */ + +#ifdef HAVE_CONSOLE + CONSOLE_DEV.isconsole = true; + up_setup(&CONSOLE_DEV); +#endif +} + +/**************************************************************************** + * Name: up_serialinit + * + * Description: + * Register serial console and serial ports. This assumes + * that up_earlyserialinit was called previously. + * + ****************************************************************************/ + +void up_serialinit(void) +{ + /* Register the console */ + +#ifdef HAVE_CONSOLE + (void)uart_register("/dev/console", &CONSOLE_DEV); +#endif + + /* Register all USARTs */ + + (void)uart_register("/dev/ttyS0", &TTYS0_DEV); +#ifdef TTYS1_DEV + (void)uart_register("/dev/ttyS1", &TTYS1_DEV); +#endif +#ifdef TTYS2_DEV + (void)uart_register("/dev/ttyS2", &TTYS2_DEV); +#endif +#ifdef TTYS3_DEV + (void)uart_register("/dev/ttyS3", &TTYS3_DEV); +#endif +#ifdef TTYS4_DEV + (void)uart_register("/dev/ttyS4", &TTYS4_DEV); +#endif +} + +/**************************************************************************** + * Name: up_putc + * + * Description: + * Provide priority, low-level access to support OS debug writes + * + ****************************************************************************/ + +int up_putc(int ch) +{ +#ifdef HAVE_CONSOLE + struct up_dev_s *priv = (struct up_dev_s*)CONSOLE_DEV.priv; + uint16_t imr; + + up_disableallints(priv, &imr); + + /* Check for LF */ + + if (ch == '\n') + { + /* Add CR */ + + up_lowputc('\r'); + } + + up_lowputc(ch); + up_restoreusartint(priv, imr); +#endif + return ch; +} + +#else /* CONFIG_USE_SERIALDRIVER */ + +/**************************************************************************** + * Name: up_putc + * + * Description: + * Provide priority, low-level access to support OS debug writes + * + ****************************************************************************/ + +int up_putc(int ch) +{ +#ifdef HAVE_CONSOLE + /* Check for LF */ + + if (ch == '\n') + { + /* Add CR */ + + up_lowputc('\r'); + } + + up_lowputc(ch); +#endif + return ch; +} + +#endif /* CONFIG_USE_SERIALDRIVER */ diff --git a/nuttx/arch/arm/src/stm32/stm32_lowputc.c b/nuttx/arch/arm/src/stm32/stm32_lowputc.c index bc5022cf1..8166de513 100644 --- a/nuttx/arch/arm/src/stm32/stm32_lowputc.c +++ b/nuttx/arch/arm/src/stm32/stm32_lowputc.c @@ -243,7 +243,7 @@ void stm32_lowsetup(void) { #if defined(CONFIG_STM32_USART1) || defined(CONFIG_STM32_USART2) || defined(CONFIG_STM32_USART3) uint32_t mapr; -#if defined(HAVE_CONSOLE) && !defined(CONFIG_SUPPRESS_USART_CONFIG) +#if defined(HAVE_CONSOLE) && !defined(CONFIG_SUPPRESS_UART_CONFIG) uint32_t cr; #endif @@ -332,7 +332,7 @@ void stm32_lowsetup(void) /* Enable and configure the selected console device */ -#if defined(HAVE_CONSOLE) && !defined(CONFIG_SUPPRESS_USART_CONFIG) +#if defined(HAVE_CONSOLE) && !defined(CONFIG_SUPPRESS_UART_CONFIG) /* Configure CR2 */ cr = getreg32(STM32_CONSOLE_BASE + STM32_USART_CR2_OFFSET); diff --git a/nuttx/arch/arm/src/stm32/stm32_serial.c b/nuttx/arch/arm/src/stm32/stm32_serial.c index d3c1f4130..f3bdf5e30 100644 --- a/nuttx/arch/arm/src/stm32/stm32_serial.c +++ b/nuttx/arch/arm/src/stm32/stm32_serial.c @@ -425,7 +425,7 @@ static inline void up_disableusartint(struct up_dev_s *priv, uint16_t *ie) static int up_setup(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; -#ifdef CONFIG_SUPPRESS_USART_CONFIG +#ifdef CONFIG_SUPPRESS_UART_CONFIG uint32_t uartdiv32; uint32_t mantissa; uint32_t fraction; diff --git a/nuttx/configs/sam3u-ek/include/board.h b/nuttx/configs/sam3u-ek/include/board.h index 4ba49e224..3376b3993 100755 --- a/nuttx/configs/sam3u-ek/include/board.h +++ b/nuttx/configs/sam3u-ek/include/board.h @@ -86,23 +86,15 @@ /* LED definitions ******************************************************************/ -#define LED_STARTED 0 -#define LED_HEAPALLOCATE 1 -#define LED_IRQSENABLED 2 -#define LED_STACKCREATED 3 -#define LED_INIRQ 4 -#define LED_SIGNAL 5 -#define LED_ASSERTION 6 -#define LED_PANIC 7 - -/* GPIO pin definitions *************************************************************/ - -#define GPIO_LED0 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_CLEAR|GPIO_PIN0) -#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN1) -#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN2) - -#define GPIO_BUTTON1 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN18) -#define GPIO_BUTTON2 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN19) +#define LED_STARTED 0 /* LED0=OFF LED1=OFF LED2=OFF */ +#define LED_HEAPALLOCATE 1 /* LED0=OFF LED1=OFF LED2=ON */ +#define LED_IRQSENABLED 2 /* LED0=OFF LED1=ON LED2=OFF */ +#define LED_STACKCREATED 3 /* LED0=OFF LED1=ON LED2=ON */ + +#define LED_INIRQ 4 /* LED0=OFF LED1=TOG LED2=XXX */ +#define LED_SIGNAL 5 /* LED0=OFF LED1=XXX LED2=TOG */ +#define LED_ASSERTION 6 /* LED0=TOG LED1=XXX LED2=XXX */ +#define LED_PANIC 7 /* LED0=TOG LED1=XXX LED2=XXX*/ /************************************************************************************ * Public Data diff --git a/nuttx/configs/sam3u-ek/ostest/defconfig b/nuttx/configs/sam3u-ek/ostest/defconfig index 7c5b33c31..33f1ee3ec 100755 --- a/nuttx/configs/sam3u-ek/ostest/defconfig +++ b/nuttx/configs/sam3u-ek/ostest/defconfig @@ -100,7 +100,7 @@ CONFIG_SAM3U_BUILDROOT=y # # Individual subsystems can be enabled: # -CONFIG_SAM3U_USART=y +CONFIG_SAM3U_UART=y CONFIG_SAM3U_USART0=n CONFIG_SAM3U_USART1=n CONFIG_SAM3U_USART2=n diff --git a/nuttx/configs/sam3u-ek/src/sam3uek_internal.h b/nuttx/configs/sam3u-ek/src/sam3uek_internal.h index 9c13dc5f5..fde22f7d8 100755 --- a/nuttx/configs/sam3u-ek/src/sam3uek_internal.h +++ b/nuttx/configs/sam3u-ek/src/sam3uek_internal.h @@ -51,10 +51,19 @@ /* SAM3U-EK GPIOs *******************************************************************/ +/* GPIO pin definitions *************************************************************/ + /* LEDs */ +#define GPIO_LED0 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_CLEAR|GPIO_PIN0) +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN1) +#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN2) + /* BUTTONS */ +#define GPIO_BUTTON1 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN18) +#define GPIO_BUTTON2 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN19) + /* SPI Chip Selects */ /************************************************************************************ diff --git a/nuttx/configs/sam3u-ek/src/up_leds.c b/nuttx/configs/sam3u-ek/src/up_leds.c index 8ec9a4707..09acb23de 100755 --- a/nuttx/configs/sam3u-ek/src/up_leds.c +++ b/nuttx/configs/sam3u-ek/src/up_leds.c @@ -2,7 +2,7 @@ * configs/sam3u-ek/src/up_leds.c * arch/arm/src/board/up_leds.c * - * Copyright (C) 2009 Gregory Nutt. All rights reserved. + * Copyright (C) 2009-2010 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without @@ -52,6 +52,8 @@ #include "sam3u_internal.h" #include "sam3uek_internal.h" +#ifdef CONFIG_ARCH_LEDS + /**************************************************************************** * Definitions ****************************************************************************/ @@ -70,14 +72,95 @@ # define ledvdbg(x...) #endif +#define LED_OFF 0 +#define LED_ON 1 +#define LED_NOCHANGE 2 +#define LED_MASK 3 + +#define LED0_SHIFT 0 +#define LED0_OFF (LED_OFF << LED0_SHIFT) +#define LED0_ON (LED_ON << LED0_SHIFT) +#define LED0_NOCHANGE (LED_NOCHANGE << LED0_SHIFT) +#define LED1_SHIFT 2 +#define LED1_OFF (LED_OFF << LED1_SHIFT) +#define LED1_ON (LED_ON << LED1_SHIFT) +#define LED1_NOCHANGE (LED_NOCHANGE << LED1_SHIFT) +#define LED2_SHIFT 4 +#define LED2_OFF (LED_OFF << LED2_SHIFT) +#define LED2_ON (LED_ON << LED2_SHIFT) +#define LED2_NOCHANGE (LED_NOCHANGE << LED2_SHIFT) + /**************************************************************************** * Private Data ****************************************************************************/ +static const uint8_t g_ledon[8] = +{ + + (LED0_OFF |LED1_OFF |LED2_OFF), /* LED_STARTED */ + (LED0_ON |LED1_OFF |LED2_ON), /* LED_HEAPALLOCATE */ + (LED0_OFF |LED1_ON |LED2_OFF), /* LED_IRQSENABLED */ + (LED0_ON |LED1_ON |LED2_ON), /* LED_STACKCREATED */ + + (LED0_OFF |LED1_OFF |LED2_NOCHANGE), /* LED_INIRQ */ + (LED0_OFF |LED1_NOCHANGE|LED2_OFF), /* LED_SIGNAL */ + (LED0_ON |LED1_NOCHANGE|LED2_NOCHANGE), /* LED_ASSERTION */ + (LED0_ON |LED1_NOCHANGE|LED2_NOCHANGE) /* LED_PANIC */ +}; + +static const uint8_t g_ledoff[8] = +{ + + (LED0_OFF |LED1_OFF |LED2_OFF), /* LED_STARTED (does not happen) */ + (LED0_ON |LED1_OFF |LED2_ON), /* LED_HEAPALLOCATE (does not happen) */ + (LED0_OFF |LED1_ON |LED2_OFF), /* LED_IRQSENABLED (does not happen) */ + (LED0_ON |LED1_ON |LED2_ON), /* LED_STACKCREATED (does not happen) */ + + (LED0_OFF |LED1_ON |LED2_NOCHANGE), /* LED_INIRQ */ + (LED0_OFF |LED1_NOCHANGE|LED2_ON), /* LED_SIGNAL */ + (LED0_OFF |LED1_NOCHANGE|LED2_NOCHANGE), /* LED_ASSERTION */ + (LED0_OFF |LED1_NOCHANGE|LED2_NOCHANGE) /* LED_PANIC */ +}; + /**************************************************************************** * Private Functions ****************************************************************************/ +/**************************************************************************** + * Name: up_setled + ****************************************************************************/ + +static void up_setled(uint16_t pinset, uint8_t state) +{ + /* Assume active high. Initial state == 0 means active high */ + + bool polarity = ((pinset & GPIO_OUTPUT_SET) == 0); + switch (state) + { + case LED_OFF: + polarity = !polarity; + + case LED_ON: + break; + + case LED_NOCHANGE: + default: + return; + } + sam3u_gpiowrite(pinset, polarity); +} + +/**************************************************************************** + * Name: up_setleds + ****************************************************************************/ + +static void up_setleds(uint8_t state) +{ + up_setled(GPIO_LED0, (state >> LED0_SHIFT) & LED_MASK); + up_setled(GPIO_LED1, (state >> LED1_SHIFT) & LED_MASK); + up_setled(GPIO_LED2, (state >> LED2_SHIFT) & LED_MASK); +} + /**************************************************************************** * Public Functions ****************************************************************************/ @@ -86,9 +169,11 @@ * Name: up_ledinit ****************************************************************************/ -#ifdef CONFIG_ARCH_LEDS void up_ledinit(void) { + (void)sam3u_configgpio(GPIO_LED0); + (void)sam3u_configgpio(GPIO_LED1); + (void)sam3u_configgpio(GPIO_LED2); } /**************************************************************************** @@ -97,6 +182,7 @@ void up_ledinit(void) void up_ledon(int led) { + up_setleds(g_ledon[led & 7]); } /**************************************************************************** @@ -105,6 +191,7 @@ void up_ledon(int led) void up_ledoff(int led) { + up_setleds(g_ledoff[led & 7]); } #endif /* CONFIG_ARCH_LEDS */ -- cgit v1.2.3