From 7b13fdf0152c49dc131313a795c373de3b5af50d Mon Sep 17 00:00:00 2001 From: patacongo Date: Thu, 30 Aug 2012 15:44:02 +0000 Subject: Remove documentation from defconfig files so that they are more maintainable git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5068 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig | 436 +--------------------- 1 file changed, 1 insertion(+), 435 deletions(-) (limited to 'nuttx/configs/lpcxpresso-lpc1768/ostest') diff --git a/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig b/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig index dc65893f9..69da0df72 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig +++ b/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig @@ -33,40 +33,7 @@ # ############################################################################ # -# architecture selection -# -# CONFIG_ARCH - identifies the arch subdirectory and, hence, the -# processor architecture. -# CONFIG_ARCH_family - for use in C code. This identifies the -# particular chip family that the architecture is implemented -# in. -# CONFIG_ARCH_architecture - for use in C code. This identifies the -# specific architecture within the chip familyl. -# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory -# CONFIG_ARCH_CHIP_name - For use in C code -# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, -# the board that supports the particular chip or SoC. -# CONFIG_ARCH_BOARD_name - for use in C code -# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) -# CONFIG_BOARD_LOOPSPERMSEC - for delay loops -# CONFIG_DRAM_SIZE - Describes the installed DRAM. -# CONFIG_DRAM_START - The start address of DRAM (physical) -# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization -# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt -# stack. If defined, this symbol is the size of the interrupt -# stack in bytes. If not defined, the user task stacks will be -# used during interrupt handling. -# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions -# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. -# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. -# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. -# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that -# cause a 100 second delay during boot-up. This 100 second delay -# serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure -# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until -# the delay actually is 100 seconds. -# CONFIG_ARCH_DMA - Support DMA initialization +# Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y @@ -97,11 +64,8 @@ CONFIG_LPC17_BUILDROOT=n CONFIG_LPC17_CODEREDW=n CONFIG_LPC17_CODEREDL=y -# -# Individual subsystems can be enabled: # # Individual subsystems can be enabled: -# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) # CONFIG_LPC17_ETHERNET=n CONFIG_LPC17_USBHOST=n @@ -136,17 +100,6 @@ CONFIG_LPC17_GPDMA=n # # LPC17xx specific serial device driver settings # -# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the -# console and ttys0 (default is the UART1). -# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. -# This specific the size of the receive buffer -# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before -# being sent. This specific the size of the transmit buffer -# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be -# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. -# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity -# CONFIG_UARTn_2STOP - Two stop bits -# CONFIG_UART0_SERIAL_CONSOLE=n CONFIG_UART1_SERIAL_CONSOLE=n CONFIG_UART2_SERIAL_CONSOLE=n @@ -185,24 +138,6 @@ CONFIG_UART3_2STOP=0 # # LPC17xx specific PHY/Ethernet device driver settings # -# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY -# CONFIG_PHY_DP83848C - Selects National Semiconductor DP83848C PHY -# CONFIG_PHY_LAN8720 - Selects SMSC LAN8720 PHY -# CONFIG_PHY_AUTONEG - Enable auto-negotion -# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. -# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex -# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb -# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 -# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 -# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is -# the higest priority. -# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). -# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs -# CONFIG_DEBUG. -# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. -# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. -# Automatically set if CONFIG_NET_IGMP is selected. -# CONFIG_PHY_KS8721=n CONFIG_PHY_DP83848C=n CONFIG_PHY_LAN8720=y @@ -213,19 +148,6 @@ CONFIG_PHY_FDUPLEX=y # # General build options # -# CONFIG_RRLOAD_BINARY - make the rrload binary format used with -# BSPs from www.ridgerun.com using the tools/mkimage.sh script -# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format -# used with many different loaders using the GNU objcopy program -# Should not be selected if you are not using the GNU toolchain. -# CONFIG_RAW_BINARY - make a raw binary format file used with many -# different loaders using the GNU objcopy program. This option -# should not be selected if you are not using the GNU toolchain. -# CONFIG_HAVE_LIBM - toolchain supports libm.a -# CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n @@ -235,93 +157,6 @@ CONFIG_HAVE_LIBM=n # # General OS setup # -# CONFIG_APPS_DIR - Identifies the relative path to the directory -# that builds the application to link with NuttX. Default: ../apps -# CONFIG_DEBUG - enables built-in debug options -# CONFIG_DEBUG_VERBOSE - enables verbose debug output -# CONFIG_DEBUG_SYMBOLS - build without optimization and with -# debug symbols (needed for use with a debugger). -# CONFIG_MM_REGIONS - If the architecture includes multiple -# regions of memory to allocate from, this specifies the -# number of memory regions that the memory manager must -# handle and enables the API mm_addregion(start, end); -# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot -# time console output -# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz -# or MSEC_PER_TICK=10. This setting may be defined to -# inform NuttX that the processor hardware is providing -# system timer interrupts at some interrupt interval other -# than 10 msec. -# CONFIG_RR_INTERVAL - The round robin timeslice will be set -# this number of milliseconds; Round robin scheduling can -# be disabled by setting this value to zero. -# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in -# scheduler to monitor system performance -# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a -# task name to save in the TCB. Useful if scheduler -# instrumentation is selected. Set to zero to disable. -# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - -# Used to initialize the internal time logic. -# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. -# You would only need this if you are concerned about accurate -# time conversions in the past or in the distant future. -# CONFIG_JULIAN_TIME - Enables Julian time conversions. You -# would only need this if you are concerned about accurate -# time conversion in the distand past. You must also define -# CONFIG_GREGORIAN_TIME in order to use Julian time. -# CONFIG_DEV_CONSOLE - Set if architecture-specific logic -# provides /dev/console. Enables stdout, stderr, stdin. -# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console -# driver (minimul support) -# CONFIG_MUTEX_TYPES: Set to enable support for recursive and -# errorcheck mutexes. Enables pthread_mutexattr_settype(). -# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority -# inheritance on mutexes and semaphores. -# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority -# inheritance is enabled. It defines the maximum number of -# different threads (minus one) that can take counts on a -# semaphore with priority inheritance support. This may be -# set to zero if priority inheritance is disabled OR if you -# are only using semaphores as mutexes (only one holder) OR -# if no more than two threads participate using a counting -# semaphore. -# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, -# then this setting is the maximum number of higher priority -# threads (minus 1) than can be waiting for another thread -# to release a count on a semaphore. This value may be set -# to zero if no more than one thread is expected to wait for -# a semaphore. -# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors -# by task_create() when a new task is started. If set, all -# files/drivers will appear to be closed in the new task. -# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first -# three file descriptors (stdin, stdout, stderr) by task_create() -# when a new task is started. If set, all files/drivers will -# appear to be closed in the new task except for stdin, stdout, -# and stderr. -# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket -# desciptors by task_create() when a new task is started. If -# set, all sockets will appear to be closed in the new task. -# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to -# handle delayed processing from interrupt handlers. This feature -# is required for some drivers but, if there are not complaints, -# can be safely disabled. The worker thread also performs -# garbage collection -- completing any delayed memory deallocations -# from interrupt handlers. If the worker thread is disabled, -# then that clean will be performed by the IDLE thread instead -# (which runs at the lowest of priority and may not be appropriate -# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE -# is enabled, then the following options can also be used: -# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker -# thread. Default: 50 -# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for -# work in units of microseconds. Default: 50000 (50 MS). -# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker -# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. -# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up -# the worker thread. Default: 4 -# -#CONFIG_APPS_DIR= CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_SYMBOLS=n @@ -352,15 +187,6 @@ CONFIG_SIG_SIGWORK=4 # # Settings for nxflat -# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. -# This format will support execution of NuttX binaries located -# in a ROMFS filesystem (see examples/nxflat). -# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals -# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and -# CONFIG_DEBUG_BINFMT have to be defined or -# CONFIG_NXFLAT_DUMPBUFFER does nothing. -# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table -# is ordered by symbol name # CONFIG_NXFLAT=n CONFIG_NXFLAT_DUMPBUFFER=n @@ -393,9 +219,6 @@ CONFIG_DISABLE_POLL=y # # Misc libc settings # -# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a -# little smaller if we do not support fieldwidthes -# CONFIG_NOPRINTF_FIELDWIDTH=n # @@ -418,38 +241,6 @@ CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # -# CONFIG_MAX_TASKS - The maximum number of simultaneously -# active tasks. This value must be a power of two. -# CONFIG_MAX_TASK_ARGS - This controls the maximum number of -# of parameters that a task may receive (i.e., maxmum value -# of 'argc') -# CONFIG_NPTHREAD_KEYS - The number of items of thread- -# specific data that can be retained -# CONFIG_NFILE_DESCRIPTORS - The maximum number of file -# descriptors (one for each open) -# CONFIG_NFILE_STREAMS - The maximum number of streams that -# can be fopen'ed -# CONFIG_NAME_MAX - The maximum size of a file name. -# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate -# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_NUNGET_CHARS - Number of characters that can be -# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) -# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message -# structures. The system manages a pool of preallocated -# message structures to minimize dynamic allocations -# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with -# a fixed payload size given by this settin (does not include -# other message structure overhead. -# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that -# can be passed to a watchdog handler -# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog -# structures. The system manages a pool of preallocated -# watchdog structures to minimize dynamic allocations -# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX -# timer structures. The system manages a pool of preallocated -# timer structures to minimize dynamic allocations. Set to -# zero for all dynamic allocations. -# CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 @@ -467,23 +258,12 @@ CONFIG_PREALLOC_TIMERS=4 # # Filesystem configuration # -# CONFIG_FS_FAT - Enable FAT filesystem support -# CONFIG_FAT_SECTORSIZE - Max supported sector size -# CONFIG_FS_ROMFS - Enable ROMFS filesystem support -# CONFIG_FS_FAT=n CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # -# CONFIG_MMCSD_NSLOTS -# Number of MMC/SD slots supported by the driver -# CONFIG_MMCSD_READONLY -# Provide read-only access (default is read/write) -# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. -# Default is 20MHz. -# CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 @@ -491,53 +271,18 @@ CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # -# CONFIG_FS_READAHEAD -# Enable read-ahead buffering -# CONFIG_FS_WRITEBUFFER -# Enable write buffering -# CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # -# CONFIG_SDIO_DMA -# SDIO driver supports DMA -# CONFIG_MMCSD_MMCSUPPORT -# Enable support for MMC cards -# CONFIG_MMCSD_HAVECARDDETECT -# SDIO driver card detection is 100% accurate -# CONFIG_SDIO_DMA=n CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP -# CONFIG_NET - Enable or disable all network features -# CONFIG_NET_IPv6 - Build in support for IPv6 -# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. -# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options -# CONFIG_NET_BUFSIZE - uIP buffer size -# CONFIG_NET_TCP - TCP support on or off -# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) -# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers -# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) -# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until -# accept() is called. The size of the backlog is selected when listen() is called. -# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) -# CONFIG_NET_UDP - UDP support on or off -# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off -# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections -# CONFIG_NET_ICMP - ICMP ping response support on or off -# CONFIG_NET_ICMP_PING - ICMP ping request support on or off -# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address -# CONFIG_NET_STATISTICS - uIP statistics on or off -# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window -# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table -# CONFIG_NET_BROADCAST - Broadcast support -# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates # CONFIG_NET=n CONFIG_NET_IPv6=n @@ -561,8 +306,6 @@ CONFIG_NET_BROADCAST=n # # UIP Network Utilities -# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP -# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 @@ -570,22 +313,6 @@ CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # -# CONFIG_USBDEV -# Enables USB device support -# CONFIG_USBDEV_ISOCHRONOUS -# Build in extra support for isochronous endpoints -# CONFIG_USBDEV_DUALSPEED -# Hardware handles high and full speed operation (USB 2.0) -# CONFIG_USBDEV_SELFPOWERED -# Will cause USB features to indicate that the device is -# self-powered -# CONFIG_USBDEV_MAXPOWER -# Maximum power consumption in mA -# CONFIG_USBDEV_TRACE -# Enables USB tracing for debug -# CONFIG_USBDEV_TRACE_NRECORDS -# Number of trace entries to remember -# CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n @@ -598,23 +325,6 @@ CONFIG_USBDEV_TRACE_NRECORDS=128 # # LPC17xx USB Configuration # -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT -# Handle USB Start-Of-Frame events. -# Enable reading SOF from interrupt handler vs. simply reading on demand. -# Probably a bad idea... Unless there is some issue with sampling the SOF -# from hardware asynchronously. -# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT -# Enable high priority interrupts. I have no idea why you might want to -# do that -# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS -# Number of DMA descriptors to allocate in SRAM. -# CONFIG_LPC17_USBDEV_DMA -# Enable lpc17xx-specific DMA support -# CONFIG_LPC17_USBDEV_NOVBUS -# Define if the hardware implementation does not support the VBUS signal -# CONFIG_LPC17_USBDEV_NOLED -# Define if the hardware implementation does not support the LED output -# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n CONFIG_LPC17_USBDEV_DMA=n @@ -626,26 +336,6 @@ CONFIG_LPC17_USBDEV_NOLED=y # # USB Serial Device Configuration # -# CONFIG_PL2303 -# Enable compilation of the USB serial driver -# CONFIG_PL2303_EPINTIN -# The logical 7-bit address of a hardware endpoint that supports -# interrupt IN operation -# CONFIG_PL2303_EPBULKOUT -# The logical 7-bit address of a hardware endpoint that supports -# bulk OUT operation -# CONFIG_PL2303_EPBULKIN -# The logical 7-bit address of a hardware endpoint that supports -# bulk IN operation -# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR -# The vendor ID code/string -# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR -# The product ID code/string -# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE -# Size of the serial receive/transmit buffers -# CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 @@ -662,26 +352,6 @@ CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # -# CONFIG_USBMSC -# Enable compilation of the USB storage driver -# CONFIG_USBMSC_EP0MAXPACKET -# Max packet size for endpoint 0 -# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN -# The logical 7-bit address of a hardware endpoints that support -# bulk OUT and IN operations -# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS -# The number of write/read requests that can be in flight -# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN -# The size of the buffer in each write/read request. This -# value needs to be at least as large as the endpoint -# maxpacket and ideally as large as a block device sector. -# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR -# The vendor ID code/string -# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR -# The product ID code/string -# CONFIG_USBMSC_REMOVABLE -# Select if the media is removable -# CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 @@ -708,19 +378,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest # -# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act -# as either the client side or server side of the test -# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the -# client side simply receives messages forever, allowing -# measurement of throughput -# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has -# no MAC address; one will be assigned -# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address -# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address -# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask -# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the -# client side of the test (may be target or host) -# CONFIG_EXAMPLE_NETTEST_SERVER=n CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n CONFIG_EXAMPLE_NETTEST_NOMAC=y @@ -739,36 +396,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for apps/nshlib # -# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer -# CONFIG_NSH_STRERROR - Use strerror(errno) -# CONFIG_NSH_LINELEN - Maximum length of one command line -# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi -# CONFIG_NSH_DISABLESCRIPT - Disable scripting support -# CONFIG_NSH_DISABLEBG - Disable background commands -# CONFIG_NSH_ROMFSETC - Use startup script in /etc -# CONFIG_NSH_CONSOLE - Use serial console front end -# CONFIG_NSH_TELNET - Use telnetd console front end -# CONFIG_NSH_ARCHINIT - Platform provides architecture -# specific initialization (nsh_archinitialize()). -# -# If CONFIG_NSH_TELNET is selected: -# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size -# CONFIG_NSH_DHCPC - Obtain address using DHCP -# CONFIG_NSH_IPADDR - Provides static IP address -# CONFIG_NSH_DRIPADDR - Provides static router IP address -# CONFIG_NSH_NETMASK - Provides static network mask -# CONFIG_NSH_NOMAC - Use a bogus MAC address -# -# If CONFIG_NSH_ROMFSETC is selected: -# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint -# CONFIG_NSH_INITSCRIPT - Relative path to init script -# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor -# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size -# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor -# CONFIG_NSH_FATSECTSIZE - FAT FS sector size -# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors -# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint -# CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 @@ -804,15 +431,6 @@ CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # -# CONFIG_EXAMPLES_USBSERIAL_INONLY -# Only verify IN (device-to-host) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_OUTONLY -# Only verify OUT (host-to-device) data transfers. Default: both -# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL -# Send only small, single packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG -# Send only large, multi-packet messages. Default: Send large and small. -# CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n @@ -827,38 +445,6 @@ CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/usbstorage # -# CONFIG_EXAMPLES_USBMSC_NLUNS -# Defines the number of logical units (LUNs) exported by the USB storage -# driver. Each LUN corresponds to one exported block driver (or partition -# of a block driver). May be 1, 2, or 3. Default is 1. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR1 -# The minor device number of the block driver for the first LUN. For -# example, N in /dev/mmcsdN. Used for registering the block driver. Default -# is zero. -# CONFIG_EXAMPLES_USBMSC_DEVPATH1 -# The full path to the registered block driver. Default is "/dev/mmcsd0" -# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 2 or 3. No defaults. -# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3 -# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS -# is 3. No defaults. -# -# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then -# the example code will also manage the USB trace output. The amount of trace output -# can be controlled using: -# -# CONFIG_EXAMPLES_USBMSC_TRACEINIT -# Show initialization events -# CONFIG_EXAMPLES_USBMSC_TRACECLASS -# Show class driver events -# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS -# Show data transfer events -# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER -# Show controller events -# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS -# Show interrupt-related events. -# CONFIG_EXAMPLES_USBMSC_NLUNS=1 CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0 CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0" @@ -871,26 +457,6 @@ CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n # # Stack and heap information # -# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP -# operation from FLASH but must copy initialized .data sections to RAM. -# (should also be =n for the LPC17xx which always runs from flash) -# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH -# but copy themselves entirely into RAM for better performance. -# CONFIG_CUSTOM_STACK - The up_ implementation will handle -# all stack operations outside of the nuttx model. -# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) -# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. -# This is the thread that (1) performs the inital boot of the system up -# to the point where user_start() is spawned, and (2) there after is the -# IDLE thread that executes only when there is no other thread ready to -# run. -# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate -# for the main user thread that begins at the user_start() entry point. -# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size -# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size -# CONFIG_HEAP_BASE - The beginning of the heap -# CONFIG_HEAP_SIZE - The size of the heap -# CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n -- cgit v1.2.3