From 48bbe68916ccaf0d2fa050e945bf650384ca624f Mon Sep 17 00:00:00 2001 From: patacongo Date: Sat, 1 May 2010 19:21:06 +0000 Subject: Add nettest config for str-p711 using enc28j60 git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2642 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/configs/olimex-strp711/README.txt | 38 ++ nuttx/configs/olimex-strp711/nettest/Make.defs | 160 ++++++ nuttx/configs/olimex-strp711/nettest/defconfig | 767 +++++++++++++++++++++++++ nuttx/configs/olimex-strp711/nettest/ld.script | 122 ++++ nuttx/configs/olimex-strp711/nettest/setenv.sh | 47 ++ 5 files changed, 1134 insertions(+) create mode 100755 nuttx/configs/olimex-strp711/nettest/Make.defs create mode 100755 nuttx/configs/olimex-strp711/nettest/defconfig create mode 100755 nuttx/configs/olimex-strp711/nettest/ld.script create mode 100755 nuttx/configs/olimex-strp711/nettest/setenv.sh (limited to 'nuttx/configs/olimex-strp711') diff --git a/nuttx/configs/olimex-strp711/README.txt b/nuttx/configs/olimex-strp711/README.txt index 14b1664ef..2f7431a03 100644 --- a/nuttx/configs/olimex-strp711/README.txt +++ b/nuttx/configs/olimex-strp711/README.txt @@ -228,9 +228,47 @@ GENERAL STEPS: The same commands from the telnet interface can now be accessed through the 'monitor' command, e.g. 'monitor help' +ENC28J60 Module +^^^^^^^^^^^^^^^ + + Module CON5 QFN ENC2860 Description + --------------- ------------------------------------------------------- + 1 J8-1 NET CS 5 ~CS Chip select input pin for SPI interface (active low) + 2 2 SCK 4 SCK Clock in pin for SPI interface + 3 3 MOSI 3 SI Data in pin for SPI interface + 4 4 MISO 2 SO Data out pin for SPI interface + 5 5 GND -- --- --- + 10 J9-1 3V3 -- --- --- + 9 2 WOL 1 ~WOL Unicast WOL filter + 8 3 NET INT 28 ~INT Interrupt output pin (active low) + 7 4 CLKOUT 27 CLKOUT Programmable clock output pin + 6 5 NET RST 6 ~RESET Active-low device Reset input + + For the Olimex STR-P711, the ENC28J60 module is placed on SPI1 (with + the MMC slot) and uses P0.0 for CS, P0.1 for an interrupt, and P0.2 as + a reset: + + Module CON5 Olimex STR-P711 Connection + --------------- ------------------------------------------------------- + 1 J8-1 NET CS SPI0-4 P0.0 P0.0/S0.MISO/U3.TX + 2 2 SCK SPI1-5 SCLK1 P0.6/S1.SCLK + 3 3 MOSI SPI1-3 MOSI1 P0.5/S1.MOSI + 4 4 MISO SPI1-4 MISO1 P0.4/S1.MISO + 5 5 GND SPI1-1 GND + 10 J9-1 3V3 SPI1-6 3.3V + 9 2 WOL NC + 8 3 NET INT SPI0-3 P0.1 P0.1/S0.MOSI/U3.RX + 7 4 CLKOUT NC + 6 5 NET RST SPI0-5 P0.2 P0.2/S0 + Configurations: --------------- + nettest: + This configuration directory may be used to enable networking using the + an Microchip ENC28J60 SPI ethernet module (see above for connection to + STR-P711. + nsh: Configures the NuttShell (nsh) located at examples/nsh. The Configuration enables both the serial and telnetd NSH interfaces. diff --git a/nuttx/configs/olimex-strp711/nettest/Make.defs b/nuttx/configs/olimex-strp711/nettest/Make.defs new file mode 100755 index 000000000..391691e8f --- /dev/null +++ b/nuttx/configs/olimex-strp711/nettest/Make.defs @@ -0,0 +1,160 @@ +############################################################################## +# configs/olimex-strp711/nettest/Make.defs +# +# Copyright (C) 2010 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################## + +include ${TOPDIR}/.config + +# The default value for CROSSDEV can be overridden from the make command line: +# make -- Will build for the NuttX buildroot toolchain +# make CROSSDEV=arm-eabi- -- Will build for the devkitARM toolchain +# make CROSSDEV=arm-none-eabi- -- Will build for the CodeSourcery toolchain +# make CROSSDEV=arm-elf- -- Will build for the NuttX buildroot toolchain + +CROSSDEV = arm-elf- +CC = $(CROSSDEV)gcc +CXX = $(CROSSDEV)g++ +CPP = $(CROSSDEV)gcc -E +LD = $(CROSSDEV)ld +AR = $(CROSSDEV)ar rcs +NM = $(CROSSDEV)nm +OBJCOPY = $(CROSSDEV)objcopy +OBJDUMP = $(CROSSDEV)objdump + +HOSTOS = ${shell uname -o} + +ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'} +ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1} + +ifeq ($(ARCHCCMAJOR),4) +ifneq ($(HOSTOS),Cygwin) +OBJCOPYARGS = -R .note -R .note.gnu.build-id -R .comment +endif +endif + +ifeq ($(CROSSDEV),arm-elf-) + MKDEP = $(TOPDIR)/tools/mkdeps.sh + ARCHINCLUDES = -I. -isystem $(TOPDIR)/include + ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx + ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nettest/ld.script + MAXOPTIMIZATION = -Os +else + WINTOOL = y + DIRLINK = $(TOPDIR)/tools/winlink.sh + DIRUNLINK = $(TOPDIR)/tools/unlink.sh + MKDEP = $(TOPDIR)/tools/mknulldeps.sh + ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" + ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}" + ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nettest/ld.script}" + MAXOPTIMIZATION = -O2 +endif + +ifeq ("${CONFIG_DEBUG_SYMBOLS}","y") + ARCHOPTIMIZATION = -g +else + ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer +endif + +ifeq ($(ARCHCCMAJOR),4) + ARCHCPUFLAGS = -mcpu=arm7tdmi -mfloat-abi=soft +else + ARCHCPUFLAGS = -mapcs-32 -mcpu=arm7tdmi -msoft-float +endif + +ARCHCFLAGS = -fno-builtin +ARCHCXXFLAGS = -fno-builtin -fno-exceptions +ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10 +ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow +ARCHWARNINGSXX = -Wall -Wshadow +ARCHDEFINES = + +CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) \ + $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) -pipe +CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS) +CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) \ + $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) -pipe +CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS) +CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) +AFLAGS = $(CFLAGS) -D__ASSEMBLY__ + +NXFLATLDFLAGS1 = -r -d -warn-common +NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) \ + -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld \ + -no-check-sections +LDNXFLATFLAGS = -e main -s 2048 + +OBJEXT = .o +LIBEXT = .a +EXEEXT = + +ifneq ($(CROSSDEV),arm-elf-) + LDFLAGS += -nostartfiles -nodefaultlibs +endif +ifeq ($(CONFIG_DEBUG_SYMBOLS),y) + LDFLAGS += -g +endif + +define PREPROCESS + @echo "CPP: $1->$2" + @$(CPP) $(CPPFLAGS) $1 -o $2 +endef + +define COMPILE + @echo "CC: $1" + @$(CC) -c $(CFLAGS) $1 -o $2 +endef + +define COMPILEXX + @echo "CXX: $1" + @$(CXX) -c $(CXXFLAGS) $1 -o $2 +endef + +define ASSEMBLE + @echo "AS: $1" + @$(CC) -c $(AFLAGS) $1 -o $2 +endef + +define ARCHIVE + echo "AR: $2"; \ + $(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; } +endef + +define CLEAN + @rm -f *.o *.a +endef + +HOSTCC = gcc +HOSTINCLUDES = -I. +HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe +HOSTLDFLAGS = + diff --git a/nuttx/configs/olimex-strp711/nettest/defconfig b/nuttx/configs/olimex-strp711/nettest/defconfig new file mode 100755 index 000000000..6187d5efe --- /dev/null +++ b/nuttx/configs/olimex-strp711/nettest/defconfig @@ -0,0 +1,767 @@ +############################################################################ +# configs/olimes-strp711/nettest/defconfig +# +# Copyright (C) 2010 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +# +# Architecture selection +# +# CONFIG_ARCH - identifies the arch subdirectory and, hence, the +# processor architecture. +# CONFIG_ARCH_family - for use in C code. This identifies the +# particular chip family that the architecture is implemented +# in. +# CONFIG_ARCH_architecture - for use in C code. This identifies the +# specific architecture within the chip familyl. +# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory +# CONFIG_ARCH_CHIP_name - For use in C code +# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, +# the board that supports the particular chip or SoC. +# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) +# CONFIG_ARCH_BOARD_name - for use in C code +# CONFIG_ARCH_NOINTC - define if the architecture does not +# support an interrupt controller or otherwise cannot support +# APIs like up_enable_irq() and up_disable_irq(). +# CONFIG_ARCH_IRQPRIO +# Define if the architecture suports prioritizaton of interrupts +# and the up_prioritize_irq() API. +# CONFIG_BOARD_LOOPSPERMSEC - for delay loops +# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to Olimex STR-P711 +# CONFIG_ARCH_BUTTONS - Support reading buttons. Unique to Olimex STR-P711 +# CONFIG_DRAM_SIZE - Describes the internal DRAM. +# CONFIG_DRAM_START - The start address of internal DRAM +# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt +# stack. If defined, this symbol is the size of the interrupt +# stack in bytes. If not defined, the user task stacks will be +# used during interrupt handling. +# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions +# +CONFIG_ARCH=arm +CONFIG_ARCH_ARM=y +CONFIG_ARCH_ARM7TDMI=y +CONFIG_ARCH_CHIP=str71x +CONFIG_ARCH_STR71X=y +CONFIG_ARCH_BOARD=olimex-strp711 +CONFIG_ARCH_BOARD_OLIMEX_STRP711=y +CONFIG_ARCH_NOINTC=n +CONFIG_ARCH_IRQPRIO=y +CONFIG_BOARD_LOOPSPERMSEC=1431 +CONFIG_ARCH_LEDS=y +CONFIG_ARCH_BUTTONS=y +CONFIG_DRAM_SIZE=0x00010000 +CONFIG_DRAM_START=0x20000000 +CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE) +CONFIG_ARCH_INTERRUPTSTACK=0 +CONFIG_ARCH_STACKDUMP=y + +# +# STR71x specific boot/build settings +# +# CONFIG_STR71X_I2C0, CONFIG_STR71X_I2C1, CONFIG_STR71X_UART0, CONFIG_STR71X_UART1, +# CONFIG_STR71X_UART2, CONFIG_STR71X_UART3, CONFIG_STR71X_USB, CONFIG_STR71X_CAN, +# CONFIG_STR71X_BSPI0, CONFIG_STR71X_BSPI1, CONFIG_STR71X_HDLC, CONFIG_STR71X_XTI, +# CONFIG_STR71X_GPIO0, CONFIG_STR71X_GPIO1, CONFIG_STR71X_GPIO2, CONFIG_STR71X_ADC12, +# CONFIG_STR71X_CKOUT, CONFIG_STR71X_TIM1, CONFIG_STR71X_TIM2, CONFIG_STR71X_TIM3, and +# CONFIG_STR71X_RTC +# Select peripherals to initialize (Timer0 and EIC are always initialized) +# CONFIG_STR71X_BANK0, CONFIG_STR71X_BANK1, CONFIG_STR71X_BANK2, and CONFIG_STR71X_BANK3 +# Enable initialize of external memory banks 0-3. +# CONFIG_STR71X_BANK0_SIZE, CONFIG_STR71X_BANK1_SIZE, CONFIG_STR71X_BANK2_SIZE, and +# CONFIG_STR71X_BANK3_SIZE +# If a particular external memory bank is configured, then its width must be provided. +# 8 and 16 (bits) are the only valid options. +# CONFIG_STR71X_BANK0_WAITSTATES, CONFIG_STR71X_BANK1_WAITSTATES, +# CONFIG_STR71X_BANK2_WAITSTATES, and CONFIG_STR71X_BANK3_WAITSTATES +# If a particular external memory bank is configured, then the number of waistates +# for the bank must also be provided. Valid options are {0, .., 15} +# CONFIG_STR71X_BIGEXTMEM +# The default is to provide 20 bits of address for all external memory regions. If +# any memory region is larger than 1Mb, then this option should be selected. In this +# case, 24 bits of addressing will be used +CONFIG_STR71X_I2C0=n +CONFIG_STR71X_I2C1=n +CONFIG_STR71X_UART0=y +CONFIG_STR71X_UART1=y +CONFIG_STR71X_UART2=n +CONFIG_STR71X_UART3=n +CONFIG_STR71X_USB=n +CONFIG_STR71X_CAN=n +CONFIG_STR71X_BSPI0=n +CONFIG_STR71X_BSPI1=n +CONFIG_STR71X_HDLC=n +CONFIG_STR71X_XTI=n +CONFIG_STR71X_GPIO0=y +CONFIG_STR71X_GPIO1=y +CONFIG_STR71X_GPIO2=n +CONFIG_STR71X_ADC12=n +CONFIG_STR71X_CKOUT=n +CONFIG_STR71X_TIM1=n +CONFIG_STR71X_TIM2=n +CONFIG_STR71X_TIM3=n +CONFIG_STR71X_RTC=n +CONFIG_STR71X_BANK0=n +CONFIG_STR71X_BANK0_SIZE=16 +CONFIG_STR71X_BANK0_WAITSTATES=0 +CONFIG_STR71X_BANK1=n +CONFIG_STR71X_BANK0_SIZE=16 +CONFIG_STR71X_BANK1_WAITSTATES=0 +CONFIG_STR71X_BANK2=n +CONFIG_STR71X_BANK0_SIZE=16 +CONFIG_STR71X_BANK3_WAITSTATES=0 +CONFIG_STR71X_BANK3=n +CONFIG_STR71X_BANK0_SIZE=16 +CONFIG_STR71X_BANK2_WAITSTATES=0 +CONFIG_STR71X_BIGEXTMEM=n + +# +# STR71x specific device driver settings +# +# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the +# console and ttys0 (default is the UART0). +# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. +# This specific the size of the receive buffer +# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before +# being sent. This specific the size of the transmit buffer +# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be +# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. +# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity, 3=mark 1, 4=space 0 +# CONFIG_UARTn_2STOP - Two stop bits +# +CONFIG_UART0_SERIAL_CONSOLE=y +CONFIG_UART1_SERIAL_CONSOLE=n +CONFIG_UART2_SERIAL_CONSOLE=n +CONFIG_UART3_SERIAL_CONSOLE=n +CONFIG_UART0_TXBUFSIZE=256 +CONFIG_UART1_TXBUFSIZE=256 +CONFIG_UART2_TXBUFSIZE=256 +CONFIG_UART3_TXBUFSIZE=256 +CONFIG_UART0_RXBUFSIZE=256 +CONFIG_UART1_RXBUFSIZE=256 +CONFIG_UART2_RXBUFSIZE=256 +CONFIG_UART3_RXBUFSIZE=256 +CONFIG_UART0_BAUD=38400 +CONFIG_UART1_BAUD=38400 +CONFIG_UART2_BAUD=38400 +CONFIG_UART3_BAUD=38400 +CONFIG_UART0_BITS=8 +CONFIG_UART1_BITS=8 +CONFIG_UART2_BITS=8 +CONFIG_UART3_BITS=8 +CONFIG_UART0_PARITY=0 +CONFIG_UART1_PARITY=0 +CONFIG_UART2_PARITY=0 +CONFIG_UART3_PARITY=0 +CONFIG_UART0_2STOP=0 +CONFIG_UART1_2STOP=0 +CONFIG_UART2_2STOP=0 +CONFIG_UART3_2STOP=0 + +# +# General build options +# +# CONFIG_RRLOAD_BINARY - make the rrload binary format used with +# BSPs from www.ridgerun.com using the tools/mkimage.sh script +# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_RAW_BINARY - make a raw binary format file used with many +# different loaders using the GNU objcopy program. This option +# should not be selected if you are not using the GNU toolchain. +# CONFIG_HAVE_LIBM - toolchain supports libm.a +# +CONFIG_RRLOAD_BINARY=n +CONFIG_INTELHEX_BINARY=n +CONFIG_RAW_BINARY=y +CONFIG_HAVE_LIBM=n + +# +# General OS setup +# +# CONFIG_EXAMPLE - identifies the subdirectory in examples +# that will be used in the build +# CONFIG_DEBUG - enables built-in debug options +# CONFIG_DEBUG_VERBOSE - enables verbose debug output +# CONFIG_DEBUG_SYMBOLS - build without optimization and with +# debug symbols (needed for use with a debugger). +# CONFIG_MM_REGIONS - If the architecture includes multiple +# regions of memory to allocate from, this specifies the +# number of memory regions that the memory manager must +# handle and enables the API mm_addregion(start, end); +# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot +# time console output +# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz +# or TICKS_PER_MSEC=10. This setting may be defined to +# inform NuttX that the processor hardware is providing +# system timer interrupts at some interrupt interval other +# than 10 msec. +# CONFIG_RR_INTERVAL - The round robin timeslice will be set +# this number of milliseconds; Round robin scheduling can +# be disabled by setting this value to zero. +# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in +# scheduler to monitor system performance +# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a +# task name to save in the TCB. Useful if scheduler +# instrumentation is selected. Set to zero to disable. +# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - +# Used to initialize the internal time logic. +# CONFIG_JULIAN_TIME - Enables Julian time conversions +# CONFIG_DEV_CONSOLE - Set if architecture-specific logic +# provides /dev/console. Enables stdout, stderr, stdin. +# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console +# driver (minimul support) +# CONFIG_MUTEX_TYPES: Set to enable support for recursive and +# errorcheck mutexes. Enables pthread_mutexattr_settype(). +# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority +# inheritance on mutexes and semaphores. +# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority +# inheritance is enabled. It defines the maximum number of +# different threads (minus one) that can take counts on a +# semaphore with priority inheritance support. This may be +# set to zero if priority inheritance is disabled OR if you +# are only using semaphores as mutexes (only one holder) OR +# if no more than two threads participate using a counting +# semaphore. +# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, +# then this setting is the maximum number of higher priority +# threads (minus 1) than can be waiting for another thread +# to release a count on a semaphore. This value may be set +# to zero if no more than one thread is expected to wait for +# a semaphore. +# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors +# by task_create() when a new task is started. If set, all +# files/drivers will appear to be closed in the new task. +# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first +# three file descriptors (stdin, stdout, stderr) by task_create() +# when a new task is started. If set, all files/drivers will +# appear to be closed in the new task except for stdin, stdout, +# and stderr. +# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket +# desciptors by task_create() when a new task is started. If +# set, all sockets will appear to be closed in the new task. +# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. +# This format will support execution of NuttX binaries located +# in a ROMFS filesystem (see examples/nxflat). +# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to +# handle delayed processing from interrupt handlers. This feature +# is required for some drivers but, if there are not complaints, +# can be safely disabled. The worker thread also performs +# garbage collection -- completing any delayed memory deallocations +# from interrupt handlers. If the worker thread is disabled, +# then that clean will be performed by the IDLE thread instead +# (which runs at the lowest of priority and may not be appropriate +# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE +# is enabled, then the following options can also be used: +# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker +# thread. Default: 50 +# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for +# work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker +# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up +# the worker thread. Default: 4 +# +CONFIG_EXAMPLE=nettest +CONFIG_DEBUG=n +CONFIG_DEBUG_VERBOSE=n +CONFIG_DEBUG_SYMBOLS=n +CONFIG_DEBUG_NET=n +CONFIG_MM_REGIONS=1 +CONFIG_ARCH_LOWPUTC=y +CONFIG_RR_INTERVAL=0 +CONFIG_SCHED_INSTRUMENTATION=n +CONFIG_TASK_NAME_SIZE=0 +CONFIG_START_YEAR=2010 +CONFIG_START_MONTH=5 +CONFIG_START_DAY=1 +CONFIG_JULIAN_TIME=n +CONFIG_DEV_CONSOLE=y +CONFIG_DEV_LOWCONSOLE=y +CONFIG_MUTEX_TYPES=n +CONFIG_PRIORITY_INHERITANCE=n +CONFIG_SEM_PREALLOCHOLDERS=0 +CONFIG_SEM_NNESTPRIO=0 +CONFIG_FDCLONE_DISABLE=n +CONFIG_FDCLONE_STDIO=n +CONFIG_SDCLONE_DISABLE=y +CONFIG_NXFLAT=n +CONFIG_SCHED_WORKQUEUE=y +CONFIG_SCHED_WORKPRIORITY=50 +CONFIG_SCHED_WORKPERIOD=(50*1000) +CONFIG_SCHED_WORKSTACKSIZE=1024 +CONFIG_SIG_SIGWORK=4 + +# +# The following can be used to disable categories of +# APIs supported by the OS. If the compiler supports +# weak functions, then it should not be necessary to +# disable functions unless you want to restrict usage +# of those APIs. +# +# There are certain dependency relationships in these +# features. +# +# o mq_notify logic depends on signals to awaken tasks +# waiting for queues to become full or empty. +# o pthread_condtimedwait() depends on signals to wake +# up waiting tasks. +# +CONFIG_DISABLE_CLOCK=n +CONFIG_DISABLE_POSIX_TIMERS=n +CONFIG_DISABLE_PTHREAD=n +CONFIG_DISABLE_SIGNALS=n +CONFIG_DISABLE_MQUEUE=n +CONFIG_DISABLE_MOUNTPOINT=y +CONFIG_DISABLE_ENVIRON=y +CONFIG_DISABLE_POLL=y + +# +# Misc libc settings +# +# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a +# little smaller if we do not support fieldwidthes +# +CONFIG_NOPRINTF_FIELDWIDTH=n + +# +# Allow for architecture optimized implementations +# +# The architecture can provide optimized versions of the +# following to improve sysem performance +# +CONFIG_ARCH_MEMCPY=n +CONFIG_ARCH_MEMCMP=n +CONFIG_ARCH_MEMMOVE=n +CONFIG_ARCH_MEMSET=n +CONFIG_ARCH_STRCMP=n +CONFIG_ARCH_STRCPY=n +CONFIG_ARCH_STRNCPY=n +CONFIG_ARCH_STRLEN=n +CONFIG_ARCH_BZERO=n +CONFIG_ARCH_KMALLOC=n +CONFIG_ARCH_KZMALLOC=n +CONFIG_ARCH_KFREE=n + +# +# Sizes of configurable things (0 disables) +# +# CONFIG_MAX_TASKS - The maximum number of simultaneously +# active tasks. This value must be a power of two. +# CONFIG_MAX_TASK_ARGS - This controls the maximum number of +# of parameters that a task may receive (i.e., maxmum value +# of 'argc') +# CONFIG_NPTHREAD_KEYS - The number of items of thread- +# specific data that can be retained +# CONFIG_NFILE_DESCRIPTORS - The maximum number of file +# descriptors (one for each open) +# CONFIG_NFILE_STREAMS - The maximum number of streams that +# can be fopen'ed +# CONFIG_NAME_MAX - The maximum size of a file name. +# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate +# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_NUNGET_CHARS - Number of characters that can be +# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message +# structures. The system manages a pool of preallocated +# message structures to minimize dynamic allocations +# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with +# a fixed payload size given by this settin (does not include +# other message structure overhead. +# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that +# can be passed to a watchdog handler +# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog +# structures. The system manages a pool of preallocated +# watchdog structures to minimize dynamic allocations +# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX +# timer structures. The system manages a pool of preallocated +# timer structures to minimize dynamic allocations. Set to +# zero for all dynamic allocations. +# +CONFIG_MAX_TASKS=16 +CONFIG_MAX_TASK_ARGS=4 +CONFIG_NPTHREAD_KEYS=4 +CONFIG_NFILE_DESCRIPTORS=8 +CONFIG_NFILE_STREAMS=8 +CONFIG_NAME_MAX=32 +CONFIG_STDIO_BUFFER_SIZE=256 +CONFIG_NUNGET_CHARS=2 +CONFIG_PREALLOC_MQ_MSGS=4 +CONFIG_MQ_MAXMSGSIZE=32 +CONFIG_MAX_WDOGPARMS=2 +CONFIG_PREALLOC_WDOGS=4 +CONFIG_PREALLOC_TIMERS=4 + +# +# Filesystem configuration +# +# CONFIG_FS_FAT - Enable FAT filesystem support +# CONFIG_FAT_SECTORSIZE - Max supported sector size +# CONFIG_FS_ROMFS - Enable ROMFS filesystem support +CONFIG_FS_FAT=n +CONFIG_FS_ROMFS=n + +# +# ENC28J60 configuration +# +# CONFIG_NET_ENC28J60 - Enabled ENC28J60 support +# CONFIG_ENC28J60_OWNBUS - Set if the ENC28J60 is the only active device on +# the SPI bus. No locking or SPI configuration will be performed. All +# transfers will be performed from the ENC2J60 interrupt handler. +# CONFIG_ENC28J60_SPIMODE - Controls the SPI mode +# CONFIG_ENC28J60_FREQUENCY - Define to use a different bus frequency +# CONFIG_ENC28J60_NINTERFACES - Specifies the number of physical ENC28J60 +# devices that will be supported. +# CONFIG_ENC28J60_STATS - Collect network statistics +# CONFOG_ENC28J60_HALFDUPPLEX - Default is full duplex +CONFIG_NET_ENC28J60=y +CONFIG_ENC28J60_OWNBUS=n +#CONFIG_ENC28J60_SPIMODE +CONFIG_ENC28J60_FREQUENCY=20000000 +CONFIG_ENC28J60_NINTERFACES=1 +CONFIG_ENC28J60_STATS=y +CONFIG_ENC28J60_HALFDUPPLEX=n + +# +# SPI-based MMC/SD driver +# +# CONFIG_MMCSD_NSLOTS +# Number of MMC/SD slots supported by the driver +# CONFIG_MMCSD_READONLY +# Provide read-only access (default is read/write) +CONFIG_MMCSD_NSLOTS=1 +CONFIG_MMCSD_READONLY=n + +# +# TCP/IP and UDP support via uIP +# CONFIG_NET - Enable or disable all network features +# CONFIG_NET_IPv6 - Build in support for IPv6 +# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. +# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options +# CONFIG_NET_BUFSIZE - uIP buffer size +# CONFIG_NET_TCP - TCP support on or off +# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) +# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers +# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) +# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until +# accept() is called. The size of the backlog is selected when listen() is called. +# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) +# CONFIG_NET_UDP - UDP support on or off +# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off +# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections +# CONFIG_NET_ICMP - ICMP ping response support on or off +# CONFIG_NET_ICMP_PING - ICMP ping request support on or off +# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address +# CONFIG_NET_STATISTICS - uIP statistics on or off +# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window +# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table +# CONFIG_NET_BROADCAST - Broadcast support +# CONFIG_NET_LLH_LEN - The link level header length +# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates +CONFIG_NET=y +CONFIG_NET_IPv6=n +CONFIG_NSOCKET_DESCRIPTORS=8 +CONFIG_NET_SOCKOPTS=y +CONFIG_NET_BUFSIZE=420 +CONFIG_NET_TCP=y +CONFIG_NET_TCP_CONNS=8 +CONFIG_NET_NTCP_READAHEAD_BUFFERS=8 +CONFIG_NET_TCPBACKLOG=n +CONFIG_NET_MAX_LISTENPORTS=8 +CONFIG_NET_UDP=n +CONFIG_NET_UDP_CHECKSUMS=y +#CONFIG_NET_UDP_CONNS=10 +CONFIG_NET_ICMP=y +CONFIG_NET_ICMP_PING=n +#CONFIG_NET_PINGADDRCONF=0 +CONFIG_NET_STATISTICS=y +#CONFIG_NET_RECEIVE_WINDOW= +#CONFIG_NET_ARPTAB_SIZE=8 +CONFIG_NET_BROADCAST=n +#CONFIG_NET_LLH_LEN=14 +#CONFIG_NET_FWCACHE_SIZE=2 + +# +# UIP Network Utilities +# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP +# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries +CONFIG_NET_DHCP_LIGHT=n +CONFIG_NET_RESOLV_ENTRIES=4 + +# +# USB Device Configuration +# +# CONFIG_USBDEV +# Enables USB device support +# CONFIG_USBDEV_ISOCHRONOUS +# Build in extra support for isochronous endpoints +# CONFIG_USBDEV_DUALSPEED +# Hardware handles high and full speed operation (USB 2.0) +# CONFIG_USBDEV_SELFPOWERED +# Will cause USB features to indicate that the device is +# self-powered +# CONFIG_USBDEV_MAXPOWER +# Maximum power consumption in mA +# CONFIG_USBDEV_TRACE +# Enables USB tracing for debug +# CONFIG_USBDEV_TRACE_NRECORDS +# Number of trace entries to remember +CONFIG_USBDEV=n +CONFIG_USBDEV_ISOCHRONOUS=n +CONFIG_USBDEV_DUALSPEED=n +CONFIG_USBDEV_SELFPOWERED=y +CONFIG_USBDEV_REMOTEWAKEUP=n +CONFIG_USBDEV_MAXPOWER=100 +CONFIG_USBDEV_TRACE=n +CONFIG_USBDEV_TRACE_NRECORDS=128 + +# +# STR71X USB Configuration +# +# CONFIG_STR71X_USBDEV_FRAME_INTERRUPT +# Handle USB Start-Of-Frame events. +# Enable reading SOF from interrupt handler vs. simply reading on demand. +# Probably a bad idea... Unless there is some issue with sampling the SOF +# from hardware asynchronously. +# CONFIG_STR71X_USBDEV_EPFAST_INTERRUPT +# Enable high priority interrupts. I have no idea why you might want to +# do that +# CONFIG_STR71X_USBDEV_NDMADESCRIPTORS +# Number of DMA descriptors to allocate in the 8Kb USB RAM. This is a +# tradeoff between the number of DMA channels that can be supported vs +# the size of the DMA buffers available. +# CONFIG_STR71X_USBDEV_DMA +# Enable str71x-specific DMA support +CONFIG_STR71X_USBDEV_FRAME_INTERRUPT=n +CONFIG_STR71X_USBDEV_EPFAST_INTERRUPT=n +CONFIG_STR71X_USBDEV_DMA=n +CONFIG_STR71X_USBDEV_NDMADESCRIPTORS=0 +CONFIG_STR71X_USBDEV_DMAINTMASK=0 + +# +# USB Serial Device Configuration +# +# CONFIG_USBSER +# Enable compilation of the USB serial driver +# CONFIG_USBSER_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation +# CONFIG_USBSER_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation +# CONFIG_USBSER_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation +# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR +# The vendor ID code/string +# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR +# The product ID code/string +# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE +# Size of the serial receive/transmit buffers +CONFIG_USBSER=n +CONFIG_USBSER_EPINTIN=1 +CONFIG_USBSER_EPBULKOUT=2 +CONFIG_USBSER_EPBULKIN=5 +CONFIG_USBSER_NWRREQS=4 +CONFIG_USBSER_NRDREQS=4 +CONFIG_USBSER_VENDORID=0x067b +CONFIG_USBSER_PRODUCTID=0x2303 +CONFIG_USBSER_VENDORSTR="Nuttx" +CONFIG_USBSER_PRODUCTSTR="USBdev Serial" +CONFIG_USBSER_RXBUFSIZE=512 +CONFIG_USBSER_TXBUFSIZE=512 + +# +# USB Storage Device Configuration +# +# CONFIG_USBSTRG +# Enable compilation of the USB storage driver +# CONFIG_USBSTRG_EP0MAXPACKET +# Max packet size for endpoint 0 +# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN +# The logical 7-bit address of a hardware endpoints that support +# bulk OUT and IN operations +# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN +# The size of the buffer in each write/read request. This +# value needs to be at least as large as the endpoint +# maxpacket and ideally as large as a block device sector. +# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR +# The vendor ID code/string +# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR +# The product ID code/string +# CONFIG_USBSTRG_REMOVABLE +# Select if the media is removable +CONFIG_USBSTRG=n +CONFIG_USBSTRG_EP0MAXPACKET=64 +CONFIG_USBSTRG_EPBULKOUT=2 +CONFIG_USBSTRG_EPBULKIN=5 +CONFIG_USBSTRG_NRDREQS=2 +CONFIG_USBSTRG_NWRREQS=2 +CONFIG_USBSTRG_BULKINREQLEN=256 +CONFIG_USBSTRG_BULKOUTREQLEN=256 +CONFIG_USBSTRG_VENDORID=0x584e +CONFIG_USBSTRG_VENDORSTR="NuttX" +CONFIG_USBSTRG_PRODUCTID=0x5342 +CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage" +CONFIG_USBSTRG_VERSIONNO=0x0399 +CONFIG_USBSTRG_REMOVABLE=y + +# +# Settings for examples/nettest +# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act +# as either the client side or server side of the test +# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the +# client side simply receives messages forever, allowing +# measurement of throughput +# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has +# no MAC address; one will be assigned +# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address +# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address +# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask +# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the +# client side of the test (may be target or host) +CONFIG_EXAMPLE_NETTEST_SERVER=n +CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n +CONFIG_EXAMPLE_NETTEST_NOMAC=y +CONFIG_EXAMPLE_NETTEST_IPADDR=(10L<<24|0L<<16|0L<<8|2L) +CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L) +CONFIG_EXAMPLE_NETTEST_NETMASK=(255L<<24|255L<<16|255L<<8|0L) +CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10L<<24|0L<<16|0L<<8|1L) + +# +# Settings for examples/ostest +CONFIG_EXAMPLES_OSTEST_LOOPS=1 +CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048 +CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 + +# +# Settings for examples/nsh +# +# CONFIG_EXAMPLES_NSH_FILEIOSIZE - Size of a static I/O buffer +# CONFIG_EXAMPLES_NSH_STRERROR - Use strerror(errno) +# CONFIG_EXAMPLES_NSH_LINELEN - Maximum length of one command line +# CONFIG_EXAMPLES_NSH_STACKSIZE - Stack size to use for new threads. +# CONFIG_EXAMPLES_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi +# CONFIG_EXAMPLES_NSH_DISABLESCRIPT - Disable scripting support +# CONFIG_EXAMPLES_NSH_DISABLEBG - Disable background commands +# CONFIG_EXAMPLES_NSH_ROMFSETC - Use startup script in /etc +# CONFIG_EXAMPLES_NSH_CONSOLE - Use serial console front end +# CONFIG_EXAMPLES_NSH_TELNET - Use telnetd console front end +# CONFIG_EXAMPLES_NSH_ARCHINIT - Platform provides architecture +# specific initialization (nsh_archinitialize()). +# +# If CONFIG_EXAMPLES_NSH_TELNET is selected: +# CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size +# CONFIG_EXAMPLES_NSH_DHCPC - Obtain address using DHCP +# CONFIG_EXAMPLES_NSH_IPADDR - Provides static IP address +# CONFIG_EXAMPLES_NSH_DRIPADDR - Provides static router IP address +# CONFIG_EXAMPLES_NSH_NETMASK - Provides static network mask +# CONFIG_EXAMPLES_NSH_NOMAC - Use a bogus MAC address +# +# If CONFIG_EXAMPLES_NSH_ROMFSETC is selected: +# CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT - ROMFS mountpoint +# CONFIG_EXAMPLES_NSH_INITSCRIPT - Relative path to init script +# CONFIG_EXAMPLES_NSH_ROMFSDEVNO - ROMFS RAM device minor +# CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE - ROMF sector size +# CONFIG_EXAMPLES_NSH_FATDEVNO - FAT FS RAM device minor +# CONFIG_EXAMPLES_NSH_FATSECTSIZE - FAT FS sector size +# CONFIG_EXAMPLES_NSH_FATNSECTORS - FAT FS number of sectors +# CONFIG_EXAMPLES_NSH_FATMOUNTPT - FAT FS mountpoint +# +CONFIG_EXAMPLES_NSH_FILEIOSIZE=512 +CONFIG_EXAMPLES_NSH_STRERROR=n +CONFIG_EXAMPLES_NSH_LINELEN=64 +CONFIG_EXAMPLES_NSH_STACKSIZE=2048 +CONFIG_EXAMPLES_NSH_NESTDEPTH=3 +CONFIG_EXAMPLES_NSH_DISABLESCRIPT=n +CONFIG_EXAMPLES_NSH_DISABLEBG=n +CONFIG_EXAMPLES_NSH_ROMFSETC=n +CONFIG_EXAMPLES_NSH_CONSOLE=y +CONFIG_EXAMPLES_NSH_TELNET=n +CONFIG_EXAMPLES_NSH_ARCHINIT=n +CONFIG_EXAMPLES_NSH_IOBUFFER_SIZE=512 +CONFIG_EXAMPLES_NSH_DHCPC=n +CONFIG_EXAMPLES_NSH_NOMAC=n +CONFIG_EXAMPLES_NSH_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLES_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLES_NSH_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLES_NSH_ROMFSMOUNTPT="/etc" +CONFIG_EXAMPLES_NSH_INITSCRIPT="init.d/rcS" +CONFIG_EXAMPLES_NSH_ROMFSDEVNO=0 +CONFIG_EXAMPLES_NSH_ROMFSSECTSIZE=64 +CONFIG_EXAMPLES_NSH_FATDEVNO=1 +CONFIG_EXAMPLES_NSH_FATSECTSIZE=512 +CONFIG_EXAMPLES_NSH_FATNSECTORS=1024 +CONFIG_EXAMPLES_NSH_FATMOUNTPT=/tmp + +# +# Architecture-specific NSH options +CONFIG_EXAMPLES_NSH_MMCSDSPIPORTNO=1 +CONFIG_EXAMPLES_NSH_MMCSDSLOTNO=0 +CONFIG_EXAMPLES_NSH_MMCSDMINOR=0 + +# +# Stack and heap information +# +# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP +# operation from FLASH but must copy initialized .data sections to RAM. +# (This option does not appy to the STR71x -- it always runs from flash). +# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH +# but copy themselves entirely into RAM for better performance. +# (This option does not appy to the STR71x -- it is never copied to RAM). +# CONFIG_CUSTOM_STACK - The up_ implementation will handle +# all stack operations outside of the nuttx model. +# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) +# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. +# This is the thread that (1) performs the inital boot of the system up +# to the point where user_start() is spawned, and (2) there after is the +# IDLE thread that executes only when there is no other thread ready to +# run. +# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate +# for the main user thread that begins at the user_start() entry point. +# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size +# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size +# CONFIG_HEAP_BASE - The beginning of the heap +# CONFIG_HEAP_SIZE - The size of the heap +# +CONFIG_BOOT_RUNFROMFLASH=n +CONFIG_BOOT_COPYTORAM=n +CONFIG_CUSTOM_STACK=n +CONFIG_STACK_POINTER= +CONFIG_IDLETHREAD_STACKSIZE=2048 +CONFIG_USERMAIN_STACKSIZE=2048 +CONFIG_PTHREAD_STACK_MIN=256 +CONFIG_PTHREAD_STACK_DEFAULT=2048 +CONFIG_HEAP_BASE= +CONFIG_HEAP_SIZE= diff --git a/nuttx/configs/olimex-strp711/nettest/ld.script b/nuttx/configs/olimex-strp711/nettest/ld.script new file mode 100755 index 000000000..4d91c5c75 --- /dev/null +++ b/nuttx/configs/olimex-strp711/nettest/ld.script @@ -0,0 +1,122 @@ +/**************************************************************************** + * configs/olimex-strp711/nettest/ld.script + * + * Copyright (C) 2010 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The str71x has 256Kb of non-volatile memory beginning at address + * 0x4000:0000 for program storage (Bank0, an addition 16Kb is available + * for data storage in Bank1). The OS entry point is via the reset vector + * at address 0x00000000 where the FLASH is remapped at reset. + * + * The str71x has 64Kb of on-chip static RAM beginning at address + * 0x2000:0000. The .data section will be relocated from _eronly + * to _sdata at boot time. + */ + +/* The STR711 has 256Kb of FLASH beginning at address 0x4000:0000 and 64Kb + * of SRAM beginning at address 0x2000:0000 + */ + +MEMORY +{ + flash (rx) : ORIGIN = 0x40000000, LENGTH = 256K + sram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K +} + +OUTPUT_ARCH(arm) +ENTRY(_stext) +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.glue_7) + *(.glue_7t) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + } > flash + + /* This is where the .data section is relocated for execution out + * FLASH. The .data section will be relocated from _eronly + * to _sdata at boot time. + */ + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .ARM.extab : { + *(.ARM.extab*) + } >sram + + .ARM.exidx : { + __exidx_start = ABSOLUTE(.); + *(.ARM.exidx*) + __exidx_end = ABSOLUTE(.); + } >sram + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/nuttx/configs/olimex-strp711/nettest/setenv.sh b/nuttx/configs/olimex-strp711/nettest/setenv.sh new file mode 100755 index 000000000..419731319 --- /dev/null +++ b/nuttx/configs/olimex-strp711/nettest/setenv.sh @@ -0,0 +1,47 @@ +#!/bin/bash +# configs/olimex-strp711/nettest/setenv.sh +# +# Copyright (C) 2010 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# + +if [ "$(basename $0)" = "setenv.sh" ] ; then + echo "You must source this script, not run it!" 1>&2 + exit 1 +fi + +if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi + +WD=`pwd` +export BUILDROOT_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin" +export STR41XSCRIPTS="$WD/configs/olimex-strp711/scripts" +export PATH="${BUILDROOT_BIN}:${STR41XSCRIPTS}:/sbin:/usr/sbin:${PATH_ORIG}" + +echo "PATH : ${PATH}" -- cgit v1.2.3