From 15adeb9273b237f0168ef0d63b5304e7bcb95d02 Mon Sep 17 00:00:00 2001
From: patacongo <patacongo@42af7a65-404d-4744-a932-0658087f49c3>
Date: Sun, 7 Feb 2010 15:29:04 +0000
Subject: Remove some STM32-isms and SPI support

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2536 42af7a65-404d-4744-a932-0658087f49c3
---
 nuttx/configs/sam3u-ek/src/up_nsh.c | 63 ++++++-------------------------------
 1 file changed, 10 insertions(+), 53 deletions(-)

(limited to 'nuttx/configs/sam3u-ek')

diff --git a/nuttx/configs/sam3u-ek/src/up_nsh.c b/nuttx/configs/sam3u-ek/src/up_nsh.c
index 1049a9bf7..c8370369c 100755
--- a/nuttx/configs/sam3u-ek/src/up_nsh.c
+++ b/nuttx/configs/sam3u-ek/src/up_nsh.c
@@ -2,7 +2,7 @@
  * config/sam3u-ek/src/up_nsh.c
  * arch/arm/src/board/up_nsh.c
  *
- *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
+ *   Copyright (C) 2010 Gregory Nutt. All rights reserved.
  *   Author: Gregory Nutt <spudmonkey@racsa.co.cr>
  *
  * Redistribution and use in source and binary forms, with or without
@@ -45,18 +45,13 @@
 #include <debug.h>
 #include <errno.h>
 
-#ifdef CONFIG_SAM3U_SPI1
-#  include <nuttx/spi.h>
-#  include <nuttx/mtd.h>
-#endif
-
-#ifdef CONFIG_SAM3U_SDIO
-#  include <nuttx/sdio.h>
-#  include <nuttx/mmcsd.h>
-#endif
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
 
 #include "sam3u_internal.h"
 
+#ifdef CONFIG_SAM3U_HSMCI
+
 /****************************************************************************
  * Pre-Processor Definitions
  ****************************************************************************/
@@ -65,7 +60,7 @@
 
 /* PORT and SLOT number probably depend on the board configuration */
 
-#ifdef CONFIG_ARCH_BOARD_SAM3U_EK
+#ifdef CONFIG_ARCH_BOARD_SAM3UEK
 #  define CONFIG_EXAMPLES_NSH_HAVEUSBDEV 1
 #  define CONFIG_EXAMPLES_NSH_HAVEMMCSD  1
 #  if defined(CONFIG_EXAMPLES_NSH_MMCSDSLOTNO) && CONFIG_EXAMPLES_NSH_MMCSDSLOTNO != 0
@@ -92,7 +87,7 @@
  * is not enabled.
  */
 
-#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_SAM3U_SDIO)
+#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_SAM3U_HSMCI)
 #  undef CONFIG_EXAMPLES_NSH_HAVEMMCSD
 #endif
 
@@ -130,50 +125,11 @@
 
 int nsh_archinitialize(void)
 {
-#ifdef CONFIG_SAM3U_SPI1
-  FAR struct spi_dev_s *spi;
-  FAR struct mtd_dev_s *mtd;
-#endif
 #ifdef CONFIG_EXAMPLES_NSH_HAVEMMCSD
   FAR struct sdio_dev_s *sdio;
   int ret;
-#endif
-
-  /* Configure SPI-based devices */
-
-#ifdef CONFIG_SAM3U_SPI1
-  /* Get the SPI port */
-
-  message("nsh_archinitialize: Initializing SPI port 0\n");
-  spi = up_spiinitialize(0);
-  if (!spi)
-    {
-      message("nsh_archinitialize: Failed to initialize SPI port 0\n");
-      return -ENODEV;
-    }
-  message("nsh_archinitialize: Successfully initialized SPI port 0\n");
-
-  /* Now bind the SPI interface to the M25P64/128 SPI FLASH driver */
-
-  message("nsh_archinitialize: Bind SPI to the SPI flash driver\n");
-  mtd = m25p_initialize(spi);
-  if (!mtd)
-    {
-      message("nsh_archinitialize: Failed to bind SPI port 0 to the SPI FLASH driver\n");
-      return -ENODEV;
-    }
-  message("nsh_archinitialize: Successfully bound SPI port 0 to the SPI FLASH driver\n");
-#warning "Now what are we going to do with this SPI FLASH driver?"
-#endif
-
-  /* Create the SPI FLASH MTD instance */
-  /* The M25Pxx is not a give media to implement a file system..
-   * its block sizes are too large
-   */
 
   /* Mount the SDIO-based MMC/SD block driver */
-
-#ifdef CONFIG_EXAMPLES_NSH_HAVEMMCSD
   /* First, get an instance of the SDIO interface */
 
   message("nsh_archinitialize: Initializing SDIO slot %d\n",
@@ -186,7 +142,7 @@ int nsh_archinitialize(void)
       return -ENODEV;
     }
 
-  /* Now bind the SPI interface to the MMC/SD driver */
+  /* Now bind the SDIO interface to the MMC/SD driver */
 
   message("nsh_archinitialize: Bind SDIO to the MMC/SD driver, minor=%d\n",
           CONFIG_EXAMPLES_NSH_MMCSDMINOR);
@@ -199,7 +155,7 @@ int nsh_archinitialize(void)
   message("nsh_archinitialize: Successfully bound SDIO to the MMC/SD driver\n");
   
   /* Then let's guess and say that there is a card in the slot.  I need to check to
-   * see if the SAM3U10E-EVAL board supports a GPIO to detect if there is a card in
+   * see if the SAM3U-EK board supports a GPIO to detect if there is a card in
    * the slot.
    */
 
@@ -207,3 +163,4 @@ int nsh_archinitialize(void)
 #endif
   return OK;
 }
+#endif
-- 
cgit v1.2.3