From 05738115218b3090bce9e5e3e279e0a9f5df194d Mon Sep 17 00:00:00 2001 From: patacongo Date: Tue, 29 May 2012 00:54:22 +0000 Subject: Massive naming fix: STMPE11->STMPE811 git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4782 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/configs/stm3240g-eval/nxwm/defconfig | 72 +++++++++++++++--------------- 1 file changed, 36 insertions(+), 36 deletions(-) (limited to 'nuttx/configs/stm3240g-eval/nxwm') diff --git a/nuttx/configs/stm3240g-eval/nxwm/defconfig b/nuttx/configs/stm3240g-eval/nxwm/defconfig index c449042e6..38739b35b 100644 --- a/nuttx/configs/stm3240g-eval/nxwm/defconfig +++ b/nuttx/configs/stm3240g-eval/nxwm/defconfig @@ -956,66 +956,66 @@ CONFIG_INPUT=y CONFIG_INPUT_TSC2007=n # -# STMPE11 input device configuration +# STMPE811 input device configuration # # Prerequisites: CONFIG_INPUT=y # Other settings that effect the driver: CONFIG_DISABLE_POLL # -# CONFIG_INPUT_STMPE11 -# Enables support for the STMPE11 driver (Needs CONFIG_INPUT) -# CONFIG_STMPE11_SPI +# CONFIG_INPUT_STMPE811 +# Enables support for the STMPE811 driver (Needs CONFIG_INPUT) +# CONFIG_STMPE811_SPI # Enables support for the SPI interface (not currenly supported) -# CONFIG_STMPE11_I2C +# CONFIG_STMPE811_I2C # Enables support for the I2C interface -# CONFIG_STMPE11_MULTIPLE -# Can be defined to support multiple STMPE11 devices on board. -# CONFIG_STMPE11_ACTIVELOW +# CONFIG_STMPE811_MULTIPLE +# Can be defined to support multiple STMPE811 devices on board. +# CONFIG_STMPE811_ACTIVELOW # Interrupt is generated by an active low signal (or falling edge). -# CONFIG_STMPE11_EDGE +# CONFIG_STMPE811_EDGE # Interrupt is generated on an edge (vs. on the active level) -# CONFIG_STMPE11_NPOLLWAITERS +# CONFIG_STMPE811_NPOLLWAITERS # Maximum number of threads that can be waiting on poll() (ignored if # CONFIG_DISABLE_POLL is set). -# CONFIG_STMPE11_TSC_DISABLE +# CONFIG_STMPE811_TSC_DISABLE # Disable driver touchscreen functionality. -# CONFIG_STMPE11_ADC_DISABLE +# CONFIG_STMPE811_ADC_DISABLE # Disable driver ADC functionality. -# CONFIG_STMPE11_GPIO_DISABLE +# CONFIG_STMPE811_GPIO_DISABLE # Disable driver GPIO functionality. -# CONFIG_STMPE11_GPIOINT_DISABLE +# CONFIG_STMPE811_GPIOINT_DISABLE # Disable driver GPIO interrupt functionality (ignored if GPIO functionality is # disabled). -# CONFIG_STMPE11_SWAPXY +# CONFIG_STMPE811_SWAPXY # Reverse the meaning of X and Y to handle different LCD orientations. # For the STM3240G-EVAL, X and Y should be swapped in PORTRAIT modes -# CONFIG_STMPE11_TEMP_DISABLE +# CONFIG_STMPE811_TEMP_DISABLE # Disable driver temperature sensor functionality. -# CONFIG_STMPE11_REGDBUG +# CONFIG_STMPE811_REGDBUG # Enabled very low register-level debug output. Requires CONFIG_DEBUG. -# CONFIG_STMPE11_THRESHX and CONFIG_STMPE11_THRESHY -# STMPE11 touchscreen data comes in a a very high rate. New touch positions +# CONFIG_STMPE811_THRESHX and CONFIG_STMPE811_THRESHY +# STMPE811 touchscreen data comes in a a very high rate. New touch positions # will only be reported when the X or Y data changes by these thresholds. # This trades reduces data rate for some loss in dragging accuracy. The -# STMPE11 is configure for 12-bit values so the raw ranges are 0-4095. So +# STMPE811 is configure for 12-bit values so the raw ranges are 0-4095. So # for example, if your display is 320x240, then THRESHX=13 and THRESHY=17 # would correspond to one pixel. Default: 12 # -CONFIG_INPUT_STMPE11=y -CONFIG_STMPE11_SPI=n -CONFIG_STMPE11_I2C=y -CONFIG_STMPE11_MULTIPLE=y -CONFIG_STMPE11_ACTIVELOW=y -CONFIG_STMPE11_EDGE=y -#CONFIG_STMPE11_NPOLLWAITERS -CONFIG_STMPE11_TSC_DISABLE=n -CONFIG_STMPE11_ADC_DISABLE=y -CONFIG_STMPE11_GPIO_DISABLE=y -CONFIG_STMPE11_GPIOINT_DISABLE=y -CONFIG_STMPE11_SWAPXY=n -CONFIG_STMPE11_TEMP_DISABLE=y -CONFIG_STMPE11_REGDEBUG=n -CONFIG_STMPE11_THRESHX=39 -CONFIG_STMPE11_THRESHY=51 +CONFIG_INPUT_STMPE811=y +CONFIG_STMPE811_SPI=n +CONFIG_STMPE811_I2C=y +CONFIG_STMPE811_MULTIPLE=y +CONFIG_STMPE811_ACTIVELOW=y +CONFIG_STMPE811_EDGE=y +#CONFIG_STMPE811_NPOLLWAITERS +CONFIG_STMPE811_TSC_DISABLE=n +CONFIG_STMPE811_ADC_DISABLE=y +CONFIG_STMPE811_GPIO_DISABLE=y +CONFIG_STMPE811_GPIOINT_DISABLE=y +CONFIG_STMPE811_SWAPXY=n +CONFIG_STMPE811_TEMP_DISABLE=y +CONFIG_STMPE811_REGDEBUG=n +CONFIG_STMPE811_THRESHX=39 +CONFIG_STMPE811_THRESHY=51 # # USB Device Configuration -- cgit v1.2.3