From 20bd3606dbb5c816967a55b07e430a65d2d845a0 Mon Sep 17 00:00:00 2001 From: patacongo Date: Mon, 26 Apr 2010 00:05:50 +0000 Subject: Add PHY register definitions git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2630 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/drivers/net/enc28j60.h | 197 +++++++++++++++++++++++++++++-------------- 1 file changed, 135 insertions(+), 62 deletions(-) (limited to 'nuttx') diff --git a/nuttx/drivers/net/enc28j60.h b/nuttx/drivers/net/enc28j60.h index 9496ee9f7..67bbc5b3a 100755 --- a/nuttx/drivers/net/enc28j60.h +++ b/nuttx/drivers/net/enc28j60.h @@ -44,7 +44,12 @@ * Pre-processor Definitions ****************************************************************************/ -/* A total of seven instructions are implemented on the ENC28J60 */ +/* ENC28J60 Commands ********************************************************/ +/* A total of seven instructions are implemented on the ENC28J60. Where: + * + * aaaaaa is the 5-bit address of a control register, and + * dddddddd is one or more bytes of data that may accompany the command. + */ #define ENC28J60_RCR (0x00) /* Read Control Register * 000 | aaaaa | (Registe value returned)) */ @@ -61,20 +66,21 @@ #define ENC28J60_SRC (0xff) /* System Reset * 111 | 11111 | (No data) */ -/* Control registers are accessed with the RCR, RBM, WCR, BFS, and BFC commands. - * The following identifies all ENC28J60 control registers. The Control register - * memory is partitioned into four banks, selectable by the bank select bits, - * BSEL1:BSEL0, in the ECON1 register. +/* Global Control Registers *************************************************/ +/* Control registers are accessed with the RCR, RBM, WCR, BFS, and BFC + * commands. The following identifies all ENC28J60 control registers. The + * control register memory is partitioned into four banks, selectable by the + * bank select bits, BSEL1:BSEL0, in the ECON1 register. * - * The last five locations (0x1b to 0x1f) of all banks point to a common set of - * registers: EIE, EIR, ESTAT, ECON2 and ECON1. These are key registers used - * in controlling and monitoring the operation of the device. Their common - * mapping allows easy access without switching the bank. + * The last five locations (0x1b to 0x1f) of all banks point to a common set + * of registers: EIE, EIR, ESTAT, ECON2 and ECON1. These are key registers + * usedin controlling and monitoring the operation of the device. Their + * common mapping allows easy access without switching the bank. * * Control registers for the ENC28J60 are generically grouped as ETH, MAC and - * MII registers. Register names starting with E belong to the ETH group. Similarly, - * registers names starting with MA belong to the MAC group and registers prefixed - * with MI belong to the MII group. + * MII registers. Register names starting with E belong to the ETH group. + * Similarly, registers names starting with MA belong to the MAC group and + * registers prefixed with MI belong to the MII group. */ #define EIE (0x1b) /* Ethernet Interrupt Enable Register */ @@ -83,9 +89,66 @@ #define ECON2 (0x1e) /* Ethernet Control 2 Register */ #define ECON1 (0x1f) /* Ethernet Control 1 Register */ -/* The remaining control registers are identified with a a 5 bit address and a - * bank selection. We pack the bank number and the control register address - * together to keep the design simpler. +/* Ethernet Interrupt Enable Register Bit Definitions */ + +#define EIE_RXERIE (1 << 0) /* Bit 0: Receive Error Interrupt Enable */ +#define EIE_TXERIE (1 << 1) /* Bit 1: Transmit Error Interrupt Enable */ + /* Bit 2: Reserved */ +#define EIE_TXIE (1 << 3) /* Bit 3: Transmit Enable */ +#define EIE_LINKIE (1 << 4) /* Bit 4: Link Status Change Interrupt Enable */ +#define EIE_DMAIE (1 << 5) /* Bit 5: DMA Interrupt Enable */ +#define EIE_PKTIE (1 << 6) /* Bit 6: Receive Packet Pending Interrupt Enable */ +#define EIE_INTIE (1 << 7) /* Bit 7: Global INT Interrupt Enable */ + +/* Ethernet Interrupt Request Register Bit Definitions */ + +#define EIR_RXERIF (1 << 0) /* Bit 0: Receive Error Interrupt */ +#define EIR_TXERIF (1 << 1) /* Bit 1: Transmit Error Interrupt */ + /* Bit 2: Reserved */ +#define EIR_TXIF (1 << 3) /* Bit 3: Transmit Interrupt */ +#define EIR_LINKIF (1 << 4) /* Bit 4: Link Change Interrupt */ +#define EIR_DMAIF (1 << 5) /* Bit 5: DMA Interrupt */ +#define EIR_PKTIF (1 << 6) /* Bit 6: Receive Packet Pending Interrupt */ + /* Bit 7: Reserved */ + +/* Ethernet Status Register Bit Definitions */ + +#define ESTAT_CLKRDY (1 << 0) /* Bit 0: Clock Ready */ +#define ESTAT_TXABRT (1 << 1) /* Bit 1: Transmit Abort Error */ +#define ESTAT_RXBUSY (1 << 2) /* Bit 2: Receive Busy */ + /* Bit 3: Reserved */ +#define ESTAT_LATECOL (1 << 4) /* Bit 4: Late Collision Error */ + /* Bit 5: Reserved */ +#define ESTAT_BUFER (1 << 6) /* Bit 6: Ethernet Buffer Error Status */ +#define ESTAT_INT (1 << 7) /* Bit 7: INT Interrupt */ + +/* Ethernet Control 1 Register Bit Definitions */ + +#define ECON1_BSEL_SHIFT (0) /* Bits 0-1: Bank select */ +#define ECON1_BSEL_MASK (3 << ECON1_BSEL_SHIFT) +# define ECON1_BSEL_BANK0 (0 << 0) /* Bank 0 */ +# define ECON1_BSEL_BANK1 (1 << 1) /* Bank 1 */ +# define ECON1_BSEL_BANK2 (2 << 0) /* Bank 2 */ +# define ECON1_BSEL_BANK3 (3 << 0) /* Bank 3 */ +#define ECON1_RXEN (1 << 2) /* Bit 2: Receive Enable */ +#define ECON1_TXRTS (1 << 3) /* Bit 3: Transmit Request to Send */ +#define ECON1_CSUMEN (1 << 4) /* Bit 4: DMA Checksum Enable */ +#define ECON1_DMAST (1 << 5) /* Bit 5: DMA Start and Busy Status */ +#define ECON1_RXRST (1 << 6) /* Bit 6: Receive Logic Reset */ +#define ECON1_TXRST (1 << 7) /* Bit 7: Transmit Logic Reset */ + +/* Ethernet Control 2 Register */ + /* Bits 0-2: Reserved */ +#define ECON2_VRPS (1 << 3) /* Bit 3: Voltage Regulator Power Save Enable */ + /* Bit 4: Reserved */ +#define ECON2_PWRSV (1 << 5) /* Bit 5: Power Save Enable */ +#define ECON2_PKTDEC (1 << 6) /* Bit 6: Packet Decrement */ +#define ECON2_AUTOINC (1 << 7) /* Bit 7: Automatic Buffer Pointer Increment Enable */ + +/* Banked Control Registers *************************************************/ +/* The remaining control registers are identified with a a 5 bit address and + * a bank selection. We pack the bank number and the control register + * address together to keep the design simpler. */ #define ENC28J60_ADDR_SHIFT (0) /* Bits 0-4: Register address */ @@ -206,61 +269,71 @@ /* 0x1a: Reserved */ /* 0x1b-0x1f: EIE, EIR, ESTAT, ECON2, ECON1 */ -/* Ethernet Interrupt Enable Register Bit Definitions */ +/* PHY Registers ************************************************************/ -#define EIE_RXERIE (1 << 0) /* Bit 0: Receive Error Interrupt Enable */ -#define EIE_TXERIE (1 << 1) /* Bit 1: Transmit Error Interrupt Enable */ - /* Bit 2: Reserved */ -#define EIE_TXIE (1 << 3) /* Bit 3: Transmit Enable */ -#define EIE_LINKIE (1 << 4) /* Bit 4: Link Status Change Interrupt Enable */ -#define EIE_DMAIE (1 << 5) /* Bit 5: DMA Interrupt Enable */ -#define EIE_PKTIE (1 << 6) /* Bit 6: Receive Packet Pending Interrupt Enable */ -#define EIE_INTIE (1 << 7) /* Bit 7: Global INT Interrupt Enable */ +#define PHCON1 (0x00) +#define PHSTAT1 (0x01) +#define PHHID1 (0x02) +#define PHHID2 (0x03) +#define PHCON2 (0x10) +#define PHSTAT2 (0x11) +#define PHIE (0x12) +#define PHIR (0x13) +#define PHLCON (0x14) -/* Ethernet Interupt Request Register Bit Definitions */ +/* PHCON1 Register Bit Definitions */ -#define EIR_RXERIF (1 << 0) /* Bit 0: Receive Error Interrupt */ -#define EIR_TXERIF (1 << 1) /* Bit 1: Transmit Error Interrupt */ - /* Bit 2: Reserved */ -#define EIR_TXIF (1 << 3) /* Bit 3: Transmit Interrupt */ -#define EIR_LINKIF (1 << 4) /* Bit 4: Link Change Interrupt */ -#define EIR_DMAIF (1 << 5) /* Bit 5: DMA Interrupt */ -#define EIR_PKTIF (1 << 6) /* Bit 6: Receive Packet Pending Interrupt */ - /* Bit 7: Reserved */ +#define PHCON1_PDPXMD (1 << 8) /* Bit 8: PHY Power-Down */ +#define PHCON1_PPWRSV (1 << 11) /* Bit 11: PHY Power-Down */ +#define PHCON1_PLOOPBK (1 << 14) /* Bit 14: PHY Loopback */ +#define PHCON1_PRST (1 << 15) /* Bit 15: PHY Software Reset */ -/* Ethernet Status Register Bit Definitions */ +/* PHSTAT1 Register Bit Definitions */ -#define ESTAT_CLKRDY (1 << 0) /* Bit 0: Clock Ready */ -#define ESTAT_TXABRT (1 << 1) /* Bit 1: Transmit Abort Error */ -#define ESTAT_RXBUSY (1 << 2) /* Bit 2: Receive Busy */ - /* Bit 3: Reserved */ -#define ESTAT_LATECOL (1 << 4) /* Bit 4: Late Collision Error */ - /* Bit 5: Reserved */ -#define ESTAT_BUFER (1 << 6) /* Bit 6: Ethernet Buffer Error Status */ -#define ESTAT_INT (1 << 7) /* Bit 7: INT Interrupt */ +#define PHSTAT1_JBSTAT (1 << 1) /* Bit 1: PHY Latching Jabber Status */ +#define PHSTAT1_LLSTAT (1 << 2) /* Bit 2: PHY Latching Link Status */ +#define PHSTAT1_PHDPX (1 << 11) /* Bit 11: PHY Half-Duplex Capable */ +#define PHSTAT1_PFDPX (1 << 12) /* Bit 12: PHY Full-Duplex Capable */ -/* Ethernet Control 1 Register Bit Definitions */ +/* PHCON2 Register Bit Definitions */ -#define ECON1_BSEL_SHIFT (0) /* Bits 0-1: Bank select */ -#define ECON1_BSEL_MASK (3 << ECON1_BSEL_SHIFT) -# define ECON1_BSEL_BANK0 (0 << 0) /* Bank 0 */ -# define ECON1_BSEL_BANK1 (1 << 1) /* Bank 1 */ -# define ECON1_BSEL_BANK2 (2 << 0) /* Bank 2 */ -# define ECON1_BSEL_BANK3 (3 << 0) /* Bank 3 */ -#define ECON1_RXEN (1 << 2) /* Bit 2: Receive Enable */ -#define ECON1_TXRTS (1 << 3) /* Bit 3: Transmit Request to Send */ -#define ECON1_CSUMEN (1 << 4) /* Bit 4: DMA Checksum Enable */ -#define ECON1_DMAST (1 << 5) /* Bit 5: DMA Start and Busy Status */ -#define ECON1_RXRST (1 << 6) /* Bit 6: Receive Logic Reset */ -#define ECON1_TXRST (1 << 7) /* Bit 7: Transmit Logic Reset */ +#define PHCON2_HDLDIS (1 << 8) /* Bit 8: PHY Half-Duplex Loopback Disable */ +#define PHCON2_JABBER (1 << 10) /* Bit 10: Jabber Correction Disable */ +#define PHCON2_TXDIS (1 << 13) /* Bit 13: Twisted-Pair Transmitter Disable */ +#define PHCON2_FRCLINK (1 << 14) /* Bit 14: PHY Force Linkup */ -/* Ethernet Control 2 Register */ - /* Bits 0-2: Reserved */ -#define ECON2_VRPS (1 << 3) /* Bit 3: Voltage Regulator Power Save Enable */ - /* Bit 4: Reserved */ -#define ECON2_PWRSV (1 << 5) /* Bit 5: Power Save Enable */ -#define ECON2_PKTDEC (1 << 6) /* Bit 6: Packet Decrement */ -#define ECON2_AUTOINC (1 << 7) /* Bit 7: Automatic Buffer Pointer Increment Enable */ +/* PHSTAT2 Register Bit Definitions */ + +#define PHSTAT2_PLRITY (1 << 5) /* Bit 5: Polarity Status */ +#define PHSTAT2_DPXSTAT (1 << 9) /* Bit 9: PHY Duplex Status */ +#define PHSTAT2_LSTAT (1 << 10) /* Bit 10: PHY Link Status */ +#define PHSTAT2_COLSTAT (1 << 11) /* Bit 11: PHY Collision Status */ +#define PHSTAT2_RXSTAT (1 << 12) /* Bit 12: PHY Receive Status */ +#define PHSTAT2_TXSTAT (1 << 13) /* Bit 13: PHY Transmit Status */ + +/* PHIE Regiser Bit Definitions */ + +#define PHIE_PGEIE (1 << 1) +#define PHIE_PLNKIE (1 << 4) + +/* PHIR Regiser Bit Definitions */ + +#define PHIR_PGIF (1 << 2) +#define PHIR_PLNKIF (1 << 4) + +/* PHLCON Regiser Bit Definitions */ + +#define PHLCON_STRCH (1 << 1) /* Bit 1: LED Pulse Stretching Enable */ +#define PHLCON_LFRQ0 (1 << 2) /* Bit 2: LED Pulse Stretch Time Configuration */ +#define PHLCON_LFRQ1 (1 << 3) /* Bit 3: " " " " " " " " " */ +#define PHLCON_LBCFG0 (1 << 4) /* Bit 4: LEDB Configuration */ +#define PHLCON_LBCFG1 (1 << 5) /* Bit 5: " " " " */ +#define PHLCON_LBCFG2 (1 << 6) /* Bit 6: " " " " */ +#define PHLCON_LBCFG3 (1 << 7) /* Bit 7: " " " " */ +#define PHLCON_LACFG0 (1 << 8) /* Bit 8: LEDA Configuration */ +#define PHLCON_LACFG1 (1 << 9) /* Bit 9: " " " " */ +#define PHLCON_LACFG2 (1 << 10) /* Bit 10: " " " " */ +#define PHLCON_LACFG3 (1 << 11) /* Bit 11: " " " " */ /**************************************************************************** * Public Types -- cgit v1.2.3