From 65e82f8b46538cf3b00a20f44864e862b76d7eb7 Mon Sep 17 00:00:00 2001 From: patacongo Date: Fri, 15 Apr 2011 19:30:06 +0000 Subject: Add LPCXpression USB storage example git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3509 42af7a65-404d-4744-a932-0658087f49c3 --- nuttx/configs/lpcxpresso-lpc1768/README.txt | 11 + nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig | 1 - .../lpcxpresso-lpc1768/src/lpcxpresso_internal.h | 34 +- nuttx/configs/lpcxpresso-lpc1768/src/up_leds.c | 6 +- nuttx/configs/lpcxpresso-lpc1768/src/up_ssp.c | 8 +- .../lpcxpresso-lpc1768/usbstorage/Make.defs | 174 ++++ .../lpcxpresso-lpc1768/usbstorage/appconfig | 39 + .../lpcxpresso-lpc1768/usbstorage/defconfig | 892 +++++++++++++++++++++ .../lpcxpresso-lpc1768/usbstorage/ld.script | 110 +++ .../lpcxpresso-lpc1768/usbstorage/setenv.sh | 59 ++ .../configs/olimex-lpc1766stk/usbstorage/defconfig | 2 +- 11 files changed, 1318 insertions(+), 18 deletions(-) create mode 100755 nuttx/configs/lpcxpresso-lpc1768/usbstorage/Make.defs create mode 100644 nuttx/configs/lpcxpresso-lpc1768/usbstorage/appconfig create mode 100755 nuttx/configs/lpcxpresso-lpc1768/usbstorage/defconfig create mode 100755 nuttx/configs/lpcxpresso-lpc1768/usbstorage/ld.script create mode 100755 nuttx/configs/lpcxpresso-lpc1768/usbstorage/setenv.sh (limited to 'nuttx') diff --git a/nuttx/configs/lpcxpresso-lpc1768/README.txt b/nuttx/configs/lpcxpresso-lpc1768/README.txt index a37fd379b..1d21cea05 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/README.txt +++ b/nuttx/configs/lpcxpresso-lpc1768/README.txt @@ -125,6 +125,17 @@ SD Slot *J55 must be set to provide chip select PIO1_11 signal as the SD slot chip select. + + Base-board J4/J6 LPC1768 + Signal Pin Pin + ------------------- ----- -------- + PIO0_6-USB_CONNECT* 23 P0.21 + USB_DM 36 USB_D- + USB_DP 37 USB_D+ + PIO0_3-VBUS_SENSE 39 P0.5 + + *J14 must be set to permit GPIO control of the USB connect pin + J23 is associated the LEDs used for USB support Development Environment ^^^^^^^^^^^^^^^^^^^^^^^ diff --git a/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig b/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig index 08fbda866..0e32576eb 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig +++ b/nuttx/configs/lpcxpresso-lpc1768/ostest/defconfig @@ -688,7 +688,6 @@ CONFIG_EXAMPLE_UIP_DHCPC=n # # Settings for examples/nettest # -# # CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act # as either the client side or server side of the test # CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the diff --git a/nuttx/configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h b/nuttx/configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h index 71da85976..dce63cdff 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h +++ b/nuttx/configs/lpcxpresso-lpc1768/src/lpcxpresso_internal.h @@ -81,9 +81,9 @@ * P0[30]/USB_D- J6-36 USB_D- */ -#define GPIO_I2C1_EPROM_SDA GPIO_I2C1_SDA_1 -#define GPIO_I2C1_EPROM_SDL GPIO_I2C1_SCL_2 -#define GPIO_LED (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT0 | GPIO_PIN22) +#define LPCXPRESSO_I2C1_EPROM_SDA GPIO_I2C1_SDA_1 +#define LPCXPRESSO_I2C1_EPROM_SDL GPIO_I2C1_SCL_2 +#define LPCXPRESSO_LED (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT0 | GPIO_PIN22) /* P1[0]/ENET-TXD0 J6-34? TXD0 TX-(Ethernet PHY) * P1[1]/ENET_TXD1 J6-35? TXD1 TX+(Ethernet PHY) @@ -126,7 +126,7 @@ * P2[13]/EINT3/I2STX_SDA J6-27 */ -#define GPIO_USB_PULLUP (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT2 | GPIO_PIN9) +#define LPCXPRESSO_USB_PULLUP (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT2 | GPIO_PIN9) /* P3[25]/MAT0.0/PWM1.2 PAD13 N/A * P3[26]/STCLK/MAT0.1/PWM1.3 PAD14 N/A @@ -140,18 +140,34 @@ * Base-board J4/J6 LPC1768 * SD Signal Pin Pin * --- ----------- ----- -------- - * CS PIO1_11* 55 P2.2 (See GPIO_SD_CS) + * CS PIO1_11* 55 P2.2 (See LPCXPRESSO_SD_CS) * DIN PIO0_9-MOSI 5 P0.9 MOSI1 (See GPIO_SSP1_MOSI in lpc17_internal.h) * DOUT PIO0_8-MISO 6 P0.8 MISO1 (See GPIO_SSP1_MISO in lpc17_internal.h) * CLK PIO2_11-SCK 7 P0.9 SCK1 (See GPIO_SSP1_SCK in board.h) - * CD PIO2_10 52 P2.11 (See GPIO_SD_CD) + * CD PIO2_10 52 P2.11 (See LPCXPRESSO_SD_CD) */ -#define GPIO_SD_CS (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT2 | GPIO_PIN2) +#define LPCXPRESSO_SD_CS (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT2 | GPIO_PIN2) #ifdef CONFIG_GPIO_IRQ -# define GPIO_SD_CD (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN11) +# define LPCXPRESSO_SD_CD (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN11) #else -# define GPIO_SD_CD (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN11) +# define LPCXPRESSO_SD_CD (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN11) +#endif + +/* Base-board J4/J6 LPC1768 + * Signal Pin Pin + * ------------------- ----- -------- + * PIO0_6-USB_CONNECT* 23 P0.21 + * USB_DM 36 USB_D- + * USB_DP 37 USB_D+ + * PIO0_3-VBUS_SENSE 39 P0.5 + */ + +#define LPCXPRESSO_USB_CONNECT (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT0 | GPIO_PIN21) +#ifdef CONFIG_GPIO_IRQ +# define LPCXPRESSO_USB_VBUSSENSE (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN5) +#else +# define LPCXPRESSO_USB_VBUSSENSE (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN5) #endif /************************************************************************************ diff --git a/nuttx/configs/lpcxpresso-lpc1768/src/up_leds.c b/nuttx/configs/lpcxpresso-lpc1768/src/up_leds.c index 81175bde8..39c12e791 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/src/up_leds.c +++ b/nuttx/configs/lpcxpresso-lpc1768/src/up_leds.c @@ -97,7 +97,7 @@ void up_ledinit(void) { /* Configure all LED GPIO lines */ - lpc17_configgpio(GPIO_LED); + lpc17_configgpio(LPCXPRESSO_LED); g_ncstate = true; } @@ -125,7 +125,7 @@ void up_ledon(int led) return; } - lpc17_gpiowrite(GPIO_LED, off); + lpc17_gpiowrite(LPCXPRESSO_LED, off); } /**************************************************************************** @@ -151,7 +151,7 @@ void up_ledoff(int led) return; } - lpc17_gpiowrite(GPIO_LED, off); + lpc17_gpiowrite(LPCXPRESSO_LED, off); } #endif /* CONFIG_ARCH_LEDS */ diff --git a/nuttx/configs/lpcxpresso-lpc1768/src/up_ssp.c b/nuttx/configs/lpcxpresso-lpc1768/src/up_ssp.c index d3977b852..b15d97358 100755 --- a/nuttx/configs/lpcxpresso-lpc1768/src/up_ssp.c +++ b/nuttx/configs/lpcxpresso-lpc1768/src/up_ssp.c @@ -113,8 +113,8 @@ void weak_function lpc17_sspinitialize(void) */ #ifdef CONFIG_LPC17_SSP1 - (void)lpc17_configgpio(GPIO_SD_CS); - (void)lpc17_configgpio(GPIO_SD_CD); + (void)lpc17_configgpio(LPCXPRESSO_SD_CS); + (void)lpc17_configgpio(LPCXPRESSO_SD_CD); #endif ssp_dumpgpio("lpc17_sspinitialize() Exit"); @@ -173,7 +173,7 @@ void lpc17_ssp1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool sel { /* Assert/de-assert the CS pin to the card */ - (void)lpc17_gpiowrite(GPIO_SD_CS, !selected); + (void)lpc17_gpiowrite(LPCXPRESSO_SD_CS, !selected); } ssp_dumpgpio("lpc17_spi1select() Exit"); @@ -185,7 +185,7 @@ uint8_t lpc17_ssp1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid) { /* Read the state of the card-detect bit */ - if (lpc17_gpioread(GPIO_SD_CD) == 0) + if (lpc17_gpioread(LPCXPRESSO_SD_CD) == 0) { sspdbg("Returning SPI_STATUS_PRESENT\n"); return SPI_STATUS_PRESENT; diff --git a/nuttx/configs/lpcxpresso-lpc1768/usbstorage/Make.defs b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/Make.defs new file mode 100755 index 000000000..268a69e72 --- /dev/null +++ b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/Make.defs @@ -0,0 +1,174 @@ +############################################################################ +# configs/lpcxpresso-lpc1768/usbstorage/Make.defs +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +include ${TOPDIR}/.config + +# Setup for the selected toolchain + +ifeq ($(CONFIG_LPC17_CODESOURCERYW),y) + # CodeSourcery under Windows + CROSSDEV = arm-none-eabi- + WINTOOL = y + ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft +endif +ifeq ($(CONFIG_LPC17_CODESOURCERYL),y) + # CodeSourcery under Linux + CROSSDEV = arm-none-eabi- + ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft + MAXOPTIMIZATION = -O2 +endif +ifeq ($(CONFIG_LPC17_DEVKITARM),y) + # devkitARM under Windows + CROSSDEV = arm-eabi- + WINTOOL = y + ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft +endif +ifeq ($(CONFIG_LPC17_BUILDROOT),y) + # NuttX buildroot under Linux or Cygwin + CROSSDEV = arm-elf- + ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft + MAXOPTIMIZATION = -Os +endif +ifeq ($(CONFIG_LPC17_CODEREDW),y) + # CodeSourcery under Windows + CROSSDEV = arm-none-eabi- + WINTOOL = y + ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft -D__NEWLIB__ +endif +ifeq ($(CONFIG_LPC17_CODEREDL),y) + # CodeSourcery under Linux + CROSSDEV = arm-none-eabi- + ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft -D__NEWLIB__ + MAXOPTIMIZATION = -O2 +endif + +ifeq ($(WINTOOL),y) + # Windows-native toolchains + DIRLINK = $(TOPDIR)/tools/winlink.sh + DIRUNLINK = $(TOPDIR)/tools/unlink.sh + MKDEP = $(TOPDIR)/tools/mknulldeps.sh + ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" + ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}" + ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/ld.script}" + MAXOPTIMIZATION = -O2 +else + # Linux/Cygwin-native toolchain + MKDEP = $(TOPDIR)/tools/mkdeps.sh + ARCHINCLUDES = -I. -isystem $(TOPDIR)/include + ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx + ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/usbstorage/ld.script +endif + +CC = $(CROSSDEV)gcc +CXX = $(CROSSDEV)g++ +CPP = $(CROSSDEV)gcc -E +LD = $(CROSSDEV)ld +AR = $(CROSSDEV)ar rcs +NM = $(CROSSDEV)nm +OBJCOPY = $(CROSSDEV)objcopy +OBJDUMP = $(CROSSDEV)objdump + +ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'} +ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1} + +ifeq ("${CONFIG_DEBUG_SYMBOLS}","y") + ARCHOPTIMIZATION = -g +else + ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer +endif + +ARCHCFLAGS = -fno-builtin +ARCHCXXFLAGS = -fno-builtin -fno-exceptions +ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow +ARCHWARNINGSXX = -Wall -Wshadow +ARCHDEFINES = +ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10 + +CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe +CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS) +CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe +CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS) +CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) +AFLAGS = $(CFLAGS) -D__ASSEMBLY__ + +NXFLATLDFLAGS1 = -r -d -warn-common +NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections +LDNXFLATFLAGS = -e main -s 2048 + +OBJEXT = .o +LIBEXT = .a +EXEEXT = + +ifneq ($(CROSSDEV),arm-elf-) + LDFLAGS += -nostartfiles -nodefaultlibs +endif +ifeq ($(CONFIG_DEBUG_SYMBOLS),y) + LDFLAGS += -g +endif + +define PREPROCESS + @echo "CPP: $1->$2" + @$(CPP) $(CPPFLAGS) $1 -o $2 +endef + +define COMPILE + @echo "CC: $1" + @$(CC) -c $(CFLAGS) $1 -o $2 +endef + +define COMPILEXX + @echo "CXX: $1" + @$(CXX) -c $(CXXFLAGS) $1 -o $2 +endef + +define ASSEMBLE + @echo "AS: $1" + @$(CC) -c $(AFLAGS) $1 -o $2 +endef + +define ARCHIVE + echo "AR: $2"; \ + $(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; } +endef + +define CLEAN + @rm -f *.o *.a +endef + +HOSTCC = gcc +HOSTINCLUDES = -I. +HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe +HOSTLDFLAGS = + diff --git a/nuttx/configs/lpcxpresso-lpc1768/usbstorage/appconfig b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/appconfig new file mode 100644 index 000000000..1f158cd5e --- /dev/null +++ b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/appconfig @@ -0,0 +1,39 @@ +############################################################################ +# configs/lpcxpresso-lpc1768/usbstorage/appconfig +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +# Path to example in apps/examples containing the user_start entry point + +CONFIGURED_APPS += examples/usbstorage + diff --git a/nuttx/configs/lpcxpresso-lpc1768/usbstorage/defconfig b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/defconfig new file mode 100755 index 000000000..abb4f6761 --- /dev/null +++ b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/defconfig @@ -0,0 +1,892 @@ +############################################################################ +# configs/lpcxpresso-lpc1768/usbstorage/defconfig +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +# +# architecture selection +# +# CONFIG_ARCH - identifies the arch subdirectory and, hence, the +# processor architecture. +# CONFIG_ARCH_family - for use in C code. This identifies the +# particular chip family that the architecture is implemented +# in. +# CONFIG_ARCH_architecture - for use in C code. This identifies the +# specific architecture within the chip familyl. +# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory +# CONFIG_ARCH_CHIP_name - For use in C code +# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, +# the board that supports the particular chip or SoC. +# CONFIG_ARCH_BOARD_name - for use in C code +# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) +# CONFIG_BOARD_LOOPSPERMSEC - for delay loops +# CONFIG_DRAM_SIZE - Describes the installed DRAM. +# CONFIG_DRAM_START - The start address of DRAM (physical) +# CONFIG_DRAM_END - Last address+1 of installed RAM +# CONFIG_ARCH_IRQPRIO - The LPC17xx supports interrupt prioritization +# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt +# stack. If defined, this symbol is the size of the interrupt +# stack in bytes. If not defined, the user task stacks will be +# used during interrupt handling. +# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions +# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. +# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. +# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. +# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that +# cause a 100 second delay during boot-up. This 100 second delay +# serves no purpose other than it allows you to calibrate +# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure +# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until +# the delay actually is 100 seconds. +# CONFIG_ARCH_DMA - Support DMA initialization +# +CONFIG_ARCH=arm +CONFIG_ARCH_ARM=y +CONFIG_ARCH_CORTEXM3=y +CONFIG_ARCH_CHIP=lpc17xx +CONFIG_ARCH_CHIP_LPC1768=y +CONFIG_ARCH_BOARD=lpcxpresso-lpc1768 +CONFIG_ARCH_BOARD_LPCXPRESSO=y +CONFIG_BOARD_LOOPSPERMSEC=7982 +CONFIG_DRAM_SIZE=(32*1024) +CONFIG_DRAM_START=0x10000000 +CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE) +CONFIG_ARCH_IRQPRIO=y +CONFIG_ARCH_INTERRUPTSTACK=n +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARCH_BOOTLOADER=n +CONFIG_ARCH_LEDS=y +CONFIG_ARCH_BUTTONS=n +CONFIG_ARCH_CALIBRATION=n +CONFIG_ARCH_DMA=n + +# +# Identify toolchain and linker options +# +CONFIG_LPC17_CODESOURCERYW=n +CONFIG_LPC17_CODESOURCERYL=n +CONFIG_LPC17_DEVKITARM=n +CONFIG_LPC17_BUILDROOT=n +CONFIG_LPC17_CODEREDW=n +CONFIG_LPC17_CODEREDL=y + +# +# Individual subsystems can be enabled: +# +# Individual subsystems can be enabled: +# (MAINOSC, PLL0, PLL1 and FLASH are controlled in board.h) +# +CONFIG_LPC17_ETHERNET=n +CONFIG_LPC17_USBHOST=n +CONFIG_LPC17_USBOTG=n +CONFIG_LPC17_USBDEV=y +CONFIG_LPC17_UART0=n +CONFIG_LPC17_UART1=n +CONFIG_LPC17_UART2=n +CONFIG_LPC17_UART3=y +CONFIG_LPC17_CAN1=n +CONFIG_LPC17_CAN2=n +CONFIG_LPC17_SPI=n +CONFIG_LPC17_SSP0=n +CONFIG_LPC17_SSP1=y +CONFIG_LPC17_I2C0=n +CONFIG_LPC17_I2C1=n +CONFIG_LPC17_I2S=n +CONFIG_LPC17_TMR0=n +CONFIG_LPC17_TMR1=n +CONFIG_LPC17_TMR2=n +CONFIG_LPC17_TMR3=n +CONFIG_LPC17_RIT=n +CONFIG_LPC17_PWM=n +CONFIG_LPC17_MCPWM=n +CONFIG_LPC17_QEI=n +CONFIG_LPC17_RTC=n +CONFIG_LPC17_WDT=n +CONFIG_LPC17_ADC=n +CONFIG_LPC17_DAC=n +CONFIG_LPC17_GPDMA=n + +# +# LPC17xx specific serial device driver settings +# +# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the +# console and ttys0 (default is the UART1). +# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received. +# This specific the size of the receive buffer +# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before +# being sent. This specific the size of the transmit buffer +# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be +# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8. +# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity +# CONFIG_UARTn_2STOP - Two stop bits +# +CONFIG_UART0_SERIAL_CONSOLE=n +CONFIG_UART1_SERIAL_CONSOLE=n +CONFIG_UART2_SERIAL_CONSOLE=n +CONFIG_UART3_SERIAL_CONSOLE=y + +CONFIG_UART0_TXBUFSIZE=256 +CONFIG_UART1_TXBUFSIZE=256 +CONFIG_UART2_TXBUFSIZE=256 +CONFIG_UART3_TXBUFSIZE=256 + +CONFIG_UART0_RXBUFSIZE=256 +CONFIG_UART1_RXBUFSIZE=256 +CONFIG_UART2_RXBUFSIZE=256 +CONFIG_UART3_RXBUFSIZE=256 + +CONFIG_UART0_BAUD=115200 +CONFIG_UART2_BAUD=115200 +CONFIG_UART3_BAUD=115200 +CONFIG_UART1_BAUD=115200 + +CONFIG_UART0_BITS=8 +CONFIG_UART1_BITS=8 +CONFIG_UART2_BITS=8 +CONFIG_UART3_BITS=8 + +CONFIG_UART0_PARITY=0 +CONFIG_UART1_PARITY=0 +CONFIG_UART2_PARITY=0 +CONFIG_UART3_PARITY=0 + +CONFIG_UART0_2STOP=0 +CONFIG_UART1_2STOP=0 +CONFIG_UART2_2STOP=0 +CONFIG_UART3_2STOP=0 + +# +# LPC17xx specific PHY/Ethernet device driver settings +# +# CONFIG_PHY_KS8721 - Selects Micrel KS8721 PHY +# CONFIG_PHY_AUTONEG - Enable auto-negotion +# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed. +# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex +# CONFIG_NET_EMACRAM_SIZE - Size of EMAC RAM. Default: 16Kb +# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 18 +# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 18 +# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is +# the higest priority. +# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented). +# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs +# CONFIG_DEBUG. +# CONFIG_NET_HASH - Enable receipt of near-perfect match frames. +# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames. +# Automatically set if CONFIG_NET_IGMP is selected. +# +CONFIG_PHY_KS8721=y +CONFIG_PHY_AUTONEG=y +CONFIG_PHY_SPEED100=n +CONFIG_PHY_FDUPLEX=y + +# +# General build options +# +# CONFIG_RRLOAD_BINARY - make the rrload binary format used with +# BSPs from www.ridgerun.com using the tools/mkimage.sh script +# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_RAW_BINARY - make a raw binary format file used with many +# different loaders using the GNU objcopy program. This option +# should not be selected if you are not using the GNU toolchain. +# CONFIG_HAVE_LIBM - toolchain supports libm.a +# +CONFIG_RRLOAD_BINARY=n +CONFIG_INTELHEX_BINARY=y +CONFIG_MOTOROLA_SREC=n +CONFIG_RAW_BINARY=n +CONFIG_HAVE_LIBM=n + +# +# General OS setup +# +# CONFIG_APPS_DIR - Identifies the relative path to the directory +# that builds the application to link with NuttX. Default: ../apps +# CONFIG_DEBUG - enables built-in debug options +# CONFIG_DEBUG_VERBOSE - enables verbose debug output +# CONFIG_DEBUG_SYMBOLS - build without optimization and with +# debug symbols (needed for use with a debugger). +# CONFIG_MM_REGIONS - If the architecture includes multiple +# regions of memory to allocate from, this specifies the +# number of memory regions that the memory manager must +# handle and enables the API mm_addregion(start, end); +# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot +# time console output +# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz +# or TICKS_PER_MSEC=10. This setting may be defined to +# inform NuttX that the processor hardware is providing +# system timer interrupts at some interrupt interval other +# than 10 msec. +# CONFIG_RR_INTERVAL - The round robin timeslice will be set +# this number of milliseconds; Round robin scheduling can +# be disabled by setting this value to zero. +# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in +# scheduler to monitor system performance +# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a +# task name to save in the TCB. Useful if scheduler +# instrumentation is selected. Set to zero to disable. +# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - +# Used to initialize the internal time logic. +# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. +# You would only need this if you are concerned about accurate +# time conversions in the past or in the distant future. +# CONFIG_JULIAN_TIME - Enables Julian time conversions. You +# would only need this if you are concerned about accurate +# time conversion in the distand past. You must also define +# CONFIG_GREGORIAN_TIME in order to use Julian time. +# CONFIG_DEV_CONSOLE - Set if architecture-specific logic +# provides /dev/console. Enables stdout, stderr, stdin. +# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console +# driver (minimul support) +# CONFIG_MUTEX_TYPES: Set to enable support for recursive and +# errorcheck mutexes. Enables pthread_mutexattr_settype(). +# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority +# inheritance on mutexes and semaphores. +# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority +# inheritance is enabled. It defines the maximum number of +# different threads (minus one) that can take counts on a +# semaphore with priority inheritance support. This may be +# set to zero if priority inheritance is disabled OR if you +# are only using semaphores as mutexes (only one holder) OR +# if no more than two threads participate using a counting +# semaphore. +# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, +# then this setting is the maximum number of higher priority +# threads (minus 1) than can be waiting for another thread +# to release a count on a semaphore. This value may be set +# to zero if no more than one thread is expected to wait for +# a semaphore. +# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors +# by task_create() when a new task is started. If set, all +# files/drivers will appear to be closed in the new task. +# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first +# three file descriptors (stdin, stdout, stderr) by task_create() +# when a new task is started. If set, all files/drivers will +# appear to be closed in the new task except for stdin, stdout, +# and stderr. +# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket +# desciptors by task_create() when a new task is started. If +# set, all sockets will appear to be closed in the new task. +# CONFIG_NXFLAT. Enable support for the NXFLAT binary format. +# This format will support execution of NuttX binaries located +# in a ROMFS filesystem (see examples/nxflat). +# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to +# handle delayed processing from interrupt handlers. This feature +# is required for some drivers but, if there are not complaints, +# can be safely disabled. The worker thread also performs +# garbage collection -- completing any delayed memory deallocations +# from interrupt handlers. If the worker thread is disabled, +# then that clean will be performed by the IDLE thread instead +# (which runs at the lowest of priority and may not be appropriate +# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE +# is enabled, then the following options can also be used: +# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker +# thread. Default: 50 +# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for +# work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker +# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up +# the worker thread. Default: 4 +# +#CONFIG_APPS_DIR= +CONFIG_DEBUG=n +CONFIG_DEBUG_VERBOSE=n +CONFIG_DEBUG_SYMBOLS=n +CONFIG_DEBUG_USB=n +CONFIG_MM_REGIONS=2 +CONFIG_ARCH_LOWPUTC=y +CONFIG_RR_INTERVAL=200 +CONFIG_SCHED_INSTRUMENTATION=n +CONFIG_TASK_NAME_SIZE=0 +CONFIG_START_YEAR=2011 +CONFIG_START_MONTH=4 +CONFIG_START_DAY=15 +CONFIG_GREGORIAN_TIME=n +CONFIG_JULIAN_TIME=n +CONFIG_DEV_CONSOLE=y +CONFIG_DEV_LOWCONSOLE=n +CONFIG_MUTEX_TYPES=n +CONFIG_PRIORITY_INHERITANCE=n +CONFIG_SEM_PREALLOCHOLDERS=0 +CONFIG_SEM_NNESTPRIO=0 +CONFIG_FDCLONE_DISABLE=n +CONFIG_FDCLONE_STDIO=n +CONFIG_SDCLONE_DISABLE=y +CONFIG_NXFLAT=n +CONFIG_SCHED_WORKQUEUE=n +CONFIG_SCHED_WORKPRIORITY=50 +CONFIG_SCHED_WORKPERIOD=(50*1000) +CONFIG_SCHED_WORKSTACKSIZE=1024 +CONFIG_SIG_SIGWORK=4 + +# +# The following can be used to disable categories of +# APIs supported by the OS. If the compiler supports +# weak functions, then it should not be necessary to +# disable functions unless you want to restrict usage +# of those APIs. +# +# There are certain dependency relationships in these +# features. +# +# o mq_notify logic depends on signals to awaken tasks +# waiting for queues to become full or empty. +# o pthread_condtimedwait() depends on signals to wake +# up waiting tasks. +# +CONFIG_DISABLE_CLOCK=n +CONFIG_DISABLE_POSIX_TIMERS=n +CONFIG_DISABLE_PTHREAD=n +CONFIG_DISABLE_SIGNALS=n +CONFIG_DISABLE_MQUEUE=n +CONFIG_DISABLE_MOUNTPOINT=y +CONFIG_DISABLE_ENVIRON=n +CONFIG_DISABLE_POLL=y + +# +# Misc libc settings +# +# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a +# little smaller if we do not support fieldwidthes +# +CONFIG_NOPRINTF_FIELDWIDTH=n + +# +# Allow for architecture optimized implementations +# +# The architecture can provide optimized versions of the +# following to improve system performance +# +CONFIG_ARCH_MEMCPY=n +CONFIG_ARCH_MEMCMP=n +CONFIG_ARCH_MEMMOVE=n +CONFIG_ARCH_MEMSET=n +CONFIG_ARCH_STRCMP=n +CONFIG_ARCH_STRCPY=n +CONFIG_ARCH_STRNCPY=n +CONFIG_ARCH_STRLEN=n +CONFIG_ARCH_STRNLEN=n +CONFIG_ARCH_BZERO=n + +# +# Sizes of configurable things (0 disables) +# +# CONFIG_MAX_TASKS - The maximum number of simultaneously +# active tasks. This value must be a power of two. +# CONFIG_MAX_TASK_ARGS - This controls the maximum number of +# of parameters that a task may receive (i.e., maxmum value +# of 'argc') +# CONFIG_NPTHREAD_KEYS - The number of items of thread- +# specific data that can be retained +# CONFIG_NFILE_DESCRIPTORS - The maximum number of file +# descriptors (one for each open) +# CONFIG_NFILE_STREAMS - The maximum number of streams that +# can be fopen'ed +# CONFIG_NAME_MAX - The maximum size of a file name. +# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate +# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_NUNGET_CHARS - Number of characters that can be +# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message +# structures. The system manages a pool of preallocated +# message structures to minimize dynamic allocations +# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with +# a fixed payload size given by this settin (does not include +# other message structure overhead. +# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that +# can be passed to a watchdog handler +# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog +# structures. The system manages a pool of preallocated +# watchdog structures to minimize dynamic allocations +# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX +# timer structures. The system manages a pool of preallocated +# timer structures to minimize dynamic allocations. Set to +# zero for all dynamic allocations. +# +CONFIG_MAX_TASKS=16 +CONFIG_MAX_TASK_ARGS=4 +CONFIG_NPTHREAD_KEYS=4 +CONFIG_NFILE_DESCRIPTORS=8 +CONFIG_NFILE_STREAMS=8 +CONFIG_NAME_MAX=32 +CONFIG_STDIO_BUFFER_SIZE=256 +CONFIG_NUNGET_CHARS=2 +CONFIG_PREALLOC_MQ_MSGS=4 +CONFIG_MQ_MAXMSGSIZE=32 +CONFIG_MAX_WDOGPARMS=2 +CONFIG_PREALLOC_WDOGS=4 +CONFIG_PREALLOC_TIMERS=4 + +# +# Filesystem configuration +# +# CONFIG_FS_FAT - Enable FAT filesystem support +# CONFIG_FAT_SECTORSIZE - Max supported sector size +# CONFIG_FS_ROMFS - Enable ROMFS filesystem support +# +CONFIG_FS_FAT=n +CONFIG_FS_ROMFS=n + +# +# SPI-based MMC/SD driver +# +# CONFIG_MMCSD_NSLOTS +# Number of MMC/SD slots supported by the driver +# CONFIG_MMCSD_READONLY +# Provide read-only access (default is read/write) +# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. +# Default is 20MHz. +# +CONFIG_MMCSD_NSLOTS=1 +CONFIG_MMCSD_READONLY=n +CONFIG_MMCSD_SPICLOCK=12500000 + +# +# Block driver buffering +# +# CONFIG_FS_READAHEAD +# Enable read-ahead buffering +# CONFIG_FS_WRITEBUFFER +# Enable write buffering +# +CONFIG_FS_READAHEAD=n +CONFIG_FS_WRITEBUFFER=n + +# +# SDIO-based MMC/SD driver +# +# CONFIG_SDIO_DMA +# SDIO driver supports DMA +# CONFIG_MMCSD_MMCSUPPORT +# Enable support for MMC cards +# CONFIG_MMCSD_HAVECARDDETECT +# SDIO driver card detection is 100% accurate +# +CONFIG_SDIO_DMA=n +CONFIG_MMCSD_MMCSUPPORT=n +CONFIG_MMCSD_HAVECARDDETECT=n + +# +# TCP/IP and UDP support via uIP +# CONFIG_NET - Enable or disable all network features +# CONFIG_NET_IPv6 - Build in support for IPv6 +# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread. +# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options +# CONFIG_NET_BUFSIZE - uIP buffer size +# CONFIG_NET_TCP - TCP support on or off +# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks) +# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers +# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero) +# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until +# accept() is called. The size of the backlog is selected when listen() is called. +# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks) +# CONFIG_NET_UDP - UDP support on or off +# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off +# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections +# CONFIG_NET_ICMP - ICMP ping response support on or off +# CONFIG_NET_ICMP_PING - ICMP ping request support on or off +# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address +# CONFIG_NET_STATISTICS - uIP statistics on or off +# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window +# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table +# CONFIG_NET_BROADCAST - Broadcast support +# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates +# +CONFIG_NET=n +CONFIG_NET_IPv6=n +CONFIG_NSOCKET_DESCRIPTORS=0 +CONFIG_NET_SOCKOPTS=y +CONFIG_NET_BUFSIZE=420 +CONFIG_NET_TCP=n +CONFIG_NET_TCP_CONNS=40 +CONFIG_NET_MAX_LISTENPORTS=40 +CONFIG_NET_UDP=n +CONFIG_NET_UDP_CHECKSUMS=y +#CONFIG_NET_UDP_CONNS=10 +CONFIG_NET_ICMP=n +CONFIG_NET_ICMP_PING=n +#CONFIG_NET_PINGADDRCONF=0 +CONFIG_NET_STATISTICS=y +#CONFIG_NET_RECEIVE_WINDOW= +#CONFIG_NET_ARPTAB_SIZE=8 +CONFIG_NET_BROADCAST=n +#CONFIG_NET_FWCACHE_SIZE=2 + +# +# UIP Network Utilities +# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP +# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries +# +CONFIG_NET_DHCP_LIGHT=n +CONFIG_NET_RESOLV_ENTRIES=4 + +# +# USB Device Configuration +# +# CONFIG_USBDEV +# Enables USB device support +# CONFIG_USBDEV_ISOCHRONOUS +# Build in extra support for isochronous endpoints +# CONFIG_USBDEV_DUALSPEED +# Hardware handles high and full speed operation (USB 2.0) +# CONFIG_USBDEV_SELFPOWERED +# Will cause USB features to indicate that the device is +# self-powered +# CONFIG_USBDEV_MAXPOWER +# Maximum power consumption in mA +# CONFIG_USBDEV_TRACE +# Enables USB tracing for debug +# CONFIG_USBDEV_TRACE_NRECORDS +# Number of trace entries to remember +# +CONFIG_USBDEV=y +CONFIG_USBDEV_ISOCHRONOUS=n +CONFIG_USBDEV_DUALSPEED=n +CONFIG_USBDEV_SELFPOWERED=y +CONFIG_USBDEV_REMOTEWAKEUP=n +CONFIG_USBDEV_MAXPOWER=100 +CONFIG_USBDEV_TRACE=n +CONFIG_USBDEV_TRACE_NRECORDS=128 + +# +# LPC17xx USB Configuration +# +# CONFIG_LPC17_USBDEV_FRAME_INTERRUPT +# Handle USB Start-Of-Frame events. +# Enable reading SOF from interrupt handler vs. simply reading on demand. +# Probably a bad idea... Unless there is some issue with sampling the SOF +# from hardware asynchronously. +# CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT +# Enable high priority interrupts. I have no idea why you might want to +# do that +# CONFIG_LPC17_USBDEV_NDMADESCRIPTORS +# Number of DMA descriptors to allocate in SRAM. +# CONFIG_LPC17_USBDEV_DMA +# Enable lpc17xx-specific DMA support +# +CONFIG_LPC17_USBDEV_FRAME_INTERRUPT=n +CONFIG_LPC17_USBDEV_EPFAST_INTERRUPT=n +CONFIG_LPC17_USBDEV_DMA=n +CONFIG_LPC17_USBDEV_NDMADESCRIPTORS=0 +CONFIG_LPC17_USBDEV_DMAINTMASK=0 + +# +# USB Serial Device Configuration +# +# CONFIG_USBSER +# Enable compilation of the USB serial driver +# CONFIG_USBSER_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation +# CONFIG_USBSER_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation +# CONFIG_USBSER_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation +# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR +# The vendor ID code/string +# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR +# The product ID code/string +# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE +# Size of the serial receive/transmit buffers +# +CONFIG_USBSER=n +CONFIG_USBSER_EPINTIN=1 +CONFIG_USBSER_EPBULKOUT=2 +CONFIG_USBSER_EPBULKIN=5 +CONFIG_USBSER_NWRREQS=4 +CONFIG_USBSER_NRDREQS=4 +CONFIG_USBSER_VENDORID=0x067b +CONFIG_USBSER_PRODUCTID=0x2303 +CONFIG_USBSER_VENDORSTR="Nuttx" +CONFIG_USBSER_PRODUCTSTR="USBdev Serial" +CONFIG_USBSER_RXBUFSIZE=512 +CONFIG_USBSER_TXBUFSIZE=512 + +# +# USB Storage Device Configuration +# +# CONFIG_USBSTRG +# Enable compilation of the USB storage driver +# CONFIG_USBSTRG_EP0MAXPACKET +# Max packet size for endpoint 0 +# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN +# The logical 7-bit address of a hardware endpoints that support +# bulk OUT and IN operations +# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS +# The number of write/read requests that can be in flight +# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN +# The size of the buffer in each write/read request. This +# value needs to be at least as large as the endpoint +# maxpacket and ideally as large as a block device sector. +# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR +# The vendor ID code/string +# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR +# The product ID code/string +# CONFIG_USBSTRG_REMOVABLE +# Select if the media is removable +# +CONFIG_USBSTRG=y +CONFIG_USBSTRG_EP0MAXPACKET=64 +CONFIG_USBSTRG_EPBULKOUT=2 +CONFIG_USBSTRG_EPBULKIN=5 +CONFIG_USBSTRG_NRDREQS=2 +CONFIG_USBSTRG_NWRREQS=2 +CONFIG_USBSTRG_BULKINREQLEN=256 +CONFIG_USBSTRG_BULKOUTREQLEN=256 +CONFIG_USBSTRG_VENDORID=0x584e +CONFIG_USBSTRG_VENDORSTR="NuttX" +CONFIG_USBSTRG_PRODUCTID=0x5342 +CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage" +CONFIG_USBSTRG_VERSIONNO=0x0399 +CONFIG_USBSTRG_REMOVABLE=y + +# +# Settings for examples/uip +# +CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_UIP_DHCPC=n + +# +# Settings for examples/nettest +# +# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act +# as either the client side or server side of the test +# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the +# client side simply receives messages forever, allowing +# measurement of throughput +# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has +# no MAC address; one will be assigned +# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address +# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address +# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask +# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the +# client side of the test (may be target or host) +# +CONFIG_EXAMPLE_NETTEST_SERVER=n +CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n +CONFIG_EXAMPLE_NETTEST_NOMAC=y +CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) + +# +# Settings for examples/ostest +# +CONFIG_EXAMPLES_OSTEST_LOOPS=1 +CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048 +CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 + +# +# Settings for apps/nshlib +# +# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer +# CONFIG_NSH_STRERROR - Use strerror(errno) +# CONFIG_NSH_LINELEN - Maximum length of one command line +# CONFIG_NSH_STACKSIZE - Stack size to use for new threads. +# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi +# CONFIG_NSH_DISABLESCRIPT - Disable scripting support +# CONFIG_NSH_DISABLEBG - Disable background commands +# CONFIG_NSH_ROMFSETC - Use startup script in /etc +# CONFIG_NSH_CONSOLE - Use serial console front end +# CONFIG_NSH_TELNET - Use telnetd console front end +# CONFIG_NSH_ARCHINIT - Platform provides architecture +# specific initialization (nsh_archinitialize()). +# +# If CONFIG_NSH_TELNET is selected: +# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size +# CONFIG_NSH_DHCPC - Obtain address using DHCP +# CONFIG_NSH_IPADDR - Provides static IP address +# CONFIG_NSH_DRIPADDR - Provides static router IP address +# CONFIG_NSH_NETMASK - Provides static network mask +# CONFIG_NSH_NOMAC - Use a bogus MAC address +# +# If CONFIG_NSH_ROMFSETC is selected: +# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint +# CONFIG_NSH_INITSCRIPT - Relative path to init script +# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor +# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size +# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor +# CONFIG_NSH_FATSECTSIZE - FAT FS sector size +# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors +# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint +# +CONFIG_NSH_FILEIOSIZE=512 +CONFIG_NSH_STRERROR=n +CONFIG_NSH_LINELEN=64 +CONFIG_NSH_STACKSIZE=2048 +CONFIG_NSH_NESTDEPTH=3 +CONFIG_NSH_DISABLESCRIPT=n +CONFIG_NSH_DISABLEBG=n +CONFIG_NSH_ROMFSETC=n +CONFIG_NSH_CONSOLE=y +CONFIG_NSH_TELNET=n +CONFIG_NSH_ARCHINIT=n +CONFIG_NSH_IOBUFFER_SIZE=512 +CONFIG_NSH_DHCPC=n +CONFIG_NSH_NOMAC=n +CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2) +CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) +CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0) +CONFIG_NSH_ROMFSMOUNTPT="/etc" +CONFIG_NSH_INITSCRIPT="init.d/rcS" +CONFIG_NSH_ROMFSDEVNO=0 +CONFIG_NSH_ROMFSSECTSIZE=64 +CONFIG_NSH_FATDEVNO=1 +CONFIG_NSH_FATSECTSIZE=512 +CONFIG_NSH_FATNSECTORS=1024 +CONFIG_NSH_FATMOUNTPT=/tmp + +# +# Architecture-specific NSH options +# +CONFIG_NSH_MMCSDSPIPORTNO=1 +CONFIG_NSH_MMCSDSLOTNO=0 +CONFIG_NSH_MMCSDMINOR=0 + +# +# Settings for examples/usbserial +# +# CONFIG_EXAMPLES_USBSERIAL_INONLY +# Only verify IN (device-to-host) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_OUTONLY +# Only verify OUT (host-to-device) data transfers. Default: both +# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL +# Send only small, single packet messages. Default: Send large and small. +# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG +# Send only large, multi-packet messages. Default: Send large and small. +# +CONFIG_EXAMPLES_USBSERIAL_INONLY=n +CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n +CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n +CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n + +CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n +CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n +CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n + +# +# Settings for examples/usbstorage +# +# CONFIG_EXAMPLES_USBSTRG_NLUNS +# Defines the number of logical units (LUNs) exported by the USB storage +# driver. Each LUN corresponds to one exported block driver (or partition +# of a block driver). May be 1, 2, or 3. Default is 1. +# CONFIG_EXAMPLES_USBSTRG_DEVMINOR1 +# The minor device number of the block driver for the first LUN. For +# example, N in /dev/mmcsdN. Used for registering the block driver. Default +# is zero. +# CONFIG_EXAMPLES_USBSTRG_DEVPATH1 +# The full path to the registered block driver. Default is "/dev/mmcsd0" +# CONFIG_EXAMPLES_USBSTRG_DEVMINOR2 and CONFIG_EXAMPLES_USBSTRG_DEVPATH2 +# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS +# is 2 or 3. No defaults. +# CONFIG_EXAMPLES_USBSTRG_DEVMINOR3 and CONFIG_EXAMPLES_USBSTRG_DEVPATH3 +# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS +# is 3. No defaults. +# +# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then +# the example code will also manage the USB trace output. The amount of trace output +# can be controlled using: +# +# CONFIG_EXAMPLES_USBSTRG_TRACEINIT +# Show initialization events +# CONFIG_EXAMPLES_USBSTRG_TRACECLASS +# Show class driver events +# CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS +# Show data transfer events +# CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER +# Show controller events +# CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS +# Show interrupt-related events. +# +CONFIG_EXAMPLES_USBSTRG_NLUNS=1 +CONFIG_EXAMPLES_USBSTRG_DEVMINOR1=0 +CONFIG_EXAMPLES_USBSTRG_DEVPATH1="/dev/mmcsd0" +CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n +CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n +CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n + +CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n +CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n +CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n +CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n +CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n + +# +# Stack and heap information +# +# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP +# operation from FLASH but must copy initialized .data sections to RAM. +# (should also be =n for the LPC17xx which always runs from flash) +# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH +# but copy themselves entirely into RAM for better performance. +# CONFIG_CUSTOM_STACK - The up_ implementation will handle +# all stack operations outside of the nuttx model. +# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) +# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. +# This is the thread that (1) performs the inital boot of the system up +# to the point where user_start() is spawned, and (2) there after is the +# IDLE thread that executes only when there is no other thread ready to +# run. +# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate +# for the main user thread that begins at the user_start() entry point. +# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size +# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size +# CONFIG_HEAP_BASE - The beginning of the heap +# CONFIG_HEAP_SIZE - The size of the heap +# +CONFIG_BOOT_RUNFROMFLASH=n +CONFIG_BOOT_COPYTORAM=n +CONFIG_CUSTOM_STACK=n +CONFIG_STACK_POINTER= +CONFIG_IDLETHREAD_STACKSIZE=1024 +CONFIG_USERMAIN_STACKSIZE=2048 +CONFIG_PTHREAD_STACK_MIN=256 +CONFIG_PTHREAD_STACK_DEFAULT=2048 +CONFIG_HEAP_BASE= +CONFIG_HEAP_SIZE= diff --git a/nuttx/configs/lpcxpresso-lpc1768/usbstorage/ld.script b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/ld.script new file mode 100755 index 000000000..bc431cb94 --- /dev/null +++ b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/ld.script @@ -0,0 +1,110 @@ +/**************************************************************************** + * configs/lpcxpresso-lpc1768/usbstorage/ld.script + * + * Copyright (C) 2011 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The LPC1768 has 512Kb of FLASH beginning at address 0x0000:0000 and + * 64Kb of total SRAM: 32Kb of SRAM in the CPU block beginning at address + * 0x10000000 and 32Kb of AHB SRAM in two banks of 16Kb beginning at addresses + * 0x20070000 and 0x20080000. Here we assume that .data and .bss will all fit + * into the 32Kb CPU SRAM address range. + */ + +MEMORY +{ + flash (rx) : ORIGIN = 0x00000000, LENGTH = 512K + sram (rwx) : ORIGIN = 0x10000000, LENGTH = 32K +} + +OUTPUT_ARCH(arm) +ENTRY(_stext) +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.glue_7) + *(.glue_7t) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + } > flash + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .ARM.extab : { + *(.ARM.extab*) + } >sram + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } >sram + __exidx_end = ABSOLUTE(.); + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/nuttx/configs/lpcxpresso-lpc1768/usbstorage/setenv.sh b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/setenv.sh new file mode 100755 index 000000000..4a6b1613d --- /dev/null +++ b/nuttx/configs/lpcxpresso-lpc1768/usbstorage/setenv.sh @@ -0,0 +1,59 @@ +#!/bin/bash +# configs/lpcxpresso-lpc1768/usbstorage/setenv.sh +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# + +if [ "$(basename $0)" = "setenv.sh" ] ; then + echo "You must source this script, not run it!" 1>&2 + exit 1 +fi + +if [ -z "${PATH_ORIG}" ]; then export PATH_ORIG="${PATH}"; fi + +WD=`pwd` + +# This is where the buildroot might reside on a Linux or Cygwin system +# export TOOLCHAIN_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin" + +# This is the default install location for Code Red on Linux +export TOOLCHAIN_BIN="/usr/local/LPCXpresso/tools/bin" + +# This the Cygwin path to the LPCXpresso 3.6 install location under Windows +#export TOOLCHAIN_BIN="/cygdrive/c/nxp/lpcxpresso_3.6/Tools/bin" + +# This is the path to the LPCXpression tool subdirectory +export LPCTOOL_DIR="${WD}/configs/lpcxpresso-lpc1768/tools" + +# Add the path to the toolchain to the PATH varialble +export PATH="${TOOLCHAIN_BIN}:${LPCTOOL_DIR}:/sbin:/usr/sbin:${PATH_ORIG}" + +echo "PATH : ${PATH}" diff --git a/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig b/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig index c7ecd0187..7b9168599 100755 --- a/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig +++ b/nuttx/configs/olimex-lpc1766stk/usbstorage/defconfig @@ -64,7 +64,7 @@ # CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that # cause a 100 second delay during boot-up. This 100 second delay # serves no purpose other than it allows you to calibrate -# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure +# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure # the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until # the delay actually is 100 seconds. # CONFIG_ARCH_DMA - Support DMA initialization -- cgit v1.2.3