/**************************************************************************** * arch/arm/src/lpc17xx/lpc17_serial.c * * Copyright (C) 2010 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include "chip.h" #include "up_arch.h" #include "os_internal.h" #include "up_internal.h" #include "lpc17_uart.h" #include "lpc17_serial.h" /**************************************************************************** * Pre-processor definitions ****************************************************************************/ /* If we are not using the serial driver for the console, then we still must * provide some minimal implementation of up_putc. */ #if defined(CONFIG_USE_SERIALDRIVER) && defined(HAVE_UART) /* Configuration *********************************************************************/ /**************************************************************************** * Private Types ****************************************************************************/ struct up_dev_s { uint32_t uartbase; /* Base address of UART registers */ uint32_t baud; /* Configured baud */ uint8_t ier; /* Saved IER value */ uint8_t irq; /* IRQ associated with this UART */ uint8_t parity; /* 0=none, 1=odd, 2=even */ uint8_t bits; /* Number of bits (7 or 8) */ uint8_t cclkdiv; /* Divisor needed to get PCLK from CCLK */ bool stopbits2; /* true: Configure with 2 stop bits instead of 1 */ }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ static int up_setup(struct uart_dev_s *dev); static void up_shutdown(struct uart_dev_s *dev); static int up_attach(struct uart_dev_s *dev); static void up_detach(struct uart_dev_s *dev); static int up_interrupt(int irq, void *context); static int up_ioctl(struct file *filep, int cmd, unsigned long arg); static int up_receive(struct uart_dev_s *dev, uint32_t *status); static void up_rxint(struct uart_dev_s *dev, bool enable); static bool up_rxavailable(struct uart_dev_s *dev); static void up_send(struct uart_dev_s *dev, int ch); static void up_txint(struct uart_dev_s *dev, bool enable); static bool up_txready(struct uart_dev_s *dev); static bool up_txempty(struct uart_dev_s *dev); /**************************************************************************** * Private Variables ****************************************************************************/ struct uart_ops_s g_uart_ops = { .setup = up_setup, .shutdown = up_shutdown, .attach = up_attach, .detach = up_detach, .ioctl = up_ioctl, .receive = up_receive, .rxint = up_rxint, .rxavailable = up_rxavailable, .send = up_send, .txint = up_txint, .txready = up_txready, .txempty = up_txempty, }; /* I/O buffers */ #ifdef CONFIG_LPC17_UART0 static char g_uart0rxbuffer[CONFIG_UART0_RXBUFSIZE]; static char g_uart0txbuffer[CONFIG_UART0_TXBUFSIZE]; #endif #ifdef CONFIG_LPC17_UART1 static char g_uart1rxbuffer[CONFIG_UART1_RXBUFSIZE]; static char g_uart1txbuffer[CONFIG_UART1_TXBUFSIZE]; #endif #ifdef CONFIG_LPC17_UART2 static char g_uart2rxbuffer[CONFIG_UART1_RXBUFSIZE]; static char g_uart2txbuffer[CONFIG_UART1_TXBUFSIZE]; #endif #ifdef CONFIG_LPC17_UART3 static char g_uart3rxbuffer[CONFIG_UART1_RXBUFSIZE]; static char g_uart3txbuffer[CONFIG_UART1_TXBUFSIZE]; #endif /* This describes the state of the LPC17xx uart0 port. */ #ifdef CONFIG_LPC17_UART0 static struct up_dev_s g_uart0priv = { .uartbase = LPC17_UART0_BASE, .baud = CONFIG_UART0_BAUD, .irq = LPC17_IRQ_UART0, .parity = CONFIG_UART0_PARITY, .bits = CONFIG_UART0_BITS, .stopbits2 = CONFIG_UART0_2STOP, }; static uart_dev_t g_uart0port = { .recv = { .size = CONFIG_UART0_RXBUFSIZE, .buffer = g_uart0rxbuffer, }, .xmit = { .size = CONFIG_UART0_TXBUFSIZE, .buffer = g_uart0txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart0priv, }; #endif /* This describes the state of the LPC17xx uart1 port. */ #ifdef CONFIG_LPC17_UART1 static struct up_dev_s g_uart1priv = { .uartbase = LPC17_UART1_BASE, .baud = CONFIG_UART1_BAUD, .irq = LPC17_IRQ_UART1, .parity = CONFIG_UART1_PARITY, .bits = CONFIG_UART1_BITS, .stopbits2 = CONFIG_UART1_2STOP, }; static uart_dev_t g_uart1port = { .recv = { .size = CONFIG_UART1_RXBUFSIZE, .buffer = g_uart1rxbuffer, }, .xmit = { .size = CONFIG_UART1_TXBUFSIZE, .buffer = g_uart1txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart1priv, }; #endif /* This describes the state of the LPC17xx uart1 port. */ #ifdef CONFIG_LPC17_UART2 static struct up_dev_s g_uart2priv = { .uartbase = LPC17_UART2_BASE, .baud = CONFIG_UART2_BAUD, .irq = LPC17_IRQ_UART2, .parity = CONFIG_UART2_PARITY, .bits = CONFIG_UART2_BITS, .stopbits2 = CONFIG_UART2_2STOP, }; static uart_dev_t g_uart2port = { .recv = { .size = CONFIG_UART2_RXBUFSIZE, .buffer = g_uart2rxbuffer, }, .xmit = { .size = CONFIG_UART2_TXBUFSIZE, .buffer = g_uart2txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart2priv, }; #endif /* This describes the state of the LPC17xx uart1 port. */ #ifdef CONFIG_LPC17_UART3 static struct up_dev_s g_uart3priv = { .uartbase = LPC17_UART3_BASE, .baud = CONFIG_UART3_BAUD, .irq = LPC17_IRQ_UART3, .parity = CONFIG_UART3_PARITY, .bits = CONFIG_UART3_BITS, .stopbits2 = CONFIG_UART3_2STOP, }; static uart_dev_t g_uart3port = { .recv = { .size = CONFIG_UART3_RXBUFSIZE, .buffer = g_uart3rxbuffer, }, .xmit = { .size = CONFIG_UART3_TXBUFSIZE, .buffer = g_uart3txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart3priv, }; #endif /* Which UART with be tty0/console and which tty1? tty2? tty3? */ #if defined(CONFIG_UART0_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart0port /* UART0=console */ # define TTYS0_DEV g_uart0port /* UART0=ttyS0 */ # ifdef CONFIG_LPC17_UART1 # define TTYS1_DEV g_uart1port /* UART0=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_LPC17_UART2 # define TTYS2_DEV g_uart2port /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS2 */ # ifdef CONFIG_LPC17_UART3 # define TTYS3_DEV g_uart3port /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS2;UART3=ttyS3 */ # else undef TTYS3_DEV /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART0=ttyS0;UART1=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART0=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART2 # define TTYS1_DEV g_uart2port /* UART0=ttyS0;UART2=ttyS1;No ttyS3 */ # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART0=ttyS0;UART2=ttyS1;UART3=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART0=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_LPC17_UART3 # define TTYS1_DEV g_uart3port /* UART0=ttyS0;UART3=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART0=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif #elif defined(CONFIG_UART1_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart1port /* UART1=console */ # define TTYS0_DEV g_uart1port /* UART1=ttyS0 */ # ifdef CONFIG_LPC17_UART # define TTYS1_DEV g_uart0port /* UART1=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_LPC17_UART2 # define TTYS2_DEV g_uart2port /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS2 */ # ifdef CONFIG_LPC17_UART3 # define TTYS3_DEV g_uart3port /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS2;UART3=ttyS3 */ # else # undef TTYS3_DEV /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART1=ttyS0;UART0=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART1=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART2 # define TTYS1_DEV g_uart2port /* UART1=ttyS0;UART2=ttyS1 */ # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART1=ttyS0;UART2=ttyS1;UART3=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART1=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_LPC17_UART3 # define TTYS1_DEV g_uart3port /* UART1=ttyS0;UART3=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART1=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif #elif defined(CONFIG_UART2_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart2port /* UART2=console */ # define TTYS0_DEV g_uart2port /* UART2=ttyS0 */ # ifdef CONFIG_LPC17_UART # define TTYS1_DEV g_uart0port /* UART2=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_LPC17_UART1 # define TTYS2_DEV g_uart1port /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS2 */ # ifdef CONFIG_LPC17_UART3 # define TTYS3_DEV g_uart3port /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS2;UART3=ttyS3 */ # else # undef TTYS3_DEV /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART2=ttyS0;UART0=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART2=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART1 # define TTYS1_DEV g_uart1port /* UART2=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_LPC17_UART3 # define TTYS2_DEV g_uart3port /* UART2=ttyS0;UART1=ttyS1;UART3=ttyS2 */ # else # undef TTYS2_DEV /* UART2=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_LPC17_UART3 # define TTYS1_DEV g_uart3port /* UART2=ttyS0;UART3=ttyS1;No ttyS3 */ # else # undef TTYS1_DEV /* UART2=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif #elif defined(CONFIG_UART3_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart3port /* UART3=console */ # define TTYS0_DEV g_uart3port /* UART3=ttyS0 */ # ifdef CONFIG_LPC17_UART # define TTYS1_DEV g_uart0port /* UART3=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_LPC17_UART1 # define TTYS2_DEV g_uart1port /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS2 */ # ifdef CONFIG_LPC17_UART2 # define TTYS3_DEV g_uart2port /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS2;UART2=ttyS3 */ # else # undef TTYS3_DEV /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART2 # define TTYS2_DEV g_uart2port /* UART3=ttyS0;UART0=ttyS1;UART2=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART3=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_LPC17_UART1 # define TTYS1_DEV g_uart1port /* UART3=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_LPC17_UART2 # define TTYS2_DEV g_uart2port /* UART3=ttyS0;UART1=ttyS1;UART2=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART3=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_LPC17_UART2 # define TTYS1_DEV g_uart2port /* UART3=ttyS0;UART2=ttyS1;No ttyS3;No ttyS3 */ # undef TTYS3_DEV /* UART3=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART3=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif #endif /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: up_serialin ****************************************************************************/ static inline uint8_t up_serialin(struct up_dev_s *priv, int offset) { return getreg8(priv->uartbase + offset); } /**************************************************************************** * Name: up_serialout ****************************************************************************/ static inline void up_serialout(struct up_dev_s *priv, int offset, uint8_t value) { putreg8(value, priv->uartbase + offset); } /**************************************************************************** * Name: up_disableuartint ****************************************************************************/ static inline void up_disableuartint(struct up_dev_s *priv, uint8_t *ier) { if (ier) { *ier = priv->ier & UART_IER_ALLIE; } priv->ier &= ~UART_IER_ALLIE; up_serialout(priv, LPC17_UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: up_restoreuartint ****************************************************************************/ static inline void up_restoreuartint(struct up_dev_s *priv, uint8_t ier) { priv->ier |= ier & UART_IER_ALLIE; up_serialout(priv, LPC17_UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: up_enablebreaks ****************************************************************************/ static inline void up_enablebreaks(struct up_dev_s *priv, bool enable) { uint8_t lcr = up_serialin(priv, LPC17_UART_LCR_OFFSET); if (enable) { lcr |= UART_LCR_BRK; } else { lcr &= ~UART_LCR_BRK; } up_serialout(priv, LPC17_UART_LCR_OFFSET, lcr); } /**************************************************************************** * Name: up_setup * * Description: * Configure the UART baud, bits, parity, fifos, etc. This * method is called the first time that the serial port is * opened. * ****************************************************************************/ static int up_setup(struct uart_dev_s *dev) { #ifndef CONFIG_SUPPRESS_LPC17_UART_CONFIG struct up_dev_s *priv = (struct up_dev_s*)dev->priv; uint16_t dl; uint8_t lcr; /* Clear fifos */ up_serialout(priv, LPC17_UART_FCR_OFFSET, (UART_FCR_RXRST|UART_FCR_TXRST)); /* Set trigger */ up_serialout(priv, LPC17_UART_FCR_OFFSET, (UART_FCR_FIFOEN|UART_FCR_RXTRIGGER_8)); /* Set up the IER */ priv->ier = up_serialin(priv, LPC17_UART_IER_OFFSET); /* Set up the LCR */ lcr = 0; if (priv->bits == 7) { lcr |= UART_LCR_WLS_7BIT; } else { lcr |= UART_LCR_WLS_8BIT; } if (priv->stopbits2) { lcr |= UART_LCR_STOP; } if (priv->parity == 1) { lcr |= (UART_LCR_PE|UART_LCR_PS_ODD); } else if (priv->parity == 2) { lcr |= (UART_LCR_PE|UART_LCR_PS_EVEN); } /* Enter DLAB=1 */ up_serialout(priv, LPC17_UART_LCR_OFFSET, (lcr | UART_LCR_DLAB)); /* Set the BAUD divisor */ dl = lpc17_uartdl(priv->baud, priv->cclkdiv); up_serialout(priv, LPC17_UART_DLM_OFFSET, dl >> 8); up_serialout(priv, LPC17_UART_DLL_OFFSET, dl & 0xff); /* Clear DLAB */ up_serialout(priv, LPC17_UART_LCR_OFFSET, lcr); /* Configure the FIFOs */ up_serialout(priv, LPC17_UART_FCR_OFFSET, (UART_FCR_RXTRIGGER_8|UART_FCR_TXRST|UART_FCR_RXRST|UART_FCR_FIFOEN)); /* The NuttX serial driver waits for the first THRE interrrupt before * sending serial data... However, it appears that the lpc17xx hardware * does not generate that interrupt until a transition from not-empty * to empty. So, the current kludge here is to send one NULL at * startup to kick things off. */ up_serialout(priv, LPC17_UART_THR_OFFSET, '\0'); #endif return OK; } /**************************************************************************** * Name: up_shutdown * * Description: * Disable the UART. This method is called when the serial * port is closed * ****************************************************************************/ static void up_shutdown(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; up_disableuartint(priv, NULL); } /**************************************************************************** * Name: up_attach * * Description: * Configure the UART to operation in interrupt driven mode. This method is * called when the serial port is opened. Normally, this is just after the * the setup() method is called, however, the serial console may operate in * a non-interrupt driven mode during the boot phase. * * RX and TX interrupts are not enabled when by the attach method (unless the * hardware supports multiple levels of interrupt enabling). The RX and TX * interrupts are not enabled until the txint() and rxint() methods are called. * ****************************************************************************/ static int up_attach(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; int ret; /* Attach and enable the IRQ */ ret = irq_attach(priv->irq, up_interrupt); if (ret == OK) { /* Enable the interrupt (RX and TX interrupts are still disabled * in the UART */ up_enable_irq(priv->irq); } return ret; } /**************************************************************************** * Name: up_detach * * Description: * Detach UART interrupts. This method is called when the serial port is * closed normally just before the shutdown method is called. The exception is * the serial console which is never shutdown. * ****************************************************************************/ static void up_detach(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; up_disable_irq(priv->irq); irq_detach(priv->irq); } /**************************************************************************** * Name: up_interrupt * * Description: * This is the UART interrupt handler. It will be invoked * when an interrupt received on the 'irq' It should call * uart_transmitchars or uart_receivechar to perform the * appropriate data transfers. The interrupt handling logic\ * must be able to map the 'irq' number into the approprite * uart_dev_s structure in order to call these functions. * ****************************************************************************/ static int up_interrupt(int irq, void *context) { struct uart_dev_s *dev = NULL; struct up_dev_s *priv; uint8_t status; int passes; if (g_uart1priv.irq == irq) { dev = &g_uart1port; } else if (g_uart0priv.irq == irq) { dev = &g_uart0port; } else { PANIC(OSERR_INTERNAL); } priv = (struct up_dev_s*)dev->priv; /* Loop until there are no characters to be transferred or, * until we have been looping for a long time. */ for (passes = 0; passes < 256; passes++) { /* Get the current UART status and check for loop * termination conditions */ status = up_serialin(priv, LPC17_UART_IIR_OFFSET); /* The UART_IIR_INTSTATUS bit should be zero if there are pending * interrupts */ if ((status & UART_IIR_INTSTATUS) != 0) { /* Break out of the loop when there is no longer a * pending interrupt */ break; } /* Handle the interrupt by its interrupt ID field */ switch (status & UART_IIR_INTID_MASK) { /* Handle incoming, receive bytes (with or without timeout) */ case UART_IIR_INTID_RDA: case UART_IIR_INTID_CTI: { uart_recvchars(dev); break; } /* Handle outgoing, transmit bytes */ case UART_IIR_INTID_THRE: { uart_xmitchars(dev); break; } /* Just clear modem status interrupts (UART1 only) */ case UART_IIR_INTID_MSI: { /* Read the modem status register (MSR) to clear */ status = up_serialin(priv, LPC17_UART_MSR_OFFSET); vdbg("MSR: %02x\n", status); break; } /* Just clear any line status interrupts */ case UART_IIR_INTID_RLS: { /* Read the line status register (LSR) to clear */ status = up_serialin(priv, LPC17_UART_LSR_OFFSET); vdbg("LSR: %02x\n", status); break; } /* There should be no other values */ default: { dbg("Unexpected IIR: %02x\n", status); break; } } } return OK; } /**************************************************************************** * Name: up_ioctl * * Description: * All ioctl calls will be routed through this method * ****************************************************************************/ static int up_ioctl(struct file *filep, int cmd, unsigned long arg) { struct inode *inode = filep->f_inode; struct uart_dev_s *dev = inode->i_private; struct up_dev_s *priv = (struct up_dev_s*)dev->priv; int ret = OK; switch (cmd) { case TIOCSERGSTRUCT: { struct up_dev_s *user = (struct up_dev_s*)arg; if (!user) { *get_errno_ptr() = EINVAL; ret = ERROR; } else { memcpy(user, dev, sizeof(struct up_dev_s)); } } break; case TIOCSBRK: /* BSD compatibility: Turn break on, unconditionally */ { irqstate_t flags = irqsave(); up_enablebreaks(priv, true); irqrestore(flags); } break; case TIOCCBRK: /* BSD compatibility: Turn break off, unconditionally */ { irqstate_t flags; flags = irqsave(); up_enablebreaks(priv, false); irqrestore(flags); } break; default: *get_errno_ptr() = ENOTTY; ret = ERROR; break; } return ret; } /**************************************************************************** * Name: up_receive * * Description: * Called (usually) from the interrupt level to receive one * character from the UART. Error bits associated with the * receipt are provided in the return 'status'. * ****************************************************************************/ static int up_receive(struct uart_dev_s *dev, uint32_t *status) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; uint8_t rbr; *status = up_serialin(priv, LPC17_UART_LSR_OFFSET); rbr = up_serialin(priv, LPC17_UART_RBR_OFFSET); return rbr; } /**************************************************************************** * Name: up_rxint * * Description: * Call to enable or disable RX interrupts * ****************************************************************************/ static void up_rxint(struct uart_dev_s *dev, bool enable) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; if (enable) { #ifndef CONFIG_SUPPRESS_SERIAL_INTS priv->ier |= UART_IER_RBRIE; #endif } else { priv->ier &= ~UART_IER_RBRIE; } up_serialout(priv, LPC17_UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: up_rxavailable * * Description: * Return true if the receive fifo is not empty * ****************************************************************************/ static bool up_rxavailable(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; return ((up_serialin(priv, LPC17_UART_LSR_OFFSET) & UART_LSR_RDR) != 0); } /**************************************************************************** * Name: up_send * * Description: * This method will send one byte on the UART * ****************************************************************************/ static void up_send(struct uart_dev_s *dev, int ch) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; up_serialout(priv, LPC17_UART_THR_OFFSET, (uint8_t)ch); } /**************************************************************************** * Name: up_txint * * Description: * Call to enable or disable TX interrupts * ****************************************************************************/ static void up_txint(struct uart_dev_s *dev, bool enable) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; if (enable) { #ifndef CONFIG_SUPPRESS_SERIAL_INTS priv->ier |= UART_IER_THREIE; #endif } else { priv->ier &= ~UART_IER_THREIE; } up_serialout(priv, LPC17_UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: up_txready * * Description: * Return true if the tranmsit fifo is not full * ****************************************************************************/ static bool up_txready(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; return ((up_serialin(priv, LPC17_UART_LSR_OFFSET) & UART_LSR_THRE) != 0); } /**************************************************************************** * Name: up_txempty * * Description: * Return true if the transmit fifo is empty * ****************************************************************************/ static bool up_txempty(struct uart_dev_s *dev) { struct up_dev_s *priv = (struct up_dev_s*)dev->priv; return ((up_serialin(priv, LPC17_UART_LSR_OFFSET) & UART_LSR_THRE) != 0); } /**************************************************************************** * Public Funtions ****************************************************************************/ /**************************************************************************** * Name: up_serialinit * * Description: * Performs the low level UART initialization early in debug so that the * serial console will be available during bootup. This must be called * before up_serialinit. * * NOTE: Power, clocking, and pin configuration was performed in * up_lowsetup() very, early in the boot sequence. * ****************************************************************************/ void up_earlyserialinit(void) { /* Disable all UARTS */ #ifdef TTYS0_DEV TTYS0_DEV.cclkdiv = lpc17_uartcclkdiv(CONFIG_UART0_BAUD); up_disableuartint(TTYS0_DEV.priv, NULL); #endif #ifdef TTYS1_DEV TTYS1_DEV.cclkdiv = lpc17_uartcclkdiv(CONFIG_UART1_BAUD); up_disableuartint(TTYS1_DEV.priv, NULL); #endif #ifdef TTYS2_DEV TTYS2_DEV.cclkdiv = lpc17_uartcclkdiv(CONFIG_UART2_BAUD); up_disableuartint(TTYS2_DEV.priv, NULL); #endif #ifdef TTYS3_DEV TTYS3_DEV.cclkdiv = lpc17_uartcclkdiv(CONFIG_UART3_BAUD); up_disableuartint(TTYS3_DEV.priv, NULL); #endif /* Configuration whichever one is the console */ #ifdef CONSOLE_DEV CONSOLE_DEV.isconsole = true; up_setup(&CONSOLE_DEV); #endif } /**************************************************************************** * Name: up_serialinit * * Description: * Register serial console and serial ports. This assumes that * up_earlyserialinit was called previously. * ****************************************************************************/ void up_serialinit(void) { #ifdef CONSOLE_DEV (void)uart_register("/dev/console", &CONSOLE_DEV); #endif #ifdef TTYS0_DEV (void)uart_register("/dev/ttyS0", &TTYS0_DEV); #endif #ifdef TTYS1_DEV (void)uart_register("/dev/ttyS1", &TTYS1_DEV); #endif #ifdef TTYS2_DEV (void)uart_register("/dev/ttyS2", &TTYS2_DEV); #endif #ifdef TTYS3_DEV (void)uart_register("/dev/ttyS3", &TTYS3_DEV); #endif } /**************************************************************************** * Name: up_putc * * Description: * Provide priority, low-level access to support OS debug writes * ****************************************************************************/ int up_putc(int ch) { struct up_dev_s *priv = (struct up_dev_s*)CONSOLE_DEV.priv; uint8_t ier; up_disableuartint(priv, &ier); /* Check for LF */ if (ch == '\n') { /* Add CR */ up_lowputc('\r'); } up_lowputc(ch); up_restoreuartint(priv, ier); return ch; } #else /* CONFIG_USE_SERIALDRIVER */ /**************************************************************************** * Name: up_putc * * Description: * Provide priority, low-level access to support OS debug writes * ****************************************************************************/ int up_putc(int ch) { #ifdef HAVE_UART /* Check for LF */ if (ch == '\n') { /* Add CR */ up_lowputc('\r'); } up_lowputc(ch); #endif return ch; } #endif /* CONFIG_USE_SERIALDRIVER */