README.txt ^^^^^^^^^^ ZDS-II Compiler Versions ^^^^^^^^^^^^^^^^^^^^^^^^ Different configurations have been build for this board using ZDS-11 Versions 4.11.0, 4.11.1, and 5.1.1 You have to check the files */Make.defs to see how the build is configured: Check the definitions of ZDSVERSION (if present) and ZDSINSTALLDIR. NOTE: Different versions of the ZDS-II compiler may also require different versions of .linkcmd and .zdsproj files as well. Version 4.11.0 The 5.1.1 version of the ZDS-II tools are currently configured for all ez80 boards. However, it is the older version 4.11.0 that this code has been verified against. Although it compiles without error, the 4.11.0 compiler generates bad code on one of the files, mm/mm_initialize.c. Below is a simple work- around. --- mm/mm_initialize.c.SAVE 2008-02-13 08:06:46.833857700 -0600 +++ mm/mm_initialize.c 2008-02-13 08:07:26.367608900 -0600 @@ -94,8 +94,11 @@ { int i; +#if 0 /* DO NOT CHECK IN */ CHECK_ALLOCNODE_SIZE; CHECK_FREENODE_SIZE; +#endif /* Set up global variables */ UPDATE: I don't know if 4.11.1 has this same problem (I bet not since I submitted the bug to ZiLOG), but I have permanently worked around the above problem for all ZiLOG compilers. Version 5.1.1 On June 22, 2011 I verified that these configurations build successfully with the 5.1.1 ZDS-II version. On November 12, 2012, all of the configurations were converted to use 5.1.1, but have not been verified on a running target. The above kludge for 4.11.0 is not required with 5.1.1. Paths were also updated that are specific to a 32-bit toolchain running on a 64 bit windows platform. Change to a different toolchain, you will need to modify the versioning in Make.defs and setenv.sh; if you want to build on a different platform, you will need to change the path in the ZDS binaries in those same files. Other Versions If you use any version of ZDS-II other than 5.1.1 or if you install ZDS-II at any location other than the default location, you will have to modify two files: (1) configs/ez80f910200kitg/*/setenv.sh and (2) configs/ez80f910200kitg/*/Make.defs. Configuration Subdirectories ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ src/ and include/ These directories contain common logic for all ez80f910200zco configurations. Variations on the basic ez80f910200zco configuration are maintained in subdirectories. To configure any specific configuration, do the following steps: cd /tools ./configure.sh ez80f910200zco/ cd make Where is the specific board configuration that you wish to build. The following board-specific configurations are available: dhcpd: This builds the DCHP server using the examples/dhcpd application (for execution from FLASH.) See examples/README.txt for information about the dhcpd example. httpd: This builds the uIP web server example using the examples/uip application (for execution from FLASH). See examples/README.txt for information about ostest. ostest This builds the examples/ostest application for execution from FLASH. See examples/README.txt for information about ostest. - ostest This builds the examples/ostest application for execution from FLASH. See examples/README.txt for information about ostest. NOTES: 1. This configuration uses the mconf-based configuration tool. To change this configuration using that tool, you should: a. Build and install the mconf tool. See nuttx/README.txt and misc/tools/ b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process. 2. By default, this configuration assumes that you are using the Cygwin environment on Windows. An option is to use the native CMD.exe window build as described in the top-level README.txt file. To set up that configuration: -CONFIG_WINDOWS_CYGWIN=y +CONFIG_WINDOWS_NATIVE=y And after configuring, make sure that CONFIG_APPS_DIR uses the back slash character. For example: CONFIG_APPS_DIR="..\apps" NOTES: a. If you need to change the toolchain path used in Make.defs, you will need to use the short 8.3 filenames to avoid spaces. On my PC, C:\PROGRA~1\ is is C:\Program Files\ and C:\PROGRA~2\ is C:\Program Files (x86)\ b. You can't use setenv.sh in the native Windows environment. Try scripts/setenv.bat instead. c. At present, the native Windows build fails at the final link stages. The failure is due to problems in arch/z80/src/nuttx.linkcmd that is autogenerated by arch/z80/src/Makefile.zdsii. The basic problem is the spurious spaces and and carrirage returns are generated at the end of the lines after a line continuation (\ ^M). If these trailing bad characters are manually eliminated, then the build will succeed on the next try. nsh This configuratino builds the NuttShell (NSH). That code can be found in examples/nsh. For more information see: examples/nsh/README.txt and Documentation/NuttShell.html. nettest This configuration is used for testing the eZ80F91 EMAC driver. It builds examples/nettest. See examples/README.txt for more information about nettest. poll This configuration is also used for testing the eZ80F91 EMAC driver. It builds examples/poll. See examples/README.txt for more information about the poll test. Check out any README.txt files in these s.