/************************************************************************************ * configs/stm3210e-eval/include/board.h * include/arch/board/board.h * * Copyright (C) 2009 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __ARCH_BOARD_BOARD_H #define __ARCH_BOARD_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif #include "stm32_rcc.h" #include "stm32_sdio.h" #include "stm32_internal.h" /************************************************************************************ * Definitions ************************************************************************************/ /* Clocking *************************************************************************/ /* On-board crystal frequency is 8MHz (HSE) */ #define STM32_BOARD_XTAL 8000000ul /* PLL source is HSE/1, PLL multipler is 9: PLL frequency is 8MHz (XTAL) x 9 = 72MHz */ #define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC #define STM32_CFGR_PLLXTPRE 0 #define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx9 #define STM32_PLL_FREQUENCY (9*STM32_BOARD_XTAL) /* Use the PLL and set the SYSCLK source to be the PLL */ #define STM32_SYSCLK_SW RCC_CFGR_SW_PLL #define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL #define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY /* AHB clock (HCLK) is SYSCLK (72MHz) */ #define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK #define STM32_HCLK_FREQUENCY STM32_PLL_FREQUENCY /* APB2 clock (PCLK2) is HCLK (72MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK #define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY /* APB1 clock (PCLK1) is HCLK/2 (36MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2 #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* USB divider -- Divide PLL clock by 1.5 */ #define STM32_CFGR_USBPRE 0 /* SDIO dividers. Note that slower clocking is required when DMA is disabled * in order to avoid RX overrun/TX underrun errors due to delayed responses * to service FIFOs in interrupt driven mode. These values have not been * tuned!!! * * HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz */ #define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT) /* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz */ #ifdef CONFIG_SDIO_DMA # define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) #else # define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT) #endif /* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz */ #ifdef CONFIG_SDIO_DMA # define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) #else # define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT) #endif /* LED definitions ******************************************************************/ /* The STM3210E-EVAL board has 4 LEDs that we will encode as: */ #define LED_STARTED 0 /* LED1 */ #define LED_HEAPALLOCATE 1 /* LED2 */ #define LED_IRQSENABLED 2 /* LED1 + LED2 */ #define LED_STACKCREATED 3 /* LED3 */ #define LED_INIRQ 4 /* LED1 + LED3 */ #define LED_SIGNAL 5 /* LED2 + LED3 */ #define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */ #define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */ /* The STM3210E-EVAL supports several buttons * * Reset -- Connected to NRST * Wakeup -- Connected to PA.0 * Tamper -- Connected to PC.13 * Key -- Connected to PG.8 * * And a Joystick * * Joystick center -- Connected to PG.7 * Joystick down -- Connected to PD.3 * Joystick left -- Connected to PG.14 * Joystick right -- Connected to PG.13 * Joystick up -- Connected to PG.15 */ #define BUTTON_WAKEUP (1 << 0) #define BUTTON_TAMPER (1 << 1) #define BUTTON_KEY (1 << 2) #define JOYSTICK_SEL (1 << 3) #define JOYSTICK_DOWN (1 << 4) #define JOYSTICK_LEFT (1 << 5) #define JOYSTICK_RIGHT (1 << 6) #define JOYSTICK_UP (1 << 7) #define NUM_BUTTONS 8 /************************************************************************************ * Public Data ************************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /************************************************************************************ * Public Function Prototypes ************************************************************************************/ /************************************************************************************ * Name: stm32_boardinitialize * * Description: * All STM32 architectures must provide the following entry point. This entry point * is called early in the intitialization -- after all memory has been configured * and mapped but before any devices have been initialized. * ************************************************************************************/ EXTERN void stm32_boardinitialize(void); /************************************************************************************ * Button support. * * Description: * up_buttoninit() must be called to initialize button resources. After that, * up_buttons() may be called to collect the state of all buttons. up_buttons() * returns an 8-bit bit set with each bit associated with a button. See the * BUTTON_* and JOYSTICK_* definitions above for the meaning of each bit. * ************************************************************************************/ #ifdef CONFIG_ARCH_BUTTONS EXTERN void up_buttoninit(void); EXTERN uint8_t up_buttons(void); #endif #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __ARCH_BOARD_BOARD_H */