README ====== This README discusses issues unique to NuttX configurations for the STMicro STM32140G-EVAL development board. Contents ======== - Development Environment - GNU Toolchain Options - IDEs - NuttX EABI "buildroot" Toolchain - NuttX OABI "buildroot" Toolchain - NXFLAT Toolchain - STM3240G-EVAL-specific Configuration Options - LEDs - Ethernet - PWM - CAN - FPU - FSMC SRAM - I/O Expanders - STM3240G-EVAL-specific Configuration Options - Configurations Development Environment ======================= Either Linux or Cygwin on Windows can be used for the development environment. The source has been built only using the GNU toolchain (see below). Other toolchains will likely cause problems. Testing was performed using the Cygwin environment because the Raisonance R-Link emulatator and some RIDE7 development tools were used and those tools works only under Windows. GNU Toolchain Options ===================== Toolchain Configurations ------------------------ The NuttX make system has been modified to support the following different toolchain options. 1. The CodeSourcery GNU toolchain, 2. The Atollic Toolchain, 3. The devkitARM GNU toolchain, 4. Raisonance GNU toolchain, or 5. The NuttX buildroot Toolchain (see below). Most testing has been conducted using the CodeSourcery toolchain for Windows and that is the default toolchain in most configurations (FPU-related testing has been performed with the Atolloc toolchain for windows. To use the Atollic, devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to add one of the following configuration options to your .config (or defconfig) file: CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux CONFIG_STM32_ATOLLIC_LITE=y : The free, "Lite" version of Atollic toolchain under Windows CONFIG_STM32_ATOLLIC_PRO=y : The paid, "Pro" version of Atollic toolchain under Windows CONFIG_STM32_DEVKITARM=y : devkitARM under Windows CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default) If you change the default toolchain, then you may also have to modify the PATH in the setenv.h file if your make cannot find the tools. NOTE: the CodeSourcery (for Windows), Atollic, devkitARM, and Raisonance toolchains are Windows native toolchains. The CodeSourcery (for Linux) and NuttX buildroot toolchains are Cygwin and/or Linux native toolchains. There are several limitations to using a Windows based toolchain in a Cygwin environment. The three biggest are: 1. The Windows toolchain cannot follow Cygwin paths. Path conversions are performed automatically in the Cygwin makefiles using the 'cygpath' utility but you might easily find some new path problems. If so, check out 'cygpath -w' 2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links are used in Nuttx (e.g., include/arch). The make system works around these problems for the Windows tools by copying directories instead of linking them. But this can also cause some confusion for you: For example, you may edit a file in a "linked" directory and find that your changes had no effect. That is because you are building the copy of the file in the "fake" symbolic directory. If you use a Windows toolchain, you should get in the habit of making like this: make clean_context all An alias in your .bashrc file might make that less painful. 3. Dependencies are not made when using Windows versions of the GCC. This is because the dependencies are generated using Windows pathes which do not work with the Cygwin make. MKDEP = $(TOPDIR)/tools/mknulldeps.sh The CodeSourcery Toolchain (2009q1) ----------------------------------- The CodeSourcery toolchain (2009q1) does not work with default optimization level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with -Os. The Atollic "Pro" and "Lite" Toolchain -------------------------------------- One problem that I had with the Atollic toolchains is that the provide a gcc.exe and g++.exe in the same bin/ file as their ARM binaries. If the Atollic bin/ path appears in your PATH variable before /usr/bin, then you will get the wrong gcc when you try to build host executables. This will cause to strange, uninterpretable errors build some host binaries in tools/ when you first make. Also, the Atollic toolchains are the only toolchains that have built-in support for the FPU in these configurations. If you plan to use the Cortex-M4 FPU, you will need to use the Atollic toolchain for now. See the FPU section below for more information. The Atollic "Lite" Toolchain ---------------------------- The free, "Lite" version of the Atollic toolchain does not support C++ nor does it support ar, nm, objdump, or objdcopy. If you use the Atollic "Lite" toolchain, you will have to set: CONFIG_HAVE_CXX=n In order to compile successfully. Otherwise, you will get errors like: "C++ Compiler only available in TrueSTUDIO Professional" The make may then fail in some of the post link processing because of some of the other missing tools. The Make.defs file replaces the ar and nm with the default system x86 tool versions and these seem to work okay. Disable all of the following to avoid using objcopy: CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=n CONFIG_MOTOROLA_SREC=n CONFIG_RAW_BINARY=n devkitARM --------- The devkitARM toolchain includes a version of MSYS make. Make sure that the the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM path or will get the wrong version of make. IDEs ==== NuttX is built using command-line make. It can be used with an IDE, but some effort will be required to create the project. Makefile Build -------------- Under Eclipse, it is pretty easy to set up an "empty makefile project" and simply use the NuttX makefile to build the system. That is almost for free under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty makefile project in order to work with Windows (Google for "Eclipse Cygwin" - there is a lot of help on the internet). Native Build ------------ Here are a few tips before you start that effort: 1) Select the toolchain that you will be using in your .config file 2) Start the NuttX build at least one time from the Cygwin command line before trying to create your project. This is necessary to create certain auto-generated files and directories that will be needed. 3) Set up include pathes: You will need include/, arch/arm/src/stm32, arch/arm/src/common, arch/arm/src/armv7-m, and sched/. 4) All assembly files need to have the definition option -D __ASSEMBLY__ on the command line. Startup files will probably cause you some headaches. The NuttX startup file is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX one time from the Cygwin command line in order to obtain the pre-built startup object needed by RIDE. NuttX EABI "buildroot" Toolchain ================================ A GNU GCC-based toolchain is assumed. The files */setenv.sh should be modified to point to the correct path to the Cortex-M3 GCC toolchain (if different from the default in your PATH variable). If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX SourceForge download site (https://sourceforge.net/projects/nuttx/files/buildroot/). This GNU toolchain builds and executes in the Linux or Cygwin environment. 1. You must have already configured Nuttx in /nuttx. cd tools ./configure.sh stm3240g-eval/ 2. Download the latest buildroot package into 3. unpack the buildroot tarball. The resulting directory may have versioning information on it like buildroot-x.y.z. If so, rename /buildroot-x.y.z to /buildroot. 4. cd /buildroot 5. cp configs/cortexm3-eabi-defconfig-4.6.3 .config 6. make oldconfig 7. make 8. Edit setenv.h, if necessary, so that the PATH variable includes the path to the newly built binaries. See the file configs/README.txt in the buildroot source tree. That has more details PLUS some special instructions that you will need to follow if you are building a Cortex-M3 toolchain for Cygwin under Windows. NOTE: Unfortunately, the 4.6.3 EABI toolchain is not compatible with the the NXFLAT tools. See the top-level TODO file (under "Binary loaders") for more information about this problem. If you plan to use NXFLAT, please do not use the GCC 4.6.3 EABI toochain; instead use the GCC 4.3.3 OABI toolchain. See instructions below. NuttX OABI "buildroot" Toolchain ================================ The older, OABI buildroot toolchain is also available. To use the OABI toolchain: 1. When building the buildroot toolchain, either (1) modify the cortexm3-eabi-defconfig-4.6.3 configuration to use EABI (using 'make menuconfig'), or (2) use an exising OABI configuration such as cortexm3-defconfig-4.3.3 2. Modify the Make.defs file to use the OABI conventions: +CROSSDEV = arm-nuttx-elf- +ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft +NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-gotoff.ld -no-check-sections -CROSSDEV = arm-nuttx-eabi- -ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft -NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections NXFLAT Toolchain ================ If you are *not* using the NuttX buildroot toolchain and you want to use the NXFLAT tools, then you will still have to build a portion of the buildroot tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can be downloaded from the NuttX SourceForge download site (https://sourceforge.net/projects/nuttx/files/). This GNU toolchain builds and executes in the Linux or Cygwin environment. 1. You must have already configured Nuttx in /nuttx. cd tools ./configure.sh lpcxpresso-lpc1768/ 2. Download the latest buildroot package into 3. unpack the buildroot tarball. The resulting directory may have versioning information on it like buildroot-x.y.z. If so, rename /buildroot-x.y.z to /buildroot. 4. cd /buildroot 5. cp configs/cortexm3-defconfig-nxflat .config 6. make oldconfig 7. make 8. Edit setenv.h, if necessary, so that the PATH variable includes the path to the newly builtNXFLAT binaries. Ethernet ======== The Ethernet driver is configured to use the MII interface: Board Jumper Settings: Jumper Description JP8 To enable MII, JP8 should not be fitted. JP6 2-3: Enable MII interface mode JP5 2-3: Provide 25 MHz clock for MII or 50 MHz clock for RMII by MCO at PA8 SB1 Not used with MII LEDs ==== The STM3240G-EVAL board has four LEDs labeled LD1, LD2, LD3 and LD4 on the board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is defined. In that case, the usage by the board port is defined in include/board.h and src/up_leds.c. The LEDs are used to encode OS-related\ events as follows: SYMBOL Meaning LED1* LED2 LED3 LED4 ------------------- ----------------------- ------- ------- ------- ------ LED_STARTED NuttX has been started ON OFF OFF OFF LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF LED_IRQSENABLED Interrupts enabled ON ON OFF OFF LED_STACKCREATED Idle stack created OFF OFF ON OFF LED_INIRQ In an interrupt** ON N/C N/C OFF LED_SIGNAL In a signal handler*** N/C ON N/C OFF LED_ASSERTION An assertion failed ON ON N/C OFF LED_PANIC The system has crashed N/C N/C N/C ON LED_IDLE STM32 is is sleep mode (Optional, not used) * If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot and these LEDs will give you some indication of where the failure was ** The normal state is LED3 ON and LED1 faintly glowing. This faint glow is because of timer interupts that result in the LED being illuminated on a small proportion of the time. *** LED2 may also flicker normally if signals are processed. PWM === The STM3240G-Eval has no real on-board PWM devices, but the board can be configured to output a pulse train using timer output pins. The following pins have been use to generate PWM output (see board.h for some other candidates): TIM4 CH2. Pin PD13 is used by the FSMC (FSMC_A18) and is also connected to the Motor Control Connector (CN5) just for this purpose. If FSMC is not enabled, then FSMC_A18 will not be used (and will be tri-stated from the LCD). CONFIGURATION: CONFIG_STM32_TIM4=y CONFIG_PWM=n CONFIG_PWM_PULSECOUNT=n CONFIG_STM32_TIM4_PWM=y CONFIG_STM32_TIM4_CHANNEL=2 ACCESS: Daughterboard Extension Connector, CN3, pin 32 Ground is available on CN3, pin1 NOTE: TIM4 hardware will not support pulse counting. TIM8 CH4: Pin PC9 is used by the microSD card (MicroSDCard_D1) and I2S (I2S_CKIN) but can be completely disconnected from both by opening JP16. CONFIGURATION: CONFIG_STM32_TIM8=y CONFIG_PWM=n CONFIG_PWM_PULSECOUNT=y CONFIG_STM32_TIM8_PWM=y CONFIG_STM32_TIM8_CHANNEL=4 ACCESS: Daughterboard Extension Connector, CN3, pin 17 Ground is available on CN3, pin1 CAN === Connector 10 (CN10) is DB-9 male connector that can be used with CAN1 or CAN2. JP10 connects CAN1_RX or CAN2_RX to the CAN transceiver JP3 connects CAN1_TX or CAN2_TX to the CAN transceiver CAN signals are then available on CN10 pins: CN10 Pin 7 = CANH CN10 Pin 2 = CANL Mapping to STM32 GPIO pins: PD0 = FSMC_D2 & CAN1_RX PD1 = FSMC_D3 & CAN1_TX PB13 = ULPI_D6 & CAN2_TX PB5 = ULPI_D7 & CAN2_RX Configuration Options: CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or CONFIG_STM32_CAN2 must also be defined) CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default Standard 11-bit IDs. CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages. Default: 8 CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests. Default: 4 CONFIG_STM32_CAN1 - Enable support for CAN1 CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined. CONFIG_STM32_CAN2 - Enable support for CAN2 CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined. CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7 CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an dump of all CAN registers. FPU === FPU Configuration Options ------------------------- There are two version of the FPU support built into the STM32 port. 1. Lazy Floating Point Register Save. This is an untested implementation that saves and restores FPU registers only on context switches. This means: (1) floating point registers are not stored on each context switch and, hence, possibly better interrupt performance. But, (2) since floating point registers are not saved, you cannot use floating point operations within interrupt handlers. This logic can be enabled by simply adding the following to your .config file: CONFIG_ARCH_FPU=y 2. Non-Lazy Floating Point Register Save Mike Smith has contributed an extensive re-write of the ARMv7-M exception handling logic. This includes verified support for the FPU. These changes have not yet been incorporated into the mainline and are still considered experimental. These FPU logic can be enabled with: CONFIG_ARCH_FPU=y CONFIG_ARMV7M_CMNVECTOR=y You will probably also changes to the scripts/ld.script in if this option is selected. This should work: -ENTRY(_stext) +ENTRY(__start) /* Treat __start as the anchor for dead code stripping */ +EXTERN(_vectors) /* Force the vectors to be included in the output */ CFLAGS ------ Only the Atollic toolchain has built-in support for the Cortex-M4 FPU. You will see the following lines in each Make.defs file: ifeq ($(CONFIG_STM32_ATOLLIC_LITE),y) # Atollic toolchain under Windows ... ifeq ($(CONFIG_ARCH_FPU),y) ARCHCPUFLAGS = -mcpu=cortex-m4 -mthumb -march=armv7e-m -mfpu=fpv4-sp-d16 -mfloat-abi=hard else ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft endif endif If you are using a toolchain other than the Atollic toolchain, then to use the FPU you will also have to modify the CFLAGS to enable compiler support for the ARMv7-M FPU. As of this writing, there are not many GCC toolchains that will support the ARMv7-M FPU. As a minimum you will need to add CFLAG options to (1) enable hardware floating point code generation, and to (2) select the FPU implementation. You might try the same options as used with the Atollic toolchain in the Make.defs file: ARCHCPUFLAGS = -mcpu=cortex-m4 -mthumb -march=armv7e-m -mfpu=fpv4-sp-d16 -mfloat-abi=hard Configuration Changes --------------------- Below are all of the configuration changes that I had to make to configs/stm3240g-eval/nsh2 in order to successfully build NuttX using the Atollic toolchain WITH FPU support: -CONFIG_ARCH_FPU=n : Enable FPU support +CONFIG_ARCH_FPU=y -CONFIG_STM32_CODESOURCERYW=y : Disable the CodeSourcery toolchain +CONFIG_STM32_CODESOURCERYW=n -CONFIG_STM32_ATOLLIC_LITE=n : Enable *one* the Atollic toolchains CONFIG_STM32_ATOLLIC_PRO=n -CONFIG_STM32_ATOLLIC_LITE=y : The "Lite" version, OR CONFIG_STM32_ATOLLIC_PRO=y : The "Pro" version (not both) -CONFIG_INTELHEX_BINARY=y : Suppress generation FLASH download formats +CONFIG_INTELHEX_BINARY=n : (Only necessary with the "Lite" version) -CONFIG_HAVE_CXX=y : Suppress generation of C++ code +CONFIG_HAVE_CXX=n : (Only necessary with the "Lite" version) See the section above on Toolchains, NOTE 2, for explanations for some of the configuration settings. Some of the usual settings are just not supported by the "Lite" version of the Atollic toolchain. FSMC SRAM ========= On-board SRAM ------------- A 16 Mbit SRAM is connected to the STM32F407IGH6 FSMC bus which shares the same I/Os with the CAN1 bus. Jumper settings: JP1: Connect PE4 to SRAM as A20 JP2: onnect PE3 to SRAM as A19 JP3 and JP10 must not be fitted for SRAM and LCD application. JP3 and JP10 select CAN1 or CAN2 if fitted; neither if not fitted. The on-board SRAM can be configured by setting CONFIG_STM32_FSMC=y CONFIG_STM32_FSMC_SRAM=y CONFIG_HEAP2_BASE=0x64000000 CONFIG_HEAP2_SIZE=2097152 CONFIG_MM_REGIONS=2 (or =3, see below) Configuration Options --------------------- Internal SRAM is available in all members of the STM32 family. The F4 family also contains internal CCM SRAM. This SRAM is different because it cannot be used for DMA. So if DMA needed, then the following should be defined to exclude CCM SRAM from the heap: CONFIG_STM32_CCMEXCLUDE : Exclude CCM SRAM from the HEAP In addition to internal SRAM, SRAM may also be available through the FSMC. In order to use FSMC SRAM, the following additional things need to be present in the NuttX configuration file: CONFIG_STM32_FSMC=y : Enables the FSMC CONFIG_STM32_FSMC_SRAM=y : Indicates that SRAM is available via the FSMC (as opposed to an LCD or FLASH). CONFIG_HEAP2_BASE : The base address of the SRAM in the FSMC address space CONFIG_HEAP2_SIZE : The size of the SRAM in the FSMC address space CONFIG_MM_REGIONS : Must be set to a large enough value to include the FSMC SRAM SRAM Configurations ------------------- There are 4 possible SRAM configurations: Configuration 1. System SRAM (only) CONFIG_MM_REGIONS == 1 CONFIG_STM32_FSMC_SRAM NOT defined CONFIG_STM32_CCMEXCLUDE defined Configuration 2. System SRAM and CCM SRAM CONFIG_MM_REGIONS == 2 CONFIG_STM32_FSMC_SRAM NOT defined CONFIG_STM32_CCMEXCLUDE NOT defined Configuration 3. System SRAM and FSMC SRAM CONFIG_MM_REGIONS == 2 CONFIG_STM32_FSMC_SRAM defined CONFIG_STM32_CCMEXCLUDE defined Configuration 4. System SRAM, CCM SRAM, and FSMC SRAM CONFIG_MM_REGIONS == 3 CONFIG_STM32_FSMC_SRAM defined CONFIG_STM32_CCMEXCLUDE NOT defined I/O Expanders ============= The STM3240G-EVAL has two STMPE811QTR I/O expanders on board both connected to the STM32 via I2C1. They share a common interrupt line: PI2. STMPE811 U24, I2C address 0x41 (7-bit) ------ ---- ---------------- -------------------------------------------- STPE11 PIN BOARD SIGNAL BOARD CONNECTION ------ ---- ---------------- -------------------------------------------- Y- TouchScreen_Y- LCD Connector XL X- TouchScreen_X- LCD Connector XR Y+ TouchScreen_Y+ LCD Connector XD X+ TouchScreen_X+ LCD Connector XU IN3 EXP_IO9 IN2 EXP_IO10 IN1 EXP_IO11 IN0 EXP_IO12 STMPE811 U29, I2C address 0x44 (7-bit) ------ ---- ---------------- -------------------------------------------- STPE11 PIN BOARD SIGNAL BOARD CONNECTION ------ ---- ---------------- -------------------------------------------- Y- EXP_IO1 X- EXP_IO2 Y+ EXP_IO3 X+ EXP_IO4 IN3 EXP_IO5 IN2 EXP_IO6 IN1 EXP_IO7 IN0 EXP_IO8 STM3240G-EVAL-specific Configuration Options ============================================ CONFIG_ARCH - Identifies the arch/ subdirectory. This should be set to: CONFIG_ARCH=arm CONFIG_ARCH_family - For use in C code: CONFIG_ARCH_ARM=y CONFIG_ARCH_architecture - For use in C code: CONFIG_ARCH_CORTEXM4=y CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory CONFIG_ARCH_CHIP=stm32 CONFIG_ARCH_CHIP_name - For use in C code to identify the exact chip: CONFIG_ARCH_CHIP_STM32F407IG=y CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock configuration features. CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n CONFIG_ARCH_BOARD - Identifies the configs subdirectory and hence, the board that supports the particular chip or SoC. CONFIG_ARCH_BOARD=stm3240g_eval (for the STM3240G-EVAL development board) CONFIG_ARCH_BOARD_name - For use in C code CONFIG_ARCH_BOARD_STM3240G_EVAL=y CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation of delay loops CONFIG_ENDIAN_BIG - define if big endian (default is little endian) CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case): CONFIG_DRAM_SIZE=0x00010000 (64Kb) CONFIG_DRAM_START - The start address of installed DRAM CONFIG_DRAM_START=0x20000000 CONFIG_STM32_CCMEXCLUDE - Exclude CCM SRAM from the HEAP In addition to internal SRAM, SRAM may also be available through the FSMC. In order to use FSMC SRAM, the following additional things need to be present in the NuttX configuration file: CONFIG_STM32_FSMC_SRAM - Indicates that SRAM is available via the FSMC (as opposed to an LCD or FLASH). CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space (hex) CONFIG_HEAP2_END - The size of the SRAM in the FSMC address space (decimal) CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization CONFIG_ARCH_IRQPRIO=y CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU) CONFIG_ARCH_FPU=y CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that have LEDs CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt stack. If defined, this symbol is the size of the interrupt stack in bytes. If not defined, the user task stacks will be used during interrupt handling. CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that cause a 100 second delay during boot-up. This 100 second delay serves no purpose other than it allows you to calibratre CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until the delay actually is 100 seconds. Individual subsystems can be enabled: AHB1 ---- CONFIG_STM32_CRC CONFIG_STM32_BKPSRAM CONFIG_STM32_CCMDATARAM CONFIG_STM32_DMA1 CONFIG_STM32_DMA2 CONFIG_STM32_ETHMAC CONFIG_STM32_OTGHS AHB2 ---- CONFIG_STM32_DCMI CONFIG_STM32_CRYP CONFIG_STM32_HASH CONFIG_STM32_RNG CONFIG_STM32_OTGFS AHB3 ---- CONFIG_STM32_FSMC APB1 ---- CONFIG_STM32_TIM2 CONFIG_STM32_TIM3 CONFIG_STM32_TIM4 CONFIG_STM32_TIM5 CONFIG_STM32_TIM6 CONFIG_STM32_TIM7 CONFIG_STM32_TIM12 CONFIG_STM32_TIM13 CONFIG_STM32_TIM14 CONFIG_STM32_WWDG CONFIG_STM32_IWDG CONFIG_STM32_SPI2 CONFIG_STM32_SPI3 CONFIG_STM32_USART2 CONFIG_STM32_USART3 CONFIG_STM32_UART4 CONFIG_STM32_UART5 CONFIG_STM32_I2C1 CONFIG_STM32_I2C2 CONFIG_STM32_I2C3 CONFIG_STM32_CAN1 CONFIG_STM32_CAN2 CONFIG_STM32_DAC1 CONFIG_STM32_DAC2 CONFIG_STM32_PWR -- Required for RTC APB2 ---- CONFIG_STM32_TIM1 CONFIG_STM32_TIM8 CONFIG_STM32_USART1 CONFIG_STM32_USART6 CONFIG_STM32_ADC1 CONFIG_STM32_ADC2 CONFIG_STM32_ADC3 CONFIG_STM32_SDIO CONFIG_STM32_SPI1 CONFIG_STM32_SYSCFG CONFIG_STM32_TIM9 CONFIG_STM32_TIM10 CONFIG_STM32_TIM11 Timer devices may be used for different purposes. One special purpose is to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn is defined (as above) then the following may also be defined to indicate that the timer is intended to be used for pulsed output modulation, ADC conversion, or DAC conversion. Note that ADC/DAC require two definition: Not only do you have to assign the timer (n) for used by the ADC or DAC, but then you also have to configure which ADC or DAC (m) it is assigned to. CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14 CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14 CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3 CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14 CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2 For each timer that is enabled for PWM usage, we need the following additional configuration settings: CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4} NOTE: The STM32 timers are each capable of generating different signals on each of the four channels with different duty cycles. That capability is not supported by this driver: Only one output channel per timer. JTAG Enable settings (by default JTAG-DP and SW-DP are disabled): CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) but without JNTRST. CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled STM3240xxx specific device driver settings CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART m (m=4,5) for the console and ttys0 (default is the USART1). CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received. This specific the size of the receive buffer CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before being sent. This specific the size of the transmit buffer CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8. CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity CONFIG_U[S]ARTn_2STOP - Two stop bits CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI support. Non-interrupt-driven, poll-waiting is recommended if the interrupt rate would be to high in the interrupt driven case. CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance. Cannot be used with CONFIG_STM32_SPI_INTERRUPT. CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO and CONFIG_STM32_DMA2. CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128 CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. Default: Medium CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default: 4-bit transfer mode. CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board CONFIG_STM32_MII - Support Ethernet MII interface CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface CONFIG_STM32_RMII - Support Ethernet RMII interface CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this may be defined to select full duplex mode. Default: half-duplex CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this may be defined to select 100 MBps speed. Default: 10 Mbps CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is defined. The PHY status register address may diff from PHY to PHY. This configuration sets the address of the PHY status register. CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is defined. This provides bit mask indicating 10 or 100MBps speed. CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is defined. This provides the value of the speed bit(s) indicating 100MBps speed. CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is defined. This provide bit mask indicating full or half duplex modes. CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is defined. This provides the value of the mode bits indicating full duplex mode. CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported but some hooks are indicated with this condition. STM3240G-EVAL CAN Configuration CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or CONFIG_STM32_CAN2 must also be defined) CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages. Default: 8 CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests. Default: 4 CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback mode for testing. The STM32 CAN driver does support loopback mode. CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined. CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined. CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7 CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an dump of all CAN registers. STM3240G-EVAL LCD Hardware Configuration The LCD driver supports the following LCDs on the STM324xG_EVAL board: AM-240320L8TNQW00H (LCD_ILI9320 or LCD_ILI9321) OR AM-240320D5TOQW01H (LCD_ILI9325) Configuration options. CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape" support. Default is this 320x240 "landscape" orientation For the STM3240G-EVAL board, the edge opposite from the row of buttons is used as the top of the display in this orientation. CONFIG_LCD_RLANDSCAPE - Define for 320x240 display "reverse landscape" support. Default is this 320x240 "landscape" orientation For the STM3240G-EVAL board, the edge next to the row of buttons is used as the top of the display in this orientation. CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait" orientation support. In this orientation, the STM3210E-EVAL's LCD ribbon cable is at the bottom of the display. Default is 320x240 "landscape" orientation. In this orientation, the top of the display is to the left of the buttons (if the board is held so that the buttons are at the botton of the board). CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse portrait" orientation support. In this orientation, the STM3210E-EVAL's LCD ribbon cable is at the top of the display. Default is 320x240 "landscape" orientation. In this orientation, the top of the display is to the right of the buttons (if the board is held so that the buttons are at the botton of the board). CONFIG_LCD_RDSHIFT - When reading 16-bit gram data, there appears to be a shift in the returned data. This value fixes the offset. Default 5. The LCD driver dynamically selects the LCD based on the reported LCD ID value. However, code size can be reduced by suppressing support for individual LCDs using: CONFIG_STM32_ILI9320_DISABLE (includes ILI9321) CONFIG_STM32_ILI9325_DISABLE STM32 USB OTG FS Host Driver Support Pre-requisites CONFIG_USBHOST - Enable USB host support CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block CONFIG_STM32_SYSCFG - Needed CONFIG_SCHED_WORKQUEUE - Worker thread support is required Options: CONFIG_STM32_OTGFS_RXFIFO_SIZE - Size of the RX FIFO in 32-bit words. Default 128 (512 bytes) CONFIG_STM32_OTGFS_NPTXFIFO_SIZE - Size of the non-periodic Tx FIFO in 32-bit words. Default 96 (384 bytes) CONFIG_STM32_OTGFS_PTXFIFO_SIZE - Size of the periodic Tx FIFO in 32-bit words. Default 96 (384 bytes) CONFIG_STM32_OTGFS_DESCSIZE - Maximum size of a descriptor. Default: 128 CONFIG_STM32_OTGFS_SOFINTR - Enable SOF interrupts. Why would you ever want to do that? CONFIG_STM32_USBHOST_REGDEBUG - Enable very low-level register access debug. Depends on CONFIG_DEBUG. CONFIG_STM32_USBHOST_PKTDUMP - Dump all incoming and outgoing USB packets. Depends on CONFIG_DEBUG. Configurations ============== Each STM3240G-EVAL configuration is maintained in a sub-directory and can be selected as follow: cd tools ./configure.sh stm3240g-eval/ cd - . ./setenv.sh Where is one of the following: dhcpd: ----- This builds the DCHP server using the apps/examples/dhcpd application (for execution from FLASH.) See apps/examples/README.txt for information about the dhcpd example. The server address is 10.0.0.1 and it serves IP addresses in the range 10.0.0.2 through 10.0.0.17 (all of which, of course, are configurable). CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows discover: -------- This configuration exercises netutils/discover utility using apps/exmaples/discover. This example initializes and starts the UDP discover daemon. This daemon is useful for discovering devices in local networks, especially with DHCP configured devices. It listens for UDP broadcasts which also can include a device class so that groups of devices can be discovered. It is also possible to address all classes with a kind of broadcast discover. Configuration settings that you may need to change for your environment: CONFIG_STM32_CODESOURCERYL=y - CodeSourcery for Linux CONFIG_EXAMPLES_DISCOVER_DHCPC=y - DHCP Client CONFIG_EXAMPLES_DISCOVER_IPADDR - (not defined) CONFIG_EXAMPLES_DISCOVER_DRIPADDR - Router IP address NOTE: This configuration uses to the kconfig-mconf configuration tool to control the configuration. See the section entitled "NuttX Configuration Tool" in the top-level README.txt file. nettest: ------- This configuration directory may be used to verify networking performance using the STM32's Ethernet controller. It uses apps/examples/nettest to excercise the TCP/IP network. CONFIG_EXAMPLES_NETTEST_SERVER=n : Target is configured as the client CONFIG_EXAMPLES_NETTEST_PERFORMANCE=y : Only network performance is verified. CONFIG_EXAMPLES_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) : Target side is IP: 10.0.0.2 CONFIG_EXAMPLES_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host side is IP: 10.0.0.1 CONFIG_EXAMPLES_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) : Server address used by which ever is client. nsh: --- Configures the NuttShell (nsh) located at apps/examples/nsh. The Configuration enables both the serial and telnet NSH interfaces. CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows CONFIG_NSH_DHCPC=n : DHCP is disabled CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2) : Target IP address 10.0.0.2 CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host IP address 10.0.0.1 NOTES: 1. This example assumes that a network is connected. During its initialization, it will try to negotiate the link speed. If you have no network connected when you reset the board, there will be a long delay (maybe 30 seconds?) before anything happens. That is the timeout before the networking finally gives up and decides that no network is available. 2. This example supports the ADC test (apps/examples/adc) but this must be manually enabled by selecting: CONFIG_ADC=y : Enable the generic ADC infrastructure CONFIG_STM32_ADC3=y : Enable ADC3 CONFIG_STM32_TIM1=y : Enable Timer 1 CONFIG_STM32_TIM1_ADC=y : Indicate that timer 1 will be used to trigger an ADC CONFIG_STM32_TIM1_ADC3=y : Assign timer 1 to drive ADC3 sampling CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 : Select a sampling frequency See also apps/examples/README.txt General debug for analog devices (ADC/DAC): CONFIG_DEBUG_ANALOG 3. This example supports the PWM test (apps/examples/pwm) but this must be manually enabled by selecting eeither CONFIG_PWM=y : Enable the generic PWM infrastructure CONFIG_PWM_PULSECOUNT=n : Disable to support for TIM1/8 pulse counts CONFIG_STM32_TIM4=y : Enable TIM4 CONFIG_STM32_TIM4_PWM=y : Use TIM4 to generate PWM output CONFIG_STM32_TIM4_CHANNEL=2 : Select output on TIM4, channel 2 If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 32. Ground is available on CN3, pin1. Or.. CONFIG_PWM=y : Enable the generic PWM infrastructure CONFIG_PWM_PULSECOUNT=y : Enable to support for TIM1/8 pulse counts CONFIG_STM32_TIM8=y : Enable TIM8 CONFIG_STM32_TIM8_PWM=y : Use TIM8 to generate PWM output CONFIG_STM32_TIM8_CHANNEL=4 : Select output on TIM8, channel 4 If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 17 Ground is available on CN23 pin1. See also include/board.h and apps/examples/README.txt Special PWM-only debug options: CONFIG_DEBUG_PWM 4. This example supports the CAN loopback test (apps/examples/can) but this must be manually enabled by selecting: CONFIG_CAN=y : Enable the generic CAN infrastructure CONFIG_CAN_EXID=y or n : Enable to support extended ID frames CONFIG_STM32_CAN1=y : Enable CAN1 CONFIG_CAN_LOOPBACK=y : Enable CAN loopback mode See also apps/examples/README.txt Special CAN-only debug options: CONFIG_DEBUG_CAN CONFIG_CAN_REGDEBUG 5. This example can support an FTP client. In order to build in FTP client support simply uncomment the following lines in the appconfig file (before configuring) or in the apps/.config file (after configuring): #CONFIGURED_APPS += netutils/ftpc #CONFIGURED_APPS += examples/ftpc 6. This example can support an FTP server. In order to build in FTP server support simply uncomment the following lines in the appconfig file (before configuring) or in the apps/.config file (after configuring): #CONFIGURED_APPS += netutils/ftpd #CONFIGURED_APPS += examples/ftpd And enable poll() support in the NuttX configuration file: CONFIG_DISABLE_POLL=n 7. This example supports the watchdog timer test (apps/examples/watchdog) but this must be manually enabled by selecting: CONFIG_WATCHDOG=y : Enables watchdog timer driver support CONFIG_STM32_WWDG=y : Enables the WWDG timer facility, OR CONFIG_STM32_IWDG=y : Enables the IWDG timer facility (but not both) The WWDG watchdog is driven off the (fast) 42MHz PCLK1 and, as result, has a maximum timeout value of 49 milliseconds. For WWDG watchdog, you should also add the fillowing to the configuration file: CONFIG_EXAMPLES_WATCHDOG_PINGDELAY=20 CONFIG_EXAMPLES_WATCHDOG_TIMEOUT=49 The IWDG timer has a range of about 35 seconds and should not be an issue. 7. Adding LCD and graphics support: appconfig (apps/.config): Enable the application configurations that you want to use. Asexamples: CONFIGURED_APPS += examples/nx : Pick one or more CONFIGURED_APPS += examples/nxhello : CONFIGURED_APPS += examples/nximage : CONFIGURED_APPS += examples/nxlines : defconfig (nuttx/.config): CONFIG_STM32_FSMC=y : FSMC support is required for the LCD CONFIG_NX=y : Enable graphics suppport CONFIG_MM_REGIONS=3 : When FSMC is enabled, so is the on-board SRAM memory region 8. USB OTG FS Device or Host Support CONFIG_USBDEV - Enable USB device support, OR CONFIG_USBHOST - Enable USB host support CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block CONFIG_STM32_SYSCFG - Needed CONFIG_SCHED_WORKQUEUE - Worker thread support is required 9. USB OTG FS Host Support. The following changes will enable support for a USB host on the STM32F4Discovery, including support for a mass storage class driver: CONFIG_USBDEV=n - Make sure tht USB device support is disabled CONFIG_USBHOST=y - Enable USB host support CONFIG_STM32_OTGFS=y - Enable the STM32 USB OTG FS block CONFIG_STM32_SYSCFG=y - Needed for all USB OTF FS support CONFIG_SCHED_WORKQUEUE=y - Worker thread support is required for the mass storage class driver. CONFIG_NSH_ARCHINIT=y - Architecture specific USB initialization is needed for NSH CONFIG_FS_FAT=y - Needed by the USB host mass storage class. With those changes, you can use NSH with a FLASH pen driver as shown belong. Here NSH is started with nothing in the USB host slot: NuttShell (NSH) NuttX-x.yy nsh> ls /dev /dev: console null ttyS0 After inserting the FLASH drive, the /dev/sda appears and can be mounted like this: nsh> ls /dev /dev: console null sda ttyS0 nsh> mount -t vfat /dev/sda /mnt/stuff nsh> ls /mnt/stuff /mnt/stuff: -rw-rw-rw- 16236 filea.c And files on the FLASH can be manipulated to standard interfaces: nsh> echo "This is a test" >/mnt/stuff/atest.txt nsh> ls /mnt/stuff /mnt/stuff: -rw-rw-rw- 16236 filea.c -rw-rw-rw- 16 atest.txt nsh> cat /mnt/stuff/atest.txt This is a test nsh> cp /mnt/stuff/filea.c fileb.c nsh> ls /mnt/stuff /mnt/stuff: -rw-rw-rw- 16236 filea.c -rw-rw-rw- 16 atest.txt -rw-rw-rw- 16236 fileb.c To prevent data loss, don't forget to un-mount the FLASH drive before removing it: nsh> umount /mnt/stuff 11. By default, this configuration supports /dev/random using the STM32's RNG hardware. This can be disabled as follows: -CONFIG_STM32_RNG=y +CONFIG_STM32_RNG=n -CONFIG_DEV_RANDOM=y +CONFIG_DEV_RANDOM=n 12. This configuration requires that jumper JP22 be set to enable RS-232 operation. nsh2: ----- This is an alternative NSH configuration. One limitation of the STM3240G-EVAL board is that you cannot have both a UART-based NSH console and SDIO support. The nsh2 differs from the nsh configuration in the following ways: -CONFIG_STM32_USART3=y : USART3 is disabled +CONFIG_STM32_USART3=n -CONFIG_STM32_SDIO=n : SDIO is enabled +CONFIG_STM32_SDIO=y Logically, these are the only differences: This configuration has SDIO (and the SD card) enabled and the serial console disabled. There is ONLY a Telnet console!. There are some special settings to make life with only a Telnet CONFIG_SYSLOG=y - Enables the System Logging feature. CONFIG_RAMLOG=y - Enable the RAM-based logging feature. CONFIG_RAMLOG_CONSOLE=y - Use the RAM logger as the default console. This means that any console output from non-Telnet threads will go into the circular buffer in RAM. CONFIG_RAMLOG_SYSLOG - This enables the RAM-based logger as the system logger. This means that (1) in addition to the console output from other tasks, ALL of the debug output will also to to the circular buffer in RAM, and (2) NSH will now support a command called 'dmesg' that can be used to dump the RAM log. There are a few other configuration differences as necessary to support this different device configuration. Just the do the 'diff' if you are curious. NOTES: 1. See the notes for the nsh configuration. Most also apply to the nsh2 configuration. Like the nsh configuration, this configuration can be modified to support a variety of additional tests. 2. RS-232 is disabled, but Telnet is still available for use as a console. Since RS-232 and SDIO use the same pins (one controlled by JP22), RS232 and SDIO cannot be used concurrently. 3. This configuration requires that jumper JP22 be set to enable SDIO operation. To enable MicroSD Card, which shares same I/Os with RS-232, JP22 is not fitted. 4. In order to use SDIO without overruns, DMA must be used. The STM32 F4 has 192Kb of SRAM in two banks: 112Kb of "system" SRAM located at 0x2000:0000 and 64Kb of "CCM" SRAM located at 0x1000:0000. It appears that you cannot perform DMA from CCM SRAM. The work around that I have now is simply to omit the 64Kb of CCM SRAM from the heap so that all memory is allocated from System SRAM. This is done by setting: CONFIG_MM_REGIONS=1 Then DMA works fine. The downside is, of course, is that we lose 64Kb of precious SRAM. 5. Another SDIO/DMA issue. This one is probably a software bug. This is the bug as stated in the TODO list: "If you use a large I/O buffer to access the file system, then the MMCSD driver will perform multiple block SD transfers. With DMA ON, this seems to result in CRC errors detected by the hardware during the transfer. Workaround: CONFIG_MMCSD_MULTIBLOCK_DISABLE=y" For this reason, CONFIG_MMCSD_MULTIBLOCK_DISABLE=y appears in the defconfig file. 6. Another DMA-related concern. I see this statement in the reference manual: "The burst configuration has to be selected in order to respect the AHB protocol, where bursts must not cross the 1 KB address boundary because the minimum address space that can be allocated to a single slave is 1 KB. This means that the 1 KB address boundary should not be crossed by a burst block transfer, otherwise an AHB error would be generated, that is not reported by the DMA registers." There is nothing in the DMA driver to prevent this now. nxconsole: ---------- This is yet another NSH configuration. This NSH configuration differs from the others, however, in that it uses the NxConsole driver to host the NSH shell. Some of the differences in this configuration and the normal nsh configuration include these settings in the defconfig file: These select NX Multi-User mode: CONFG_NX_MULTIUSER=y CONFIG_DISABLE_MQUEUE=n The following definition in the defconfig file to enables the NxConsole driver: CONFIG_NXCONSOLE=y The appconfig file selects examples/nxconsole instead of examples/nsh: CONFIGURED_APPS += examples/nxconsole Other configuration settings: CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows CONFIG_LCD_LANDSCAPE=y : 320x240 landscape nxwm ---- This is a special configuration setup for the NxWM window manager UnitTest. The NxWM window manager can be found here: nuttx-code/NxWidgets/nxwm The NxWM unit test can be found at: nuttx-code/NxWidgets/UnitTests/nxwm Documentation for installing the NxWM unit test can be found here: nuttx-code/NxWidgets/UnitTests/README.txt Here is the quick summary of the build steps (Assuming that all of the required packages are available in a directory ~/nuttx-code): 1. Intall the nxwm configuration $ cd ~/nuttx-code/nuttx/tools $ ./configure.sh stm3240g-eval/nxwm 2. Make the build context (only) $ cd .. $ . ./setenv.sh $ make context ... 3. Install the nxwm unit test $ cd ~/nuttx-code/NxWidgets $ tools/install.sh ~/nuttx-code/apps nxwm Creating symbolic link - To ~/nuttx-code/NxWidgets/UnitTests/nxwm - At ~/nuttx-code/apps/external 4. Build the NxWidgets library $ cd ~/nuttx-code/NxWidgets/libnxwidgets $ make TOPDIR=~/nuttx-code/nuttx ... 5. Build the NxWM library $ cd ~/nuttx-code/NxWidgets/nxwm $ make TOPDIR=~/nuttx-code/nuttx ... 6. Built NuttX with the installed unit test as the application $ cd ~/nuttx-code/nuttx $ make ostest: ------ This configuration directory, performs a simple OS test using examples/ostest. By default, this project assumes that you are using the DFU bootloader. CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows If you use the Atollic toolchain, then the FPU test can be enabled in the examples/ostest by adding the following your NuttX configuration file: -CONFIG_ARCH_FPU=n : Enable FPU support +CONFIG_ARCH_FPU=y -CONFIG_STM32_CODESOURCERYW=y : Disable the CodeSourcery toolchain +CONFIG_STM32_CODESOURCERYW=n -CONFIG_STM32_ATOLLIC_LITE=n : Enable *one* the Atollic toolchains CONFIG_STM32_ATOLLIC_PRO=n -CONFIG_STM32_ATOLLIC_LITE=y : The "Lite" version, OR CONFIG_STM32_ATOLLIC_PRO=n : The "Pro" version (only one) -CONFIG_INTELHEX_BINARY=y : Suppress generation FLASH download formats +CONFIG_INTELHEX_BINARY=n : (Only necessary with the "Lite" version) -CONFIG_HAVE_CXX=y : Suppress generation of C++ code +CONFIG_HAVE_CXX=n : (Only necessary with the "Lite" version) -CONFIG_SCHED_WAITPID=y : Enable the waitpid() API needed by the FPU test +CONFIG_SCHED_WAITPID=n The FPU test also needs to know the size of the FPU registers save area in bytes (see arch/arm/include/armv7-m/irq_lazyfpu.h): +CONFIG_EXAMPLES_OSTEST_FPUSIZE=(4*33) telnetd: -------- A simple test of the Telnet daemon(see apps/netutils/README.txt, apps/examples/README.txt, and apps/examples/telnetd). This is the same daemon that is used in the nsh configuration so if you use NSH, then you don't care about this. This test is good for testing the Telnet daemon only because it works in a simpler environment than does the nsh configuration. xmlrpc ------ An example configuration for the Embeddable Lightweight XML-RPC Server at apps/examples/xmlrpc. See http://www.drdobbs.com/web-development/\ an-embeddable-lightweight-xml-rpc-server/184405364 for more info. Contributed by Max Holtzberg.