/**************************************************************************** * configs/sure-pic32mx/include/board.h * include/arch/board/board.h * * Copyright (C) 2011-2012 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #ifndef __CONFIGS_SURE_PIC32MX_INCLUDE_BOARD_H #define __CONFIGS_SURE_PIC32MX_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include /**************************************************************************** * Pre-Processor Definitions ****************************************************************************/ /* Configuration ************************************************************/ /* Clocking *****************************************************************/ /* Crystal frequencies */ #define BOARD_POSC_FREQ 20000000 /* Primary OSC XTAL frequency (20MHz) */ #define BOARD_SOSC_FREQ 32768 /* Secondary OSC XTAL frequency (32.768KHz) */ /* Oscillator modes */ #define BOARD_FNOSC_POSCPLL 1 /* Use primary oscillator w/PLL */ #define BOARD_POSC_HSMODE 1 /* High-speed crystal (HS) mode */ /* PLL configuration and resulting CPU clock. * CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV */ #define BOARD_PLL_INPUT BOARD_POSC_FREQ #define BOARD_PLL_IDIV 5 /* PLL input divider */ #define BOARD_PLL_MULT 15 /* PLL multiplier */ #define BOARD_PLL_ODIV 1 /* PLL output divider */ #define BOARD_CPU_CLOCK 60000000 /* CPU clock (60MHz = (20MHz / 5) * 15 / 1) */ /* USB PLL configuration. * USB_CLOCK = ((POSC_XTAL / IDIV) * 24) / 2 */ #define BOARD_UPLL_IDIV 5 /* USB PLL divider */ #define BOARD_USB_CLOCK 48000000 /* USB clock ((20MHz / 5) * 24) / 2 */ /* Peripheral clock is *not* divided down from CPU clock. * PBCLOCK = CPU_CLOCK / PBDIV */ #define BOARD_PBDIV 1 /* Peripheral clock divisor (PBDIV) */ #define BOARD_PBCLOCK 60000000 /* Peripheral clock (PBCLK = 60MHz/1) */ /* Watchdog pre-scaler (re-visit) */ #define BOARD_WD_ENABLE 0 /* Watchdog is disabled */ #define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */ /* Timer 1 is a type A timer and is used as system clock. It can be clocked * with either the SOSC or the PBCLOCK. We will use the PBCLOCK because it * is much more accurate. */ #undef BOARD_TIMER1_SOSC /* LED definitions **********************************************************/ /* The Sure DB_DP11215 PIC32 Storage Demo Board board has five LEDs. One * (D4, lablel "Power") is not controllable by software. Four are * controllable by software: * * D7 "USB" Yellow RD7 Low illuminates * D8 "SD" Yellow RD6 Low illuminates * D9 "Flash" Yellow RF0 Low illuminates * D10 "Error" Red RF1 Low illuminates */ /* ON OFF */ /* USB SD FLASH ERROR USB SD FLASH ERROR */ #define LED_STARTED 0 /* OFF OFF OFF OFF --- --- --- --- */ #define LED_HEAPALLOCATE 1 /* ON OFF N/C N/C --- --- --- --- */ #define LED_IRQSENABLED 2 /* OFF ON N/C N/C --- --- --- --- */ #define LED_STACKCREATED 3 /* ON ON N/C N/C --- --- --- --- */ #define LED_INIRQ 4 /* N/C N/C ON N/C N/C N/C OFF N/C */ #define LED_SIGNAL 4 /* N/C N/C ON N/C N/C N/C OFF N/C */ #define LED_ASSERTION 4 /* N/C N/C ON N/C N/C N/C OFF N/C */ #define LED_PANIC 5 /* N/C N/C N/C ON N/C N/C N/C OFF */ #define LED_NVALUES 6 /* The Sure DB-DP11212 PIC32 General Purpose Demo Board does not have any user * controllable LEDs, but does does have a segment LED display. That display is * however, obscured by the larger segment display attached to the board and, so, * is not supported. */ /* For distinguishing individual LEDs */ #define LED_USB 0 #define LED_SD 1 #define LED_FLASH 2 #define LED_ERROR 3 /* Button Definitions *******************************************************/ /* The Sure PIC32MX board has three buttons. * * SW1 (SW_UP, left arrow) RB3 Pulled high, Grounded/low when depressed * SW2 (SW_DOWN, down/right arrow) RB2 Pulled high, Grounded/low when depressed * SW3 (SW_OK, right arrow) RB4 Pulled high, Grounded/low when depressed */ #define BUTTON_SW1 0 #define BUTTON_SW2 1 #define BUTTON_SW3 2 #define NUM_BUTTONS 3 #define BUTTON_SW1_BIT (1 << BUTTON_SW1) #define BUTTON_SW2_BIT (1 << BUTTON_SW2) #define BUTTON_SW3_BIT (1 << BUTTON_SW3) /**************************************************************************** * Public Types ****************************************************************************/ #ifndef __ASSEMBLY__ /**************************************************************************** * Inline Functions ****************************************************************************/ /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #ifdef __cplusplus #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Button support. * * Description: * up_buttoninit() must be called to initialize button resources. After * that, up_buttons() may be called to collect the current state of all * buttons or up_irqbutton() may be called to register button interrupt * handlers. * * After up_buttoninit() has been called, up_buttons() may be called to * collect the state of all buttons. up_buttons() returns an 8-bit bit set * with each bit associated with a button. See the BUTTON_*_BIT * definitions in board.h for the meaning of each bit. * * up_irqbutton() may be called to register an interrupt handler that will * be called when a button is depressed or released. The ID value is a * button enumeration value that uniquely identifies a button resource. * See the BUTTON_* definitions in board.h for the meaning of enumeration * value. The previous interrupt handler address is returned (so that it * may restored, if so desired). * * When an interrupt occurs, it is due to a change on the GPIO input pin * associated with the button. In that case, all attached change * notification handlers will be called. Each handler must maintain state * and determine if the unlying GPIO button input value changed. * ****************************************************************************/ #ifdef CONFIG_ARCH_BUTTONS EXTERN void up_buttoninit(void); EXTERN uint8_t up_buttons(void); #ifdef CONFIG_ARCH_IRQBUTTONS EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler); #endif #endif #undef EXTERN #ifdef __cplusplus } #endif #endif /* __ASSEMBLY__ */ #endif /* __CONFIGS_SURE_PIC32MX_INCLUDE_BOARD_H */