|
|
/************************************************************************************
* configs/dk-tm4c129x/include/board.h
*
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_DK_TM4C129X_INCLUDE_BOARD_H
#define __CONFIGS_DK_TM4C129X_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#ifndef __ASSEMBLY__
# include <stdbool.h>
#endif
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* Crystals on-board the DK-TM4C129X include:
*
* 1. 25.0MHz (Y2) is connected to OSC0/1 pins and is used as the run mode input to
* the PLL.
* 2. 32.768kHz (Y3) connected to XOSC0/1 and clocks the hibernation module.
*/
#define SYSCON_RCC_XTAL SYSCON_RCC_XTAL16000KHZ /* On-board crystal is 25 MHz */
#define XTAL_FREQUENCY 25000000
/* The PLL generates Fvco according to the following formulae. The input clock to
* the PLL may be either the external crystal (Fxtal) or PIOSC (Fpiosc). This
* logic supports only the external crystal as the PLL source clock.
*
* Fin = Fxtal / (Q + 1 )(N + 1) -OR- Fpiosc / (Q + 1)(N + 1)
* Mdiv = Mint + (MFrac / 1024)
* Fvco = Fin * Mdiv
*
* Where the register fields Q and N actually hold (Q-1) and (N-1). The following
* setup then generates Fvco = 480MHz:
*
* Fin = 25 MHz / 1 / 5 = 5 MHz
* Mdiv = 96
* Fvco = 480
*/
#define BOARD_PLL_MINT 96 /* Integer part of PLL M value */
#define BOARD_PLL_MFRAC 0 /* Fractional part of PLL M value */
#define BOARD_PLL_N 5 /* PLL N value */
#define BOARD_PLL_Q 1 /* PLL Q value */
#define BOARD_FVCO_FREQUENCY 480000000 /* Resulting Fvco */
/* When the PLL is active, the system clock frequency (SysClk) is calculated using
* the following equation:
*
* SysClk = Fvco/ (sysdiv + 1)
*
* The following setup generates Sysclk = 120MHz:
*/
#define BOARD_PLL_SYSDIV 4 /* Sysclk = Fvco / 4 = 120MHz */
#define SYSCLK_FREQUENCY 120000000 /* Resulting SysClk frequency */
/* LED definitions ******************************************************************/
/* The DK-TM4C129X has a single RGB LED. There is only one visible LED which
* will vary in color. But, from the standpoint of the firmware, this appears as
* three LEDs:
*
* --- ------------ -----------------
* Pin Pin Function Jumper
* --- ------------ -----------------
* PN5 Red LED J36 pins 1 and 2
* PQ4 Blue LED J36 pins 3 and 4
* PQ7 Green LED J36 pins 5 and 6
* --- ------------ -----------------
*/
/* LED index values for use with tm4c_setled() */
#define BOARD_LED_R 0
#define BOARD_LED_G 1
#define BOARD_LED_B 2
#define BOARD_NLEDS 3
/* LED bits for use with tm4c_setleds() */
#define BOARD_LED_R_BIT (1 << BOARD_LED_R)
#define BOARD_LED_G_BIT (1 << BOARD_LED_G)
#define BOARD_LED_B_BIT (1 << BOARD_LED_B)
/* If CONFIG_ARCH_LEDS is defined, then automated support for the DK-TM4C129X LED
* will be included in the build:
*/
/* RED GREEN BLUE */
#define LED_STARTED 0 /* OFF OFF ON */
#define LED_HEAPALLOCATE 1 /* NC NC NC */
#define LED_IRQSENABLED 1 /* NC NC NC */
#define LED_STACKCREATED 2 /* OFF ON OFF */
#define LED_INIRQ 1 /* NC NC NC */
#define LED_SIGNAL 1 /* NC NC NC */
#define LED_ASSERTION 1 /* NC NC NC */
#define LED_PANIC 3 /* ON OFF OFF (flashing 2Hz) */
/* Button definitions ***************************************************************/
/* There are three push buttons on the board.
*
* --- ------------ -----------------
* Pin Pin Function Jumper
* --- ------------ -----------------
* PP1 Select SW4 J37 pins 1 and 2
* PN3 Up SW2 J37 pins 3 and 4
* PE5 Down SW3 J37 pins 5 and 6
* --- ------------ -----------------
*/
#define BUTTON_SW2 0
#define BUTTON_SW3 1
#define BUTTON_SW4 2
#define NUM_BUTTONS 3
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
#define BUTTON_SW4_BIT (1 << BUTTON_SW4)
/* Pin Multiplexing Disambiguation **************************************************/
#define GPIO_UART1_CTS GPIO_UART1_CTS_1
#define GPIO_UART1_RTS GPIO_UART1_RTS_1
#define GPIO_UART1_RX GPIO_UART1_RX_1
#define GPIO_UART1_TX GPIO_UART1_TX_1
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Name: tiva_boardinitialize
*
* Description:
* All Tiva architectures must provide the following entry point. This entry
* point is called early in the initialization -- after all memory has been
* configured and mapped but before any devices have been initialized.
*
************************************************************************************/
void tiva_boardinitialize(void);
/************************************************************************************
* Name: tm4c_ledinit, tm4c_setled, and tm4c_setleds
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LED. If
* CONFIG_ARCH_LEDS is not defined, then the following interfaces are available to
* control the LEDs from user applications.
*
************************************************************************************/
#ifndef CONFIG_ARCH_LEDS
void tm4c_ledinit(void);
void tm4c_setled(int led, bool ledon);
void tm4c_setleds(uint8_t ledset);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_DK_TM4C129X_INCLUDE_BOARD_H */
|
