diff options
Diffstat (limited to 'src/drivers/boards/px4fmu-v1/board_config.h')
| -rw-r--r-- | src/drivers/boards/px4fmu-v1/board_config.h | 212 |
1 files changed, 212 insertions, 0 deletions
diff --git a/src/drivers/boards/px4fmu-v1/board_config.h b/src/drivers/boards/px4fmu-v1/board_config.h new file mode 100644 index 000000000..02c26b5c0 --- /dev/null +++ b/src/drivers/boards/px4fmu-v1/board_config.h @@ -0,0 +1,212 @@ +/**************************************************************************** + * + * Copyright (c) 2012-2014 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file board_config.h + * + * PX4FMUv1 internal definitions + */ + +#pragma once + +/**************************************************************************************************** + * Included Files + ****************************************************************************************************/ + +#include <nuttx/config.h> +#include <nuttx/compiler.h> +#include <stdint.h> + +__BEGIN_DECLS + +/* these headers are not C++ safe */ +#include <stm32.h> +#include <arch/board/board.h> + +/**************************************************************************************************** + * Definitions + ****************************************************************************************************/ +/* Configuration ************************************************************************************/ + +/* PX4IO connection configuration */ +#define PX4IO_SERIAL_DEVICE "/dev/ttyS2" +#define UDID_START 0x1FFF7A10 + +//#ifdef CONFIG_STM32_SPI2 +//# error "SPI2 is not supported on this board" +//#endif + +#if defined(CONFIG_STM32_CAN1) +# warning "CAN1 is not supported on this board" +#endif + +/* PX4FMU GPIOs ***********************************************************************************/ +/* LEDs */ + +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN15) +#define GPIO_LED2 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN14) + +/* External interrupts */ +#define GPIO_EXTI_COMPASS (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN1) + +/* SPI chip selects */ +#define GPIO_SPI_CS_GYRO (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN14) +#define GPIO_SPI_CS_ACCEL (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN15) +#define GPIO_SPI_CS_MPU (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN0) +#define GPIO_SPI_CS_SDCARD (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4) + +/* + * Use these in place of the spi_dev_e enumeration to + * select a specific SPI device on SPI1 + */ +#define PX4_SPIDEV_GYRO 1 +#define PX4_SPIDEV_ACCEL 2 +#define PX4_SPIDEV_MPU 3 + +/* + * Optional devices on IO's external port + */ +#define PX4_SPIDEV_ACCEL_MAG 2 + +/* + * I2C busses + */ +#define PX4_I2C_BUS_ESC 1 +#define PX4_I2C_BUS_ONBOARD 2 +#define PX4_I2C_BUS_EXPANSION 3 +#define PX4_I2C_BUS_LED 3 + +/* + * Devices on the onboard bus. + * + * Note that these are unshifted addresses. + */ +#define PX4_I2C_OBDEV_HMC5883 0x1e +#define PX4_I2C_OBDEV_MS5611 0x76 +#define PX4_I2C_OBDEV_EEPROM NOTDEFINED +#define PX4_I2C_OBDEV_LED 0x55 + +#define PX4_I2C_OBDEV_PX4IO_BL 0x18 +#define PX4_I2C_OBDEV_PX4IO 0x1a + +/* User GPIOs + * + * GPIO0-1 are the buffered high-power GPIOs. + * GPIO2-5 are the USART2 pins. + * GPIO6-7 are the CAN2 pins. + */ +#define GPIO_GPIO0_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN4) +#define GPIO_GPIO1_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN5) +#define GPIO_GPIO2_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN0) +#define GPIO_GPIO3_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN1) +#define GPIO_GPIO4_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN2) +#define GPIO_GPIO5_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN3) +#define GPIO_GPIO6_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN13) +#define GPIO_GPIO7_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN2) +#define GPIO_GPIO0_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN4) +#define GPIO_GPIO1_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN5) +#define GPIO_GPIO2_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN0) +#define GPIO_GPIO3_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN1) +#define GPIO_GPIO4_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN2) +#define GPIO_GPIO5_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN3) +#define GPIO_GPIO6_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN13) +#define GPIO_GPIO7_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN12) +#define GPIO_GPIO_DIR (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13) + +/* + * Tone alarm output + */ +#define TONE_ALARM_TIMER 3 /* timer 3 */ +#define TONE_ALARM_CHANNEL 3 /* channel 3 */ +#define GPIO_TONE_ALARM_IDLE (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN8) +#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF2|GPIO_SPEED_2MHz|GPIO_FLOAT|GPIO_PUSHPULL|GPIO_PORTC|GPIO_PIN8) + +/* + * PWM + * + * Four PWM outputs can be configured on pins otherwise shared with + * USART2; two can take the flow control pins if they are not being used. + * + * Pins: + * + * CTS - PA0 - TIM2CH1 + * RTS - PA1 - TIM2CH2 + * TX - PA2 - TIM2CH3 + * RX - PA3 - TIM2CH4 + * + */ +#define GPIO_TIM2_CH1OUT GPIO_TIM2_CH1OUT_1 +#define GPIO_TIM2_CH2OUT GPIO_TIM2_CH2OUT_1 +#define GPIO_TIM2_CH3OUT GPIO_TIM2_CH3OUT_1 +#define GPIO_TIM2_CH4OUT GPIO_TIM2_CH4OUT_1 + +/* USB OTG FS + * + * PA9 OTG_FS_VBUS VBUS sensing (also connected to the green LED) + */ +#define GPIO_OTGFS_VBUS (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|GPIO_OPENDRAIN|GPIO_PORTA|GPIO_PIN9) + +/* High-resolution timer + */ +#define HRT_TIMER 1 /* use timer1 for the HRT */ +#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */ +#define HRT_PPM_CHANNEL 3 /* use capture/compare channel 3 */ +#define GPIO_PPM_IN (GPIO_ALT|GPIO_AF1|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN10) + +/**************************************************************************************************** + * Public Types + ****************************************************************************************************/ + +/**************************************************************************************************** + * Public data + ****************************************************************************************************/ + +#ifndef __ASSEMBLY__ + +/**************************************************************************************************** + * Public Functions + ****************************************************************************************************/ + +/**************************************************************************************************** + * Name: stm32_spiinitialize + * + * Description: + * Called to configure SPI chip select GPIO pins for the PX4FMU board. + * + ****************************************************************************************************/ + +extern void stm32_spiinitialize(void); + +#endif /* __ASSEMBLY__ */ + +__END_DECLS |