Add support for the STM32F4-Discovery (from Mike Smith)

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4294 42af7a65-404d-4744-a932-0658087f49c3

22 files changed, 5495 insertions, 5 deletions

diff --git a/nuttx/ChangeLog b/nuttx/ChangeLog
index ec26460ff..a85870c82 100644
--- a/nuttx/ChangeLog
+++ b/nuttx/ChangeLog
@@ -2357,3 +2357,6 @@
 	  support for pulse count in order to better support stepper motors.
 	* arch/arm/src/stm32/stm32_dumpgpio.c: Checking wrong register to see if
 	  GPIO is enabled.  Also not adding the GPIO base address to several offsets.
+	* configs/stm32f4discovery:  Port to the STMicro STM32F4Discovery board
+	  (Contributed by Mike Smith).
+
diff --git a/nuttx/Documentation/NuttX.html b/nuttx/Documentation/NuttX.html
index 6957f1efb..f9a187cfe 100644
--- a/nuttx/Documentation/NuttX.html
+++ b/nuttx/Documentation/NuttX.html
@@ -8,7 +8,7 @@
   <tr align="center" bgcolor="#e4e4e4">
     <td>
       <h1><big><font color="#3c34ec"><i>NuttX RTOS</i></font></big></h1>
-      <p>Last Updated: January 4, 2012</p>
+      <p>Last Updated: January 11, 2012</p>
     </td>
   </tr>
 </table>
@@ -1722,15 +1722,13 @@
   <td>
     <p>
       <b>STMicro STM32F4-Discovery</b>.
-      This port is just beginning and is not yet available.
-      It will used the STMicor STM32F4-Discovery board featuring the STM32F407VGT6 MCU.
+      This port uses the STMicro STM32F4-Discovery board featuring the STM32F407VGT6 MCU.
       Refer to the <a href="http://www.st.com/internet/evalboard/product/252419.jsp">STMicro web site</a> for further information about this board.
     </p>
     <ul>
       <p>
         <b>STATUS:</b>
-        This is really a vapor ware, pre-announcement.
-        I have the hardware and the motivation and I expect to announce the availability of support the STM32F4-Discovery in a later NuttX release.
+        The basic port for the STM32F-Discovery was contributed by Mike Smith and was first released in NuttX-6.14.
       </p>
     </ul>
   </td>
diff --git a/nuttx/configs/stm32f4discovery/README.txt b/nuttx/configs/stm32f4discovery/README.txt
new file mode 100755
index 000000000..2675bbb42
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/README.txt
@@ -0,0 +1,455 @@
+README
+======
+
+This README discusses issues unique to NuttX configurations for the
+STMicro STM32F4 Discovery development board.
+
+Contents
+========
+
+  - Development Environment
+  - GNU Toolchain Options
+  - IDEs
+  - NuttX buildroot Toolchain
+  - stm32f4discovery-specific Configuration Options
+  - LEDs
+  - PWM
+  - Configurations
+
+Development Environment
+=======================
+
+  Either Linux or Cygwin on Windows can be used for the development environment.
+  The source has been built only using the GNU toolchain (see below).  Other
+  toolchains will likely cause problems. Testing was performed using the Cygwin
+  environment because the Raisonance R-Link emulatator and some RIDE7 development tools
+  were used and those tools works only under Windows.
+
+GNU Toolchain Options
+=====================
+
+  The NuttX make system has been modified to support the following different
+  toolchain options.
+
+  1. The CodeSourcery GNU toolchain,
+  2. The devkitARM GNU toolchain,
+  3. Raisonance GNU toolchain, or
+  4. The NuttX buildroot Toolchain (see below).
+
+  All testing has been conducted using the CodeSourcery toolchain for Windows.  To use
+  the devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
+  add one of the following configuration options to your .config (or defconfig)
+  file:
+
+    CONFIG_STM32_CODESOURCERYW=y  : CodeSourcery under Windows
+    CONFIG_STM32_CODESOURCERYL=y  : CodeSourcery under Linux
+    CONFIG_STM32_DEVKITARM=y      : devkitARM under Windows
+    CONFIG_STM32_RAISONANCE=y     : Raisonance RIDE7 under Windows
+    CONFIG_STM32_BUILDROOT=y      : NuttX buildroot under Linux or Cygwin (default)
+
+  If you change the default toolchain, then you may also have to modify the PATH in
+  the setenv.h file if your make cannot find the tools.
+
+  NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
+  Windows native toolchains.  The CodeSourcey (for Linux) and NuttX buildroot
+  toolchains are Cygwin and/or Linux native toolchains. There are several limitations
+  to using a Windows based toolchain in a Cygwin environment.  The three biggest are:
+
+  1. The Windows toolchain cannot follow Cygwin paths.  Path conversions are
+     performed automatically in the Cygwin makefiles using the 'cygpath' utility
+     but you might easily find some new path problems.  If so, check out 'cygpath -w'
+
+  2. Windows toolchains cannot follow Cygwin symbolic links.  Many symbolic links
+     are used in Nuttx (e.g., include/arch).  The make system works around these
+     problems for the Windows tools by copying directories instead of linking them.
+     But this can also cause some confusion for you:  For example, you may edit
+     a file in a "linked" directory and find that your changes had no effect.
+     That is because you are building the copy of the file in the "fake" symbolic
+     directory.  If you use a Windows toolchain, you should get in the habit of
+     making like this:
+
+       make clean_context all
+
+     An alias in your .bashrc file might make that less painful.
+
+  3. Dependencies are not made when using Windows versions of the GCC.  This is
+     because the dependencies are generated using Windows pathes which do not
+     work with the Cygwin make.
+
+     Support has been added for making dependencies with the windows-native toolchains.
+     That support can be enabled by modifying your Make.defs file as follows:
+
+    -  MKDEP                = $(TOPDIR)/tools/mknulldeps.sh
+    +  MKDEP                = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
+
+     If you have problems with the dependency build (for example, if you are not
+     building on C:), then you may need to modify tools/mkdeps.sh
+
+  NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
+  level of -Os (See Make.defs).  It will work with -O0, -O1, or -O2, but not with
+  -Os.
+
+  NOTE 2: The devkitARM toolchain includes a version of MSYS make.  Make sure that
+  the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
+  path or will get the wrong version of make.
+
+IDEs
+====
+
+  NuttX is built using command-line make.  It can be used with an IDE, but some
+  effort will be required to create the project.
+  
+  Makefile Build
+  --------------
+  Under Eclipse, it is pretty easy to set up an "empty makefile project" and
+  simply use the NuttX makefile to build the system.  That is almost for free
+  under Linux.  Under Windows, you will need to set up the "Cygwin GCC" empty
+  makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
+  there is a lot of help on the internet).
+
+  Native Build
+  ------------
+  Here are a few tips before you start that effort:
+
+  1) Select the toolchain that you will be using in your .config file
+  2) Start the NuttX build at least one time from the Cygwin command line
+     before trying to create your project.  This is necessary to create
+     certain auto-generated files and directories that will be needed.
+  3) Set up include pathes:  You will need include/, arch/arm/src/stm32,
+     arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
+  4) All assembly files need to have the definition option -D __ASSEMBLY__
+     on the command line.
+
+  Startup files will probably cause you some headaches.  The NuttX startup file
+  is arch/arm/src/stm32/stm32_vectors.S.  With RIDE, I have to build NuttX
+  one time from the Cygwin command line in order to obtain the pre-built
+  startup object needed by RIDE.
+
+NuttX buildroot Toolchain
+=========================
+
+  A GNU GCC-based toolchain is assumed.  The files */setenv.sh should
+  be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
+  different from the default in your PATH variable).
+
+  If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
+  SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
+  This GNU toolchain builds and executes in the Linux or Cygwin environment.
+
+  1. You must have already configured Nuttx in <some-dir>/nuttx.
+
+     cd tools
+     ./configure.sh stm32f4discovery/<sub-dir>
+
+  2. Download the latest buildroot package into <some-dir>
+
+  3. unpack the buildroot tarball.  The resulting directory may
+     have versioning information on it like buildroot-x.y.z.  If so,
+     rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
+
+  4. cd <some-dir>/buildroot
+
+  5. cp configs/cortexm3-defconfig-4.3.3 .config
+
+  6. make oldconfig
+
+  7. make
+
+  8. Edit setenv.h, if necessary, so that the PATH variable includes
+     the path to the newly built binaries.
+
+  See the file configs/README.txt in the buildroot source tree.  That has more
+  detailed PLUS some special instructions that you will need to follow if you are
+  building a Cortex-M3 toolchain for Cygwin under Windows.
+
+LEDs
+====
+
+The stm32f4discovery board has four LEDs; green, organge, red and blue on the
+board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
+defined.  In that case, the usage by the board port is defined in
+include/board.h and src/up_leds.c. The LEDs are used to encode OS-related\
+events as follows:
+
+	SYMBOL				Meaning					LED1*	LED2	LED3	LED4
+                                                green   orange  red     blue
+	-------------------	-----------------------	-------	-------	-------	------
+	LED_STARTED			NuttX has been started	ON		OFF		OFF		OFF
+	LED_HEAPALLOCATE	Heap has been allocated	OFF		ON		OFF		OFF
+	LED_IRQSENABLED		Interrupts enabled		ON		ON		OFF		OFF
+	LED_STACKCREATED	Idle stack created		OFF		OFF		ON		OFF
+	LED_INIRQ			In an interrupt**		ON		N/C		N/C		OFF
+	LED_SIGNAL			In a signal handler***  N/C		ON		N/C		OFF
+	LED_ASSERTION		An assertion failed		ON		ON		N/C		OFF
+	LED_PANIC			The system has crashed	N/C		N/C		N/C		ON
+    LED_IDLE            STM32 is is sleep mode  (Optional, not used)
+
+  * If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
+    and these LEDs will give you some indication of where the failure was
+ ** The normal state is LED3 ON and LED1 faintly glowing.  This faint glow
+    is because of timer interupts that result in the LED being illuminated
+    on a small proportion of the time.
+*** LED2 may also flicker normally if signals are processed.
+
+PWM
+===
+
+The stm32f4discovery has no real on-board PWM devices, but the board can be
+configured to output a pulse train using TIM4 CH2 on PD3.  This pin is
+available next to the audio jack.
+
+stm32f4discovery-specific Configuration Options
+============================================
+
+	CONFIG_ARCH - Identifies the arch/ subdirectory.  This should
+	   be set to:
+
+	   CONFIG_ARCH=arm
+
+	CONFIG_ARCH_family - For use in C code:
+
+	   CONFIG_ARCH_ARM=y
+
+	CONFIG_ARCH_architecture - For use in C code:
+
+	   CONFIG_ARCH_CORTEXM4=y
+
+	CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+
+	   CONFIG_ARCH_CHIP=stm32
+
+	CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
+	   chip:
+
+	   CONFIG_ARCH_CHIP_STM32F407IG=y
+
+    CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
+       configuration features.
+
+       CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
+ 
+	CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
+	   hence, the board that supports the particular chip or SoC.
+
+	   CONFIG_ARCH_BOARD=stm32f4discovery (for the stm32f4discovery development board)
+
+	CONFIG_ARCH_BOARD_name - For use in C code
+
+	   CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y
+
+	CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
+	   of delay loops
+
+	CONFIG_ENDIAN_BIG - define if big endian (default is little
+	   endian)
+
+	CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
+
+	   CONFIG_DRAM_SIZE=0x00010000 (64Kb)
+
+	CONFIG_DRAM_START - The start address of installed DRAM
+
+	   CONFIG_DRAM_START=0x20000000
+
+	CONFIG_DRAM_END - Last address+1 of installed RAM
+
+	   CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+
+	CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization
+
+	   CONFIG_ARCH_IRQPRIO=y
+
+	CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU)
+
+	   CONFIG_ARCH_FPU=y
+
+	CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
+	   have LEDs
+
+	CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+	   stack. If defined, this symbol is the size of the interrupt
+	    stack in bytes.  If not defined, the user task stacks will be
+	  used during interrupt handling.
+
+	CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+
+	CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+
+	CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+	   cause a 100 second delay during boot-up.  This 100 second delay
+	   serves no purpose other than it allows you to calibratre
+	   CONFIG_ARCH_LOOPSPERMSEC.  You simply use a stop watch to measure
+	   the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
+	   the delay actually is 100 seconds.
+
+  Individual subsystems can be enabled:
+
+	AHB1
+	----
+	CONFIG_STM32_CRC
+	CONFIG_STM32_BKPSRAM
+	CONFIG_STM32_CCMDATARAM
+	CONFIG_STM32_DMA1
+	CONFIG_STM32_DMA2
+	CONFIG_STM32_ETHMAC
+	CONFIG_STM32_OTGHS
+
+	AHB2
+	----
+	CONFIG_STM32_DCMI
+	CONFIG_STM32_CRYP
+	CONFIG_STM32_HASH
+	CONFIG_STM32_RNG
+	CONFIG_STM32_OTGFS
+
+	AHB3
+	----
+	CONFIG_STM32_FSMC
+
+	APB1
+	----
+	CONFIG_STM32_TIM2
+	CONFIG_STM32_TIM3
+	CONFIG_STM32_TIM4
+	CONFIG_STM32_TIM5
+	CONFIG_STM32_TIM6
+	CONFIG_STM32_TIM7
+	CONFIG_STM32_TIM12
+	CONFIG_STM32_TIM13
+	CONFIG_STM32_TIM14
+	CONFIG_STM32_WWDG
+	CONFIG_STM32_SPI2
+	CONFIG_STM32_SPI3
+	CONFIG_STM32_USART2
+	CONFIG_STM32_USART3
+	CONFIG_STM32_UART4
+	CONFIG_STM32_UART5
+	CONFIG_STM32_I2C1
+	CONFIG_STM32_I2C2
+	CONFIG_STM32_I2C3
+	CONFIG_STM32_CAN1
+	CONFIG_STM32_CAN2
+	CONFIG_STM32_DAC1
+	CONFIG_STM32_DAC2
+	CONFIG_STM32_PWR -- Required for RTC
+
+	APB2
+	----
+	CONFIG_STM32_TIM1
+	CONFIG_STM32_TIM8
+	CONFIG_STM32_USART1
+	CONFIG_STM32_USART6
+	CONFIG_STM32_ADC1
+	CONFIG_STM32_ADC2
+	CONFIG_STM32_ADC3
+	CONFIG_STM32_SDIO
+	CONFIG_STM32_SPI1
+	CONFIG_STM32_SYSCFG
+	CONFIG_STM32_TIM9
+	CONFIG_STM32_TIM10
+	CONFIG_STM32_TIM11
+
+  Timer and I2C devices may need to the following to force power to be applied
+  unconditionally at power up.  (Otherwise, the device is powered when it is
+  initialized).
+
+    CONFIG_STM32_FORCEPOWER
+
+  Timer devices may be used for different purposes.  One special purpose is
+  to generate modulated outputs for such things as motor control.  If CONFIG_STM32_TIMn
+  is defined (as above) then the following may also be defined to indicate that
+  the timer is intended to be used for pulsed output modulation, ADC conversion,
+  or DAC conversion. Note that ADC/DAC require two definition:  Not only do you have
+  to assign the timer (n) for used by the ADC or DAC, but then you also have to
+  configure which ADC or DAC (m) it is assigned to.
+
+	CONFIG_STM32_TIMn_PWM   Reserve timer n for use by PWM, n=1,..,14
+	CONFIG_STM32_TIMn_ADC   Reserve timer n for use by ADC, n=1,..,14
+	CONFIG_STM32_TIMn_ADCm  Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
+	CONFIG_STM32_TIMn_DAC   Reserve timer n for use by DAC, n=1,..,14
+	CONFIG_STM32_TIMn_DACm  Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
+
+  For each timer that is enabled for PWM usage, we need the following additional
+  configuration settings:
+
+	CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
+ 
+  NOTE: The STM32 timers are each capable of generating different signals on
+  each of the four channels with different duty cycles.  That capability is
+  not supported by this driver:  Only one output channel per timer.
+
+  JTAG Enable settings (by default only SW-DP is enabled):
+
+	CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+	CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+	  but without JNTRST.
+	CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
+
+  STM3240xxx specific device driver settings
+
+	CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
+           m (m=4,5) for the console and ttys0 (default is the USART1).
+	CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
+	   This specific the size of the receive buffer
+	CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
+	   being sent.  This specific the size of the transmit buffer
+	CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART.  Must be
+	CONFIG_U[S]ARTn_BITS - The number of bits.  Must be either 7 or 8.
+	CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+	CONFIG_U[S]ARTn_2STOP - Two stop bits
+
+	CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
+	  support. Non-interrupt-driven, poll-waiting is recommended if the
+	  interrupt rate would be to high in the interrupt driven case.
+	CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
+	  Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
+
+	CONFIG_SDIO_DMA - Support DMA data transfers.  Requires CONFIG_STM32_SDIO
+	  and CONFIG_STM32_DMA2.
+	CONFIG_SDIO_PRI - Select SDIO interrupt prority.  Default: 128
+	CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority. 
+	  Default:  Medium
+	CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode.  Default:
+	  4-bit transfer mode.
+
+Configurations
+==============
+
+Each stm32f4discovery configuration is maintained in a sudirectory and
+can be selected as follow:
+
+	cd tools
+	./configure.sh stm32f4discovery/<subdir>
+	cd -
+	. ./setenv.sh
+
+Where <subdir> is one of the following:
+
+  ostest:
+  ------
+    This configuration directory, performs a simple OS test using
+    examples/ostest.  By default, this project assumes that you are
+    using the DFU bootloader.
+
+    CONFIG_STM32_CODESOURCERYW=y  : CodeSourcery under Windows
+
+  nsh:
+  ---
+    Configures the NuttShell (nsh) located at apps/examples/nsh.  The
+    Configuration enables both the serial and telnet NSH interfaces.
+
+    CONFIG_STM32_CODESOURCERYL=y              : CodeSourcery under Linux / Mac OS X
+
+    NOTES:
+    1. This example supports the PWM test (apps/examples/pwm) but this must
+       be manually enabled by selecting:
+
+       CONFIG_PWM=y              : Enable the generic PWM infrastructure
+       CONFIG_STM32_TIM4_PWM=y   : Use TIM4 to generate PWM output
+
+       See also apps/examples/README.txt
+
+       Special PWM-only debug options:
+
+       CONFIG_DEBUG_PWM
+
diff --git a/nuttx/configs/stm32f4discovery/include/board.h b/nuttx/configs/stm32f4discovery/include/board.h
new file mode 100755
index 000000000..8a9ce5e67
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/include/board.h
@@ -0,0 +1,312 @@
+/************************************************************************************
+ * configs/stm32f4discovery/include/board.h
+ * include/arch/board/board.h
+ *
+ *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+#ifndef __ARCH_BOARD_BOARD_H
+#define __ARCH_BOARD_BOARD_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+#include "stm32_rcc.h"
+#include "stm32_sdio.h"
+#include "stm32_internal.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+/* The STM32F4 Discovery board features a single 8MHz crystal.  Space is provided
+ * for a 32kHz RTC backup crystal, but it is not stuffed.
+ *
+ * This is the canonical configuration:
+ *   System Clock source           : PLL (HSE)
+ *   SYSCLK(Hz)                    : 168000000    Determined by PLL configuration
+ *   HCLK(Hz)                      : 168000000    (STM32_RCC_CFGR_HPRE)
+ *   AHB Prescaler                 : 1            (STM32_RCC_CFGR_HPRE)
+ *   APB1 Prescaler                : 4            (STM32_RCC_CFGR_PPRE1)
+ *   APB2 Prescaler                : 2            (STM32_RCC_CFGR_PPRE2)
+ *   HSE Frequency(Hz)             : 25000000     (STM32_BOARD_XTAL)
+ *   PLLM                          : 8            (STM32_PLLCFG_PLLM)
+ *   PLLN                          : 336          (STM32_PLLCFG_PLLN)
+ *   PLLP                          : 2            (STM32_PLLCFG_PLLP)
+ *   PLLQ                          : 7            (STM32_PLLCFG_PPQ)
+ *   Main regulator output voltage : Scale1 mode  Needed for high speed SYSCLK
+ *   Flash Latency(WS)             : 5
+ *   Prefetch Buffer               : OFF
+ *   Instruction cache             : ON
+ *   Data cache                    : ON
+ *   Require 48MHz for USB OTG FS, : Enabled
+ *   SDIO and RNG clock
+ */
+
+/* HSI - 16 MHz RC factory-trimmed
+ * LSI - 32 KHz RC
+ * HSE - On-board crystal frequency is 25MHz
+ * LSE - 32.768 kHz
+ */
+
+#define STM32_BOARD_XTAL        8000000ul
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+#define STM32_LSE_FREQUENCY     32768
+
+/* Main PLL Configuration.
+ *
+ * PLL source is HSE
+ * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
+ *         = (25,000,000 / 25) * 336
+ *         = 336,000,000
+ * SYSCLK  = PLL_VCO / PLLP
+ *         = 336,000,000 / 2 = 168,000,000
+ * USB OTG FS, SDIO and RNG Clock
+ *         =  PLL_VCO / PLLQ
+ *         = 48,000,000
+ */
+
+#define STM32_PLLCFG_PLLM       RCC_PLLCFG_PLLM(8)
+#define STM32_PLLCFG_PLLN       RCC_PLLCFG_PLLN(336)
+#define STM32_PLLCFG_PLLP       RCC_PLLCFG_PLLP_2
+#define STM32_PLLCFG_PPQ        RCC_PLLCFG_PLLQ(7)
+
+#define STM32_SYSCLK_FREQUENCY  168000000ul
+
+/* AHB clock (HCLK) is SYSCLK (168MHz) */
+
+#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK  /* HCLK  = SYSCLK / 1 */
+#define STM32_HCLK_FREQUENCY    STM32_SYSCLK_FREQUENCY
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY  /* same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */
+
+#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd4     /* PCLK1 = HCLK / 4 */
+#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/4)
+
+/* Timers driven from APB1 will be twice PCLK1 */
+
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */
+
+#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLKd2     /* PCLK2 = HCLK / 2 */
+#define STM32_PCLK2_FREQUENCY   (STM32_HCLK_FREQUENCY/2)
+
+/* Timers driven from APB2 will be twice PCLK2 */
+
+#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB2_TIM9_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB2_TIM10_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB2_TIM11_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
+ * otherwise frequency is 2xAPBx. 
+ * Note: TIM1,8 are on APB2, others on APB1
+ */
+
+#define STM32_TIM18_FREQUENCY   STM32_HCLK_FREQUENCY
+#define STM32_TIM27_FREQUENCY   STM32_HCLK_FREQUENCY
+
+/* LED definitions ******************************************************************/
+/* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any
+ * way.  The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with stm32_setled() */
+
+#define BOARD_LED1        0
+#define BOARD_LED2        1
+#define BOARD_LED3        2
+#define BOARD_LED4        3
+#define BOARD_NLEDS       4
+
+#define BOARD_LED_GREEN   BOARD_LED1
+#define BOARD_LED_ORANGE  BOARD_LED2
+#define BOARD_LED_RED     BOARD_LED3
+#define BOARD_LED_BLUE    BOARD_LED4
+
+/* LED bits for use with stm32_setleds() */
+
+#define BOARD_LED1_BIT    (1 << BOARD_LED1)
+#define BOARD_LED2_BIT    (1 << BOARD_LED2)
+#define BOARD_LED3_BIT    (1 << BOARD_LED3)
+#define BOARD_LED4_BIT    (1 << BOARD_LED4)
+
+/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 4 LEDs on board the
+ * stm32f4discovery.  The following definitions describe how NuttX controls the LEDs:
+ */
+
+#define LED_STARTED       0  /* LED1 */
+#define LED_HEAPALLOCATE  1  /* LED2 */
+#define LED_IRQSENABLED   2  /* LED1 + LED2 */
+#define LED_STACKCREATED  3  /* LED3 */
+#define LED_INIRQ         4  /* LED1 + LED3 */
+#define LED_SIGNAL        5  /* LED2 + LED3 */
+#define LED_ASSERTION     6  /* LED1 + LED2 + LED3 */
+#define LED_PANIC         7  /* N/C  + N/C  + N/C + LED4 */
+
+/* Button definitions ***************************************************************/
+/* The STM32F4 Discovery supports one button: */
+
+#define BUTTON_USER        0
+
+#define NUM_BUTTONS        1
+
+#define BUTTON_USER_BIT    (1 << BUTTON_USER)
+
+/* Alternate function pin selections ************************************************/
+
+/* UART2:
+ *
+ * The STM32F4 Discovery has no on-board serial devices, but the console is
+ * brought out to PA2 (TX) and PA3 (RX) for connection to an external serial device.
+ */
+
+#define GPIO_USART2_RX GPIO_USART2_RX_1
+#define GPIO_USART2_TX GPIO_USART2_TX_1
+
+/* PWM
+ *
+ * The STM32F4 Discovery has no real on-board PWM devices, but the board can be
+ * configured to output a pulse train using TIM4 CH2 on PD13.
+ */
+
+#define GPIO_TIM4_CH2OUT GPIO_TIM4_CH2OUT_2
+
+/* SPI */
+
+#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1
+#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1
+#define GPIO_SPI1_SCK  GPIO_SPI1_SCK_1
+
+/************************************************************************************
+ * Public Data
+ ************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+#undef EXTERN
+#if defined(__cplusplus)
+#define EXTERN extern "C"
+extern "C" {
+#else
+#define EXTERN extern
+#endif
+
+/************************************************************************************
+ * Public Function Prototypes
+ ************************************************************************************/
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the intitialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+EXTERN void stm32_boardinitialize(void);
+
+/************************************************************************************
+ * Name:  stm32_ledinit, stm32_setled, and stm32_setleds
+ *
+ * Description:
+ *   If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs.  If
+ *   CONFIG_ARCH_LEDS is not defined, then the following interfacesare available to
+ *   control the LEDs from user applications.
+ *
+ ************************************************************************************/
+
+#ifndef CONFIG_ARCH_LEDS
+EXTERN void stm32_ledinit(void);
+EXTERN void stm32_setled(int led, bool ledon);
+EXTERN void stm32_setleds(uint8_t ledset);
+#endif
+
+/************************************************************************************
+ * Button support.
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ *   After up_buttoninit() has been called, up_buttons() may be called to
+ *   collect the state of all buttons.  up_buttons() returns an 8-bit bit set
+ *   with each bit associated with a button.  See the BUTTON_*_BIT
+ *   definitions in board.h for the meaning of each bit.
+ *
+ *   up_irqbutton() may be called to register an interrupt handler that will
+ *   be called when a button is depressed or released.  The ID value is a
+ *   button enumeration value that uniquely identifies a button resource. See the
+ *   BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.  The previous interrupt handler address is returned (so that it may
+ *   restored, if so desired).
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_ARCH_BUTTONS
+EXTERN void up_buttoninit(void);
+EXTERN uint8_t up_buttons(void);
+#ifdef CONFIG_ARCH_IRQBUTTONS
+EXTERN xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
+#endif
+#endif
+
+#undef EXTERN
+#if defined(__cplusplus)
+}
+#endif
+
+#endif /* __ASSEMBLY__ */
+#endif  /* __ARCH_BOARD_BOARD_H */
diff --git a/nuttx/configs/stm32f4discovery/nsh/Make.defs b/nuttx/configs/stm32f4discovery/nsh/Make.defs
new file mode 100644
index 000000000..3a5bf3aa1
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/nsh/Make.defs
@@ -0,0 +1,170 @@
+############################################################################
+# configs/stm32f4discovery/nsh/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+LDSCRIPT = ld.script
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/nsh/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/stm32f4discovery/nsh/appconfig b/nuttx/configs/stm32f4discovery/nsh/appconfig
new file mode 100644
index 000000000..edd6dda52
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/nsh/appconfig
@@ -0,0 +1,52 @@
+############################################################################
+# configs/stm32f4discovery/nsh/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/nsh
+
+# The NSH application library
+
+CONFIGURED_APPS += nshlib
+
+# Applications configured as an NX built-in commands
+
+ifeq ($(CONFIG_ADC),y)
+CONFIGURED_APPS += examples/adc
+endif
+
+ifeq ($(CONFIG_PWM),y)
+CONFIGURED_APPS += examples/pwm
+endif
diff --git a/nuttx/configs/stm32f4discovery/nsh/defconfig b/nuttx/configs/stm32f4discovery/nsh/defconfig
new file mode 100755
index 000000000..529716409
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/nsh/defconfig
@@ -0,0 +1,1275 @@
+############################################################################
+# configs/stm32f4discovery/nsh/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization
+# CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU)
+#   (But, unfortunately, GCC does not support it).
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM4=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F407VG=y
+CONFIG_ARCH_BOARD=stm32f4discovery
+CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_DRAM_SIZE=0x00030000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_FPU=n
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=n
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+
+#
+# JTAG Enable settings (by default only SW-DP is enabled):
+#
+#   CONFIG_STM32_DFU - Use the DFU bootloader, not JTAG
+#
+# JTAG Enable options:
+#
+#   CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+#   CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+#     but without JNTRST.
+#   CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
+#
+CONFIG_STM32_DFU=n
+CONFIG_STM32_JTAG_FULL_ENABLE=n
+CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n
+CONFIG_STM32_JTAG_SW_ENABLE=y
+
+#
+#  Individual subsystems can be enabled:
+#
+# Individual subsystems can be enabled:
+# AHB1:
+CONFIG_STM32_CRC=n
+CONFIG_STM32_BKPSRAM=n
+CONFIG_STM32_CCMDATARAM=n
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=n
+CONFIG_STM32_ETHMAC=n
+CONFIG_STM32_OTGHS=n
+# AHB2:
+CONFIG_STM32_DCMI=n
+CONFIG_STM32_CRYP=n
+CONFIG_STM32_HASH=n
+CONFIG_STM32_RNG=n
+CONFIG_STM32_OTGFS=y
+# AHB3:
+CONFIG_STM32_FSMC=n
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_TIM12=n
+CONFIG_STM32_TIM13=n
+CONFIG_STM32_TIM14=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI3=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_I2C3=n
+CONFIG_STM32_CAN1=n
+CONFIG_STM32_CAN2=n
+CONFIG_STM32_DAC=n
+CONFIG_STM32_PWR=y
+# APB2:
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=n
+CONFIG_STM32_USART6=n
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_ADC3=n
+CONFIG_STM32_SDIO=n
+CONFIG_STM32_SPI1=y
+CONFIG_STM32_SYSCFG=y
+CONFIG_STM32_TIM9=n
+CONFIG_STM32_TIM10=n
+CONFIG_STM32_TIM11=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM32F40xxx specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=n
+CONFIG_USART2_SERIAL_CONSOLE=y
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=128
+CONFIG_USART2_TXBUFSIZE=128
+CONFIG_USART3_TXBUFSIZE=128
+CONFIG_USART4_TXBUFSIZE=128
+CONFIG_USART5_TXBUFSIZE=128
+
+CONFIG_USART1_RXBUFSIZE=128
+CONFIG_USART2_RXBUFSIZE=128
+CONFIG_USART3_RXBUFSIZE=128
+CONFIG_USART4_RXBUFSIZE=128
+CONFIG_USART5_RXBUFSIZE=128
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F40xxx specific SPI device driver settings
+#
+CONFIG_SPI_EXCHANGE=y
+
+#
+# STM32F40xxx specific CAN device driver settings
+#
+# CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
+#   CONFIG_STM32_CAN2 must also be defined)
+# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
+#   Default: 8
+# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
+#   Default: 4
+# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
+#   mode for testing. The STM32 CAN driver does support loopback mode.
+# CONFIG_CAN1_BAUD - CAN1 BAUD rate.  Required if CONFIG_STM32_CAN1 is defined.
+# CONFIG_CAN2_BAUD - CAN1 BAUD rate.  Required if CONFIG_STM32_CAN2 is defined.
+#
+CONFIG_CAN=n
+#CONFIG_CAN_FIFOSIZE
+#CONFIG_CAN_NPENDINGRTR
+CONFIG_CAN_LOOPBACK=n
+CONFIG_CAN1_BAUD=700000
+CONFIG_CAN2_BAUD=700000
+
+#
+# STM32F40xxx Ethernet device driver settings
+#
+# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
+# CONFIG_STM32_MII - Support Ethernet MII interface
+# CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
+# CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
+# CONFIG_STM32_RMII - Support Ethernet RMII interface
+# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
+# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
+#   may be defined to select full duplex mode. Default: half-duplex
+# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
+#   may be defined to select 100 MBps speed.  Default: 10 Mbps
+# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  The PHY status register address may diff from PHY to PHY.  This
+#   configuration sets the address of the PHY status register.
+# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides bit mask indicating 10 or 100MBps speed.
+# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides the value of the speed bit(s) indicating 100MBps speed.
+# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provide bit mask indicating full or half duplex modes.
+# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides the value of the mode bits indicating full duplex mode.
+# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP).  Not supported
+#   but some hooks are indicated with this condition.
+# CONFIG_STM32_ETHMAC_REGDEBUG - If CONFIG_DEBUG is also enabled, this will
+#   generate far more debug output than you could ever care to see unless you
+#   are debugging low-level Ethernet driver features.
+#
+CONFIG_STM32_PHYADDR=0x01
+CONFIG_STM32_MII=y
+CONFIG_STM32_MII_MCO1=y
+CONFIG_STM32_MII_MCO2=n
+CONFIG_STM32_RMII=n
+CONFIG_STM32_AUTONEG=y
+#CONFIG_STM32_ETHFD
+#CONFIG_STM32_ETH100MB
+CONFIG_STM32_PHYSR=16
+CONFIG_STM32_PHYSR_SPEED=0x0002
+CONFIG_STM32_PHYSR_100MBPS=0x0000
+CONFIG_STM32_PHYSR_MODE=0x0004
+CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004
+CONFIG_STM32_ETH_PTP=n
+CONFIG_STM32_ETHMAC_REGDEBUG=n
+
+
+#
+# PWM configuration
+#
+# The stm32f4discovery has no real on-board PWM devices, but the board can be configured to output
+# a pulse train using TIM4 CH2.  
+#
+CONFIG_PWM=n
+CONFIG_STM32_TIM4=y
+CONFIG_STM32_TIM4_PWM=y
+CONFIG_STM32_TIM4_CHANNEL=2
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_HAVE_CXX - Enable support for C++
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+# CONFIG_SCHED_WAITPID - Enable the waitpid() API
+# CONFIG_SCHED_ATEXIT - Enabled the atexit() API
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_DEBUG_FS=n
+CONFIG_DEBUG_GRAPHICS=n
+CONFIG_DEBUG_LCD=n
+CONFIG_DEBUG_USB=n
+CONFIG_DEBUG_NET=n
+CONFIG_DEBUG_RTC=n
+CONFIG_DEBUG_ANALOG=n
+CONFIG_DEBUG_PWM=n
+CONFIG_DEBUG_CAN=n
+CONFIG_HAVE_CXX=y
+CONFIG_MM_REGIONS=2
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2011
+CONFIG_START_MONTH=12
+CONFIG_START_DAY=6
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=n
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=n
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+CONFIG_SCHED_WAITPID=y
+CONFIG_SCHED_ATEXIT=n
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=n
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=n
+CONFIG_DISABLE_ENVIRON=n
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled
+#   (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added
+#   to force automatic, line-oriented flushing the output buffer
+#   for putc(), fputc(), putchar(), puts(), fputs(), printf(),
+#   fprintf(), and vfprintf().  When a newline is encountered in
+#   the output string, the output buffer will be flushed.  This
+#   (slightly) increases the NuttX footprint but supports the kind
+#   of behavior that people expect for printf().
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STDIO_LINEBUFFER=y
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Framebuffer driver options
+#
+CONFIG_FB_CMAP=n
+CONFIG_FB_HWCURSOR=n
+CONFIG_FB_HWCURSORIMAGE=n
+#CONFIG_FB_HWCURSORSIZE
+#CONFIG_FB_TRANSPARENCY
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=0
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# STM32 SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_SDIO_PRI - Select SDIO interrupt prority.  Default: 128
+# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
+#   Default:  Medium
+# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode.  Default:
+#   4-bit transfer mode.
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=n
+#CONFIG_SDIO_PRI=128
+#CONFIG_SDIO_DMAPRIO
+#CONFIG_SDIO_WIDTH_D1_ONLY
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=n
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+#
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_NOINTS - uIP not called from interrupt level.
+# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no)
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_ARP_IPIN - Harvest IP/MAC address mappings from the ARP table
+#   from incoming IP packets.
+# CONFIG_NET_MULTICAST - Outgoing multi-cast address support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when
+#   looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_NOINTS=n
+CONFIG_NET_MULTIBUFFER=y
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=10
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=562
+CONFIG_NET_TCP=y
+CONFIG_NET_TCP_CONNS=40
+#CONFIG_NET_TCP_READAHEAD_BUFSIZE
+CONFIG_NET_NTCP_READAHEAD_BUFFERS=16
+CONFIG_NET_TCPBACKLOG=y
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=y
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=y
+CONFIG_NET_ICMP_PING=y
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_ARP_IPIN=n
+CONFIG_NET_MULTICAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# RTC Configuration
+#
+# CONFIG_RTC - Enables general support for a hardware RTC.  Specific
+#   architectures may require other specific settings.
+# CONFIG_RTC_DATETIME - There are two general types of RTC:  (1) A simple
+#   battery backed counter that keeps the time when power is down, and (2)
+#    A full date / time RTC the provides the date and time information, often
+#   in BCD format.  If CONFIG_RTC_DATETIME is selected, it specifies this
+#   second kind of RTC. In this case, the RTC is used to "seed" the normal
+#   NuttX timer and the NuttX system timer provides for higher resoution
+#   time.
+# CONFIG_RTC_HIRES - If CONFIG_RTC_DATETIME not selected, then the simple,
+#   battery backed counter is used.  There are two different implementations
+#   of such simple counters based on the time resolution of the counter:
+#   The typical RTC keeps time to resolution of 1 second, usually
+#   supporting a 32-bit time_t value.  In this case, the RTC is used to
+#   "seed" the normal NuttX timer and the NuttX timer provides for higher
+#   resoution time. If CONFIG_RTC_HIRES is enabled in the NuttX configuration,
+#   then the RTC provides higher resolution time and completely replaces the
+#   system timer for purpose of date and time.
+# CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the frequency
+#  of the high resolution RTC must be provided.  If CONFIG_RTC_HIRES is
+#   not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
+# CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an
+#  alarm.  A callback function will be executed when the alarm goes off
+#
+CONFIG_RTC=n
+CONFIG_RTC_DATETIME=y
+CONFIG_RTC_HIRES=n
+CONFIG_RTC_FREQUENCY=n
+CONFIG_RTC_ALARM=n
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Graphics related configuration settings
+#
+# CONFIG_NX
+#   Enables overall support for graphics library and NX
+# CONFIG_NX_MULTIUSER
+#   Configures NX in multi-user mode
+# CONFIG_NX_NPLANES
+#   Some YUV color formats requires support for multiple planes,
+#   one for each color component.  Unless you have such special
+#   hardware, this value should be undefined or set to 1
+# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
+# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
+# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
+# CONFIG_NX_DISABLE_32BPP
+#   NX supports a variety of pixel depths.  You can save some
+#   memory by disabling support for unused color depths.
+# CONFIG_NX_PACKEDMSFIRST
+#   If a pixel depth of less than 8-bits is used, then NX needs
+#   to know if the pixels pack from the MS to LS or from LS to MS
+# CONFIG_NX_LCDDRIVER
+#   By default, NX builds to use a framebuffer driver (see
+#   include/nuttx/fb.h). If this option is defined, NX will
+#   build to use an LCD driver (see include/nuttx/lcd/lcd.h).
+# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
+# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
+# CONFIG_NX_MOUSE
+#   Build in support for mouse input
+# CONFIG_NX_KBD
+#   Build in support of keypad/keyboard input
+# CONFIG_NXTK_BORDERWIDTH
+#   Specifies with with of the border (in pixels) used with
+#   framed windows.  The default is 4.
+# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
+#   Specify the colors of the border used with framed windows.
+#   CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
+#   is normally darker.  The default is medium and dark grey,
+#   respectively
+# CONFIG_NXTK_AUTORAISE
+#   If set, a window will be raised to the top if the mouse position
+#   is over a visible portion of the window.  Default: A mouse
+#   button must be clicked over a visible portion of the window.
+# CONFIG_NXFONTS_CHARBITS
+#   The number of bits in the character set.  Current options are
+#   only 7 and 8.  The default is 7.
+# CONFIG_NXFONT_SANS17X22
+#  This option enables support for a tiny, 17x22 san serif font
+#  (font ID FONTID_SANS17X22 == 14).
+# CONFIG_NXFONT_SANS20X26
+#  This option enables support for a tiny, 20x26 san serif font
+#  (font ID FONTID_SANS20X26 == 15).
+# CONFIG_NXFONT_SANS23X27
+#   This option enables support for a tiny, 23x27 san serif font
+#   (font ID FONTID_SANS23X27 == 1).
+# CONFIG_NXFONT_SANS22X29
+#   This option enables support for a small, 22x29 san serif font
+#   (font ID FONTID_SANS22X29 == 2).
+# CONFIG_NXFONT_SANS28X37
+#   This option enables support for a medium, 28x37 san serif font
+#   (font ID FONTID_SANS28X37 == 3).
+# CONFIG_NXFONT_SANS39X48
+#   This option enables support for a large, 39x48 san serif font
+#   (font ID FONTID_SANS39X48 == 4).
+# CONFIG_NXFONT_SANS17X23B
+#   This option enables support for a tiny, 17x23 san serif bold font
+#   (font ID FONTID_SANS17X23B == 16).
+# CONFIG_NXFONT_SANS20X27B
+#   This option enables support for a tiny, 20x27 san serif bold font
+#   (font ID FONTID_SANS20X27B == 17).
+# CONFIG_NXFONT_SANS22X29B
+#   This option enables support for a small, 22x29 san serif bold font
+#   (font ID FONTID_SANS22X29B == 5).
+# CONFIG_NXFONT_SANS28X37B
+#   This option enables support for a medium, 28x37 san serif bold font
+#   (font ID FONTID_SANS28X37B == 6).
+# CONFIG_NXFONT_SANS40X49B
+#   This option enables support for a large, 40x49 san serif bold font
+#   (font ID FONTID_SANS40X49B == 7).
+# CONFIG_NXFONT_SERIF22X29
+#   This option enables support for a small, 22x29 font (with serifs)
+#   (font ID FONTID_SERIF22X29 == 8).
+# CONFIG_NXFONT_SERIF29X37
+#   This option enables support for a medium, 29x37 font (with serifs)
+#   (font ID FONTID_SERIF29X37 == 9).
+# CONFIG_NXFONT_SERIF38X48
+#   This option enables support for a large, 38x48 font (with serifs)
+#   (font ID FONTID_SERIF38X48 == 10).
+# CONFIG_NXFONT_SERIF22X28B
+#   This option enables support for a small, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF22X28B == 11).
+# CONFIG_NXFONT_SERIF27X38B
+#   This option enables support for a medium, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF27X38B == 12).
+# CONFIG_NXFONT_SERIF38X49B
+#   This option enables support for a large, 38x49 bold font (with serifs)
+#   (font ID FONTID_SERIF38X49B == 13).
+#
+# NX Multi-user only options:
+#
+# CONFIG_NX_BLOCKING
+#   Open the client message queues in blocking mode.  In this case,
+#   nx_eventhandler()  will not return until a message is received and processed.
+# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
+#   Specifies the maximum number of messages that can fit in
+#   the message queues.  No additional resources are allocated, but
+#   this can be set to prevent flooding of the client or server with
+#   too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
+#   messages are pre-allocated).
+#
+CONFIG_NX=n
+CONFIG_NX_MULTIUSER=n
+CONFIG_NX_NPLANES=1
+CONFIG_NX_DISABLE_1BPP=y
+CONFIG_NX_DISABLE_2BPP=y
+CONFIG_NX_DISABLE_4BPP=y
+CONFIG_NX_DISABLE_8BPP=y
+CONFIG_NX_DISABLE_16BPP=n
+CONFIG_NX_DISABLE_24BPP=y
+CONFIG_NX_DISABLE_32BPP=y
+CONFIG_NX_PACKEDMSFIRST=n
+CONFIG_NX_LCDDRIVER=y
+CONFIG_LCD_MAXPOWER=1
+CONFIG_LCD_MAXCONTRAST=1
+CONFIG_NX_MOUSE=y
+CONFIG_NX_KBD=y
+#CONFIG_NXTK_BORDERWIDTH=4
+CONFIG_NXTK_BORDERCOLOR1=0xd69a
+CONFIG_NXTK_BORDERCOLOR2=0xad55
+CONFIG_NXTK_AUTORAISE=n
+CONFIG_NXFONT_SANS17X22=y
+CONFIG_NXFONT_SANS20X26=n
+CONFIG_NXFONT_SANS22X29=n
+CONFIG_NXFONT_SANS23X27=n
+CONFIG_NXFONT_SANS28X37=n
+CONFIG_NXFONT_SANS17X23B=n
+CONFIG_NXFONT_SANS20X27B=y
+CONFIG_NXFONT_SANS22X29B=y
+CONFIG_NXFONT_SANS28X37B=n
+CONFIG_NXFONT_SANS40X49B=n
+CONFIG_NXFONT_SERIF22X29=n
+CONFIG_NXFONT_SERIF29X37=n
+CONFIG_NXFONT_SERIF38X48=n
+CONFIG_NXFONT_SERIF22X28B=n
+CONFIG_NXFONT_SERIF27X38B=n
+CONFIG_NXFONT_SERIF38X49B=n
+CONFIG_NXFONTS_CHARBITS=7
+CONFIG_NX_BLOCKING=y
+CONFIG_NX_MXSERVERMSGS=32
+CONFIG_NX_MXCLIENTMSGS=16
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=y
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_BUILTIN_APPS - Support external registered,
+#   "named" applications that can be executed from the NSH
+#   command line (see apps/README.txt for more information).
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=n
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=y
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/adc
+#
+# CONFIG_ADC - Enabled ADC support
+# CONFIG_NSH_BUILTIN_APPS - Build the ADC test as an NSH built-in function.
+#   Default: Built as a standalone problem
+#
+# CONFIG_EXAMPLES_ADC_DEVPATH - The path to the ADC device. Default: /dev/adc0
+# CONFIG_EXAMPLES_ADC_NSAMPLES - If CONFIG_NSH_BUILTIN_APPS
+#   is defined, then the number of samples is provided on the command line
+#   and this value is ignored.  Otherwise, this number of samples is
+#   collected and the program terminates.  Default:  Samples are collected
+#   indefinitely.
+# CONFIG_EXAMPLES_ADC_GROUPSIZE - The number of samples to read at once.
+#   Default: 4
+
+#
+# Settings for examples/can
+#
+# CONFIG_CAN - Enables CAN support.
+# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
+#   mode for testing. The STM32 CAN driver does support loopback mode.
+# CONFIG_NSH_BUILTIN_APPS - Build the CAN test as an NSH built-in function.
+#   Default: Built as a standalone problem
+#
+# CONFIG_EXAMPLES_CAN_DEVPATH - The path to the CAN device. Default: /dev/can0
+# CONFIG_EXAMPLES_CAN_NMSGS - If CONFIG_NSH_BUILTIN_APPS
+#   is defined, then the number of loops is provided on the command line
+#   and this value is ignored.  Otherwise, this number of CAN message is
+#   collected and the program terminates.  Default:  If built as an NSH
+#   built-in, the default is 32.  Otherwise messages are sent and received
+#   indefinitely.
+
+#
+# Settings for examples/pwm
+#
+# CONFIG_PWM - Enables PWM support.
+# CONFIG_NSH_BUILTIN_APPS - Build the PWM test as an NSH built-in function.
+#   Default: Not built!  The example can only be used as an NSH built-in
+#   application
+#
+# CONFIG_EXAMPLES_PWM_DEVPATH - The path to the PWM device. Default: /dev/pwm0
+# CONFIG_EXAMPLES_PWM_FREQUENCY - The initial PWM frequency.  Default: 100 Hz
+# CONFIG_EXAMPLES_PWM_DUTYPCT - The initial PWM duty as a percentage.  Default: 50%
+# CONFIG_EXAMPLES_PWM_DURATION - The initial PWM pulse train duration in sectonds.
+#    as a percentage.  Default: 5 seconds
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the stm32f4discovery which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/stm32f4discovery/nsh/ld.script b/nuttx/configs/stm32f4discovery/nsh/ld.script
new file mode 100755
index 000000000..1c5fcd4f6
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/nsh/ld.script
@@ -0,0 +1,116 @@
+/****************************************************************************
+ * configs/stm32f4discovery/nsh/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F407VG has 1024Kb of FLASH beginning at address 0x0800:0000 and
+ * 192Kb of SRAM. SRAM is split up into three blocks:
+ *
+ * 1) 112Kb of SRAM beginning at address 0x2000:0000
+ * 2)  16Kb of SRAM beginning at address 0x2001:c000
+ * 3)  64Kb of TCM SRAM beginning at address 0x1000:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 1024K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 112K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/stm32f4discovery/nsh/setenv.sh b/nuttx/configs/stm32f4discovery/nsh/setenv.sh
new file mode 100755
index 000000000..15539bf68
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/nsh/setenv.sh
@@ -0,0 +1,67 @@
+#!/bin/bash
+# configs/stm32f4discovery/nsh/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This the Cygwin path to the location where I installed the RIDE
+# toolchain under windows.  You will also have to edit this if you install
+# the RIDE toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
+
+# This the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This the Cygwin path to the location where I build the buildroot
+# toolchain.
+#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/stm32f4discovery/ostest/Make.defs b/nuttx/configs/stm32f4discovery/ostest/Make.defs
new file mode 100644
index 000000000..5a49387c6
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/ostest/Make.defs
@@ -0,0 +1,170 @@
+############################################################################
+# configs/stm32f4discovery/ostest/Make.defs
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+
+# Setup for the selected toolchain
+
+ifeq ($(CONFIG_STM32_CODESOURCERYW),y)
+  # CodeSourcery under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_CODESOURCERYL),y)
+  # CodeSourcery under Linux
+  CROSSDEV = arm-none-eabi-
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+  MAXOPTIMIZATION = -O2
+endif
+ifeq ($(CONFIG_STM32_DEVKITARM),y)
+  # devkitARM under Windows
+  CROSSDEV = arm-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_RAISONANCE),y)
+  # Raisonance RIDE7 under Windows
+  CROSSDEV = arm-none-eabi-
+  WINTOOL = y
+  ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
+endif
+ifeq ($(CONFIG_STM32_BUILDROOT),y)
+  # NuttX buildroot under Linux or Cygwin
+  CROSSDEV = arm-elf-
+  ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+  MAXOPTIMIZATION = -Os
+endif
+
+LDSCRIPT = ld.script
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/winlink.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/ostest/$(LDSCRIPT)}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/ostest/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ("${CONFIG_DEBUG_SYMBOLS}","y")
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+define PREPROCESS
+	@echo "CPP: $1->$2"
+	@$(CPP) $(CPPFLAGS) $1 -o $2
+endef
+
+define COMPILE
+	@echo "CC: $1"
+	@$(CC) -c $(CFLAGS) $1 -o $2
+endef
+
+define COMPILEXX
+	@echo "CXX: $1"
+	@$(CXX) -c $(CXXFLAGS) $1 -o $2
+endef
+
+define ASSEMBLE
+	@echo "AS: $1"
+	@$(CC) -c $(AFLAGS) $1 -o $2
+endef
+
+define ARCHIVE
+	echo "AR: $2"; \
+	$(AR) $1 $2 || { echo "$(AR) $1 $2 FAILED!" ; exit 1 ; }
+endef
+
+define CLEAN
+	@rm -f *.o *.a
+endef
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+
diff --git a/nuttx/configs/stm32f4discovery/ostest/appconfig b/nuttx/configs/stm32f4discovery/ostest/appconfig
new file mode 100644
index 000000000..266c7e327
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/ostest/appconfig
@@ -0,0 +1,39 @@
+############################################################################
+# configs/stm32f4discovery/ostest/appconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+# Path to example in apps/examples containing the user_start entry point
+
+CONFIGURED_APPS += examples/ostest
+
diff --git a/nuttx/configs/stm32f4discovery/ostest/defconfig b/nuttx/configs/stm32f4discovery/ostest/defconfig
new file mode 100755
index 000000000..f3b8e73f0
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/ostest/defconfig
@@ -0,0 +1,1473 @@
+############################################################################
+# configs/stm32f4discovery/ostest/defconfig
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+#
+# architecture selection
+#
+# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
+#   processor architecture.
+# CONFIG_ARCH_family - for use in C code.  This identifies the
+#   particular chip family that the architecture is implemented
+#   in.
+# CONFIG_ARCH_architecture - for use in C code.  This identifies the
+#   specific architecture within the chip familyl.
+# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
+# CONFIG_ARCH_CHIP_name - For use in C code
+# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
+#   the board that supports the particular chip or SoC.
+# CONFIG_ARCH_BOARD_name - for use in C code
+# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
+# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
+# CONFIG_DRAM_SIZE - Describes the installed DRAM.
+# CONFIG_DRAM_START - The start address of DRAM (physical)
+# CONFIG_DRAM_END - Last address+1 of installed RAM
+# CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization
+# CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU)
+#   (But, unfortunately, GCC does not support it).
+# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
+#   stack. If defined, this symbol is the size of the interrupt
+#   stack in bytes.  If not defined, the user task stacks will be
+#   used during interrupt handling.
+# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
+# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
+# CONFIG_ARCH_LEDS -  Use LEDs to show state. Unique to board architecture.
+# CONFIG_ARCH_BUTTONS -  Enable support for buttons. Unique to board architecture.
+# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
+#   cause a 100 second delay during boot-up.  This 100 second delay
+#   serves no purpose other than it allows you to calibrate
+#   CONFIG_BOARD_LOOPSPERMSEC.  You simply use a stop watch to measure
+#   the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
+#   the delay actually is 100 seconds.
+# CONFIG_ARCH_DMA - Support DMA initialization
+#
+CONFIG_ARCH=arm
+CONFIG_ARCH_ARM=y
+CONFIG_ARCH_CORTEXM4=y
+CONFIG_ARCH_CHIP=stm32
+CONFIG_ARCH_CHIP_STM32F407VG=y
+CONFIG_ARCH_BOARD=stm32f4discovery
+CONFIG_ARCH_BOARD_STM32F4_DISCOVERY=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_DRAM_SIZE=0x00030000
+CONFIG_DRAM_START=0x20000000
+CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
+CONFIG_ARCH_IRQPRIO=y
+CONFIG_ARCH_FPU=n
+CONFIG_ARCH_INTERRUPTSTACK=n
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_BOOTLOADER=n
+CONFIG_ARCH_LEDS=y
+CONFIG_ARCH_BUTTONS=n
+CONFIG_ARCH_CALIBRATION=n
+CONFIG_ARCH_DMA=n
+
+#
+# Identify toolchain and linker options
+#
+CONFIG_STM32_CODESOURCERYW=n
+CONFIG_STM32_CODESOURCERYL=y
+CONFIG_STM32_DEVKITARM=n
+CONFIG_STM32_RAISONANCE=n
+CONFIG_STM32_BUILDROOT=n
+
+#
+# JTAG Enable settings (by default only SW-DP is enabled):
+#
+#   CONFIG_STM32_DFU - Use the DFU bootloader, not JTAG
+#
+# JTAG Enable options:
+#
+#   CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+#   CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
+#     but without JNTRST.
+#   CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
+#
+CONFIG_STM32_DFU=n
+CONFIG_STM32_JTAG_FULL_ENABLE=n
+CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n
+CONFIG_STM32_JTAG_SW_ENABLE=y
+
+#
+#  Individual subsystems can be enabled:
+#
+# Individual subsystems can be enabled:
+# AHB1:
+CONFIG_STM32_CRC=n
+CONFIG_STM32_BKPSRAM=n
+CONFIG_STM32_CCMDATARAM=n
+CONFIG_STM32_DMA1=n
+CONFIG_STM32_DMA2=n
+CONFIG_STM32_ETHMAC=n
+CONFIG_STM32_OTGHS=n
+# AHB2:
+CONFIG_STM32_DCMI=n
+CONFIG_STM32_CRYP=n
+CONFIG_STM32_HASH=n
+CONFIG_STM32_RNG=n
+CONFIG_STM32_OTGFS=n
+# AHB3:
+CONFIG_STM32_FSMC=n
+# APB1:
+CONFIG_STM32_TIM2=n
+CONFIG_STM32_TIM3=n
+CONFIG_STM32_TIM4=n
+CONFIG_STM32_TIM5=n
+CONFIG_STM32_TIM6=n
+CONFIG_STM32_TIM7=n
+CONFIG_STM32_TIM12=n
+CONFIG_STM32_TIM13=n
+CONFIG_STM32_TIM14=n
+CONFIG_STM32_WWDG=n
+CONFIG_STM32_SPI2=n
+CONFIG_STM32_SPI3=n
+CONFIG_STM32_USART2=y
+CONFIG_STM32_USART3=n
+CONFIG_STM32_UART4=n
+CONFIG_STM32_UART5=n
+CONFIG_STM32_I2C1=n
+CONFIG_STM32_I2C2=n
+CONFIG_STM32_I2C3=n
+CONFIG_STM32_CAN1=n
+CONFIG_STM32_CAN2=n
+CONFIG_STM32_DAC=n
+CONFIG_STM32_PWR=n
+# APB2:
+CONFIG_STM32_TIM1=n
+CONFIG_STM32_TIM8=n
+CONFIG_STM32_USART1=n
+CONFIG_STM32_USART6=n
+CONFIG_STM32_ADC1=n
+CONFIG_STM32_ADC2=n
+CONFIG_STM32_ADC3=n
+CONFIG_STM32_SDIO=n
+CONFIG_STM32_SPI1=n
+CONFIG_STM32_SYSCFG=y
+CONFIG_STM32_TIM9=n
+CONFIG_STM32_TIM10=n
+CONFIG_STM32_TIM11=n
+
+#
+# Timer and I2C devices may need to the following to force power to be applied:
+#
+#CONFIG_STM32_FORCEPOWER=y
+
+#
+# STM3240xxx specific serial device driver settings
+#
+# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
+#   console and ttys0 (default is the USART1).
+# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
+#   This specific the size of the receive buffer
+# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
+#   being sent.  This specific the size of the transmit buffer
+# CONFIG_USARTn_BAUD - The configure BAUD of the UART.  Must be
+# CONFIG_USARTn_BITS - The number of bits.  Must be either 7 or 8.
+# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
+# CONFIG_USARTn_2STOP - Two stop bits
+#
+CONFIG_USART1_SERIAL_CONSOLE=n
+CONFIG_USART2_SERIAL_CONSOLE=y
+CONFIG_USART3_SERIAL_CONSOLE=n
+CONFIG_USART4_SERIAL_CONSOLE=n
+CONFIG_USART5_SERIAL_CONSOLE=n
+
+CONFIG_USART1_TXBUFSIZE=128
+CONFIG_USART2_TXBUFSIZE=128
+CONFIG_USART3_TXBUFSIZE=128
+CONFIG_USART4_TXBUFSIZE=128
+CONFIG_USART5_TXBUFSIZE=128
+
+CONFIG_USART1_RXBUFSIZE=128
+CONFIG_USART2_RXBUFSIZE=128
+CONFIG_USART3_RXBUFSIZE=128
+CONFIG_USART4_RXBUFSIZE=128
+CONFIG_USART5_RXBUFSIZE=128
+
+CONFIG_USART1_BAUD=115200
+CONFIG_USART2_BAUD=115200
+CONFIG_USART3_BAUD=115200
+CONFIG_USART4_BAUD=115200
+CONFIG_USART5_BAUD=115200
+
+CONFIG_USART1_BITS=8
+CONFIG_USART2_BITS=8
+CONFIG_USART3_BITS=8
+CONFIG_USART4_BITS=8
+CONFIG_USART5_BITS=8
+
+CONFIG_USART1_PARITY=0
+CONFIG_USART2_PARITY=0
+CONFIG_USART3_PARITY=0
+CONFIG_USART4_PARITY=0
+CONFIG_USART5_PARITY=0
+
+CONFIG_USART1_2STOP=0
+CONFIG_USART2_2STOP=0
+CONFIG_USART3_2STOP=0
+CONFIG_USART4_2STOP=0
+CONFIG_USART5_2STOP=0
+
+#
+# STM32F40xxx specific SSI device driver settings
+#
+# CONFIG_SSIn_DISABLE - select to disable all support for
+#   the SSI
+# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
+#   Poll-waiting is recommended if the interrupt rate would be to
+#   high in the interrupt driven case.
+# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
+#   emptying the Rx FIFO.  If the SPI frequency is high and this
+#   value is large, then larger values of this setting may cause
+#   Rx FIFO overrun errors.  Default: half of the Tx FIFO size (4).
+#
+CONFIG_SSI0_DISABLE=n
+CONFIG_SSI1_DISABLE=y
+CONFIG_SSI_POLLWAIT=y
+#CONFIG_SSI_TXLIMIT=4
+
+#
+# STM32F40xxx specific CAN device driver settings
+#
+# CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
+#   CONFIG_STM32_CAN2 must also be defined)
+# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
+#   Default: 8
+# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
+#   Default: 4
+# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
+#   mode for testing. The STM32 CAN driver does support loopback mode.
+# CONFIG_CAN1_BAUD - CAN1 BAUD rate.  Required if CONFIG_STM32_CAN1 is defined.
+# CONFIG_CAN2_BAUD - CAN1 BAUD rate.  Required if CONFIG_STM32_CAN2 is defined.
+#
+CONFIG_CAN=n
+#CONFIG_CAN_FIFOSIZE
+#CONFIG_CAN_NPENDINGRTR
+CONFIG_CAN_LOOPBACK=n
+CONFIG_CAN1_BAUD=700000
+CONFIG_CAN2_BAUD=700000
+
+#
+# STM32F40xxx Ethernet device driver settings
+#
+# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
+# CONFIG_STM32_MII - Support Ethernet MII interface
+# CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
+# CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
+# CONFIG_STM32_RMII - Support Ethernet RMII interface
+# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
+# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
+#   may be defined to select full duplex mode. Default: half-duplex
+# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
+#   may be defined to select 100 MBps speed.  Default: 10 Mbps
+# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  The PHY status register address may diff from PHY to PHY.  This
+#   configuration sets the address of the PHY status register.
+# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides bit mask indicating 10 or 100MBps speed.
+# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides the value of the speed bit(s) indicating 100MBps speed.
+# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provide bit mask indicating full or half duplex modes.
+# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
+#   defined.  This provides the value of the mode bits indicating full duplex mode.
+# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP).  Not supported
+#   but some hooks are indicated with this condition.
+#
+CONFIG_STM32_PHYADDR=0x01
+CONFIG_STM32_MII=y
+CONFIG_STM32_MII_MCO1=y
+CONFIG_STM32_MII_MCO2=n
+CONFIG_STM32_RMII=n
+CONFIG_STM32_AUTONEG=y
+#CONFIG_STM32_ETHFD
+#CONFIG_STM32_ETH100MBPS
+CONFIG_STM32_PHYSR=16
+CONFIG_STM32_PHYSR_SPEED=0x0002
+CONFIG_STM32_PHYSR_100MBPS=0x0000
+CONFIG_STM32_PHYSR_MODE=0x0004
+CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004
+CONFIG_STM32_ETH_PTP=n
+
+#
+# General build options
+#
+# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
+#   BSPs from www.ridgerun.com using the tools/mkimage.sh script
+# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
+#   used with many different loaders using the GNU objcopy program
+#   Should not be selected if you are not using the GNU toolchain.
+# CONFIG_RAW_BINARY - make a raw binary format file used with many
+#   different loaders using the GNU objcopy program.  This option
+#   should not be selected if you are not using the GNU toolchain.
+# CONFIG_HAVE_LIBM - toolchain supports libm.a
+#
+CONFIG_RRLOAD_BINARY=n
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MOTOROLA_SREC=n
+CONFIG_RAW_BINARY=y
+CONFIG_HAVE_LIBM=n
+
+#
+# General OS setup
+#
+# CONFIG_APPS_DIR - Identifies the relative path to the directory
+#   that builds the application to link with NuttX.  Default: ../apps
+# CONFIG_DEBUG - enables built-in debug options
+# CONFIG_DEBUG_VERBOSE - enables verbose debug output
+# CONFIG_DEBUG_SYMBOLS - build without optimization and with
+#   debug symbols (needed for use with a debugger).
+# CONFIG_HAVE_CXX - Enable support for C++S
+# CONFIG_MM_REGIONS - If the architecture includes multiple
+#   regions of memory to allocate from, this specifies the
+#   number of memory regions that the memory manager must
+#   handle and enables the API mm_addregion(start, end);
+# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
+#   time console output
+# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
+#   or MSEC_PER_TICK=10.  This setting may be defined to
+#   inform NuttX that the processor hardware is providing
+#   system timer interrupts at some interrupt interval other
+#   than 10 msec.
+# CONFIG_RR_INTERVAL - The round robin timeslice will be set
+#   this number of milliseconds;  Round robin scheduling can
+#   be disabled by setting this value to zero.
+# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in 
+#   scheduler to monitor system performance
+# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
+#   task name to save in the TCB.  Useful if scheduler
+#   instrumentation is selected.  Set to zero to disable.
+# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
+#   Used to initialize the internal time logic.
+# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
+#   You would only need this if you are concerned about accurate
+#   time conversions in the past or in the distant future.
+# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
+#   would only need this if you are concerned about accurate
+#   time conversion in the distand past.  You must also define
+#   CONFIG_GREGORIAN_TIME in order to use Julian time.
+# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
+#   provides /dev/console.  Enables stdout, stderr, stdin.
+# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
+#   driver (minimul support)
+# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
+#   errorcheck mutexes. Enables pthread_mutexattr_settype().
+# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
+#   inheritance on mutexes and semaphores. 
+# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
+#   inheritance is enabled.  It defines the maximum number of
+#   different threads (minus one) that can take counts on a
+#   semaphore with priority inheritance support.  This may be 
+#   set to zero if priority inheritance is disabled OR if you
+#   are only using semaphores as mutexes (only one holder) OR
+#   if no more than two threads participate using a counting
+#   semaphore.
+# CONFIG_SEM_NNESTPRIO.  If priority inheritance is enabled,
+#   then this setting is the maximum number of higher priority
+#   threads (minus 1) than can be waiting for another thread
+#   to release a count on a semaphore.  This value may be set
+#   to zero if no more than one thread is expected to wait for
+#   a semaphore.
+# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
+#   by task_create() when a new task is started.  If set, all
+#   files/drivers will appear to be closed in the new task.
+# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
+#   three file descriptors (stdin, stdout, stderr) by task_create()
+#   when a new task is started. If set, all files/drivers will
+#   appear to be closed in the new task except for stdin, stdout,
+#   and stderr.
+# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
+#   desciptors by task_create() when a new task is started. If
+#   set, all sockets will appear to be closed in the new task.
+# CONFIG_SCHED_WORKQUEUE.  Create a dedicated "worker" thread to
+#  handle delayed processing from interrupt handlers.  This feature
+#  is required for some drivers but, if there are not complaints,
+#  can be safely disabled.  The worker thread also performs
+#  garbage collection -- completing any delayed memory deallocations
+#  from interrupt handlers.  If the worker thread is disabled,
+#  then that clean will be performed by the IDLE thread instead
+#  (which runs at the lowest of priority and may not be appropriate
+#  if memory reclamation is of high priority).  If CONFIG_SCHED_WORKQUEUE
+#  is enabled, then the following options can also be used:
+# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
+#  thread.  Default: 50
+# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
+#  work in units of microseconds.  Default: 50*1000 (50 MS).
+# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
+#  thread.  Default: CONFIG_IDLETHREAD_STACKSIZE.
+# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
+#  the worker thread.  Default: 4
+# CONFIG_SCHED_WAITPID - Enable the waitpid() API
+# CONFIG_SCHED_ATEXIT - Enabled the atexit() API
+#
+#CONFIG_APPS_DIR=
+CONFIG_DEBUG=n
+CONFIG_DEBUG_VERBOSE=n
+CONFIG_DEBUG_SYMBOLS=n
+CONFIG_HAVE_CXX=n
+CONFIG_MM_REGIONS=2
+CONFIG_ARCH_LOWPUTC=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_INSTRUMENTATION=n
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_START_YEAR=2009
+CONFIG_START_MONTH=9
+CONFIG_START_DAY=21
+CONFIG_GREGORIAN_TIME=n
+CONFIG_JULIAN_TIME=n
+CONFIG_DEV_CONSOLE=y
+CONFIG_DEV_LOWCONSOLE=y
+CONFIG_MUTEX_TYPES=n
+CONFIG_PRIORITY_INHERITANCE=n
+CONFIG_SEM_PREALLOCHOLDERS=0
+CONFIG_SEM_NNESTPRIO=0
+CONFIG_FDCLONE_DISABLE=n
+CONFIG_FDCLONE_STDIO=n
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SCHED_WORKQUEUE=n
+CONFIG_SCHED_WORKPRIORITY=50
+CONFIG_SCHED_WORKPERIOD=(50*1000)
+CONFIG_SCHED_WORKSTACKSIZE=1024
+CONFIG_SIG_SIGWORK=4
+CONFIG_SCHED_WAITPID=n
+CONFIG_SCHED_ATEXIT=n
+
+#
+# Settings for NXFLAT
+#
+# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
+#  This format will support execution of NuttX binaries located
+#  in a ROMFS filesystem (see examples/nxflat).
+# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
+#  with.  CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
+#  CONFIG_DEBUG_BINFMT have to be defined or
+#  CONFIG_NXFLAT_DUMPBUFFER does nothing.
+# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
+#  is ordered by symbol name
+#
+CONFIG_NXFLAT=n
+CONFIG_NXFLAT_DUMPBUFFER=n
+CONFIG_SYMTAB_ORDEREDBYNAME=y
+
+#
+# The following can be used to disable categories of
+# APIs supported by the OS.  If the compiler supports
+# weak functions, then it should not be necessary to
+# disable functions unless you want to restrict usage
+# of those APIs.
+#
+# There are certain dependency relationships in these
+# features.
+#
+# o mq_notify logic depends on signals to awaken tasks
+#   waiting for queues to become full or empty.
+# o pthread_condtimedwait() depends on signals to wake
+#   up waiting tasks.
+#
+CONFIG_DISABLE_CLOCK=n
+CONFIG_DISABLE_POSIX_TIMERS=n
+CONFIG_DISABLE_PTHREAD=n
+CONFIG_DISABLE_SIGNALS=n
+CONFIG_DISABLE_MQUEUE=n
+CONFIG_DISABLE_MOUNTPOINT=y
+CONFIG_DISABLE_ENVIRON=y
+CONFIG_DISABLE_POLL=y
+
+#
+# Misc libc settings
+#
+# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
+#   little smaller if we do not support fieldwidthes
+#
+CONFIG_NOPRINTF_FIELDWIDTH=n
+
+#
+# Allow for architecture optimized implementations
+#
+# The architecture can provide optimized versions of the
+# following to improve system performance
+#
+CONFIG_ARCH_MEMCPY=n
+CONFIG_ARCH_MEMCMP=n
+CONFIG_ARCH_MEMMOVE=n
+CONFIG_ARCH_MEMSET=n
+CONFIG_ARCH_STRCMP=n
+CONFIG_ARCH_STRCPY=n
+CONFIG_ARCH_STRNCPY=n
+CONFIG_ARCH_STRLEN=n
+CONFIG_ARCH_STRNLEN=n
+CONFIG_ARCH_BZERO=n
+
+#
+# Sizes of configurable things (0 disables)
+#
+# CONFIG_MAX_TASKS - The maximum number of simultaneously
+#   active tasks.  This value must be a power of two.
+# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
+#   of parameters that a task may receive (i.e., maxmum value
+#   of 'argc')
+# CONFIG_NPTHREAD_KEYS - The number of items of thread-
+#   specific data that can be retained
+# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
+#   descriptors (one for each open)
+# CONFIG_NFILE_STREAMS - The maximum number of streams that
+#   can be fopen'ed
+# CONFIG_NAME_MAX - The maximum size of a file name.
+# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
+#   on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled
+#   (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added
+#   to force automatic, line-oriented flushing the output buffer
+#   for putc(), fputc(), putchar(), puts(), fputs(), printf(),
+#   fprintf(), and vfprintf().  When a newline is encountered in
+#   the output string, the output buffer will be flushed.  This
+#   (slightly) increases the NuttX footprint but supports the kind
+#   of behavior that people expect for printf().
+# CONFIG_NUNGET_CHARS - Number of characters that can be
+#   buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
+# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
+#   structures.  The system manages a pool of preallocated
+#   message structures to minimize dynamic allocations
+# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
+#   a fixed payload size given by this settin (does not include
+#   other message structure overhead.
+# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
+#   can be passed to a watchdog handler
+# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
+#   structures.  The system manages a pool of preallocated
+#   watchdog structures to minimize dynamic allocations
+# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
+#   timer structures.  The system manages a pool of preallocated
+#   timer structures to minimize dynamic allocations.  Set to
+#   zero for all dynamic allocations.
+#
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_TASK_ARGS=4
+CONFIG_NPTHREAD_KEYS=4
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NAME_MAX=32
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STDIO_LINEBUFFER=y
+CONFIG_NUNGET_CHARS=2
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_MQ_MAXMSGSIZE=32
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_PREALLOC_TIMERS=4
+
+#
+# Filesystem configuration
+#
+# CONFIG_FS_FAT - Enable FAT filesystem support
+# CONFIG_FAT_SECTORSIZE - Max supported sector size
+# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
+#   file name support.
+# CONFIG_FAT_LFN - Enable FAT long file names.  NOTE:  Microsoft claims
+#   patents on FAT long file name technology.  Please read the
+#   disclaimer in the top-level COPYING file and only enable this
+#   feature if you understand these issues.
+# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
+#   default, maximum long file name is 255 bytes.  This can eat up
+#   a lot of memory (especially stack space).  If you are willing
+#   to live with some non-standard, short long file names, then
+#   define this value.  A good choice would be the same value as
+#   selected for CONFIG_NAME_MAX which will limit the visibility
+#   of longer file names anyway.
+# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
+# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. 
+#   This must have one of the values of 0xff or 0x00.
+#   Default: 0xff.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
+#   Default: 255.
+# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
+#   don't both with file chunks smaller than this number of data bytes.
+#   Default: 32.
+# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
+#   packing files together toward the end of the file or, if file are
+#   deleted at the end of the file, clean up can simply mean erasing
+#   the end of FLASH memory so that it can be re-used again.  However,
+#   doing this can also harm the life of the FLASH part because it can
+#   mean that the tail end of the FLASH is re-used too often. This
+#   threshold determines if/when it is worth erased the tail end of FLASH
+#   and making it available for re-use (and possible over-wear).
+#   Default: 8192.
+# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
+# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
+#   option will enable a limited form of memory mapping that is
+#   implemented by copying whole files into memory.
+#
+CONFIG_FS_FAT=n
+CONFIG_FAT_LCNAMES=n
+CONFIG_FAT_LFN=n
+CONFIG_FAT_MAXFNAME=32
+CONFIG_FS_NXFFS=n
+CONFIG_FS_ROMFS=n
+
+#
+# SPI-based MMC/SD driver
+#
+# CONFIG_MMCSD_NSLOTS
+#   Number of MMC/SD slots supported by the driver
+# CONFIG_MMCSD_READONLY
+#   Provide read-only access (default is read/write)
+# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
+#   Default is 20MHz.
+#
+CONFIG_MMCSD_NSLOTS=0
+CONFIG_MMCSD_READONLY=n
+CONFIG_MMCSD_SPICLOCK=12500000
+
+#
+# Block driver buffering
+#
+# CONFIG_FS_READAHEAD
+#   Enable read-ahead buffering
+# CONFIG_FS_WRITEBUFFER
+#   Enable write buffering
+#
+CONFIG_FS_READAHEAD=n
+CONFIG_FS_WRITEBUFFER=n
+
+#
+# SDIO-based MMC/SD driver
+#
+# CONFIG_SDIO_DMA
+#   SDIO driver supports DMA
+# CONFIG_MMCSD_MMCSUPPORT
+#   Enable support for MMC cards
+# CONFIG_MMCSD_HAVECARDDETECT
+#   SDIO driver card detection is 100% accurate
+#
+CONFIG_SDIO_DMA=n
+CONFIG_MMCSD_MMCSUPPORT=n
+CONFIG_MMCSD_HAVECARDDETECT=n
+
+#
+# TCP/IP and UDP support via uIP
+# CONFIG_NET - Enable or disable all network features
+# CONFIG_NET_NOINTS - uIP not called from interrupt level.
+# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no)
+# CONFIG_NET_IPv6 - Build in support for IPv6
+# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
+# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
+# CONFIG_NET_BUFSIZE - uIP buffer size
+# CONFIG_NET_TCP - TCP support on or off
+# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
+# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
+# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
+# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
+#   accept() is called. The size of the backlog is selected when listen() is called.
+# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
+# CONFIG_NET_UDP - UDP support on or off
+# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
+# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
+# CONFIG_NET_ICMP - ICMP ping response support on or off
+# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
+# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
+# CONFIG_NET_STATISTICS - uIP statistics on or off
+# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
+# CONFIG_NET_BROADCAST - Broadcast support
+# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
+# CONFIG_NET_ARP_IPIN - Harvest IP/MAC address mappings from the ARP table
+#   from incoming IP packets.
+# CONFIG_NET_MULTICAST - Outgoing multi-cast address support
+# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when
+#   looking for duplicates
+#
+CONFIG_NET=n
+CONFIG_NET_NOINTS=n
+CONFIG_NET_MULTIBUFFER=y
+CONFIG_NET_IPv6=n
+CONFIG_NSOCKET_DESCRIPTORS=0
+CONFIG_NET_SOCKOPTS=y
+CONFIG_NET_BUFSIZE=562
+CONFIG_NET_TCP=n
+CONFIG_NET_TCP_CONNS=40
+CONFIG_NET_MAX_LISTENPORTS=40
+CONFIG_NET_UDP=n
+CONFIG_NET_UDP_CHECKSUMS=y
+#CONFIG_NET_UDP_CONNS=10
+CONFIG_NET_ICMP=n
+CONFIG_NET_ICMP_PING=n
+#CONFIG_NET_PINGADDRCONF=0
+CONFIG_NET_STATISTICS=y
+#CONFIG_NET_RECEIVE_WINDOW=
+CONFIG_NET_BROADCAST=n
+#CONFIG_NET_ARPTAB_SIZE=8
+CONFIG_NET_ARP_IPIN=n
+CONFIG_NET_MULTICAST=n
+#CONFIG_NET_FWCACHE_SIZE=2
+
+#
+# UIP Network Utilities
+# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
+# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
+#
+CONFIG_NET_DHCP_LIGHT=n
+CONFIG_NET_RESOLV_ENTRIES=4
+
+#
+# RTC Configuration
+#
+# CONFIG_RTC - Enables general support for a hardware RTC.  Specific
+#   architectures may require other specific settings.
+# CONFIG_RTC_DATETIME - There are two general types of RTC:  (1) A simple
+#   battery backed counter that keeps the time when power is down, and (2)
+#    A full date / time RTC the provides the date and time information, often
+#   in BCD format.  If CONFIG_RTC_DATETIME is selected, it specifies this
+#   second kind of RTC. In this case, the RTC is used to "seed" the normal
+#   NuttX timer and the NuttX system timer provides for higher resoution
+#   time.
+# CONFIG_RTC_HIRES - If CONFIG_RTC_DATETIME not selected, then the simple,
+#   battery backed counter is used.  There are two different implementations
+#   of such simple counters based on the time resolution of the counter:
+#   The typical RTC keeps time to resolution of 1 second, usually
+#   supporting a 32-bit time_t value.  In this case, the RTC is used to
+#   "seed" the normal NuttX timer and the NuttX timer provides for higher
+#   resoution time. If CONFIG_RTC_HIRES is enabled in the NuttX configuration,
+#   then the RTC provides higher resolution time and completely replaces the
+#   system timer for purpose of date and time.
+# CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the frequency
+#  of the high resolution RTC must be provided.  If CONFIG_RTC_HIRES is
+#   not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
+# CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an
+#  alarm.  A callback function will be executed when the alarm goes off
+#
+CONFIG_RTC=n
+CONFIG_RTC_DATETIME=y
+CONFIG_RTC_HIRES=n
+CONFIG_RTC_FREQUENCY=n
+CONFIG_RTC_ALARM=n
+
+#
+# USB Device Configuration
+#
+# CONFIG_USBDEV
+#   Enables USB device support
+# CONFIG_USBDEV_ISOCHRONOUS
+#   Build in extra support for isochronous endpoints
+# CONFIG_USBDEV_DUALSPEED
+#   Hardware handles high and full speed operation (USB 2.0)
+# CONFIG_USBDEV_SELFPOWERED
+#   Will cause USB features to indicate that the device is
+#   self-powered
+# CONFIG_USBDEV_MAXPOWER
+#   Maximum power consumption in mA
+# CONFIG_USBDEV_TRACE
+#   Enables USB tracing for debug
+# CONFIG_USBDEV_TRACE_NRECORDS
+#   Number of trace entries to remember
+#
+CONFIG_USBDEV=n
+CONFIG_USBDEV_ISOCHRONOUS=n
+CONFIG_USBDEV_DUALSPEED=n
+CONFIG_USBDEV_SELFPOWERED=y
+CONFIG_USBDEV_REMOTEWAKEUP=n
+CONFIG_USBDEV_MAXPOWER=100
+CONFIG_USBDEV_TRACE=n
+CONFIG_USBDEV_TRACE_NRECORDS=128
+
+#
+# USB Serial Device Configuration
+#
+# CONFIG_USBSER
+#   Enable compilation of the USB serial driver
+# CONFIG_USBSER_EPINTIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   interrupt IN operation
+# CONFIG_USBSER_EPBULKOUT
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk OUT operation
+# CONFIG_USBSER_EPBULKIN
+#   The logical 7-bit address of a hardware endpoint that supports
+#   bulk IN operation
+# # CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
+#   Size of the serial receive/transmit buffers
+#
+CONFIG_USBSER=n
+CONFIG_USBSER_EPINTIN=1
+CONFIG_USBSER_EPBULKOUT=2
+CONFIG_USBSER_EPBULKIN=3
+CONFIG_USBSER_NWRREQS=4
+CONFIG_USBSER_NRDREQS=4
+CONFIG_USBSER_VENDORID=0x067b
+CONFIG_USBSER_PRODUCTID=0x2303
+CONFIG_USBSER_VENDORSTR="Nuttx"
+CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
+CONFIG_USBSER_RXBUFSIZE=512
+CONFIG_USBSER_TXBUFSIZE=512
+
+#
+# USB Storage Device Configuration
+#
+# CONFIG_USBSTRG
+#   Enable compilation of the USB storage driver
+# CONFIG_USBSTRG_EP0MAXPACKET
+#   Max packet size for endpoint 0
+# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
+#   The logical 7-bit address of a hardware endpoints that support
+#   bulk OUT and IN operations
+# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
+#   The number of write/read requests that can be in flight
+# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
+#   The size of the buffer in each write/read request.  This
+#   value needs to be at least as large as the endpoint
+#   maxpacket and ideally as large as a block device sector.
+# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
+#   The vendor ID code/string
+# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
+#   The product ID code/string
+# CONFIG_USBSTRG_REMOVABLE
+#   Select if the media is removable
+#
+CONFIG_USBSTRG=n
+CONFIG_USBSTRG_EP0MAXPACKET=64
+CONFIG_USBSTRG_EPBULKOUT=2
+CONFIG_USBSTRG_EPBULKIN=5
+CONFIG_USBSTRG_NRDREQS=2
+CONFIG_USBSTRG_NWRREQS=2
+CONFIG_USBSTRG_BULKINREQLEN=256
+CONFIG_USBSTRG_BULKOUTREQLEN=256
+CONFIG_USBSTRG_VENDORID=0x584e
+CONFIG_USBSTRG_VENDORSTR="NuttX"
+CONFIG_USBSTRG_PRODUCTID=0x5342
+CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
+CONFIG_USBSTRG_VERSIONNO=0x0399
+CONFIG_USBSTRG_REMOVABLE=y
+
+#
+# Graphics related configuration settings
+#
+# CONFIG_NX
+#   Enables overall support for graphics library and NX
+# CONFIG_NX_MULTIUSER
+#   Configures NX in multi-user mode
+# CONFIG_NX_NPLANES
+#   Some YUV color formats requires support for multiple planes,
+#   one for each color component.  Unless you have such special
+#   hardware, this value should be undefined or set to 1
+# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
+# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
+# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
+# CONFIG_NX_DISABLE_32BPP
+#   NX supports a variety of pixel depths.  You can save some
+#   memory by disabling support for unused color depths.
+# CONFIG_NX_PACKEDMSFIRST
+#   If a pixel depth of less than 8-bits is used, then NX needs
+#   to know if the pixels pack from the MS to LS or from LS to MS
+# CONFIG_NX_LCDDRIVER
+#   By default, NX builds to use a framebuffer driver (see
+#   include/nuttx/fb.h). If this option is defined, NX will
+#   build to use an LCD driver (see include/nuttx/lcd/lcd.h).
+# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
+# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
+# CONFIG_NX_MOUSE
+#   Build in support for mouse input
+# CONFIG_NX_KBD
+#   Build in support of keypad/keyboard input
+# CONFIG_NXTK_BORDERWIDTH
+#   Specifies with with of the border (in pixels) used with
+#   framed windows.  The default is 4.
+# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
+#   Specify the colors of the border used with framed windows.
+#   CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
+#   is normally darker.  The default is medium and dark grey,
+#   respectively
+# CONFIG_NXTK_AUTORAISE
+#   If set, a window will be raised to the top if the mouse position
+#   is over a visible portion of the window.  Default: A mouse
+#   button must be clicked over a visible portion of the window.
+# CONFIG_NXFONTS_CHARBITS
+#   The number of bits in the character set.  Current options are
+#   only 7 and 8.  The default is 7.
+# CONFIG_NXFONT_SANS17X22
+#  This option enables support for a tiny, 17x22 san serif font
+#  (font ID FONTID_SANS17X22 == 14).
+# CONFIG_NXFONT_SANS20X26
+#  This option enables support for a tiny, 20x26 san serif font
+#  (font ID FONTID_SANS20X26 == 15).
+# CONFIG_NXFONT_SANS23X27
+#   This option enables support for a tiny, 23x27 san serif font
+#   (font ID FONTID_SANS23X27 == 1).
+# CONFIG_NXFONT_SANS22X29
+#   This option enables support for a small, 22x29 san serif font
+#   (font ID FONTID_SANS22X29 == 2).
+# CONFIG_NXFONT_SANS28X37
+#   This option enables support for a medium, 28x37 san serif font
+#   (font ID FONTID_SANS28X37 == 3).
+# CONFIG_NXFONT_SANS39X48
+#   This option enables support for a large, 39x48 san serif font
+#   (font ID FONTID_SANS39X48 == 4).
+# CONFIG_NXFONT_SANS17X23B
+#   This option enables support for a tiny, 17x23 san serif bold font
+#   (font ID FONTID_SANS17X23B == 16).
+# CONFIG_NXFONT_SANS20X27B
+#   This option enables support for a tiny, 20x27 san serif bold font
+#   (font ID FONTID_SANS20X27B == 17).
+# CONFIG_NXFONT_SANS22X29B
+#   This option enables support for a small, 22x29 san serif bold font
+#   (font ID FONTID_SANS22X29B == 5).
+# CONFIG_NXFONT_SANS28X37B
+#   This option enables support for a medium, 28x37 san serif bold font
+#   (font ID FONTID_SANS28X37B == 6).
+# CONFIG_NXFONT_SANS40X49B
+#   This option enables support for a large, 40x49 san serif bold font
+#   (font ID FONTID_SANS40X49B == 7).
+# CONFIG_NXFONT_SERIF22X29
+#   This option enables support for a small, 22x29 font (with serifs)
+#   (font ID FONTID_SERIF22X29 == 8).
+# CONFIG_NXFONT_SERIF29X37
+#   This option enables support for a medium, 29x37 font (with serifs)
+#   (font ID FONTID_SERIF29X37 == 9).
+# CONFIG_NXFONT_SERIF38X48
+#   This option enables support for a large, 38x48 font (with serifs)
+#   (font ID FONTID_SERIF38X48 == 10).
+# CONFIG_NXFONT_SERIF22X28B
+#   This option enables support for a small, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF22X28B == 11).
+# CONFIG_NXFONT_SERIF27X38B
+#   This option enables support for a medium, 27x38 bold font (with serifs)
+#   (font ID FONTID_SERIF27X38B == 12).
+# CONFIG_NXFONT_SERIF38X49B
+#   This option enables support for a large, 38x49 bold font (with serifs)
+#   (font ID FONTID_SERIF38X49B == 13).
+#
+# NX Multi-user only options:
+#
+# CONFIG_NX_BLOCKING
+#   Open the client message queues in blocking mode.  In this case,
+#   nx_eventhandler()  will not return until a message is received and processed.
+# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
+#   Specifies the maximum number of messages that can fit in
+#   the message queues.  No additional resources are allocated, but
+#   this can be set to prevent flooding of the client or server with
+#   too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
+#   messages are pre-allocated).
+#
+CONFIG_NX=n
+CONFIG_NX_MULTIUSER=n
+CONFIG_NX_NPLANES=1
+CONFIG_NX_DISABLE_1BPP=y
+CONFIG_NX_DISABLE_2BPP=y
+CONFIG_NX_DISABLE_4BPP=y
+CONFIG_NX_DISABLE_8BPP=y
+CONFIG_NX_DISABLE_16BPP=n
+CONFIG_NX_DISABLE_24BPP=y
+CONFIG_NX_DISABLE_32BPP=y
+CONFIG_NX_PACKEDMSFIRST=n
+CONFIG_NX_LCDDRIVER=y
+CONFIG_LCD_MAXPOWER=1
+CONFIG_LCD_MAXCONTRAST=1
+CONFIG_NX_MOUSE=y
+CONFIG_NX_KBD=y
+#CONFIG_NXTK_BORDERWIDTH=4
+CONFIG_NXTK_BORDERCOLOR1=0xd69a
+CONFIG_NXTK_BORDERCOLOR2=0xad55
+CONFIG_NXTK_AUTORAISE=n
+CONFIG_NXFONT_SANS17X22=y
+CONFIG_NXFONT_SANS20X26=n
+CONFIG_NXFONT_SANS22X29=n
+CONFIG_NXFONT_SANS23X27=n
+CONFIG_NXFONT_SANS28X37=n
+CONFIG_NXFONT_SANS17X23B=n
+CONFIG_NXFONT_SANS20X27B=y
+CONFIG_NXFONT_SANS22X29B=y
+CONFIG_NXFONT_SANS28X37B=n
+CONFIG_NXFONT_SANS40X49B=n
+CONFIG_NXFONT_SERIF22X29=n
+CONFIG_NXFONT_SERIF29X37=n
+CONFIG_NXFONT_SERIF38X48=n
+CONFIG_NXFONT_SERIF22X28B=n
+CONFIG_NXFONT_SERIF27X38B=n
+CONFIG_NXFONT_SERIF38X49B=n
+CONFIG_NXFONTS_CHARBITS=7
+CONFIG_NX_BLOCKING=y
+CONFIG_NX_MXSERVERMSGS=32
+CONFIG_NX_MXCLIENTMSGS=16
+
+#
+# NxWidgets
+CONFIG_NXWIDGETS_BPP=16
+CONFIG_NXWIDGETS_DEFAULT_FONTID=5
+
+#
+# stm32f4discovery LCD Hardware Configuration
+#
+# CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
+#   support. Default is this 320x240 "landscape" orientation
+#   (this setting is informative only... not used).
+# CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
+#   orientation support.  In this orientation, the PT3's
+#   LCD ribbon cable is at the bottom of the display. Default is
+#   320x240 "landscape" orientation.
+# CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
+#   portrait" orientation support.  In this orientation, the
+#   stm32f4discovery's LCD ribbon cable is at the top of the display.
+#   Default is 320x240 "landscape" orientation.
+# CONFIG_LCD_BACKLIGHT - Define to support a backlight.
+# CONFIG_LCD_PWM - If CONFIG_STM32_TIM1 is also defined, then an
+#   adjustable backlight will be provided using timer 1 to generate
+#   various pulse widthes.  The granularity of the settings is
+#   determined by CONFIG_LCD_MAXPOWER.  If CONFIG_LCD_PWM (or
+#   CONFIG_STM32_TIM1) is not defined, then a simple on/off backlight
+#   is provided.
+#
+CONFIG_LCD_LANDSCAPE=n
+CONFIG_LCD_PORTRAIT=n
+CONFIG_LCD_RPORTRAIT=y
+CONFIG_LCD_BACKLIGHT=y
+CONFIG_LCD_PWM=n
+CONFIG_STM32_AM240320_DISABLE=y
+CONFIG_STM32_SPFD5408B_DISABLE=n
+CONFIG_STM32_R61580_DISABLE=n
+
+#
+# Settings for examples/uip
+#
+CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_UIP_DHCPC=n
+
+#
+# Settings for examples/nettest
+CONFIG_EXAMPLE_NETTEST_SERVER=n
+CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
+CONFIG_EXAMPLE_NETTEST_NOMAC=y
+CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
+
+#
+# Settings for examples/ostest
+#
+CONFIG_EXAMPLES_OSTEST_LOOPS=1
+CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
+CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
+
+#
+# Settings for apps/nshlib
+#
+# CONFIG_NSH_BUILTIN_APPS - Support external registered,
+#   "named" applications that can be executed from the NSH
+#   command line (see apps/README.txt for more information).
+# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
+# CONFIG_NSH_STRERROR - Use strerror(errno)
+# CONFIG_NSH_LINELEN - Maximum length of one command line
+# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
+# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
+# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
+# CONFIG_NSH_DISABLEBG - Disable background commands
+# CONFIG_NSH_ROMFSETC - Use startup script in /etc
+# CONFIG_NSH_CONSOLE - Use serial console front end
+# CONFIG_NSH_CONDEV - Select the serial device used to support
+#   the NSH console.  Default: stdin and stdout
+# CONFIG_NSH_TELNET - Use telnetd console front end
+# CONFIG_NSH_ARCHINIT - Platform provides architecture
+#   specific initialization (nsh_archinitialize()).
+#
+# If CONFIG_NSH_TELNET is selected:
+# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
+# CONFIG_NSH_DHCPC - Obtain address using DHCP
+# CONFIG_NSH_IPADDR - Provides static IP address
+# CONFIG_NSH_DRIPADDR - Provides static router IP address
+# CONFIG_NSH_NETMASK - Provides static network mask
+# CONFIG_NSH_NOMAC - Use a bogus MAC address
+#
+# If CONFIG_NSH_ROMFSETC is selected:
+# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
+# CONFIG_NSH_INITSCRIPT - Relative path to init script
+# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
+# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
+# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
+# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
+# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
+# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
+#
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_STRERROR=n
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_STACKSIZE=2048
+CONFIG_NSH_NESTDEPTH=3
+CONFIG_NSH_DISABLESCRIPT=n
+CONFIG_NSH_DISABLEBG=n
+CONFIG_NSH_ROMFSETC=n
+CONFIG_NSH_CONSOLE=y
+#CONFIG_NSH_CONDEV="/dev/ttyS1"
+CONFIG_NSH_TELNET=n
+CONFIG_NSH_ARCHINIT=n
+CONFIG_NSH_IOBUFFER_SIZE=512
+CONFIG_NSH_DHCPC=n
+CONFIG_NSH_NOMAC=y
+CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
+CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
+CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
+CONFIG_NSH_ROMFSMOUNTPT="/etc"
+CONFIG_NSH_INITSCRIPT="init.d/rcS"
+CONFIG_NSH_ROMFSDEVNO=0
+CONFIG_NSH_ROMFSSECTSIZE=64
+CONFIG_NSH_FATDEVNO=1
+CONFIG_NSH_FATSECTSIZE=512
+CONFIG_NSH_FATNSECTORS=1024
+CONFIG_NSH_FATMOUNTPT=/tmp
+
+#
+# Architecture-specific NSH options
+#
+CONFIG_NSH_MMCSDSPIPORTNO=0
+CONFIG_NSH_MMCSDSLOTNO=0
+CONFIG_NSH_MMCSDMINOR=0
+
+#
+# Settings for examples/nx
+#
+# CONFIG_EXAMPLES_NX_BUILTIN -- Build the NX example as a "built-in"
+#  that can be executed from the NSH command line  
+# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NX_DEVNO - The LCD device to select from the LCD
+#  driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background.  Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
+#   CONFIG_EXAMPLES_NX_BPP.
+# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows;  Default is to
+#   use pretty, framed NXTK windows with toolbars.
+# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
+#   the NX server.  Default 2048
+# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority.  Default: 80
+# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority.  Default: 120
+# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
+#   nx_eventnotify().  Default: 4
+#
+CONFIG_EXAMPLES_NX_BUILTIN=n
+CONFIG_EXAMPLES_NX_VPLANE=0
+CONFIG_EXAMPLES_NX_DEVNO=0
+CONFIG_EXAMPLES_NX_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NX_COLOR1=0xaedc
+CONFIG_EXAMPLES_NX_COLOR2=0xe7ff
+CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a
+CONFIG_EXAMPLES_NX_FONTID=0
+CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
+CONFIG_EXAMPLES_NX_BPP=16
+CONFIG_EXAMPLES_NX_RAWWINDOWS=n
+CONFIG_EXAMPLES_NX_STACKSIZE=2048
+CONFIG_EXAMPLES_NX_CLIENTPRIO=80
+CONFIG_EXAMPLES_NX_SERVERPRIO=120
+CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
+CONFIG_EXAMPLES_NX_EXTERNINIT=n
+
+#
+# Settings for examples/nxhello
+#
+# CONFIG_EXAMPLES_NXHELLO_BUILTIN -- Build the NXHELLO example as a "built-in"
+#   that can be executed from the NSH command line    
+# CONFIG_EXAMPLES_NXHELLO_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXHELLO_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXHELLO_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXHELLO_BPP.
+# CONFIG_EXAMPLES_NXHELLO_FONTID - Selects the font (see font ID numbers in
+#   include/nuttx/nx/nxfonts.h)
+# CONFIG_EXAMPLES_NXHELLO_FONTCOLOR -- The color of the fonts used in the
+#   background window. Default depends on CONFIG_EXAMPLES_NXHELLO_BPP.
+# CONFIG_EXAMPLES_NXHELLO_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 32.
+# CONFIG_EXAMPLES_NXHELLO_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXHELLO_BUILTIN=n
+CONFIG_EXAMPLES_NXHELLO_VPLANE=0
+CONFIG_EXAMPLES_NXHELLO_DEVNO=0
+CONFIG_EXAMPLES_NXHELLO_BGCOLOR=0x0011
+CONFIG_EXAMPLES_NXHELLO_FONTID=6
+CONFIG_EXAMPLES_NXHELLO_FONTCOLOR=0xffdf
+CONFIG_EXAMPLES_NXHELLO_BPP=16
+CONFIG_EXAMPLES_NXHELLO_EXTERNINIT=n
+
+#
+# Settings for examples/nximage
+#
+# CONFIG_EXAMPLES_NXIMAGE_BUILTIN -- Build the NXIMAGE example as a "built-in"
+#   that can be executed from the NSH command line    
+# CONFIG_EXAMPLES_NXIMAGE_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXIMAGE_BPP -- Pixels per pixel to use.  Valid options
+#   include 8, 16, and 24.  Default is 16.
+# CONFIG_EXAMPLES_NXIMAGE_XSCALEp5, CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0 -- The logo image width is 160 columns.
+#   One of these may be defined to rescale the image horizontally by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_YSCALEp5, CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5,
+# CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0 -- The logo image height is 160 rows.
+#   One of these may be defined to rescale the image vertically by .5, 1.5,
+#   or 2.0.
+# CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXIMAGE_BUILTIN=n
+CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
+CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
+CONFIG_EXAMPLES_NXIMAGE_BPP=16
+CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
+CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
+CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
+CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
+
+#
+# Settings for examples/nxlines
+#
+# CONFIG_EXAMPLES_NXLINES_BUILTIN -- Build the NXLINES example as a "built-in"
+#   that can be executed from the NSH command line
+# CONFIG_EXAMPLES_NXLINES_VPLANE -- The plane to select from the frame-
+#   buffer driver for use in the test.  Default: 0
+# CONFIG_EXAMPLES_NXLINES_DEVNO - The LCD device to select from the LCD
+#   driver for use in the test: Default: 0
+# CONFIG_EXAMPLES_NXLINES_BGCOLOR -- The color of the background.  Default
+#   depends on CONFIG_EXAMPLES_NXLINES_BPP.
+# CONFIG_EXAMPLES_NXLINES_LINEWIDTH - Selects the width of the lines in
+#   pixels (default: 16)
+# CONFIG_EXAMPLES_NXLINES_LINECOLOR -- The color of the central lines drawn
+#   in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BORDERWIDTH -- The width of the circular border
+#   drawn in the background window. (default: 4).
+# CONFIG_EXAMPLES_NXLINES_BORDERCOLOR -- The color of the circular border
+#   drawn in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR -- The color of the circular region
+#   filled in the background window. Default depends on CONFIG_EXAMPLES_NXLINES_BPP
+#   (there really is no meaningful default).
+# CONFIG_EXAMPLES_NXLINES_BPP -- Pixels per pixel to use.  Valid options
+#   include 2, 4, 8, 16, 24, and 32.  Default is 16.
+# CONFIG_EXAMPLES_NXLINES_EXTERNINIT - The driver for the graphics device on
+#   this platform requires some unusual initialization.  This is the
+#   for, for example, SPI LCD/OLED devices.  If this configuration is
+#   selected, then the platform code must provide an LCD initialization
+#   function.
+#
+CONFIG_EXAMPLES_NXLINES_BUILTIN=n
+CONFIG_EXAMPLES_NXLINES_VPLANE=0
+CONFIG_EXAMPLES_NXLINES_DEVNO=0
+CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
+CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
+CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
+CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
+CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
+CONFIG_EXAMPLES_NXLINES_BPP=16
+CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
+
+#
+# Settings for examples/touchscreen
+#
+# CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN - Build the touchscreen test as
+#   an NSH built-in function.  Default: Built as a standalone problem
+# CONFIG_EXAMPLES_TOUCHSCREEN_MINOR - The minor device number.  Minor=N
+#   correspnds to touchscreen device /dev/input0.  Note this value must
+#   with CONFIG_EXAMPLES_TOUCHSCREEN_DEVPATH.  Default 0.
+# CONFIG_EXAMPLES_TOUCHSCREEN_DEVPATH - The path to the touchscreen
+#   device.  This must be consistent with CONFIG_EXAMPLES_TOUCHSCREEN_MINOR.
+#   Default: "/dev/input0"
+# CONFIG_EXAMPLES_TOUCHSCREEN_NSAMPLES - If CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN
+#   is defined, then the number of samples is provided on the command line
+#   and this value is ignored.  Otherwise, this number of samples is
+#   collected and the program terminates.  Default:  Samples are collected
+#   indefinitely.
+#
+CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN=n
+CONFIG_EXAMPLES_TOUCHSCREEN_MINOR=0
+CONFIG_EXAMPLES_TOUCHSCREEN_DEVPATH="/dev/input0"
+CONFIG_EXAMPLES_TOUCHSCREEN_NSAMPLES=25
+
+#
+# Settings for examples/buttons
+#
+# CONFIG_EXAMPLE_BUTTONS_MIN and CONFIG_EXAMPLE_BUTTONS_MAX
+#   Lowest and highest button number (0-7)
+# CONFIG_EXAMPLE_IRQBUTTONS_MIN and CONFIG_EXAMPLE_IRQBUTTONS_MAX
+#   Lowest and highest interrupting button number (-7)
+# CONFIG_EXAMPLE_BUTTONS_NAMEn - Name for button n
+#
+CONFIG_EXAMPLE_BUTTONS_MIN=0
+CONFIG_EXAMPLE_BUTTONS_MAX=2
+CONFIG_EXAMPLE_IRQBUTTONS_MIN=0
+CONFIG_EXAMPLE_IRQBUTTONS_MAX=2
+CONFIG_EXAMPLE_BUTTONS_NAME0="Key/Select"
+CONFIG_EXAMPLE_BUTTONS_NAME1="Left/Right"
+CONFIG_EXAMPLE_BUTTONS_NAME2="Up/Down"
+
+#
+# Settings for examples/usbserial
+#
+# CONFIG_EXAMPLES_USBSERIAL_INONLY
+#    Only verify IN (device-to-host) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
+#    Only verify OUT (host-to-device) data transfers.  Default: both
+# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
+#    Send only small, single packet messages.  Default: Send large and small.
+# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
+#    Send only large, multi-packet messages.  Default: Send large and small.
+#
+CONFIG_EXAMPLES_USBSERIAL_INONLY=n
+CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
+CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
+
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
+
+#
+# Settings for examples/usbstorage
+#
+# CONFIG_EXAMPLES_USBSTRG_BUILTIN
+#   This example can be built as two NSH "built-in" commands if this option
+#   is selection: 'msconn' will connect the USB mass storage device; 'msdis'
+#   will disconnect the USB storage device.
+# CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    Defines the number of logical units (LUNs) exported by the USB storage
+#    driver.  Each LUN corresponds to one exported block driver (or partition
+#    of a block driver).  May be 1, 2, or 3.  Default is 1.
+# CONFIG_EXAMPLES_USBSTRG_DEVMINOR1
+#    The minor device number of the block driver for the first LUN. For
+#    example, N in /dev/mmcsdN.  Used for registering the block driver. Default
+#    is zero.
+# CONFIG_EXAMPLES_USBSTRG_DEVPATH1
+#    The full path to the registered block driver.  Default is "/dev/mmcsd0"
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR2 and CONFIG_EXAMPLES_USBSTRG_DEVPATH2
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 2 or 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEVMINOR3 and CONFIG_EXAMPLES_USBSTRG_DEVPATH3
+#    Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBSTRG_NLUNS
+#    is 3.  No defaults.
+#  CONFIG_EXAMPLES_USBSTRG_DEBUGMM
+#    Enables some debug tests to check for memory usage and memory leaks.
+#
+#  If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then
+#  the example code will also manage the USB trace output.  The amount of trace output
+#  can be controlled using:
+#
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINIT
+#    Show initialization events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECLASS
+#    Show class driver events
+#  CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS
+#    Show data transfer events
+#  CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER
+#    Show controller events
+#  CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS
+#    Show interrupt-related events.
+#
+CONFIG_EXAMPLES_USBSTRG_BUILTIN=n
+CONFIG_EXAMPLES_USBSTRG_NLUNS=1
+CONFIG_EXAMPLES_USBSTRG_DEVMINOR1=0
+CONFIG_EXAMPLES_USBSTRG_DEVPATH1="/dev/mmcsd0"
+CONFIG_EXAMPLES_USBSTRG_DEBUGMM=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINIT=n
+CONFIG_EXAMPLES_USBSTRG_TRACECLASS=n
+CONFIG_EXAMPLES_USBSTRG_TRACETRANSFERS=n
+CONFIG_EXAMPLES_USBSTRG_TRACECONTROLLER=n
+CONFIG_EXAMPLES_USBSTRG_TRACEINTERRUPTS=n
+
+#
+# Stack and heap information
+#
+# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
+#   operation from FLASH but must copy initialized .data sections to RAM.
+#   (should also be =n for the stm32f4discovery which always runs from flash)
+# CONFIG_BOOT_COPYTORAM -  Some configurations boot in FLASH
+#   but copy themselves entirely into RAM for better performance.
+# CONFIG_CUSTOM_STACK - The up_ implementation will handle
+#   all stack operations outside of the nuttx model.
+# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
+# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
+#  This is the thread that (1) performs the inital boot of the system up
+#  to the point where user_start() is spawned, and (2) there after is the
+#  IDLE thread that executes only when there is no other thread ready to
+#  run.
+# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
+#  for the main user thread that begins at the user_start() entry point.
+# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
+# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
+# CONFIG_HEAP_BASE - The beginning of the heap
+# CONFIG_HEAP_SIZE - The size of the heap
+#
+CONFIG_BOOT_RUNFROMFLASH=n
+CONFIG_BOOT_COPYTORAM=n
+CONFIG_CUSTOM_STACK=n
+CONFIG_STACK_POINTER=
+CONFIG_IDLETHREAD_STACKSIZE=1024
+CONFIG_USERMAIN_STACKSIZE=2048
+CONFIG_PTHREAD_STACK_MIN=256
+CONFIG_PTHREAD_STACK_DEFAULT=2048
+CONFIG_HEAP_BASE=
+CONFIG_HEAP_SIZE=
diff --git a/nuttx/configs/stm32f4discovery/ostest/ld.script b/nuttx/configs/stm32f4discovery/ostest/ld.script
new file mode 100755
index 000000000..fbdfe21c7
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/ostest/ld.script
@@ -0,0 +1,116 @@
+/****************************************************************************
+ * configs/stm32f4discovery/ostest/ld.script
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The STM32F407VG has 1024Kb of FLASH beginning at address 0x0800:0000 and
+ * 192Kb of SRAM. SRAM is split up into three blocks:
+ *
+ * 1) 112Kb of SRAM beginning at address 0x2000:0000
+ * 2)  16Kb of SRAM beginning at address 0x2001:c000
+ * 3)  64Kb of TCM SRAM beginning at address 0x1000:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address
+ * range.
+ */
+
+MEMORY
+{
+    flash (rx) : ORIGIN = 0x08000000, LENGTH = 1024K
+    sram (rwx) : ORIGIN = 0x20000000, LENGTH = 112K
+}
+
+OUTPUT_ARCH(arm)
+ENTRY(_stext)
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		*(.text .text.*)        
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)        
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} >sram
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
diff --git a/nuttx/configs/stm32f4discovery/ostest/setenv.sh b/nuttx/configs/stm32f4discovery/ostest/setenv.sh
new file mode 100755
index 000000000..58c639e16
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/ostest/setenv.sh
@@ -0,0 +1,67 @@
+#!/bin/bash
+# configs/stm32f4discovery/ostest/setenv.sh
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This the Cygwin path to the location where I installed the RIDE
+# toolchain under windows.  You will also have to edit this if you install
+# the RIDE toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin"
+
+# This the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This the Cygwin path to the location where I build the buildroot
+# toolchain.
+#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"
diff --git a/nuttx/configs/stm32f4discovery/src/Makefile b/nuttx/configs/stm32f4discovery/src/Makefile
new file mode 100644
index 000000000..133cc1467
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/Makefile
@@ -0,0 +1,99 @@
+############################################################################
+# configs/stm32f4discovery/src/Makefile
+#
+#   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+-include $(TOPDIR)/Make.defs
+
+CFLAGS		+= -I$(TOPDIR)/sched
+
+ASRCS		= 
+AOBJS		= $(ASRCS:.S=$(OBJEXT))
+
+CSRCS		= up_boot.c up_spi.c
+
+ifeq ($(CONFIG_ARCH_LEDS),y)
+CSRCS		+= up_autoleds.c
+else
+CSRCS		+= up_userleds.c
+endif
+
+ifeq ($(CONFIG_ARCH_BUTTONS),y)
+CSRCS		+=  up_buttons.c
+endif
+
+ifeq ($(CONFIG_PWM),y)
+CSRCS		+= up_pwm.c
+endif
+
+COBJS		= $(CSRCS:.c=$(OBJEXT))
+
+SRCS		= $(ASRCS) $(CSRCS)
+OBJS		= $(AOBJS) $(COBJS)
+
+ARCH_SRCDIR	= $(TOPDIR)/arch/$(CONFIG_ARCH)/src
+ifeq ($(WINTOOL),y)
+  CFLAGS	+= -I "${shell cygpath -w $(ARCH_SRCDIR)/chip}" \
+  		   -I "${shell cygpath -w $(ARCH_SRCDIR)/common}" \
+  		   -I "${shell cygpath -w $(ARCH_SRCDIR)/armv7-m}"
+else
+  CFLAGS	+= -I$(ARCH_SRCDIR)/chip -I$(ARCH_SRCDIR)/common -I$(ARCH_SRCDIR)/armv7-m
+endif
+
+all: libboard$(LIBEXT)
+
+$(AOBJS): %$(OBJEXT): %.S
+	$(call ASSEMBLE, $<, $@)
+
+$(COBJS) $(LINKOBJS): %$(OBJEXT): %.c
+	$(call COMPILE, $<, $@)
+
+libboard$(LIBEXT): $(OBJS)
+	@( for obj in $(OBJS) ; do \
+		$(call ARCHIVE, $@, $${obj}); \
+	done ; )
+
+.depend: Makefile $(SRCS)
+	@$(MKDEP) $(CC) -- $(CFLAGS) -- $(SRCS) >Make.dep
+	@touch $@
+
+depend: .depend
+
+clean:
+	@rm -f libboard$(LIBEXT) *~ .*.swp
+	$(call CLEAN)
+
+distclean: clean
+	@rm -f Make.dep .depend
+
+-include Make.dep
diff --git a/nuttx/configs/stm32f4discovery/src/stm32f4discovery-internal.h b/nuttx/configs/stm32f4discovery/src/stm32f4discovery-internal.h
new file mode 100644
index 000000000..8b9ca8d3c
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/stm32f4discovery-internal.h
@@ -0,0 +1,125 @@
+/****************************************************************************************************
+ * configs/stm3240g_eval/src/stm3240g_internal.h
+ * arch/arm/src/board/stm3240g_internal.n
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************************************/
+
+#ifndef __CONFIGS_STM3240G_EVAL_SRC_STM3240G_INTERNAL_H
+#define __CONFIGS_STM3240G_EVAL_SRC_STM3240G_INTERNAL_H
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <nuttx/config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+/* Configuration ************************************************************************************/
+/* How many SPI modules does this chip support? */
+
+#if STM32_NSPI < 1
+#  undef CONFIG_STM32_SPI1
+#  undef CONFIG_STM32_SPI2
+#  undef CONFIG_STM32_SPI3
+#elif STM32_NSPI < 2
+#  undef CONFIG_STM32_SPI2
+#  undef CONFIG_STM32_SPI3
+#elif STM32_NSPI < 3
+#  undef CONFIG_STM32_SPI3
+#endif
+
+/* STM32F4 Discovery GPIOs **************************************************************************/
+/* LEDs */
+
+#define GPIO_LED1       (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN12)
+#define GPIO_LED2       (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13)
+#define GPIO_LED3       (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14)
+#define GPIO_LED4       (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
+                         GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN15)
+
+/* BUTTONS -- NOTE that all have EXTI interrupts configured */
+
+#define MIN_IRQBUTTON   BUTTON_USER
+#define MAX_IRQBUTTON   BUTTON_USER
+#define NUM_IRQBUTTONS  1
+
+#define GPIO_BTN_USER   (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTA|GPIO_PIN0)
+
+/* PWM
+ *
+ * The STM32F4 Discovery has no real on-board PWM devices, but the board can be
+ * configured to output a pulse train using TIM4 CH2 on PD13.
+ */
+
+#define STM3240G_EVAL_PWMTIMER   4
+#define STM3240G_EVAL_PWMCHANNEL 2
+
+/* SPI chip selects */
+
+#define GPIO_CS_MEMS	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
+                         GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the stm32f4discovery board.
+ *
+ ****************************************************************************************************/
+
+extern void weak_function stm32_spiinitialize(void);
+
+#endif /* __ASSEMBLY__ */
+#endif /* __CONFIGS_STM3240G_EVAL_SRC_STM3240G_INTERNAL_H */
+
diff --git a/nuttx/configs/stm32f4discovery/src/up_autoleds.c b/nuttx/configs/stm32f4discovery/src/up_autoleds.c
new file mode 100644
index 000000000..5d97f8758
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_autoleds.c
@@ -0,0 +1,260 @@
+/****************************************************************************
+ * configs/stm3240g_eval/src/up_autoleds.c
+ * arch/arm/src/board/up_autoleds.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "up_arch.h"
+#include "up_internal.h"
+#include "stm32_internal.h"
+#include "stm32f4discovery-internal.h"
+
+#ifdef CONFIG_ARCH_LEDS
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/* Enables debug output from this file (needs CONFIG_DEBUG with
+ * CONFIG_DEBUG_VERBOSE too)
+ */
+
+#undef LED_DEBUG  /* Define to enable debug */
+
+#ifdef LED_DEBUG
+#  define leddbg  lldbg
+#  define ledvdbg llvdbg
+#else
+#  define leddbg(x...)
+#  define ledvdbg(x...)
+#endif
+
+/* The following definitions map the encoded LED setting to GPIO settings */
+
+#define STM3210E_LED1     (1 << 0)
+#define STM3210E_LED2     (1 << 1)
+#define STM3210E_LED3     (1 << 2)
+#define STM3210E_LED4     (1 << 3)
+
+#define ON_SETBITS_SHIFT  (0)
+#define ON_CLRBITS_SHIFT  (4)
+#define OFF_SETBITS_SHIFT (8)
+#define OFF_CLRBITS_SHIFT (12)
+
+#define ON_BITS(v)        ((v) & 0xff)
+#define OFF_BITS(v)       (((v) >> 8) & 0x0ff)
+#define SETBITS(b)        ((b) & 0x0f)
+#define CLRBITS(b)        (((b) >> 4) & 0x0f)
+
+#define ON_SETBITS(v)     (SETBITS(ON_BITS(v))
+#define ON_CLRBITS(v)     (CLRBITS(ON_BITS(v))
+#define OFF_SETBITS(v)    (SETBITS(OFF_BITS(v))
+#define OFF_CLRBITS(v)    (CLRBITS(OFF_BITS(v))
+
+#define LED_STARTED_ON_SETBITS       ((STM3210E_LED1) << ON_SETBITS_SHIFT)
+#define LED_STARTED_ON_CLRBITS       ((STM3210E_LED2|STM3210E_LED3|STM3210E_LED4) << ON_CLRBITS_SHIFT)
+#define LED_STARTED_OFF_SETBITS      (0 << OFF_SETBITS_SHIFT)
+#define LED_STARTED_OFF_CLRBITS      ((STM3210E_LED1|STM3210E_LED2|STM3210E_LED3|STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+#define LED_HEAPALLOCATE_ON_SETBITS  ((STM3210E_LED2) << ON_SETBITS_SHIFT)
+#define LED_HEAPALLOCATE_ON_CLRBITS  ((STM3210E_LED1|STM3210E_LED3|STM3210E_LED4) << ON_CLRBITS_SHIFT)
+#define LED_HEAPALLOCATE_OFF_SETBITS ((STM3210E_LED1) << OFF_SETBITS_SHIFT)
+#define LED_HEAPALLOCATE_OFF_CLRBITS ((STM3210E_LED2|STM3210E_LED3|STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+#define LED_IRQSENABLED_ON_SETBITS   ((STM3210E_LED1|STM3210E_LED2) << ON_SETBITS_SHIFT)
+#define LED_IRQSENABLED_ON_CLRBITS   ((STM3210E_LED3|STM3210E_LED4) << ON_CLRBITS_SHIFT)
+#define LED_IRQSENABLED_OFF_SETBITS  ((STM3210E_LED2) << OFF_SETBITS_SHIFT)
+#define LED_IRQSENABLED_OFF_CLRBITS  ((STM3210E_LED1|STM3210E_LED3|STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+#define LED_STACKCREATED_ON_SETBITS  ((STM3210E_LED3) << ON_SETBITS_SHIFT)
+#define LED_STACKCREATED_ON_CLRBITS  ((STM3210E_LED1|STM3210E_LED2|STM3210E_LED4) << ON_CLRBITS_SHIFT)
+#define LED_STACKCREATED_OFF_SETBITS ((STM3210E_LED1|STM3210E_LED2) << OFF_SETBITS_SHIFT)
+#define LED_STACKCREATED_OFF_CLRBITS ((STM3210E_LED3|STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+#define LED_INIRQ_ON_SETBITS         ((STM3210E_LED1) << ON_SETBITS_SHIFT)
+#define LED_INIRQ_ON_CLRBITS         ((0) << ON_CLRBITS_SHIFT)
+#define LED_INIRQ_OFF_SETBITS        ((0) << OFF_SETBITS_SHIFT)
+#define LED_INIRQ_OFF_CLRBITS        ((STM3210E_LED1) << OFF_CLRBITS_SHIFT)
+
+#define LED_SIGNAL_ON_SETBITS        ((STM3210E_LED2) << ON_SETBITS_SHIFT)
+#define LED_SIGNAL_ON_CLRBITS        ((0) << ON_CLRBITS_SHIFT)
+#define LED_SIGNAL_OFF_SETBITS       ((0) << OFF_SETBITS_SHIFT)
+#define LED_SIGNAL_OFF_CLRBITS       ((STM3210E_LED2) << OFF_CLRBITS_SHIFT)
+
+#define LED_ASSERTION_ON_SETBITS     ((STM3210E_LED4) << ON_SETBITS_SHIFT)
+#define LED_ASSERTION_ON_CLRBITS     ((0) << ON_CLRBITS_SHIFT)
+#define LED_ASSERTION_OFF_SETBITS    ((0) << OFF_SETBITS_SHIFT)
+#define LED_ASSERTION_OFF_CLRBITS    ((STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+#define LED_PANIC_ON_SETBITS         ((STM3210E_LED4) << ON_SETBITS_SHIFT)
+#define LED_PANIC_ON_CLRBITS         ((0) << ON_CLRBITS_SHIFT)
+#define LED_PANIC_OFF_SETBITS        ((0) << OFF_SETBITS_SHIFT)
+#define LED_PANIC_OFF_CLRBITS        ((STM3210E_LED4) << OFF_CLRBITS_SHIFT)
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+static const uint16_t g_ledbits[8] =
+{
+  (LED_STARTED_ON_SETBITS       | LED_STARTED_ON_CLRBITS |
+   LED_STARTED_OFF_SETBITS      | LED_STARTED_OFF_CLRBITS),
+
+  (LED_HEAPALLOCATE_ON_SETBITS  | LED_HEAPALLOCATE_ON_CLRBITS |
+   LED_HEAPALLOCATE_OFF_SETBITS | LED_HEAPALLOCATE_OFF_CLRBITS),
+
+  (LED_IRQSENABLED_ON_SETBITS   | LED_IRQSENABLED_ON_CLRBITS |
+   LED_IRQSENABLED_OFF_SETBITS  | LED_IRQSENABLED_OFF_CLRBITS),
+
+  (LED_STACKCREATED_ON_SETBITS  | LED_STACKCREATED_ON_CLRBITS |
+   LED_STACKCREATED_OFF_SETBITS | LED_STACKCREATED_OFF_CLRBITS),
+
+  (LED_INIRQ_ON_SETBITS         | LED_INIRQ_ON_CLRBITS |
+   LED_INIRQ_OFF_SETBITS        | LED_INIRQ_OFF_CLRBITS),
+
+  (LED_SIGNAL_ON_SETBITS        | LED_SIGNAL_ON_CLRBITS |
+   LED_SIGNAL_OFF_SETBITS       | LED_SIGNAL_OFF_CLRBITS),
+
+  (LED_ASSERTION_ON_SETBITS     | LED_ASSERTION_ON_CLRBITS |
+   LED_ASSERTION_OFF_SETBITS    | LED_ASSERTION_OFF_CLRBITS),
+
+  (LED_PANIC_ON_SETBITS         | LED_PANIC_ON_CLRBITS |
+   LED_PANIC_OFF_SETBITS        | LED_PANIC_OFF_CLRBITS)
+};
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+static inline void led_clrbits(unsigned int clrbits)
+{
+  if ((clrbits & STM3210E_LED1) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED1, false);
+    }
+
+  if ((clrbits & STM3210E_LED2) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED2, false);
+    }
+
+  if ((clrbits & STM3210E_LED3) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED3, false);
+    }
+
+  if ((clrbits & STM3210E_LED4) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED4, false);
+    }
+}
+
+static inline void led_setbits(unsigned int setbits)
+{
+  if ((setbits & STM3210E_LED1) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED1, true);
+    }
+
+  if ((setbits & STM3210E_LED2) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED2, true);
+    }
+
+  if ((setbits & STM3210E_LED3) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED3, true);
+    }
+
+  if ((setbits & STM3210E_LED4) != 0)
+    {
+      stm32_gpiowrite(GPIO_LED4, true);
+    }
+}
+
+static void led_setonoff(unsigned int bits)
+{
+  led_clrbits(CLRBITS(bits));
+  led_setbits(SETBITS(bits));
+}
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: up_ledinit
+ ****************************************************************************/
+
+void up_ledinit(void)
+{
+   /* Configure LED1-4 GPIOs for output */
+
+   stm32_configgpio(GPIO_LED1);
+   stm32_configgpio(GPIO_LED2);
+   stm32_configgpio(GPIO_LED3);
+   stm32_configgpio(GPIO_LED4);
+}
+
+/****************************************************************************
+ * Name: up_ledon
+ ****************************************************************************/
+
+void up_ledon(int led)
+{
+  led_setonoff(ON_BITS(g_ledbits[led]));
+}
+
+/****************************************************************************
+ * Name: up_ledoff
+ ****************************************************************************/
+
+void up_ledoff(int led)
+{
+  led_setonoff(OFF_BITS(g_ledbits[led]));
+}
+
+#endif /* CONFIG_ARCH_LEDS */
diff --git a/nuttx/configs/stm32f4discovery/src/up_boot.c b/nuttx/configs/stm32f4discovery/src/up_boot.c
new file mode 100644
index 000000000..791f0e5e7
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_boot.c
@@ -0,0 +1,90 @@
+/************************************************************************************

+ * configs/stm32f4discovery/src/up_boot.c

+ * arch/arm/src/board/up_boot.c

+ *

+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.

+ *   Author: Gregory Nutt <gnutt@nuttx.org>

+ *

+ * Redistribution and use in source and binary forms, with or without

+ * modification, are permitted provided that the following conditions

+ * are met:

+ *

+ * 1. Redistributions of source code must retain the above copyright

+ *    notice, this list of conditions and the following disclaimer.

+ * 2. Redistributions in binary form must reproduce the above copyright

+ *    notice, this list of conditions and the following disclaimer in

+ *    the documentation and/or other materials provided with the

+ *    distribution.

+ * 3. Neither the name NuttX nor the names of its contributors may be

+ *    used to endorse or promote products derived from this software

+ *    without specific prior written permission.

+ *

+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS

+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE

+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,

+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS

+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

+ * POSSIBILITY OF SUCH DAMAGE.

+ *

+ ************************************************************************************/

+

+/************************************************************************************

+ * Included Files

+ ************************************************************************************/

+

+#include <nuttx/config.h>

+

+#include <debug.h>

+

+#include <arch/board/board.h>

+

+#include "up_arch.h"

+#include "stm32f4discovery-internal.h"

+

+/************************************************************************************

+ * Definitions

+ ************************************************************************************/

+

+/************************************************************************************

+ * Private Functions

+ ************************************************************************************/

+

+/************************************************************************************

+ * Public Functions

+ ************************************************************************************/

+

+/************************************************************************************

+ * Name: stm32_boardinitialize

+ *

+ * Description:

+ *   All STM32 architectures must provide the following entry point.  This entry point

+ *   is called early in the intitialization -- after all memory has been configured

+ *   and mapped but before any devices have been initialized.

+ *

+ ************************************************************************************/

+

+void stm32_boardinitialize(void)

+{

+  /* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function

+   * stm32_spiinitialize() has been brought into the link.

+   */

+

+#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2) || defined(CONFIG_STM32_SPI3)

+  if (stm32_spiinitialize)

+    {

+      stm32_spiinitialize();

+    }

+#endif

+

+  /* Configure on-board LEDs if LED support has been selected. */

+

+#ifdef CONFIG_ARCH_LEDS

+  up_ledinit();

+#endif

+}

diff --git a/nuttx/configs/stm32f4discovery/src/up_buttons.c b/nuttx/configs/stm32f4discovery/src/up_buttons.c
new file mode 100644
index 000000000..60ac6c369
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_buttons.c
@@ -0,0 +1,165 @@
+/****************************************************************************
+ * configs/stm32f4discovery/src/up_buttons.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+
+#include <arch/board/board.h>
+#include "stm32f4discovery-internal.h"
+
+#ifdef CONFIG_ARCH_BUTTONS
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/* Pin configuration for each STM32F4 Discovery button.  This array is indexed by
+ * the BUTTON_* definitions in board.h
+ */
+
+static const uint16_t g_buttons[NUM_BUTTONS] =
+{
+  GPIO_BTN_USER
+};
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: up_buttoninit
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ ****************************************************************************/
+
+void up_buttoninit(void)
+{
+  int i;
+
+  /* Configure the GPIO pins as inputs.  NOTE that EXTI interrupts are 
+   * configured for all pins.
+   */
+
+  for (i = 0; i < NUM_BUTTONS; i++)
+    {
+      stm32_configgpio(g_buttons[i]);
+    }
+}
+
+/****************************************************************************
+ * Name: up_buttons
+ ****************************************************************************/
+
+uint8_t up_buttons(void)
+{
+  uint8_t ret = 0;
+  int i;
+
+  /* Check that state of each key */
+
+  for (i = 0; i < NUM_BUTTONS; i++)
+    {
+       /* A LOW value means that the key is pressed.
+        */
+
+       bool released = stm32_gpioread(g_buttons[i]);
+
+       /* Accumulate the set of depressed (not released) keys */
+
+       if (!released)
+         {
+            ret |= (1 << i);
+         }
+    }
+
+  return ret;
+}
+
+/************************************************************************************
+ * Button support.
+ *
+ * Description:
+ *   up_buttoninit() must be called to initialize button resources.  After
+ *   that, up_buttons() may be called to collect the current state of all
+ *   buttons or up_irqbutton() may be called to register button interrupt
+ *   handlers.
+ *
+ *   After up_buttoninit() has been called, up_buttons() may be called to
+ *   collect the state of all buttons.  up_buttons() returns an 8-bit bit set
+ *   with each bit associated with a button.  See the BUTTON_*_BIT
+ *   definitions in board.h for the meaning of each bit.
+ *
+ *   up_irqbutton() may be called to register an interrupt handler that will
+ *   be called when a button is depressed or released.  The ID value is a
+ *   button enumeration value that uniquely identifies a button resource. See the
+ *   BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.  The previous interrupt handler address is returned (so that it may
+ *   restored, if so desired).
+ *
+ ************************************************************************************/
+
+#ifdef CONFIG_ARCH_IRQBUTTONS
+xcpt_t up_irqbutton(int id, xcpt_t irqhandler)
+{
+  xcpt_t oldhandler = NULL;
+
+  /* The following should be atomic */
+
+  if (id >= MIN_IRQBUTTON && id <= MAX_IRQBUTTON)
+    {
+      oldhandler = stm32_gpiosetevent(g_buttons[id], true, true, true, irqhandler);
+    }
+  return oldhandler;
+}
+#endif
+#endif /* CONFIG_ARCH_BUTTONS */
diff --git a/nuttx/configs/stm32f4discovery/src/up_pwm.c b/nuttx/configs/stm32f4discovery/src/up_pwm.c
new file mode 100644
index 000000000..02c71b503
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_pwm.c
@@ -0,0 +1,142 @@
+/************************************************************************************
+ * configs/stm32f4discovery/src/up_pwm.c
+ * arch/arm/src/board/up_pwm.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <errno.h>
+#include <debug.h>
+
+#include <nuttx/pwm.h>
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "up_arch.h"
+#include "stm32_pwm.h"
+#include "stm32f4discovery-internal.h"
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+/* Configuration *******************************************************************/
+/* PWM
+ *
+ * The stm32f4discovery has no real on-board PWM devices, but the board can be configured to output
+ * a pulse train using TIM4 CH2.  This pin is used by FSMC is connect to CN5 just for this
+ * purpose:
+ *
+ * PD13 FSMC_A18 / MC_TIM4_CH2OUT pin 33 (EnB)
+ *
+ * FSMC must be disabled in this case!
+ */
+
+#define HAVE_PWM 1
+
+#ifndef CONFIG_PWM
+#  undef HAVE_PWM
+#endif
+
+#ifndef CONFIG_STM32_TIM4
+#  undef HAVE_PWM
+#endif
+
+#ifndef CONFIG_STM32_TIM4_PWM
+#  undef HAVE_PWM
+#endif
+
+#if CONFIG_STM32_TIM4_CHANNEL != STM3240G_EVAL_PWMCHANNEL
+#  undef HAVE_PWM
+#endif
+
+#ifdef HAVE_PWM
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: pwm_devinit
+ *
+ * Description:
+ *   All STM32 architectures must provide the following interface to work with
+ *   examples/pwm.
+ *
+ ************************************************************************************/
+
+int pwm_devinit(void)
+{
+  static bool initialized = false;
+  struct pwm_lowerhalf_s *pwm;
+  int ret;
+
+  /* Have we already initialized? */
+
+  if (!initialized)
+    {
+      /* Call stm32_pwminitialize() to get an instance of the PWM interface */
+
+      pwm = stm32_pwminitialize(STM3240G_EVAL_PWMTIMER);
+      if (!pwm)
+        {
+          dbg("Failed to get the STM32 PWM lower half\n");
+          return -ENODEV;
+        }
+
+      /* Register the PWM driver at "/dev/pwm0" */
+
+      ret = pwm_register("/dev/pwm0", pwm);
+      if (ret < 0)
+        {
+          adbg("pwm_register failed: %d\n", ret);
+          return ret;
+        }
+
+      /* Now we are initialized */
+
+      initialized = true;
+    }
+
+  return OK;
+}
+
+#endif /* HAVE_PWM */
diff --git a/nuttx/configs/stm32f4discovery/src/up_spi.c b/nuttx/configs/stm32f4discovery/src/up_spi.c
new file mode 100644
index 000000000..9b6a0b0f5
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_spi.c
@@ -0,0 +1,165 @@
+/************************************************************************************
+ * configs/stm3240g_eval/src/up_spi.c
+ * arch/arm/src/board/up_spi.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/spi.h>
+#include <arch/board/board.h>
+
+#include "up_arch.h"
+#include "chip.h"
+#include "stm32_internal.h"
+#include "stm32f4discovery-internal.h"
+
+#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2) || defined(CONFIG_STM32_SPI3)
+
+/************************************************************************************
+ * Definitions
+ ************************************************************************************/
+
+/* Enables debug output from this file (needs CONFIG_DEBUG too) */
+
+#undef SPI_DEBUG   /* Define to enable debug */
+#undef SPI_VERBOSE /* Define to enable verbose debug */
+
+#ifdef SPI_DEBUG
+#  define spidbg  lldbg
+#  ifdef SPI_VERBOSE
+#    define spivdbg lldbg
+#  else
+#    define spivdbg(x...)
+#  endif
+#else
+#  undef SPI_VERBOSE
+#  define spidbg(x...)
+#  define spivdbg(x...)
+#endif
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the stm32f4discovery board.
+ *
+ ************************************************************************************/
+
+void weak_function stm32_spiinitialize(void)
+{
+  stm32_configgpio(GPIO_SPI1_MISO);
+  stm32_configgpio(GPIO_SPI1_MOSI);
+  stm32_configgpio(GPIO_SPI1_SCK);
+}
+
+/****************************************************************************
+ * Name:  stm32_spi1/2/3select and stm32_spi1/2/3status
+ *
+ * Description:
+ *   The external functions, stm32_spi1/2/3select and stm32_spi1/2/3status must be
+ *   provided by board-specific logic.  They are implementations of the select
+ *   and status methods of the SPI interface defined by struct spi_ops_s (see
+ *   include/nuttx/spi.h). All other methods (including up_spiinitialize())
+ *   are provided by common STM32 logic.  To use this common SPI logic on your
+ *   board:
+ *
+ *   1. Provide logic in stm32_boardinitialize() to configure SPI chip select
+ *      pins.
+ *   2. Provide stm32_spi1/2/3select() and stm32_spi1/2/3status() functions in your
+ *      board-specific logic.  These functions will perform chip selection and
+ *      status operations using GPIOs in the way your board is configured.
+ *   3. Add a calls to up_spiinitialize() in your low level application
+ *      initialization logic
+ *   4. The handle returned by up_spiinitialize() may then be used to bind the
+ *      SPI driver to higher level logic (e.g., calling
+ *      mmcsd_spislotinitialize(), for example, will bind the SPI driver to
+ *      the SPI MMC/SD driver).
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_STM32_SPI1
+void stm32_spi1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+
+  stm32_gpiowrite(GPIO_CS_MEMS, !selected);
+}
+
+uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI2
+void stm32_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+}
+
+uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI3
+void stm32_spi3select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+  spidbg("devid: %d CS: %s\n", (int)devid, selected ? "assert" : "de-assert");
+}
+
+uint8_t stm32_spi3status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+  return SPI_STATUS_PRESENT;
+}
+#endif
+
+#endif /* CONFIG_STM32_SPI1 || CONFIG_STM32_SPI2 */
diff --git a/nuttx/configs/stm32f4discovery/src/up_userleds.c b/nuttx/configs/stm32f4discovery/src/up_userleds.c
new file mode 100644
index 000000000..d5eb699ef
--- /dev/null
+++ b/nuttx/configs/stm32f4discovery/src/up_userleds.c
@@ -0,0 +1,131 @@
+/****************************************************************************
+ * configs/stm3240g_eval/src/up_leds.c
+ * arch/arm/src/board/up_leds.c
+ *
+ *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "up_arch.h"
+#include "up_internal.h"
+#include "stm32_internal.h"
+#include "stm32f4discovery-internal.h"
+
+#ifndef CONFIG_ARCH_LEDS
+
+/****************************************************************************
+ * Definitions
+ ****************************************************************************/
+
+/* Enables debug output from this file (needs CONFIG_DEBUG with
+ * CONFIG_DEBUG_VERBOSE too)
+ */
+
+#undef LED_DEBUG  /* Define to enable debug */
+
+#ifdef LED_DEBUG
+#  define leddbg  lldbg
+#  define ledvdbg llvdbg
+#else
+#  define leddbg(x...)
+#  define ledvdbg(x...)
+#endif
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+/* This array maps an LED number to GPIO pin configuration */
+
+static uint32_t g_ledcfg[BOARD_NLEDS] = 
+{
+  GPIO_LED1, GPIO_LED2, GPIO_LED3, GPIO_LED4
+};
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_ledinit
+ ****************************************************************************/
+
+void stm32_ledinit(void)
+{
+   /* Configure LED1-4 GPIOs for output */
+
+   stm32_configgpio(GPIO_LED1);
+   stm32_configgpio(GPIO_LED2);
+   stm32_configgpio(GPIO_LED3);
+   stm32_configgpio(GPIO_LED4);
+}
+
+/****************************************************************************
+ * Name: stm32_setled
+ ****************************************************************************/
+
+void stm32_setled(int led, bool ledon)
+{
+  if ((unsigned)led < BOARD_NLEDS)
+    {
+      stm32_gpiowrite(g_ledcfg[led], ledon);
+    }
+}
+
+/****************************************************************************
+ * Name: stm32_setleds
+ ****************************************************************************/
+
+void stm32_setleds(uint8_t ledset)
+{
+  stm32_gpiowrite(BOARD_LED1, (ledset & BOARD_LED1_BIT) == 0);
+  stm32_gpiowrite(BOARD_LED2, (ledset & BOARD_LED2_BIT) == 0);
+  stm32_gpiowrite(BOARD_LED3, (ledset & BOARD_LED3_BIT) == 0);
+  stm32_gpiowrite(BOARD_LED4, (ledset & BOARD_LED4_BIT) == 0);
+}
+
+#endif /* !CONFIG_ARCH_LEDS */