diff options
-rw-r--r-- | nuttx/arch/arm/src/sam34/sam3u_gpio.h | 25 | ||||
-rw-r--r-- | nuttx/arch/arm/src/sam34/sam_gpioirq.c | 6 | ||||
-rwxr-xr-x | nuttx/configs/sam3u-ek/knsh/setenv.sh | 2 | ||||
-rwxr-xr-x | nuttx/configs/sam3u-ek/nsh/setenv.sh | 2 | ||||
-rwxr-xr-x | nuttx/configs/sam3u-ek/nx/setenv.sh | 2 | ||||
-rwxr-xr-x | nuttx/configs/sam3u-ek/ostest/setenv.sh | 2 | ||||
-rw-r--r-- | nuttx/configs/sam3u-ek/src/sam3u-ek.h | 73 | ||||
-rw-r--r-- | nuttx/configs/sam4s-xplained/src/sam4s-xplained.h | 2 |
8 files changed, 64 insertions, 50 deletions
diff --git a/nuttx/arch/arm/src/sam34/sam3u_gpio.h b/nuttx/arch/arm/src/sam34/sam3u_gpio.h index 84f543056..74716bb3a 100644 --- a/nuttx/arch/arm/src/sam34/sam3u_gpio.h +++ b/nuttx/arch/arm/src/sam34/sam3u_gpio.h @@ -56,7 +56,7 @@ /* 16-bit Encoding: * - * MMCC CII. VPPB BBBB + * MMCC CIII VPPB BBBB */ /* Input/Output mode: @@ -85,17 +85,22 @@ /* Additional interrupt modes: * - * .... .II. .... .... + * .... .III .... .... */ -#define GPIO_INT_SHIFT (9) /* Bits 9-10: GPIO interrupt bits */ -#define GPIO_INT_MASK (3 << GPIO_INT_SHIFT) -# define GPIO_INT_LEVEL (1 << 10) /* Bit 10: Level detection interrupt */ -# define GPIO_INT_EDGE (0) /* (vs. Edge detection interrupt) */ -# define GPIO_INT_HIGHLEVEL (1 << 9) /* Bit 9: High level detection interrupt */ -# define GPIO_INT_LOWLEVEL (0) /* (vs. Low level detection interrupt) */ -# define GPIO_INT_RISING (1 << 9) /* Bit 9: Rising edge detection interrupt */ -# define GPIO_INT_FALLING (0) /* (vs. Falling edge detection interrupt) */ +#define GPIO_INT_SHIFT (8) /* Bits 8-10: GPIO interrupt bits */ +#define GPIO_INT_MASK (7 << GPIO_INT_SHIFT) +# define _GIO_INT_AIM (1 << 10) /* Bit 10: Additional Interrupt modes */ +# define _GPIO_INT_LEVEL (1 << 9) /* Bit 9: Level detection interrupt */ +# define _GPIO_INT_EDGE (0) /* (vs. Edge detection interrupt) */ +# define _GPIO_INT_RH (1 << 8) /* Bit 9: Rising edge/High level detection interrupt */ +# define _GPIO_INT_FL (0) /* (vs. Falling edge/Low level detection interrupt) */ + +# define GPIO_INT_HIGHLEVEL (_GIO_INT_AIM | _GPIO_INT_LEVEL | _GPIO_INT_RH) +# define GPIO_INT_LOWLEVEL (_GIO_INT_AIM | _GPIO_INT_LEVEL | _GPIO_INT_FL) +# define GPIO_INT_RISING (_GIO_INT_AIM | _GPIO_INT_EDGE | _GPIO_INT_RH) +# define GPIO_INT_FALLING (_GIO_INT_AIM | _GPIO_INT_EDGE | _GPIO_INT_FL) +# define GPIO_INT_BOTHEDGES (0) /* If the pin is an GPIO output, then this identifies the initial output value: * diff --git a/nuttx/arch/arm/src/sam34/sam_gpioirq.c b/nuttx/arch/arm/src/sam34/sam_gpioirq.c index b7c7ead27..11ea34aa6 100644 --- a/nuttx/arch/arm/src/sam34/sam_gpioirq.c +++ b/nuttx/arch/arm/src/sam34/sam_gpioirq.c @@ -280,7 +280,7 @@ void sam_gpioirq(uint16_t pinset) /* Are any additional interrupt modes selected? */ - if ((pinset & GPIO_INT_MASK) != 0) + if ((pinset & _GIO_INT_AIM) != 0) { /* Yes.. Enable additional interrupt mode */ @@ -288,7 +288,7 @@ void sam_gpioirq(uint16_t pinset) /* Level or edge detected interrupt? */ - if ((pinset & GPIO_INT_LEVEL) != 0) + if ((pinset & _GPIO_INT_LEVEL) != 0) { putreg32(pin, base + SAM_PIO_LSR_OFFSET); /* Level */ } @@ -299,7 +299,7 @@ void sam_gpioirq(uint16_t pinset) /* High level/rising edge or low level /falling edge? */ - if ((pinset & GPIO_INT_HIGHLEVEL) != 0) + if ((pinset & _GPIO_INT_RH) != 0) { putreg32(pin, base + SAM_PIO_REHLSR_OFFSET); /* High level/Rising edge */ } diff --git a/nuttx/configs/sam3u-ek/knsh/setenv.sh b/nuttx/configs/sam3u-ek/knsh/setenv.sh index 3e81f9ccb..9755bc285 100755 --- a/nuttx/configs/sam3u-ek/knsh/setenv.sh +++ b/nuttx/configs/sam3u-ek/knsh/setenv.sh @@ -55,7 +55,7 @@ fi # This is the Cygwin path to the location where I installed the CodeSourcery # toolchain under windows. You will also have to edit this if you install # the CodeSourcery toolchain in any other location -export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" +#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" # These are the Cygwin paths to the locations where I installed the Atollic # toolchain under windows. You will also have to edit this if you install diff --git a/nuttx/configs/sam3u-ek/nsh/setenv.sh b/nuttx/configs/sam3u-ek/nsh/setenv.sh index e23957670..c867a5e55 100755 --- a/nuttx/configs/sam3u-ek/nsh/setenv.sh +++ b/nuttx/configs/sam3u-ek/nsh/setenv.sh @@ -55,7 +55,7 @@ fi # This is the Cygwin path to the location where I installed the CodeSourcery # toolchain under windows. You will also have to edit this if you install # the CodeSourcery toolchain in any other location -export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" +#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" # These are the Cygwin paths to the locations where I installed the Atollic # toolchain under windows. You will also have to edit this if you install diff --git a/nuttx/configs/sam3u-ek/nx/setenv.sh b/nuttx/configs/sam3u-ek/nx/setenv.sh index d0a5dea3d..87a085b98 100755 --- a/nuttx/configs/sam3u-ek/nx/setenv.sh +++ b/nuttx/configs/sam3u-ek/nx/setenv.sh @@ -54,7 +54,7 @@ fi # This is the Cygwin path to the location where I installed the CodeSourcery # toolchain under windows. You will also have to edit this if you install # the CodeSourcery toolchain in any other location -export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" +#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" # These are the Cygwin paths to the locations where I installed the Atollic # toolchain under windows. You will also have to edit this if you install diff --git a/nuttx/configs/sam3u-ek/ostest/setenv.sh b/nuttx/configs/sam3u-ek/ostest/setenv.sh index 195dccc5c..1c9e008e3 100755 --- a/nuttx/configs/sam3u-ek/ostest/setenv.sh +++ b/nuttx/configs/sam3u-ek/ostest/setenv.sh @@ -55,7 +55,7 @@ fi # This is the Cygwin path to the location where I installed the CodeSourcery # toolchain under windows. You will also have to edit this if you install # the CodeSourcery toolchain in any other location -export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" +#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" # These are the Cygwin paths to the locations where I installed the Atollic # toolchain under windows. You will also have to edit this if you install diff --git a/nuttx/configs/sam3u-ek/src/sam3u-ek.h b/nuttx/configs/sam3u-ek/src/sam3u-ek.h index df53985cf..24d0d99e2 100644 --- a/nuttx/configs/sam3u-ek/src/sam3u-ek.h +++ b/nuttx/configs/sam3u-ek/src/sam3u-ek.h @@ -112,61 +112,70 @@ * 39 K Backlight ground N/A --- --- --- */ -#define GPIO_LCD_NCS2 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOC|GPIO_PIN16) -#define GPIO_LCD_RS (GPIO_PERIPHB|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN8) -#define GPIO_LCD_NWE (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN23) -#define GPIO_LCD_NRD (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN19) - -#define GPIO_LCD_D0 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN9) -#define GPIO_LCD_D1 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN10) -#define GPIO_LCD_D2 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN11) -#define GPIO_LCD_D3 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN12) -#define GPIO_LCD_D4 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN13) -#define GPIO_LCD_D5 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN14) -#define GPIO_LCD_D6 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN15) -#define GPIO_LCD_D7 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN16) -#define GPIO_LCD_D8 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN25) -#define GPIO_LCD_D9 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN26) -#define GPIO_LCD_D10 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN27) -#define GPIO_LCD_D11 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN28) -#define GPIO_LCD_D12 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN29) -#define GPIO_LCD_D13 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN30) -#define GPIO_LCD_D14 (GPIO_PERIPHA|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN31) -#define GPIO_LCD_D15 (GPIO_PERIPHB|GPIO_CFG_PULLUP|GPIO_PORT_PIOB|GPIO_PIN6) +#define GPIO_LCD_NCS2 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOC | GPIO_PIN16) +#define GPIO_LCD_RS (GPIO_PERIPHB | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN8) +#define GPIO_LCD_NWE (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN23) +#define GPIO_LCD_NRD (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN19) + +#define GPIO_LCD_D0 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN9) +#define GPIO_LCD_D1 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN10) +#define GPIO_LCD_D2 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN11) +#define GPIO_LCD_D3 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN12) +#define GPIO_LCD_D4 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN13) +#define GPIO_LCD_D5 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN14) +#define GPIO_LCD_D6 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN15) +#define GPIO_LCD_D7 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN16) +#define GPIO_LCD_D8 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN25) +#define GPIO_LCD_D9 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN26) +#define GPIO_LCD_D10 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN27) +#define GPIO_LCD_D11 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN28) +#define GPIO_LCD_D12 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN29) +#define GPIO_LCD_D13 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN30) +#define GPIO_LCD_D14 (GPIO_PERIPHA | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN31) +#define GPIO_LCD_D15 (GPIO_PERIPHB | GPIO_CFG_PULLUP | GPIO_PORT_PIOB | GPIO_PIN6) /* LCD Backlight pin definition. */ -#define GPIO_LCD_BKL (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_OUTPUT_CLEAR|GPIO_PORT_PIOC|GPIO_PIN19) +#define GPIO_LCD_BKL (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \ + GPIO_PORT_PIOC | GPIO_PIN19) /* Touchscreen controller (TSC) * + * The IRQ is active low and pulled up. + * * BUSY is high impedance when CS is high (not selected). When CS is * is low, BUSY is active high. Since the pin is pulled up, it will appear * busy if CS is not selected. */ -#define GPIO_TCS_IRQ (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_PORT_PIOA|GPIO_PIN24) -#define GPIO_TCS_BUSY (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_PORT_PIOA|GPIO_PIN2) +#define GPIO_TCS_IRQ (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_INT_BOTHEDGES | \ + GPIO_PORT_PIOA | GPIO_PIN24) +#define GPIO_TCS_BUSY (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_PORT_PIOA | GPIO_PIN2) #define SAM_TCS_IRQ SAM_IRQ_PA24 /* LEDs */ -#define GPIO_LED0 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_CLEAR|GPIO_PIN0) -#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN1) -#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CFG_DEFAULT|GPIO_PORT_PIOB|GPIO_OUTPUT_SET|GPIO_PIN2) +#define GPIO_LED0 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_PORT_PIOB | \ + GPIO_OUTPUT_CLEAR | GPIO_PIN0) +#define GPIO_LED1 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_PORT_PIOB | \ + GPIO_OUTPUT_SET | GPIO_PIN1) +#define GPIO_LED2 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_PORT_PIOB | \ + GPIO_OUTPUT_SET | GPIO_PIN2) /* BUTTONS */ -#define GPIO_BUTTON1 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN18) -#define GPIO_BUTTON2 (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_CFG_DEGLITCH|GPIO_PORT_PIOA|GPIO_PIN19) +#define GPIO_BUTTON1 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | GPIO_INT_BOTHEDGES | \ + GPIO_PORT_PIOA | GPIO_PIN18) +#define GPIO_BUTTON2 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | GPIO_INT_BOTHEDGES | \ + GPIO_PORT_PIOA | GPIO_PIN19) #define IRQ_BUTTON1 SAM_IRQ_PA18 #define IRQ_BUTTON2 SAM_IRQ_PA19 /* SD Card Detect */ -#define GPIO_MCI_CD (GPIO_INPUT|GPIO_CFG_PULLUP|GPIO_PORT_PIOA|GPIO_PIN25) +#define GPIO_MCI_CD (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_PORT_PIOA | GPIO_PIN25) /* SPI Chip Selects */ @@ -179,8 +188,8 @@ * it low throughout the SPI transfer. */ -#define GPIO_TSC_NPCS2 (GPIO_OUTPUT|GPIO_CFG_PULLUP|GPIO_OUTPUT_SET|\ - GPIO_PORT_PIOC|GPIO_PIN14) +#define GPIO_TSC_NPCS2 (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \ + GPIO_PORT_PIOC | GPIO_PIN14) /************************************************************************************ * Public Types diff --git a/nuttx/configs/sam4s-xplained/src/sam4s-xplained.h b/nuttx/configs/sam4s-xplained/src/sam4s-xplained.h index f9ea61858..1d6877d33 100644 --- a/nuttx/configs/sam4s-xplained/src/sam4s-xplained.h +++ b/nuttx/configs/sam4s-xplained/src/sam4s-xplained.h @@ -102,7 +102,7 @@ */ #define GPIO_BP2 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \ - GPIO_PORT_PIOA | GPIO_PIN5) + GPIO_INT_BOTHEDGES | GPIO_PORT_PIOA | GPIO_PIN5) #define IRQ_BP2 SAM_IRQ_PA5 /************************************************************************************ |