diff options
-rw-r--r-- | nuttx/configs/open1788/README.txt | 26 | ||||
-rw-r--r-- | nuttx/configs/open1788/include/board.h | 13 | ||||
-rw-r--r-- | nuttx/configs/open1788/src/lpc17_buttons.c | 53 | ||||
-rw-r--r-- | nuttx/configs/open1788/src/open1788.h | 52 |
4 files changed, 96 insertions, 48 deletions
diff --git a/nuttx/configs/open1788/README.txt b/nuttx/configs/open1788/README.txt index c828a1812..35d7cace4 100644 --- a/nuttx/configs/open1788/README.txt +++ b/nuttx/configs/open1788/README.txt @@ -560,6 +560,32 @@ CONFIGURATION CONFIG_DEBUG_VERBOSE=y CONFIG_DEBUG_INPUT=y + 7. The button test (apps/examples/buttons) can be built-in by adding + the following options. See apps/examples/README.txt for further + information about the button test. + + System Type: + CONFIG_GPIO_IRQ=y + + Board Selection: + CONFIG_ARCH_BUTTONS=y + CONFIG_ARCH_IRQBUTTONS=y + + Application Configuration: + CONFIG_EXAMPLES_BUTTONS=y + CONFIG_EXAMPLES_BUTTONS_MIN=0 + CONFIG_EXAMPLES_BUTTONS_MAX=7 + CONFIG_EXAMPLES_IRQBUTTONS_MIN=1 + CONFIG_EXAMPLES_IRQBUTTONS_MAX=7 + CONFIG_EXAMPLES_BUTTONS_NAME0="USER1" + CONFIG_EXAMPLES_BUTTONS_NAME1="USER2" + CONFIG_EXAMPLES_BUTTONS_NAME2="USER3" + CONFIG_EXAMPLES_BUTTONS_NAME3="JOYSTICK_A" + CONFIG_EXAMPLES_BUTTONS_NAME4="JOYSTICK_B" + CONFIG_EXAMPLES_BUTTONS_NAME5="JOYSTICK_C" + CONFIG_EXAMPLES_BUTTONS_NAME6="JOYSTICK_D" + CONFIG_EXAMPLES_BUTTONS_NAME7="JOYSTICK_CTR" + nxlines ------- Configures the graphics example located at examples/nsh. This diff --git a/nuttx/configs/open1788/include/board.h b/nuttx/configs/open1788/include/board.h index 2283f93d2..641cc99fe 100644 --- a/nuttx/configs/open1788/include/board.h +++ b/nuttx/configs/open1788/include/board.h @@ -258,8 +258,10 @@ * OFF while sleeping */ /* Button definitions ***************************************************************/ -/* The Open1788 supports several buttons. All will read "1" when open and "0" - * when closed +/* The Open1788 supports several buttons. All must be pulled up by the Open1788. + * When closed, the pins will be pulled to ground. So the buttons will read "1" + * when open and "0" when closed. All except USER1 are capable of generating + * interrupts. * * USER1 -- Connected to P4[26] * USER2 -- Connected to P2[22] @@ -271,12 +273,13 @@ * JOY_B -- Connected to P2[26] * JOY_C -- Connected to P2[23] * JOY_D -- Connected to P2[19] - * JOY_CTR -- Connected to P0[14] + * JOY_CTR -- Connected to P0[14] (shared with SSP1 SSEL) * - * The switches are all connected to ground and should be pulled up and sensed - * with a value of '0' when closed. + * For the interrupting buttons, interrupts are generated on both edges (press and + * release). */ + #define BOARD_BUTTON_USER1 0 #define BOARD_BUTTON_USER2 1 #define BOARD_BUTTON_USER3 2 diff --git a/nuttx/configs/open1788/src/lpc17_buttons.c b/nuttx/configs/open1788/src/lpc17_buttons.c index 474924510..c820e01f5 100644 --- a/nuttx/configs/open1788/src/lpc17_buttons.c +++ b/nuttx/configs/open1788/src/lpc17_buttons.c @@ -101,7 +101,7 @@ static xcpt_t g_buttonisr[BOARD_NUM_BUTTONS]; static uint8_t g_buttonirq[BOARD_NUM_BUTTONS] = { - GPIO_USER1_IRQ, GPIO_USER2_IRQ, GPIO_USER3_IRQ, GPIO_JOY_A_IRQ, + 0, GPIO_USER2_IRQ, GPIO_USER3_IRQ, GPIO_JOY_A_IRQ, GPIO_JOY_B_IRQ, GPIO_JOY_C_IRQ, GPIO_JOY_D_IRQ, GPIO_JOY_CTR_IRQ }; #endif @@ -209,36 +209,43 @@ xcpt_t up_irqbutton(int id, xcpt_t irqhandler) if ((unsigned)id < BOARD_NUM_BUTTONS) { - /* Return the current button handler and set the new interrupt handler */ + /* Get the IRQ number for the button; A value of zero indicates that + * the button does not support the interrupt function. + */ - oldhandler = g_buttonisr[id]; - g_buttonisr[id] = irqhandler; + irq = g_buttonirq[id]; + if (irq > 0) + { + /* Disable interrupts until we are done */ - /* Disable interrupts until we are done */ + flags = irqsave(); - flags = irqsave(); + /* Return the current button handler and set the new interrupt handler */ - /* Configure the interrupt. Either attach and enable the new - * interrupt or disable and detach the old interrupt handler. - */ + oldhandler = g_buttonisr[id]; + g_buttonisr[id] = irqhandler; - irq = g_buttonirq[id]; - if (irqhandler) - { - /* Attach then enable the new interrupt handler */ + /* Configure the interrupt. Either attach and enable the new + * interrupt or disable and detach the old interrupt handler. + */ - (void)irq_attach(irq, irqhandler); - up_enable_irq(irq); - } - else - { - /* Disable then then detach the the old interrupt handler */ + if (irqhandler) + { + /* Attach then enable the new interrupt handler */ - up_disable_irq(irq); - (void)irq_detach(irq); - } + (void)irq_attach(irq, irqhandler); + up_enable_irq(irq); + } + else + { + /* Disable then then detach the the old interrupt handler */ - irqrestore(flags); + up_disable_irq(irq); + (void)irq_detach(irq); + } + + irqrestore(flags); + } } return oldhandler; diff --git a/nuttx/configs/open1788/src/open1788.h b/nuttx/configs/open1788/src/open1788.h index e70eebe5d..3bceee1ec 100644 --- a/nuttx/configs/open1788/src/open1788.h +++ b/nuttx/configs/open1788/src/open1788.h @@ -53,7 +53,7 @@ * reconfigure this pin as normal GPIO input if NAND is used. */ -#define GPIO_NAND_RB (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN21) +#define GPIO_NAND_RB (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN21) /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in * any way. The following definitions are used to access individual LEDs. @@ -66,14 +66,16 @@ * These LEDs are connecte to ground so a high output value will illuminate them. */ -#define GPIO_LED1 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT1 | GPIO_PIN14) -#define GPIO_LED2 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT0 | GPIO_PIN16) -#define GPIO_LED3 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT1 | GPIO_PIN13) -#define GPIO_LED4 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT4 | GPIO_PIN27) +#define GPIO_LED1 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT1 | GPIO_PIN14) +#define GPIO_LED2 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT0 | GPIO_PIN16) +#define GPIO_LED3 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT1 | GPIO_PIN13) +#define GPIO_LED4 (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT4 | GPIO_PIN27) /* Button definitions ***************************************************************/ -/* The Open1788 supports several buttons. All will read "1" when open and "0" - * when closed +/* The Open1788 supports several buttons. All must be pulled up by the Open1788. + * When closed, the pins will be pulled to ground. So the buttons will read "1" + * when open and "0" when closed. All except USER1 are capable of generating + * interrupts. * * USER1 -- Connected to P4[26] * USER2 -- Connected to P2[22] @@ -85,21 +87,31 @@ * JOY_B -- Connected to P2[26] * JOY_C -- Connected to P2[23] * JOY_D -- Connected to P2[19] - * JOY_CTR -- Connected to P0[14] + * JOY_CTR -- Connected to P0[14] (shared with SSP1 SSEL) * - * The switches are all connected to ground and should be pulled up and sensed - * with a value of '0' when closed. + * For the interrupting buttons, interrupts are generated on both edges (press and + * release). */ -#define GPIO_USER1 (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT4 | GPIO_PIN26) -#define GPIO_USER2 (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT2 | GPIO_PIN22) -#define GPIO_USER3 (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT0 | GPIO_PIN10) +#define GPIO_USER1 (GPIO_INPUT | GPIO_PULLUP | GPIO_PORT4 | GPIO_PIN26) +#define GPIO_USER2 (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN22) +#define GPIO_USER3 (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN10) -#define GPIO_JOY_A (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT2 | GPIO_PIN25) -#define GPIO_JOY_B (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT2 | GPIO_PIN26) -#define GPIO_JOY_C (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT2 | GPIO_PIN23) -#define GPIO_JOY_D (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT2 | GPIO_PIN19) -#define GPIO_JOY_CTR (GPIO_INTBOTH | GPIO_FLOAT | GPIO_PORT0 | GPIO_PIN14) +#define GPIO_JOY_A (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN25) +#define GPIO_JOY_B (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN26) +#define GPIO_JOY_C (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN23) +#define GPIO_JOY_D (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT2 | GPIO_PIN19) +#define GPIO_JOY_CTR (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN14) + +/* IRQ numbers for the buttons that do support interrrupts */ + +#define GPIO_USER2_IRQ LPC17_IRQ_P2p22 +#define GPIO_USER3_IRQ LPC17_IRQ_P0p10 +#define GPIO_JOY_A_IRQ LPC17_IRQ_P2p25 +#define GPIO_JOY_B_IRQ LPC17_IRQ_P2p26 +#define GPIO_JOY_C_IRQ LPC17_IRQ_P2p23 +#define GPIO_JOY_D_IRQ LPC17_IRQ_P2p19 +#define GPIO_JOY_CTR_IRQ LPC17_IRQ_P0p14 /* SD Card **************************************************************************/ /* The SD card detect (CD) signal is on P0[13]. This signal is shared. It is also @@ -109,12 +121,12 @@ * The CD pin is interrupting: */ -#define GPIO_SD_CD (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN13) +#define GPIO_SD_CD (GPIO_INTBOTH | GPIO_PULLUP | GPIO_PORT0 | GPIO_PIN13) /* LCD ******************************************************************************/ /* Backlight enable, P2[1]. Initial state is OFF (zero) */ -#define GPIO_LCD_BL (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT2 | GPIO_PIN1) +#define GPIO_LCD_BL (GPIO_OUTPUT | GPIO_VALUE_ZERO | GPIO_PORT2 | GPIO_PIN1) /* XPT2046 Touchscreen **************************************************************/ /* -------------- -------------------- ------------ -------------- |