blob: 86a500ecff05c3b43e90b4fe4f1bd25cb051463c (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
AVAILABLE CONFIGURATIONS
^^^^^^^^^^^^^^^^^^^^^^^^
arm-defconfig
Builds an ARM toolchain using gcc 3.4.5
arm920t-defconfig-4.2.4
arm926t-defconfig-4.2.4
Builds an ARM toolchain using gcc 4.2.4. This configuration
builds both gcc and g++. There are two versions: one for
arm920t (armv4t) and arm926t (arv5t) because of differences
in the way that soft floating is handled in these two architectures.
NOTE: At present, there are issues with some of the binutils
programs (arm-elf-objcopy in particular) that cause Floating
point exceptions when trying to build NuttX. This is probably
due to improperly positioned sections and can probably fixed
by changing the architectures .ldscript file.
cortexm3-defconfig-4.3.3
Builds an ARM toolchain for the Cortex-M3 using gcc 4.3.3.
This configuration builds both gcc and g++.
NOTE: This configuration is untested as of this writing.
bfin-defconfig-4.2.4
Builds an Blackfin toolchain using gcc 4.2.4
h8300_config
Builds an H8/300 toolchain using gcc 3.4.5
m68hc11-config
Builds an hc11 toolchain using gcc 3.4.5
m68k-config
Builds an M68K toolchain using gcc 3.4.5
sh-defconfig
Builds an SH-1/2 toolchain using gcc 3.4.5
GENERAL BUILD STEPS
^^^^^^^^^^^^^^^^^^^
1. CD to the correct directory.
Change to the directory just above the NuttX installation. If <nuttx-dir> is
where NuttX is installed, then cd to <nuttx-dir>/..
2. Get and Install the buildroot Module
a. Using a release tarball:
cd <nuttx-dir>/..
Download the appropriate buildroot package.
unpack the buildroot package
rename the directory to buildroot
b. Using CVS
Check out the misc/buildroot module. CVS checkout instructions:
cvs -d:pserver:anonymous@nuttx.cvs.sourceforge.net:/cvsroot/nuttx login
cvs -z3 -d:pserver:anonymous@nuttx.cvs.sourceforge.net:/cvsroot/nuttx co -P misc/buildroot
Move the buildroot Source Tree and create the archive directory
mv misc/buildroot .
Make the archive directory:
mkdir archive
The <nuttx-dir>/../buildroot is where the toolchain is built;
The <nuttx-dir>/../archive directory is where toolchain sources will be downloaded.
3. Make sure that NuttX is configured
cd <nuttx-dir>/tools
./configure.sh <nuttx-configuration>
4. Configure and Make the buildroot
cd buildroot
cp configs/<config-file> .config
make oldconfig
make
This will download the large source packages for the toolchain and build the toolchain.
The resulting binaries will be under buildroot/build_<arch>. There will also be a
large build directory called something like toolchain_build_<arch>; this directory
can be removed once the build completes successfully.
Where <config-file> is one of the configuration files listed above and <arch> is an
archtecture name. Examples: build_m32c, build_arm_nofpu, etc.
Cygwin GCC BUILD NOTES
^^^^^^^^^^^^^^^^^^^^^^
On Cygwin, the buildroot 'make' command will fail with an error like:
"...
build/genchecksum cc1-dummy > cc1-checksum.c
opening cc1-dummy: No such file or directory
..."
This is caused because on Cygwin, host executables will be generated with the extension .exe
and, apparently, the make variable "exeext" is set incorrectly. A work around after the
above occurs is:
cd toolchain_build_<arch>/gcc-4.2.4-build/gcc # Go to the directory where error occurred
mv cc1-dummy.exe cc1-dummy # Rename the executable without .exe
rm cc1-checksum.c # Get rid of the bad generated file
Then resume the buildroot make:
cd - # Back to the buildroot make directory
make # Restart the build
If you build g++, you will see another similar error:
...
build/genchecksum cc1plus-dummy > cc1plus-checksum.c
opening cc1plus-dummy: No such file or directory
...
The fix is similar:
cd toolchain_build_<arch>/gcc-4.2.4-build/gcc # Go to the directory where error occurred
mv cc1plus-dummy.exe cc1plus-dummy # Rename the executable without .exe
rm cc1plus-checksum.c # Get rid of the bad generated file
Then resume the buildroot make:
cd - # Back to the buildroot make directory
make # Restart the build
|