1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
/****************************************************************************************************
* configs/freedom-kl25z/src/freedom-kl25z.h
* arch/arm/src/board/freedom-kl25z.c
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************************************/
#ifndef __CONFIGS_NUTINY_NUC120_SRC_NUTINY_NUC120_H
#define __CONFIGS_NUTINY_NUC120_SRC_NUTINY_NUC120_H
/****************************************************************************************************
* Included Files
****************************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************************************
* Definitions
****************************************************************************************************/
/* Configuration ************************************************************************************/
/* NuTiny-EVB-120 GPIOs *****************************************************************************/
/* The NuTiny has a single green LED that can be controlled from sofware. This LED
* is connected to PIN17 (PB.0). It is pulled high so a low value will illuminate the LED.
*
* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board the
* NuTiny. The following definitions describe how NuttX controls the LEDs:
*
* SYMBOL Meaning LED state
* Initially all LED is OFF
* ------------------- ----------------------- ------------- ------------
* LED_STARTED NuttX has been started LED ON
* LED_HEAPALLOCATE Heap has been allocated LED ON
* LED_IRQSENABLED Interrupts enabled LED ON
* LED_STACKCREATED Idle stack created LED ON
* LED_INIRQ In an interrupt LED should glow
* LED_SIGNAL In a signal handler LED might glow
* LED_ASSERTION An assertion failed LED ON while handling the assertion
* LED_PANIC The system has crashed LED Blinking at 2Hz
* LED_IDLE NUC1XX is in sleep mode (Optional, not used)
*/
#define GPIO_LED (GPIO_OUTPUT | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN0)
/* Button definitions ***************************************************************/
/* The NuTiny has no buttons */
/****************************************************************************************************
* Public Types
****************************************************************************************************/
/****************************************************************************************************
* Public data
****************************************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************************************
* Public Functions
****************************************************************************************************/
/****************************************************************************************************
* Name: kl_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the NuTiny-EVB-120 board.
*
****************************************************************************************************/
void weak_function kl_spiinitialize(void);
/****************************************************************************************************
* Name: kl_usbinitialize
*
* Description:
* Called from kl_usbinitialize very early in inialization to setup USB-related
* GPIO pins for the NuTiny-EVB-120 board.
*
****************************************************************************************************/
#ifdef CONFIG_STM32_USB
void weak_function kl_usbinitialize(void);
#endif
/****************************************************************************************************
* Name: kl_ledinit
*
* Description:
* Initialize the on-board LED
*
****************************************************************************************************/
#ifdef CONFIG_ARCH_LEDS
void kl_ledinit(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_NUTINY_NUC120_SRC_NUTINY_NUC120_H */
|
