1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
|
/**************************************************************************************
* drivers/lcd/st7567.h
*
* Definitions for the ST7567 128x64 Dot Matrix LCD
* Driver with C
*
* Copyright (C) 2013 Zilogic Systems. All rights reserved.
* Author: Manikandan <code@zilogic.com>
*
* Based on drivers/lcd/ssd1305.h
*
* Copyright (C) 2010 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* References: SSD1305.pdf, "Solomon Systech SSD1305 136x64 Dot Matrix OLED/PLED
* Segment/Common Driver with Controller," Solomon Systech Limited,
* http://www.solomon-systech.com, May, 2008.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
**************************************************************************************/
#ifndef __DRIVERS_LCD_ST7567_H
#define __DRIVERS_LCD_ST7567_H
/**************************************************************************************
* Included Files
**************************************************************************************/
/**************************************************************************************
* Pre-processor Definitions
**************************************************************************************/
/* Fundamental Commands *****************************************************/
#define ST7567_DISPOFF 0xae /* 0xae: Display OFF (sleep mode) */
#define ST7567_DISPON 0xaf /* 0xaf: Display ON in normal mode */
#define ST7567_SETSTARTLINE 0x40 /* 0x40-7f: Set display start line */
# define ST7567_STARTLINE_MASK 0x3f
#define ST7567_SETPAGESTART 0xb0 /* 0xb0-b7: Set page start address */
# define ST7567_PAGESTART_MASK 0x07
#define ST7567_SETCOLL 0x00 /* 0x00-0x0f: Set lower column address */
# define ST7567_COLL_MASK 0x0f
#define ST7567_SETCOLH 0x10 /* 0x10-0x1f: Set higher column address */
# define ST7567_COLH_MASK 0x0f
#define SSD1305_MAPCOL0 0xa0 /* 0xa0: Column address 0 is mapped to SEG0 */
#define SSD1305_MAPCOL128 0xa1 /* 0xa1: Column address 128 is mapped to SEG0 */
#define ST7567_DISPNORMAL 0xa6 /* 0xa6: Normal display */
#define ST7567_DISPINVERSE 0xa7 /* 0xa7: Inverse display */
#define ST7567_DISPRAM 0xa4 /* 0xa4: Resume to RAM content display */
#define ST7567_DISPENTIRE 0xa5 /* 0xa5: Entire display ON */
#define ST7567_BIAS_1_9 0xa2 /* 0xa2: Select BIAS setting 1/9 */
#define ST7567_BIAS_1_7 0xa3 /* 0xa3: Select BIAS setting 1/7 */
#define ST7567_ENTER_RMWMODE 0xe0 /* 0xe0: Enter the Read Modify Write mode */
#define ST7567_EXIT_RMWMODE 0xee /* 0xee: Leave the Read Modify Write mode */
#define ST7567_EXIT_SOFTRST 0xe2 /* 0xe2: Software RESET */
#define ST7567_SETCOMNORMAL 0xc0 /* 0xc0: Set COM output direction, normal mode */
#define ST7567_SETCOMREVERSE 0xc8 /* 0xc8: Set COM output direction, reverse mode */
#define ST7567_POWERCTRL_VF 0x29 /* 0x29: Control built-in power circuit */
#define ST7567_POWERCTRL_VR 0x2a /* 0x2a: Control built-in power circuit */
#define ST7567_POWERCTRL_VB 0x2c /* 0x2c: Control built-in power circuit */
#define ST7567_POWERCTRL 0x2f /* 0x2c: Control built-in power circuit */
#define ST7567_REG_RES_RR0 0x21 /* 0x21: Regulation Resistior ratio */
#define ST7567_REG_RES_RR1 0x22 /* 0x22: Regulation Resistior ratio */
#define ST7567_REG_RES_RR2 0x24 /* 0x24: Regulation Resistior ratio */
#define ST7567_SETEV 0x81 /* 0x81: Set contrast control */
#define ST7567_SETBOOSTER 0xf8 /* Set booster level */
#define ST7567_SETBOOSTER4X 0x00 /* Set booster level */
#define ST7567_SETBOOSTER5X 0x01 /* Set booster level */
#define ST7567_NOP 0xe3 /* 0xe3: NOP Command for no operation */
#endif /* __DRIVERS_LCD_ST7567_H */
|
