blob: 0c0cfa53d34a7273d48e157aa3ca18ebcf6c8c41 (
plain) (
tree)
|
|
#!nsh
#
# Load default params for this platform
#
if param compare SYS_AUTOCONFIG 1
then
# Set all params here, then disable autoconfig
param set SYS_AUTOCONFIG 0
param set MC_ATTRATE_D 0.002
param set MC_ATTRATE_I 0.0
param set MC_ATTRATE_P 0.09
param set MC_ATT_D 0.0
param set MC_ATT_I 0.0
param set MC_ATT_P 6.8
param set MC_YAWPOS_D 0.0
param set MC_YAWPOS_I 0.0
param set MC_YAWPOS_P 2.0
param set MC_YAWRATE_D 0.005
param set MC_YAWRATE_I 0.2
param set MC_YAWRATE_P 0.3
param set NAV_TAKEOFF_ALT 3.0
param set MPC_TILT_MAX 0.5
param set MPC_THR_MAX 0.7
param set MPC_THR_MIN 0.3
param set MPC_XY_D 0
param set MPC_XY_P 0.5
param set MPC_XY_VEL_D 0
param set MPC_XY_VEL_I 0
param set MPC_XY_VEL_MAX 3
param set MPC_XY_VEL_P 0.2
param set MPC_Z_D 0
param set MPC_Z_P 1
param set MPC_Z_VEL_D 0
param set MPC_Z_VEL_I 0.1
param set MPC_Z_VEL_MAX 2
param set MPC_Z_VEL_P 0.20
param save
fi
echo "RC script for PX4FMU + PX4IO + PPM-ESCs running"
#
# Force some key parameters to sane values
# MAV_TYPE 2 = quadrotor
#
param set MAV_TYPE 2
set EXIT_ON_END no
usleep 10000
#
# Start and configure PX4IO or FMU interface
#
if px4io detect
then
# Start MAVLink (depends on orb)
mavlink start -d /dev/ttyS1 -b 57600
usleep 5000
commander start
sh /etc/init.d/rc.io
else
fmu mode_pwm
# Start MAVLink (on UART1 / ttyS0)
mavlink start -d /dev/ttyS1 -b 57600
usleep 5000
param set BAT_V_SCALING 0.004593
set EXIT_ON_END yes
fi
if [ $ESC_MAKER = afro ]
then
# Set PWM values for Afro ESCs
pwm disarmed -c 1234 -p 1050
pwm min -c 1234 -p 1080
pwm max -c 1234 -p 1860
else
# Set PWM values for typical ESCs
pwm disarmed -c 1234 -p 900
pwm min -c 1234 -p 980
pwm max -c 1234 -p 1800
fi
#
# Load mixer
#
if [ $FRAME_GEOMETRY == x ]
then
echo "Frame geometry X"
mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix
else
if [ $FRAME_GEOMETRY == w ]
then
echo "Frame geometry W"
mixer load /dev/pwm_output /etc/mixers/FMU_quad_w.mix
else
echo "Frame geometry +"
mixer load /dev/pwm_output /etc/mixers/FMU_quad_+.mix
fi
fi
#
# Set PWM output frequency
#
pwm rate -r 400 -c 1234
#
# Start common for all multirotors apps
#
sh /etc/init.d/rc.multirotor
if [ $EXIT_ON_END == yes ]
then
exit
fi
echo "Script end"
|