/************************************************************************************
* configs/px4fmu/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2009 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_BOARD_BOARD_H
#define __ARCH_BOARD_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* The PX4FMU uses a 24MHz crystal connected to the HSE.
*
* This is the "standard" configuration as set up by arch/arm/src/stm32f40xx_rcc.c:
* System Clock source : PLL (HSE)
* SYSCLK(Hz) : 168000000 Determined by PLL configuration
* HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE)
* AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE)
* APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1)
* APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2)
* HSE Frequency(Hz) : 24000000 (STM32_BOARD_XTAL)
* PLLM : 24 (STM32_PLLCFG_PLLM)
* PLLN : 336 (STM32_PLLCFG_PLLN)
* PLLP : 2 (STM32_PLLCFG_PLLP)
* PLLQ : 7 (STM32_PLLCFG_PPQ)
* Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK
* Flash Latency(WS) : 5
* Prefetch Buffer : OFF
* Instruction cache : ON
* Data cache : ON
* Require 48MHz for USB OTG FS, : Enabled
* SDIO and RNG clock
*/
/* HSI - 16 MHz RC factory-trimmed
* LSI - 32 KHz RC
* HSE - On-board crystal frequency is 24MHz
* LSE - not installed
*/
#define STM32_BOARD_XTAL 24000000ul
#define STM32_HSI_FREQUENCY 16000000ul
#define STM32_LSI_FREQUENCY 32000
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
//#define STM32_LSE_FREQUENCY 32768
/* Main PLL Configuration.
*
* PLL source is HSE
* PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
* = (25,000,000 / 25) * 336
* = 336,000,000
* SYSCLK = PLL_VCO / PLLP
* = 336,000,000 / 2 = 168,000,000
* USB OTG FS, SDIO and RNG Clock
* = PLL_VCO / PLLQ
* = 48,000,000
*/
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(24)
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336)
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7)
#define STM32_SYSCLK_FREQUENCY 168000000ul
/* AHB clock (HCLK) is SYSCLK (168MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4)
/* Timers driven from APB1 will be twice PCLK1 */
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY)
/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2)
/* Timers driven from APB2 will be twice PCLK2 */
#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK1_FREQUENCY)
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
* otherwise frequency is 2xAPBx.
* Note: TIM1,8 are on APB2, others on APB1
*/
#define STM32_TIM18_FREQUENCY (2*STM32_PCLK2_FREQUENCY)
#define STM32_TIM27_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
* in order to avoid RX overrun/TX underrun errors due to delayed responses
* to service FIFOs in interrupt driven mode. These values have not been
* tuned!!!
*
* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
*/
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
*/
#ifdef CONFIG_SDIO_DMA
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
#else
# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
#endif
/* High-resolution timer
*/
#ifdef CONFIG_HRT_TIMER
# define HRT_TIMER 1 /* use timer1 for the HRT */
# define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */
#endif
/* LED definitions ******************************************************************/
/* PX4 has two LEDs that we will encode as: */
#define LED_STARTED 0 /* LED? */
#define LED_HEAPALLOCATE 1 /* LED? */
#define LED_IRQSENABLED 2 /* LED? + LED? */
#define LED_STACKCREATED 3 /* LED? */
#define LED_INIRQ 4 /* LED? + LED? */
#define LED_SIGNAL 5 /* LED? + LED? */
#define LED_ASSERTION 6 /* LED? + LED? + LED? */
#define LED_PANIC 7 /* N/C + N/C + N/C + LED? */
/* Alternate function pin selections ************************************************/
/*
* UARTs.
*
* Note that UART5 has no optional pinout.
*/
#define GPIO_USART1_RX GPIO_USART1_RX_2
#define GPIO_USART1_TX GPIO_USART1_TX_2
#define GPIO_USART2_RX GPIO_USART2_RX_1
#define GPIO_USART2_TX GPIO_USART2_TX_1
#define GPIO_USART2_RTS GPIO_USART2_RTS_1
#define GPIO_USART2_CTS GPIO_USART2_CTS_1
#define GPIO_USART6_RX GPIO_USART6_RX_1
#define GPIO_USART6_TX GPIO_USART6_TX_1
/* UART DMA configuration for USART1/6 */
#define DMAMAP_USART1_RX DMAMAP_USART1_RX_2
#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2
/*
* PWM
*
* Four PWM outputs can be configured on pins otherwise shared with
* USART2; two can take the flow control pins if they are not being used.
*
* Pins:
*
* CTS - PA0 - TIM2CH1
* RTS - PA1 - TIM2CH2
* TX - PA2 - TIM2CH3
* RX - PA3 - TIM2CH4
*
*/
#define GPIO_TIM2_CH1OUT GPIO_TIM2_CH1OUT_1
#define GPIO_TIM2_CH2OUT GPIO_TIM2_CH2OUT_1
#define GPIO_TIM2_CH3OUT GPIO_TIM2_CH3OUT_1
#define GPIO_TIM2_CH4OUT GPIO_TIM2_CH4OUT_1
/*
* PPM
*
* PPM input is handled by the HRT timer.
*/
#if defined(CONFIG_HRT_TIMER) && defined (CONFIG_HRT_PPM)
# define HRT_PPM_CHANNEL 3 /* use capture/compare channel 3 */
# define GPIO_PPM_IN (GPIO_ALT|GPIO_AF1|GPIO_SPEED_50MHz|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN10)
#endif
/*
* CAN
*
* CAN2 is routed to the expansion connector.
*/
#define GPIO_CAN2_RX GPIO_CAN2_RX_2
#define GPIO_CAN2_TX GPIO_CAN2_TX_2
/*
* I2C
*
* The optional _GPIO configurations allow the I2C driver to manually
* reset the bus to clear stuck slaves. They match the pin configuration,
* but are normally-high GPIOs.
*/
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2
#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8)
#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1
#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1
#define GPIO_I2C2_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN10)
#define GPIO_I2C2_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN11)
#define GPIO_I2C3_SCL GPIO_I2C3_SCL_1
#define GPIO_I2C3_SDA GPIO_I2C3_SDA_1
#define GPIO_I2C3_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN8)
#define GPIO_I2C3_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN9)
/*
* I2C busses
*/
#define PX4_I2C_BUS_ESC 1
#define PX4_I2C_BUS_ONBOARD 2
#define PX4_I2C_BUS_EXPANSION 3
/*
* Devices on the onboard bus.
*
* Note that these are unshifted addresses.
*/
#define PX4_I2C_OBDEV_HMC5883 0x1e
#define PX4_I2C_OBDEV_MS5611 0x76
#define PX4_I2C_OBDEV_EEPROM NOTDEFINED
#define PX4_I2C_OBDEV_PX4IO_BL 0x18
#define PX4_I2C_OBDEV_PX4IO 0x1a
/*
* SPI
*/
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_2
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_2
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2
#define GPIO_SPI3_MISO GPIO_SPI3_MISO_2
#define GPIO_SPI3_MOSI GPIO_SPI3_MOSI_1
#define GPIO_SPI3_SCK GPIO_SPI3_SCK_2
#define GPIO_SPI3_NSS GPIO_SPI3_NSS_2
/*
* Use these in place of the spi_dev_e enumeration to
* select a specific SPI device on SPI1
*/
#define PX4_SPIDEV_GYRO 1
#define PX4_SPIDEV_ACCEL 2
#define PX4_SPIDEV_MPU 3
#define PX4_SPIDEV_ACCEL_MAG 2 // external for anti vibration test
/*
* Tone alarm output
*/
#define TONE_ALARM_TIMER 3 /* timer 3 */
#define TONE_ALARM_CHANNEL 3 /* channel 3 */
#define GPIO_TONE_ALARM_IDLE (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN8)
#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF2|GPIO_SPEED_2MHz|GPIO_FLOAT|GPIO_PUSHPULL|GPIO_PORTC|GPIO_PIN8)
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
EXTERN void stm32_boardinitialize(void);
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_BOARD_BOARD_H */