|
|
/****************************************************************************
*
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file board_config.h
*
* PX4FMUv1 internal definitions
*/
#pragma once
/****************************************************************************************************
* Included Files
****************************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
__BEGIN_DECLS
/* these headers are not C++ safe */
#include <stm32.h>
#include <arch/board/board.h>
/****************************************************************************************************
* Definitions
****************************************************************************************************/
/* Configuration ************************************************************************************/
/* PX4IO connection configuration */
#define PX4IO_SERIAL_DEVICE "/dev/ttyS2"
#define UDID_START 0x1FFF7A10
//#ifdef CONFIG_STM32_SPI2
//# error "SPI2 is not supported on this board"
//#endif
#if defined(CONFIG_STM32_CAN1)
# warning "CAN1 is not supported on this board"
#endif
/* PX4FMU GPIOs ***********************************************************************************/
/* LEDs */
#define GPIO_LED1 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN15)
#define GPIO_LED2 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN14)
/* External interrupts */
#define GPIO_EXTI_COMPASS (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN1)
/* SPI chip selects */
#define GPIO_SPI_CS_GYRO (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN14)
#define GPIO_SPI_CS_ACCEL (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN15)
#define GPIO_SPI_CS_MPU (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN0)
#define GPIO_SPI_CS_SDCARD (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define PX4_SPI_BUS_SENSORS 1
/*
* Use these in place of the spi_dev_e enumeration to
* select a specific SPI device on SPI1
*/
#define PX4_SPIDEV_GYRO 1
#define PX4_SPIDEV_ACCEL 2
#define PX4_SPIDEV_MPU 3
/*
* Optional devices on IO's external port
*/
#define PX4_SPIDEV_ACCEL_MAG 2
/*
* I2C busses
*/
#define PX4_I2C_BUS_ESC 1
#define PX4_I2C_BUS_ONBOARD 2
#define PX4_I2C_BUS_EXPANSION 3
#define PX4_I2C_BUS_LED 3
/*
* Devices on the onboard bus.
*
* Note that these are unshifted addresses.
*/
#define PX4_I2C_OBDEV_HMC5883 0x1e
#define PX4_I2C_OBDEV_MS5611 0x76
#define PX4_I2C_OBDEV_EEPROM NOTDEFINED
#define PX4_I2C_OBDEV_LED 0x55
#define PX4_I2C_OBDEV_PX4IO_BL 0x18
#define PX4_I2C_OBDEV_PX4IO 0x1a
/* User GPIOs
*
* GPIO0-1 are the buffered high-power GPIOs.
* GPIO2-5 are the USART2 pins.
* GPIO6-7 are the CAN2 pins.
*/
#define GPIO_GPIO0_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN4)
#define GPIO_GPIO1_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN5)
#define GPIO_GPIO2_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN0)
#define GPIO_GPIO3_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN1)
#define GPIO_GPIO4_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN2)
#define GPIO_GPIO5_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN3)
#define GPIO_GPIO6_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN13)
#define GPIO_GPIO7_INPUT (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN2)
#define GPIO_GPIO0_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN4)
#define GPIO_GPIO1_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN5)
#define GPIO_GPIO2_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN0)
#define GPIO_GPIO3_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN1)
#define GPIO_GPIO4_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN2)
#define GPIO_GPIO5_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN3)
#define GPIO_GPIO6_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN13)
#define GPIO_GPIO7_OUTPUT (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN12)
#define GPIO_GPIO_DIR (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13)
/*
* Tone alarm output
*/
#define TONE_ALARM_TIMER 3 /* timer 3 */
#define TONE_ALARM_CHANNEL 3 /* channel 3 */
#define GPIO_TONE_ALARM_IDLE (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN8)
#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF2|GPIO_SPEED_2MHz|GPIO_FLOAT|GPIO_PUSHPULL|GPIO_PORTC|GPIO_PIN8)
/*
* PWM
*
* Four PWM outputs can be configured on pins otherwise shared with
* USART2; two can take the flow control pins if they are not being used.
*
* Pins:
*
* CTS - PA0 - TIM2CH1
* RTS - PA1 - TIM2CH2
* TX - PA2 - TIM2CH3
* RX - PA3 - TIM2CH4
*
*/
#define GPIO_TIM2_CH1OUT GPIO_TIM2_CH1OUT_1
#define GPIO_TIM2_CH2OUT GPIO_TIM2_CH2OUT_1
#define GPIO_TIM2_CH3OUT GPIO_TIM2_CH3OUT_1
#define GPIO_TIM2_CH4OUT GPIO_TIM2_CH4OUT_1
/* USB OTG FS
*
* PA9 OTG_FS_VBUS VBUS sensing (also connected to the green LED)
*/
#define GPIO_OTGFS_VBUS (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|GPIO_OPENDRAIN|GPIO_PORTA|GPIO_PIN9)
/* High-resolution timer
*/
#define HRT_TIMER 1 /* use timer1 for the HRT */
#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */
#define HRT_PPM_CHANNEL 3 /* use capture/compare channel 3 */
#define GPIO_PPM_IN (GPIO_ALT|GPIO_AF1|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN10)
/****************************************************************************************************
* Public Types
****************************************************************************************************/
/****************************************************************************************************
* Public data
****************************************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************************************
* Public Functions
****************************************************************************************************/
/****************************************************************************************************
* Name: stm32_spiinitialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the PX4FMU board.
*
****************************************************************************************************/
extern void stm32_spiinitialize(void);
extern void stm32_usbinitialize(void);
/****************************************************************************
* Name: nsh_archinitialize
*
* Description:
* Perform architecture specific initialization for NSH.
*
* CONFIG_NSH_ARCHINIT=y :
* Called from the NSH library
*
* CONFIG_BOARD_INITIALIZE=y, CONFIG_NSH_LIBRARY=y, &&
* CONFIG_NSH_ARCHINIT=n :
* Called from board_initialize().
*
****************************************************************************/
#ifdef CONFIG_NSH_LIBRARY
int nsh_archinitialize(void);
#endif
#endif /* __ASSEMBLY__ */
__END_DECLS
|