/****************************************************************************
*
* Copyright (C) 2013 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file gyro_calibration.cpp
*
* Gyroscope calibration routine
*/
#include "gyro_calibration.h"
#include "calibration_messages.h"
#include "commander_helper.h"
#include <stdio.h>
#include <fcntl.h>
#include <poll.h>
#include <math.h>
#include <drivers/drv_hrt.h>
#include <uORB/topics/sensor_combined.h>
#include <drivers/drv_gyro.h>
#include <mavlink/mavlink_log.h>
#include <systemlib/param/param.h>
#include <systemlib/err.h>
/* oddly, ERROR is not defined for c++ */
#ifdef ERROR
# undef ERROR
#endif
static const int ERROR = -1;
static const char *sensor_name = "gyro";
int do_gyro_calibration(int mavlink_fd)
{
mavlink_log_info(mavlink_fd, CAL_STARTED_MSG, sensor_name);
mavlink_log_info(mavlink_fd, "don't move system");
struct gyro_scale gyro_scale = {
0.0f,
1.0f,
0.0f,
1.0f,
0.0f,
1.0f,
};
int res = OK;
/* reset all offsets to zero and all scales to one */
int fd = open(GYRO_DEVICE_PATH, 0);
res = ioctl(fd, GYROIOCSSCALE, (long unsigned int)&gyro_scale);
close(fd);
if (res != OK) {
mavlink_log_critical(mavlink_fd, CAL_FAILED_RESET_CAL_MSG);
}
if (res == OK) {
/* determine gyro mean values */
const unsigned calibration_count = 5000;
unsigned calibration_counter = 0;
unsigned poll_errcount = 0;
/* subscribe to gyro sensor topic */
int sub_sensor_gyro = orb_subscribe(ORB_ID(sensor_gyro));
struct gyro_report gyro_report;
while (calibration_counter < calibration_count) {
/* wait blocking for new data */
struct pollfd fds[1];
fds[0].fd = sub_sensor_gyro;
fds[0].events = POLLIN;
int poll_ret = poll(fds, 1, 1000);
if (poll_ret > 0) {
orb_copy(ORB_ID(sensor_gyro), sub_sensor_gyro, &gyro_report);
gyro_scale.x_offset += gyro_report.x;
gyro_scale.y_offset += gyro_report.y;
gyro_scale.z_offset += gyro_report.z;
calibration_counter++;
if (calibration_counter % (calibration_count / 20) == 0)
mavlink_log_info(mavlink_fd, CAL_PROGRESS_MSG, sensor_name, (calibration_counter * 100) / calibration_count);
} else {
poll_errcount++;
}
if (poll_errcount > 1000) {
mavlink_log_critical(mavlink_fd, CAL_FAILED_SENSOR_MSG);
res = ERROR;
break;
}
}
close(sub_sensor_gyro);
gyro_scale.x_offset /= calibration_count;
gyro_scale.y_offset /= calibration_count;
gyro_scale.z_offset /= calibration_count;
}
if (res == OK) {
/* check offsets */
if (!isfinite(gyro_scale.x_offset) || !isfinite(gyro_scale.y_offset) || !isfinite(gyro_scale.z_offset)) {
mavlink_log_critical(mavlink_fd, "ERROR: offset is NaN");
res = ERROR;
}
}
if (res == OK) {
/* set offset parameters to new values */
if (param_set(param_find("SENS_GYRO_XOFF"), &(gyro_scale.x_offset))
|| param_set(param_find("SENS_GYRO_YOFF"), &(gyro_scale.y_offset))
|| param_set(param_find("SENS_GYRO_ZOFF"), &(gyro_scale.z_offset))) {
mavlink_log_critical(mavlink_fd, "ERROR: failed to set offset params");
res = ERROR;
}
}
#if 0
/* beep on offset calibration end */
mavlink_log_info(mavlink_fd, "gyro offset calibration done");
tune_neutral();
/* scale calibration */
/* this was only a proof of concept and is currently not working. scaling will be set to 1.0 for now. */
mavlink_log_info(mavlink_fd, "offset done. Rotate for scale 30x or wait 5s to skip.");
warnx("offset calibration finished. Rotate for scale 30x, or do not rotate and wait for 5 seconds to skip.");
/* apply new offsets */
fd = open(GYRO_DEVICE_PATH, 0);
if (OK != ioctl(fd, GYROIOCSSCALE, (long unsigned int)&gyro_scale))
warn("WARNING: failed to apply new offsets for gyro");
close(fd);
unsigned rotations_count = 30;
float gyro_integral = 0.0f;
float baseline_integral = 0.0f;
// XXX change to mag topic
orb_copy(ORB_ID(sensor_combined), sub_sensor_combined, &raw);
float mag_last = -atan2f(raw.magnetometer_ga[1], raw.magnetometer_ga[0]);
if (mag_last > M_PI_F) mag_last -= 2 * M_PI_F;
if (mag_last < -M_PI_F) mag_last += 2 * M_PI_F;
uint64_t last_time = hrt_absolute_time();
uint64_t start_time = hrt_absolute_time();
while ((int)fabsf(baseline_integral / (2.0f * M_PI_F)) < rotations_count) {
/* abort this loop if not rotated more than 180 degrees within 5 seconds */
if ((fabsf(baseline_integral / (2.0f * M_PI_F)) < 0.6f)
&& (hrt_absolute_time() - start_time > 5 * 1e6)) {
mavlink_log_info(mavlink_fd, "scale skipped, gyro calibration done");
close(sub_sensor_combined);
return OK;
}
/* wait blocking for new data */
struct pollfd fds[1];
fds[0].fd = sub_sensor_combined;
fds[0].events = POLLIN;
int poll_ret = poll(fds, 1, 1000);
if (poll_ret) {
float dt_ms = (hrt_absolute_time() - last_time) / 1e3f;
last_time = hrt_absolute_time();
orb_copy(ORB_ID(sensor_combined), sub_sensor_combined, &raw);
// XXX this is just a proof of concept and needs world / body
// transformation and more
//math::Vector2f magNav(raw.magnetometer_ga);
// calculate error between estimate and measurement
// apply declination correction for true heading as well.
//float mag = -atan2f(magNav(1),magNav(0));
float mag = -atan2f(raw.magnetometer_ga[1], raw.magnetometer_ga[0]);
if (mag > M_PI_F) mag -= 2 * M_PI_F;
if (mag < -M_PI_F) mag += 2 * M_PI_F;
float diff = mag - mag_last;
if (diff > M_PI_F) diff -= 2 * M_PI_F;
if (diff < -M_PI_F) diff += 2 * M_PI_F;
baseline_integral += diff;
mag_last = mag;
// Jump through some timing scale hoops to avoid
// operating near the 1e6/1e8 max sane resolution of float.
gyro_integral += (raw.gyro_rad_s[2] * dt_ms) / 1e3f;
// warnx("dbg: b: %6.4f, g: %6.4f", (double)baseline_integral, (double)gyro_integral);
// } else if (poll_ret == 0) {
// /* any poll failure for 1s is a reason to abort */
// mavlink_log_info(mavlink_fd, "gyro calibration aborted, retry");
// return;
}
}
float gyro_scale = baseline_integral / gyro_integral;
warnx("gyro scale: yaw (z): %6.4f", (double)gyro_scale);
mavlink_log_info(mavlink_fd, "gyro scale: yaw (z): %6.4f", (double)gyro_scale);
if (!isfinite(gyro_scale.x_scale) || !isfinite(gyro_scale.y_scale) || !isfinite(gyro_scale.z_scale)) {
mavlink_log_info(mavlink_fd, "gyro scale calibration FAILED (NaN)");
close(sub_sensor_gyro);
mavlink_log_critical(mavlink_fd, "gyro calibration failed");
return ERROR;
}
/* beep on calibration end */
mavlink_log_info(mavlink_fd, "gyro scale calibration done");
tune_neutral();
#endif
if (res == OK) {
/* set scale parameters to new values */
if (param_set(param_find("SENS_GYRO_XSCALE"), &(gyro_scale.x_scale))
|| param_set(param_find("SENS_GYRO_YSCALE"), &(gyro_scale.y_scale))
|| param_set(param_find("SENS_GYRO_ZSCALE"), &(gyro_scale.z_scale))) {
mavlink_log_critical(mavlink_fd, "ERROR: failed to set scale params");
res = ERROR;
}
}
if (res == OK) {
/* apply new scaling and offsets */
fd = open(GYRO_DEVICE_PATH, 0);
res = ioctl(fd, GYROIOCSSCALE, (long unsigned int)&gyro_scale);
close(fd);
if (res != OK) {
mavlink_log_critical(mavlink_fd, CAL_FAILED_APPLY_CAL_MSG);
}
}
if (res == OK) {
/* auto-save to EEPROM */
res = param_save_default();
if (res != OK) {
mavlink_log_critical(mavlink_fd, CAL_FAILED_SAVE_PARAMS_MSG);
}
}
if (res == OK) {
mavlink_log_info(mavlink_fd, CAL_DONE_MSG, sensor_name);
} else {
mavlink_log_info(mavlink_fd, CAL_FAILED_MSG, sensor_name);
}
return res;
}