diff options
author | Jean Cyr <jcyr@dillobits.com> | 2013-07-05 20:51:29 -0400 |
---|---|---|
committer | Jean Cyr <jcyr@dillobits.com> | 2013-07-05 20:51:29 -0400 |
commit | 3f9f2018e20f4be23e7d62571ec0a3678d960108 (patch) | |
tree | 59f0a2cf6c7bc802d95fcc31143caa26353190a3 /src/drivers/px4io | |
parent | 697c0a1a1d7fb1043786533da3570f28acd661dc (diff) | |
download | px4-firmware-3f9f2018e20f4be23e7d62571ec0a3678d960108.tar.gz px4-firmware-3f9f2018e20f4be23e7d62571ec0a3678d960108.tar.bz2 px4-firmware-3f9f2018e20f4be23e7d62571ec0a3678d960108.zip |
Support binding DSM2 and DSMX satellite receivers
The px4io bind command allows you to put a DSM satellite receiver into
bind mode. Since this feature requires that
the dsm VCC line (red wire) be cut and routed through relay one, it is
not enabled by default in order not to
affect those not using a DSM satellite receiver or wising to use relay
one for other purposes.
NOTE: Binding DSM2 satellites in 11-bit mode is not supported due to
potential bug in some DSM2 receiver streams
when in 11-bit mode. Furthermore the px4io software folds 11 bit data
down to 10 bits so there is no resolution
advantage to to 11-bit mode.
To enable the feature the RC_RL1_DSM_VCC parameter must be set to a non
zero value from the console, or using
QGroundControl:
param set RC_RL1_DSM_VCC 1
From the console you can initiate DSM bind mode with:
uorb start
param set RC_RL1_DSM_VCC 1
px4io start
px4io bind dsm2
For binding a DSMX satellite to a DSMX transmitter you would instead
use:
px4io bind dsmx
Your receiver module should start a rapid flash and you can follow the
normal binding sequence of your
transmitter.
Note: The value of parameter RC_RL1_DSM_VCC defaults to 0, so none of
this will have any effect on an unmodified
DSM receiver connection. For this feature to work, the power wire (red)
must be cut and each side connected to a
terminal on relay1 of the px4io board.
This has been tested using Spektrum as well as Hobby King 'Orange' DSM
satellite receivers.
Both px4fmu and px4io images are updated.
Diffstat (limited to 'src/drivers/px4io')
-rw-r--r-- | src/drivers/px4io/px4io.cpp | 96 |
1 files changed, 91 insertions, 5 deletions
diff --git a/src/drivers/px4io/px4io.cpp b/src/drivers/px4io/px4io.cpp index 19163cebe..54b9d50e4 100644 --- a/src/drivers/px4io/px4io.cpp +++ b/src/drivers/px4io/px4io.cpp @@ -89,6 +89,8 @@ #define PX4IO_SET_DEBUG _IOC(0xff00, 0) #define PX4IO_INAIR_RESTART_ENABLE _IOC(0xff00, 1) +static int dsm_vcc_ctl; + class PX4IO : public device::I2C { public: @@ -700,8 +702,6 @@ PX4IO::io_set_control_state() int PX4IO::set_failsafe_values(const uint16_t *vals, unsigned len) { - uint16_t regs[_max_actuators]; - if (len > _max_actuators) /* fail with error */ return E2BIG; @@ -1271,13 +1271,14 @@ PX4IO::print_status() printf("%u bytes free\n", io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FREEMEM)); uint16_t flags = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FLAGS); - printf("status 0x%04x%s%s%s%s%s%s%s%s%s%s%s%s\n", + printf("status 0x%04x%s%s%s%s%s%s%s%s%s%s%s%s%s\n", flags, ((flags & PX4IO_P_STATUS_FLAGS_ARMED) ? " ARMED" : ""), ((flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) ? " OVERRIDE" : ""), ((flags & PX4IO_P_STATUS_FLAGS_RC_OK) ? " RC_OK" : " RC_FAIL"), ((flags & PX4IO_P_STATUS_FLAGS_RC_PPM) ? " PPM" : ""), - ((flags & PX4IO_P_STATUS_FLAGS_RC_DSM) ? " DSM" : ""), + (((flags & PX4IO_P_STATUS_FLAGS_RC_DSM) && (!(flags & PX4IO_P_STATUS_FLAGS_RC_DSM11))) ? " DSM10" : ""), + (((flags & PX4IO_P_STATUS_FLAGS_RC_DSM) && (flags & PX4IO_P_STATUS_FLAGS_RC_DSM11)) ? " DSM11" : ""), ((flags & PX4IO_P_STATUS_FLAGS_RC_SBUS) ? " SBUS" : ""), ((flags & PX4IO_P_STATUS_FLAGS_FMU_OK) ? " FMU_OK" : " FMU_FAIL"), ((flags & PX4IO_P_STATUS_FLAGS_RAW_PWM) ? " RAW_PPM" : ""), @@ -1424,6 +1425,26 @@ PX4IO::ioctl(file *filep, int cmd, unsigned long arg) *(unsigned *)arg = _max_actuators; break; + case DSM_BIND_START: + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_power_down); + usleep(500000); + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_set_rx_out); + usleep(1000); + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_power_up); + usleep(100000); + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_send_pulses | (arg << 4)); + break; + + case DSM_BIND_STOP: + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_power_down); + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_reinit_uart); + usleep(500000); + break; + + case DSM_BIND_POWER_UP: + io_reg_set(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_DSM, dsm_bind_power_up); + break; + case PWM_SERVO_SET(0) ... PWM_SERVO_SET(PWM_OUTPUT_MAX_CHANNELS - 1): { /* TODO: we could go lower for e.g. TurboPWM */ @@ -1614,10 +1635,72 @@ start(int argc, char *argv[]) errx(1, "driver init failed"); } + if (param_get(param_find("RC_RL1_DSM_VCC"), &dsm_vcc_ctl) == OK) { + if (dsm_vcc_ctl) { + int fd = open("/dev/px4io", O_WRONLY); + if (fd < 0) + errx(1, "failed to open device"); + ioctl(fd, DSM_BIND_POWER_UP, 0); + close(fd); + } + } exit(0); } void +bind(int argc, char *argv[]) +{ + int fd, pulses; + + if (g_dev == nullptr) + errx(1, "px4io must be started first"); + + if (dsm_vcc_ctl == 0) + errx(1, "DSM bind feature not enabled"); + + if (argc < 3) + errx(0, "needs argument, use dsm2 or dsmx"); + + if (!strcmp(argv[2], "dsm2")) + pulses = 3; + else if (!strcmp(argv[2], "dsmx")) + pulses = 7; + else + errx(1, "unknown parameter %s, use dsm2 or dsmx", argv[2]); + + fd = open("/dev/px4io", O_WRONLY); + + if (fd < 0) + errx(1, "failed to open device"); + + ioctl(fd, DSM_BIND_START, pulses); + + /* Open console directly to grab CTRL-C signal */ + int console = open("/dev/console", O_NONBLOCK | O_RDONLY | O_NOCTTY); + if (!console) + errx(1, "failed opening console"); + + warnx("This command will only bind DSM if satellite VCC (red wire) is controlled by relay 1."); + warnx("Press CTRL-C or 'c' when done."); + + for (;;) { + usleep(500000L); + /* Check if user wants to quit */ + char c; + if (read(console, &c, 1) == 1) { + if (c == 0x03 || c == 0x63) { + warnx("Done\n"); + ioctl(fd, DSM_BIND_STOP, 0); + ioctl(fd, DSM_BIND_POWER_UP, 0); + close(fd); + close(console); + exit(0); + } + } + } +} + +void test(void) { int fd; @@ -1918,6 +2001,9 @@ px4io_main(int argc, char *argv[]) if (!strcmp(argv[1], "monitor")) monitor(); + if (!strcmp(argv[1], "bind")) + bind(argc, argv); + out: - errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug', 'recovery', 'limit', 'current', 'failsafe' or 'update'"); + errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug', 'recovery', 'limit', 'current', 'failsafe', 'bind', or 'update'"); } |