Slightly reworked IO internal failsafe, added command to activate it (px4io failsafe), does not parse commandline arguments yet

4 files changed, 73 insertions, 15 deletions

diff --git a/src/drivers/px4io/px4io.cpp b/src/drivers/px4io/px4io.cpp
index 8b2fae12b..f25d471aa 100644
--- a/src/drivers/px4io/px4io.cpp
+++ b/src/drivers/px4io/px4io.cpp
@@ -106,7 +106,7 @@ public:
 	* @param rate    The rate in Hz actuator outpus are sent to IO.
 	*      Min 10 Hz, max 400 Hz
 	*/
-	int      set_update_rate(int rate);
+	int      		set_update_rate(int rate);
 
 	/**
 	* Set the battery current scaling and bias
@@ -114,7 +114,15 @@ public:
 	* @param amp_per_volt
 	* @param amp_bias
 	*/
-	void      set_battery_current_scaling(float amp_per_volt, float amp_bias);
+	void      		set_battery_current_scaling(float amp_per_volt, float amp_bias);
+
+	/**
+	 * Push failsafe values to IO.
+	 *
+	 * @param vals Failsafe control inputs: in us PPM (900 for zero, 1500 for centered, 2100 for full)
+	 * @param len Number of channels, could up to 8
+	 */
+	int			set_failsafe_values(const uint16_t *vals, unsigned len);
 
 	/**
 	* Print the current status of IO
@@ -326,11 +334,11 @@ PX4IO::PX4IO() :
 	_to_actuators_effective(0),
 	_to_outputs(0),
 	_to_battery(0),
+	_primary_pwm_device(false),
 	_battery_amp_per_volt(90.0f/5.0f), // this matches the 3DR current sensor
 	_battery_amp_bias(0),
 	_battery_mamphour_total(0),
-	_battery_last_timestamp(0),
-	_primary_pwm_device(false)
+	_battery_last_timestamp(0)
 {
 	/* we need this potentially before it could be set in task_main */
 	g_dev = this;
@@ -690,6 +698,21 @@ PX4IO::io_set_control_state()
 }
 
 int
+PX4IO::set_failsafe_values(const uint16_t *vals, unsigned len)
+{
+	uint16_t 		regs[_max_actuators];
+
+	unsigned max = (len < _max_actuators) ? len : _max_actuators;
+
+	/* set failsafe values */
+	for (unsigned i = 0; i < max; i++)
+		regs[i] = FLOAT_TO_REG(vals[i]);
+
+	/* copy values to registers in IO */
+	return io_reg_set(PX4IO_PAGE_FAILSAFE_PWM, 0, regs, max);
+}
+
+int
 PX4IO::io_set_arming_state()
 {
 	actuator_armed_s	armed;		///< system armed state
@@ -1250,7 +1273,7 @@ PX4IO::print_status()
 	printf("%u bytes free\n",
 		io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FREEMEM));
 	uint16_t flags = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FLAGS);
-	printf("status 0x%04x%s%s%s%s%s%s%s%s%s%s%s\n",
+	printf("status 0x%04x%s%s%s%s%s%s%s%s%s%s%s%s\n",
 		flags,
 		((flags & PX4IO_P_STATUS_FLAGS_ARMED)    ? " ARMED" : ""),
 		((flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) ? " OVERRIDE" : ""),
@@ -1262,7 +1285,8 @@ PX4IO::print_status()
 		((flags & PX4IO_P_STATUS_FLAGS_RAW_PWM)  ? " RAW_PPM" : ""),
 		((flags & PX4IO_P_STATUS_FLAGS_MIXER_OK) ? " MIXER_OK" : " MIXER_FAIL"),
 		((flags & PX4IO_P_STATUS_FLAGS_ARM_SYNC) ? " ARM_SYNC" : " ARM_NO_SYNC"),
-		((flags & PX4IO_P_STATUS_FLAGS_INIT_OK)  ? " INIT_OK" : " INIT_FAIL"));
+		((flags & PX4IO_P_STATUS_FLAGS_INIT_OK)  ? " INIT_OK" : " INIT_FAIL"),
+		((flags & PX4IO_P_STATUS_FLAGS_FAILSAFE)  ? " FAILSAFE" : ""));
 	uint16_t alarms = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_ALARMS);
 	printf("alarms 0x%04x%s%s%s%s%s%s%s\n",
 		alarms,
@@ -1718,6 +1742,20 @@ px4io_main(int argc, char *argv[])
 		exit(0);
 	}
 
+	if (!strcmp(argv[1], "failsafe")) {
+
+		/* XXX parse arguments here */
+
+		if (g_dev != nullptr) {
+			/* XXX testing values */
+			uint16_t failsafe[4] = {1500, 1500, 1200, 1200};
+			g_dev->set_failsafe_values(failsafe, sizeof(failsafe) / sizeof(failsafe[0]));
+		} else {
+			errx(1, "not loaded");
+		}
+		exit(0);
+	}
+
 	if (!strcmp(argv[1], "recovery")) {
 
 		if (g_dev != nullptr) {
@@ -1845,5 +1883,5 @@ px4io_main(int argc, char *argv[])
 		monitor();
 
 	out:
-	errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug', 'recovery', 'limit', 'current' or 'update'");
+	errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug', 'recovery', 'limit', 'current', 'failsafe' or 'update'");
 }
diff --git a/src/modules/px4iofirmware/mixer.cpp b/src/modules/px4iofirmware/mixer.cpp
index 1234e2eea..448d2355f 100644
--- a/src/modules/px4iofirmware/mixer.cpp
+++ b/src/modules/px4iofirmware/mixer.cpp
@@ -102,13 +102,16 @@ mixer_tick(void)
 		r_status_flags |= PX4IO_P_STATUS_FLAGS_FMU_OK;
 	}
 
+	/* default to failsafe mixing */
 	source = MIX_FAILSAFE;
 
 	/*
 	 * Decide which set of controls we're using.
 	 */
-	if ((r_status_flags & PX4IO_P_STATUS_FLAGS_RAW_PWM) ||
-		!(r_status_flags & PX4IO_P_STATUS_FLAGS_MIXER_OK)) {
+
+	/* do not mix if mixer is invalid or if RAW_PWM mode is on and FMU is good */
+	if ((r_status_flags & PX4IO_P_STATUS_FLAGS_RAW_PWM) &&
+	        !(r_status_flags & PX4IO_P_STATUS_FLAGS_MIXER_OK)) {
 
 		/* don't actually mix anything - we already have raw PWM values or
 		 not a valid mixer. */
@@ -117,6 +120,7 @@ mixer_tick(void)
 	} else {
 
 		if (!(r_status_flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) &&
+		     (r_status_flags & PX4IO_P_STATUS_FLAGS_FMU_OK) &&
 		     (r_status_flags & PX4IO_P_STATUS_FLAGS_MIXER_OK)) {
 
 			/* mix from FMU controls */
@@ -133,14 +137,28 @@ mixer_tick(void)
 	}
 
 	/*
+	 * Set failsafe status flag depending on mixing source
+	 */
+	if (source == MIX_FAILSAFE) {
+		r_status_flags |= PX4IO_P_STATUS_FLAGS_FAILSAFE;
+	} else {
+		r_status_flags &= ~(PX4IO_P_STATUS_FLAGS_FAILSAFE);
+	}
+
+	/*
 	 * Run the mixers.
 	 */
 	if (source == MIX_FAILSAFE) {
 
 		/* copy failsafe values to the servo outputs */
-		for (unsigned i = 0; i < IO_SERVO_COUNT; i++)
+		for (unsigned i = 0; i < IO_SERVO_COUNT; i++) {
 			r_page_servos[i] = r_page_servo_failsafe[i];
 
+			/* safe actuators for FMU feedback */
+			r_page_actuators[i] = (r_page_servos[i] - 1500) / 600.0f;
+		}
+
+
 	} else if (source != MIX_NONE) {
 
 		float	outputs[IO_SERVO_COUNT];
@@ -156,7 +174,7 @@ mixer_tick(void)
 			r_page_actuators[i] = FLOAT_TO_REG(outputs[i]);
 
 			/* scale to servo output */
-			r_page_servos[i] = (outputs[i] * 500.0f) + 1500;
+			r_page_servos[i] = (outputs[i] * 600.0f) + 1500;
 
 		}
 		for (unsigned i = mixed; i < IO_SERVO_COUNT; i++)
@@ -175,7 +193,7 @@ mixer_tick(void)
 	bool should_arm = (
 	    /* FMU is armed */ (r_setup_arming & PX4IO_P_SETUP_ARMING_FMU_ARMED) &&
 	 	/* IO is armed */  (r_status_flags & PX4IO_P_STATUS_FLAGS_ARMED) &&
-		/* there is valid input */ (r_status_flags & (PX4IO_P_STATUS_FLAGS_RAW_PWM | PX4IO_P_STATUS_FLAGS_MIXER_OK)) &&
+		/* there is valid input via direct PWM or mixer */ (r_status_flags & (PX4IO_P_STATUS_FLAGS_RAW_PWM | PX4IO_P_STATUS_FLAGS_MIXER_OK)) &&
 		/* IO initialised without error */  (r_status_flags & PX4IO_P_STATUS_FLAGS_INIT_OK) &&
 		/* FMU is available or FMU is not available but override is an option */
 		((r_status_flags & PX4IO_P_STATUS_FLAGS_FMU_OK) || (!(r_status_flags & PX4IO_P_STATUS_FLAGS_FMU_OK) && (r_setup_arming & PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK) ))
@@ -225,7 +243,6 @@ mixer_callback(uintptr_t handle,
 
 	case MIX_FAILSAFE:
 	case MIX_NONE:
-		/* XXX we could allow for configuration of per-output failsafe values */
 		return -1;
 	}
 
diff --git a/src/modules/px4iofirmware/protocol.h b/src/modules/px4iofirmware/protocol.h
index e575bd841..674f9dddd 100644
--- a/src/modules/px4iofirmware/protocol.h
+++ b/src/modules/px4iofirmware/protocol.h
@@ -85,7 +85,7 @@
 #define PX4IO_P_CONFIG_ACTUATOR_COUNT		5	/* hardcoded max actuator output count */
 #define PX4IO_P_CONFIG_RC_INPUT_COUNT		6	/* hardcoded max R/C input count supported */
 #define PX4IO_P_CONFIG_ADC_INPUT_COUNT		7	/* hardcoded max ADC inputs */
-#define PX4IO_P_CONFIG_RELAY_COUNT		8	/* harcoded # of relay outputs */
+#define PX4IO_P_CONFIG_RELAY_COUNT		8	/* hardcoded # of relay outputs */
 
 /* dynamic status page */
 #define PX4IO_PAGE_STATUS		1
@@ -104,6 +104,7 @@
 #define PX4IO_P_STATUS_FLAGS_MIXER_OK		(1 << 8) /* mixer is OK */
 #define PX4IO_P_STATUS_FLAGS_ARM_SYNC		(1 << 9) /* the arming state between IO and FMU is in sync */
 #define PX4IO_P_STATUS_FLAGS_INIT_OK		(1 << 10) /* initialisation of the IO completed without error */
+#define PX4IO_P_STATUS_FLAGS_FAILSAFE		(1 << 11) /* failsafe is active */
 
 #define PX4IO_P_STATUS_ALARMS			3	 /* alarm flags - alarms latch, write 1 to a bit to clear it */
 #define PX4IO_P_STATUS_ALARMS_VBATT_LOW		(1 << 0) /* VBatt is very close to regulator dropout */
@@ -148,6 +149,7 @@
 #define PX4IO_P_SETUP_ARMING_IO_ARM_OK		(1 << 0) /* OK to arm the IO side */
 #define PX4IO_P_SETUP_ARMING_FMU_ARMED		(1 << 1) /* FMU is already armed */
 #define PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK	(1 << 2) /* OK to switch to manual override via override RC channel */
+#define PX4IO_P_SETUP_ARMING_FAILSAFE_CUSTOM	(1 << 3) /* use custom failsafe values, not 0 values of mixer */
 #define PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK	(1 << 4) /* OK to try in-air restart */
 
 #define PX4IO_P_SETUP_PWM_RATES			2	/* bitmask, 0 = low rate, 1 = high rate */
diff --git a/src/modules/px4iofirmware/registers.c b/src/modules/px4iofirmware/registers.c
index 9698a0f2f..3abf56a18 100644
--- a/src/modules/px4iofirmware/registers.c
+++ b/src/modules/px4iofirmware/registers.c
@@ -41,6 +41,7 @@
 
 #include <stdbool.h>
 #include <stdlib.h>
+#include <string.h>
 
 #include <drivers/drv_hrt.h>
 
@@ -179,7 +180,7 @@ uint16_t		r_page_rc_input_config[MAX_CONTROL_CHANNELS * PX4IO_P_RC_CONFIG_STRIDE
  *
  * Failsafe servo PWM values
  */
-uint16_t		r_page_servo_failsafe[IO_SERVO_COUNT];
+uint16_t		r_page_servo_failsafe[IO_SERVO_COUNT] = { 900, 900, 900, 900, 900, 900, 900, 900 };
 
 void
 registers_set(uint8_t page, uint8_t offset, const uint16_t *values, unsigned num_values)