diff options
Diffstat (limited to 'ROMFS/px4fmu_common/init.d/rcS')
| -rw-r--r-- | ROMFS/px4fmu_common/init.d/rcS | 701 |
1 files changed, 377 insertions, 324 deletions
diff --git a/ROMFS/px4fmu_common/init.d/rcS b/ROMFS/px4fmu_common/init.d/rcS index ed034877f..a9c5c59ea 100644 --- a/ROMFS/px4fmu_common/init.d/rcS +++ b/ROMFS/px4fmu_common/init.d/rcS @@ -8,39 +8,39 @@ # set MODE autostart -set logfile /fs/microsd/bootlog.txt +set LOG_FILE /fs/microsd/bootlog.txt +set RC_FILE /fs/microsd/etc/rc.txt +set CONFIG_FILE /fs/microsd/etc/config.txt +set EXTRAS_FILE /fs/microsd/etc/extras.txt + +set TUNE_OUT_ERROR ML<<CP4CP4CP4CP4CP4 # # Try to mount the microSD card. # -echo "[init] looking for microSD..." +echo "[init] Looking for microSD..." if mount -t vfat /dev/mmcsd0 /fs/microsd then - echo "[init] card mounted at /fs/microsd" + echo "[init] microSD card mounted at /fs/microsd" # Start playing the startup tune tone_alarm start else - echo "[init] no microSD card found" + echo "[init] No microSD card found" # Play SOS tone_alarm error fi # # Look for an init script on the microSD card. +# Disable autostart if the script found. # -# To prevent automatic startup in the current flight mode, -# the script should set MODE to some other value. -# -if [ -f /fs/microsd/etc/rc ] -then - echo "[init] reading /fs/microsd/etc/rc" - sh /fs/microsd/etc/rc -fi -# Also consider rc.txt files -if [ -f /fs/microsd/etc/rc.txt ] +if [ -f $RC_FILE ] then - echo "[init] reading /fs/microsd/etc/rc.txt" - sh /fs/microsd/etc/rc.txt + echo "[init] Executing init script: $RC_FILE" + sh $RC_FILE + set MODE custom +else + echo "[init] Init script not found: $RC_FILE" fi # if this is an APM build then there will be a rc.APM script @@ -52,20 +52,19 @@ then echo "[init] USB interface connected" fi - echo "Running rc.APM" + echo "[init] Running rc.APM" # if APM startup is successful then nsh will exit sh /etc/init.d/rc.APM fi if [ $MODE == autostart ] then + echo "[init] AUTOSTART mode" + # - # Start terminal + # Start CDC/ACM serial driver # - if sercon - then - echo "USB connected" - fi + sercon # # Start the ORB (first app to start) @@ -73,27 +72,20 @@ then uorb start # - # Load microSD params + # Load parameters # + set PARAM_FILE /fs/microsd/params if mtd start then - param select /fs/mtd_params - if param load /fs/mtd_params - then - else - echo "FAILED LOADING PARAMS" - fi + set PARAM_FILE /fs/mtd_params + fi + + param select $PARAM_FILE + if param load + then + echo "[init] Parameters loaded: $PARAM_FILE" else - param select /fs/microsd/params - if [ -f /fs/microsd/params ] - then - if param load /fs/microsd/params - then - echo "Parameters loaded" - else - echo "Parameter file corrupt - ignoring" - fi - fi + echo "[init] ERROR: Parameters loading failed: $PARAM_FILE" fi # @@ -101,355 +93,416 @@ then # if rgbled start then - echo "Using external RGB Led" + echo "[init] Using external RGB Led" else if blinkm start then + echo "[init] Using blinkm" blinkm systemstate fi fi # - # Start the Commander (needs to be this early for in-air-restarts) + # Set default values # - commander start - - if param compare SYS_AUTOSTART 1000 - then - sh /etc/init.d/1000_rc_fw_easystar.hil - set MODE custom - fi + set HIL no + set VEHICLE_TYPE none + set MIXER none + set USE_IO yes + set OUTPUT_MODE none + set PWM_OUTPUTS none + set PWM_RATE none + set PWM_DISARMED none + set PWM_MIN none + set PWM_MAX none + set MKBLCTRL_MODE none + set FMU_MODE pwm + set MAV_TYPE none - if param compare SYS_AUTOSTART 1001 + # + # Set DO_AUTOCONFIG flag to use it in AUTOSTART scripts + # + if param compare SYS_AUTOCONFIG 1 then - sh /etc/init.d/1001_rc_quad.hil - set MODE custom + set DO_AUTOCONFIG yes + else + set DO_AUTOCONFIG no fi - - if param compare SYS_AUTOSTART 1002 + + # + # Set parameters and env variables for selected AUTOSTART + # + if param compare SYS_AUTOSTART 0 then - sh /etc/init.d/1002_rc_fw_state.hil - set MODE custom + echo "[init] Don't try to find autostart script" + else + sh /etc/init.d/rc.autostart fi - - if param compare SYS_AUTOSTART 1003 + + # + # Override parameters from user configuration file + # + if [ -f $CONFIG_FILE ] then - sh /etc/init.d/1003_rc_quad_+.hil - set MODE custom + echo "[init] Reading config: $CONFIG_FILE" + sh $CONFIG_FILE + else + echo "[init] Config file not found: $CONFIG_FILE" fi - if param compare SYS_AUTOSTART 1004 + # + # If autoconfig parameter was set, reset it and save parameters + # + if [ $DO_AUTOCONFIG == yes ] then - sh /etc/init.d/1004_rc_fw_Rascal110.hil - set MODE custom + param set SYS_AUTOCONFIG 0 + param save fi - if [ $MODE != custom ] + set IO_PRESENT no + + if [ $USE_IO == yes ] then - # Try to get an USB console - nshterm /dev/ttyACM0 & + # + # Check if PX4IO present and update firmware if needed + # + if [ -f /etc/extras/px4io-v2_default.bin ] + then + set IO_FILE /etc/extras/px4io-v2_default.bin + else + set IO_FILE /etc/extras/px4io-v1_default.bin + fi + + if px4io checkcrc $IO_FILE + then + echo "[init] PX4IO CRC OK" + echo "PX4IO CRC OK" >> $LOG_FILE + + set IO_PRESENT yes + else + echo "[init] PX4IO CRC failure, trying to update" + echo "PX4IO CRC failure" >> $LOG_FILE + + tone_alarm MLL32CP8MB + + if px4io forceupdate 14662 $IO_FILE + then + usleep 500000 + if px4io checkcrc $IO_FILE + then + echo "[init] PX4IO CRC OK, update successful" + echo "PX4IO CRC OK after updating" >> $LOG_FILE + tone_alarm MLL8CDE + + set IO_PRESENT yes + else + echo "[init] ERROR: PX4IO update failed" + echo "PX4IO update failed" >> $LOG_FILE + fi + else + echo "[init] ERROR: PX4IO update failed" + echo "PX4IO update failed" >> $LOG_FILE + fi + fi + + if [ $IO_PRESENT == no ] + then + echo "[init] ERROR: PX4IO not found" + tone_alarm $TUNE_OUT_ERROR + fi fi - + # - # Upgrade PX4IO firmware + # Set default output if not set # + if [ $OUTPUT_MODE == none ] + then + if [ $USE_IO == yes ] + then + set OUTPUT_MODE io + else + set OUTPUT_MODE fmu + fi + fi - if [ -f /etc/extras/px4io-v2_default.bin ] + if [ $OUTPUT_MODE == io -a $IO_PRESENT != yes ] then - set io_file /etc/extras/px4io-v2_default.bin - else - set io_file /etc/extras/px4io-v1_default.bin + # Need IO for output but it not present, disable output + set OUTPUT_MODE none + echo "[init] ERROR: PX4IO not found, disabling output" + + # Avoid using ttyS0 for MAVLink on FMUv1 + if hw_ver compare PX4FMU_V1 + then + set FMU_MODE serial + fi fi - if px4io start + if [ $HIL == yes ] then - echo "PX4IO OK" - echo "PX4IO OK" >> $logfile + set OUTPUT_MODE hil + if hw_ver compare PX4FMU_V1 + then + set FMU_MODE serial + fi + else + # Try to get an USB console if not in HIL mode + nshterm /dev/ttyACM0 & fi - if px4io checkcrc $io_file + # + # Start the Commander (needs to be this early for in-air-restarts) + # + commander start + + # + # Start primary output + # + set TTYS1_BUSY no + + # If OUTPUT_MODE == none then something is wrong with setup and we shouldn't try to enable output + if [ $OUTPUT_MODE != none ] then - echo "PX4IO CRC OK" - echo "PX4IO CRC OK" >> $logfile - else - echo "PX4IO CRC failure" - echo "PX4IO CRC failure" >> $logfile - tone_alarm MBABGP - if px4io forceupdate 14662 $io_file + if [ $OUTPUT_MODE == io ] then - usleep 500000 + echo "[init] Use PX4IO PWM as primary output" if px4io start then - echo "PX4IO restart OK" - echo "PX4IO restart OK" >> $logfile - tone_alarm MSPAA + echo "[init] PX4IO started" + sh /etc/init.d/rc.io else - echo "PX4IO restart failed" - echo "PX4IO restart failed" >> $logfile - tone_alarm MNGGG - sleep 10 - reboot + echo "[init] ERROR: PX4IO start failed" + tone_alarm $TUNE_OUT_ERROR + fi + fi + if [ $OUTPUT_MODE == fmu ] + then + echo "[init] Use FMU PWM as primary output" + if fmu mode_$FMU_MODE + then + echo "[init] FMU mode_$FMU_MODE started" + else + echo "[init] ERROR: FMU mode_$FMU_MODE start failed" + tone_alarm $TUNE_OUT_ERROR + fi + + if hw_ver compare PX4FMU_V1 + then + if [ $FMU_MODE == pwm -o $FMU_MODE == gpio ] + then + set TTYS1_BUSY yes + fi + if [ $FMU_MODE == pwm_gpio ] + then + set TTYS1_BUSY yes + fi + fi + fi + if [ $OUTPUT_MODE == mkblctrl ] + then + echo "[init] Use MKBLCTRL as primary output" + set MKBLCTRL_ARG "" + if [ $MKBLCTRL_MODE == x ] + then + set MKBLCTRL_ARG "-mkmode x" + fi + if [ $MKBLCTRL_MODE == + ] + then + set MKBLCTRL_ARG "-mkmode +" + fi + + if mkblctrl $MKBLCTRL_ARG + then + echo "[init] MKBLCTRL started" + else + echo "[init] ERROR: MKBLCTRL start failed" + tone_alarm $TUNE_OUT_ERROR + fi + + fi + if [ $OUTPUT_MODE == hil ] + then + echo "[init] Use HIL as primary output" + if hil mode_pwm + then + echo "[init] HIL output started" + else + echo "[init] ERROR: HIL output start failed" + tone_alarm $TUNE_OUT_ERROR + fi + fi + + # + # Start IO or FMU for RC PPM input if needed + # + if [ $IO_PRESENT == yes ] + then + if [ $OUTPUT_MODE != io ] + then + if px4io start + then + echo "[init] PX4IO started" + sh /etc/init.d/rc.io + else + echo "[init] ERROR: PX4IO start failed" + tone_alarm $TUNE_OUT_ERROR + fi fi else - echo "PX4IO update failed" - echo "PX4IO update failed" >> $logfile - tone_alarm MNGGG + if [ $OUTPUT_MODE != fmu ] + then + if fmu mode_$FMU_MODE + then + echo "[init] FMU mode_$FMU_MODE started" + else + echo "[init] ERROR: FMU mode_$FMU_MODE start failed" + tone_alarm $TUNE_OUT_ERROR + fi + + if hw_ver compare PX4FMU_V1 + then + if [ $FMU_MODE == pwm -o $FMU_MODE == gpio ] + then + set TTYS1_BUSY yes + fi + if [ $FMU_MODE == pwm_gpio ] + then + set TTYS1_BUSY yes + fi + fi + fi fi fi - - set EXIT_ON_END no # - # Check if auto-setup from one of the standard scripts is wanted - # SYS_AUTOSTART = 0 means no autostart (default) - # - # AUTOSTART PARTITION: - # 0 .. 999 Reserved (historical) - # 1000 .. 1999 Simulation setups - # 2000 .. 2999 Standard planes - # 3000 .. 3999 Flying wing - # 4000 .. 4999 Quad X - # 5000 .. 5999 Quad + - # 6000 .. 6999 Hexa X - # 7000 .. 7999 Hexa + - # 8000 .. 8999 Octo X - # 9000 .. 9999 Octo + - # 10000 .. 10999 Wide arm / H frame - # 11000 .. 11999 Hexa Cox - # 12000 .. 12999 Octo Cox - - if param compare SYS_AUTOSTART 4008 8 - then - sh /etc/init.d/4008_ardrone - set MODE custom - fi + # MAVLink + # + set EXIT_ON_END no - if param compare SYS_AUTOSTART 4009 9 + if [ $HIL == yes ] then - sh /etc/init.d/4009_ardrone_flow - set MODE custom + sleep 1 + mavlink start -b 230400 -d /dev/ttyACM0 + usleep 5000 + else + if [ $TTYS1_BUSY == yes ] + then + # Start MAVLink on ttyS0, because FMU ttyS1 pins configured as something else + mavlink start -d /dev/ttyS0 + usleep 5000 + + # Exit from nsh to free port for mavlink + set EXIT_ON_END yes + else + # Start MAVLink on default port: ttyS1 + mavlink start + usleep 5000 + fi fi - if param compare SYS_AUTOSTART 4010 10 - then - set FRAME_GEOMETRY x - set FRAME_COUNT 4 - set PWM_MIN 1200 - set PWM_MAX 1900 - set PWM_DISARMED 900 - sh /etc/init.d/4010_dji_f330 - set MODE custom - fi - - if param compare SYS_AUTOSTART 4011 11 - then - sh /etc/init.d/4011_dji_f450 - set MODE custom - fi - - if param compare SYS_AUTOSTART 4012 - then - sh /etc/init.d/666_fmu_q_x550 - set MODE custom - fi - - if param compare SYS_AUTOSTART 6012 12 - then - set MIXER /etc/mixers/FMU_hex_x.mix - sh /etc/init.d/rc.hexa - set MODE custom - fi - - if param compare SYS_AUTOSTART 7013 13 - then - set MIXER /etc/mixers/FMU_hex_+.mix - sh /etc/init.d/rc.hexa - set MODE custom - fi - - if param compare SYS_AUTOSTART 8001 - then - set MIXER /etc/mixers/FMU_octo_x.mix - sh /etc/init.d/rc.octo - set MODE custom - fi - - if param compare SYS_AUTOSTART 9001 - then - set MIXER /etc/mixers/FMU_octo_+.mix - sh /etc/init.d/rc.octo - set MODE custom - fi + # + # Sensors, Logging, GPS + # + echo "[init] Start sensors" + sh /etc/init.d/rc.sensors - if param compare SYS_AUTOSTART 12001 + if [ $HIL == no ] then - set MIXER /etc/mixers/FMU_octo_cox.mix - sh /etc/init.d/rc.octo - set MODE custom + echo "[init] Start logging" + sh /etc/init.d/rc.logging + + echo "[init] Start GPS" + gps start fi - if param compare SYS_AUTOSTART 10015 15 - then - sh /etc/init.d/10015_tbs_discovery - set MODE custom - fi - - if param compare SYS_AUTOSTART 10016 16 - then - sh /etc/init.d/10016_3dr_iris - set MODE custom - fi - - # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame - if param compare SYS_AUTOSTART 4017 17 - then - set MKBLCTRL_MODE no - set MKBLCTRL_FRAME x - sh /etc/init.d/rc.custom_dji_f330_mkblctrl - set MODE custom - fi - - # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame - if param compare SYS_AUTOSTART 5018 18 - then - set MKBLCTRL_MODE no - set MKBLCTRL_FRAME + - sh /etc/init.d/rc.custom_dji_f330_mkblctrl - set MODE custom - fi - - # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame Mikrokopter-Addressing - if param compare SYS_AUTOSTART 4019 19 - then - set MKBLCTRL_MODE yes - set MKBLCTRL_FRAME x - sh /etc/init.d/rc.custom_dji_f330_mkblctrl - set MODE custom - fi - - # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame Mikrokopter-Addressing - if param compare SYS_AUTOSTART 5020 20 + # + # Fixed wing setup + # + if [ $VEHICLE_TYPE == fw ] then - set MKBLCTRL_MODE yes - set MKBLCTRL_FRAME + - sh /etc/init.d/rc.custom_dji_f330_mkblctrl - set MODE custom + echo "[init] Vehicle type: FIXED WING" + + if [ $MIXER == none ] + then + # Set default mixer for fixed wing if not defined + set MIXER FMU_AERT + fi + + if [ $MAV_TYPE == none ] + then + # Use MAV_TYPE = 1 (fixed wing) if not defined + set MAV_TYPE 1 + fi + + param set MAV_TYPE $MAV_TYPE + + # Load mixer and configure outputs + sh /etc/init.d/rc.interface + + # Start standard fixedwing apps + sh /etc/init.d/rc.fw_apps fi - # PX4FMU v1 with IO + PPM-based ESCs on Quad X-shape frame - if param compare SYS_AUTOSTART 4021 21 + # + # Multicopters setup + # + if [ $VEHICLE_TYPE == mc ] then - set FRAME_GEOMETRY x - set ESC_MAKER afro - sh /etc/init.d/rc.custom_io_esc - set MODE custom - fi + echo "[init] Vehicle type: MULTICOPTER" - # PX4FMU v1 with IO + PPM-based ESCs on Quad X-shape frame - if param compare SYS_AUTOSTART 10022 22 - then - set FRAME_GEOMETRY w - sh /etc/init.d/rc.custom_io_esc - set MODE custom - fi - - if param compare SYS_AUTOSTART 3030 30 - then - sh /etc/init.d/3030_io_camflyer - set MODE custom - fi + if [ $MIXER == none ] + then + # Set default mixer for multicopter if not defined + set MIXER quad_x + fi - if param compare SYS_AUTOSTART 3031 31 - then - sh /etc/init.d/3031_io_phantom - set MODE custom - fi - - if param compare SYS_AUTOSTART 3032 32 - then - sh /etc/init.d/3032_skywalker_x5 - set MODE custom - fi + if [ $MAV_TYPE == none ] + then + # Use MAV_TYPE = 2 (quadcopter) if not defined + set MAV_TYPE 2 + + # Use mixer to detect vehicle type + if [ $MIXER == FMU_hex_x -o $MIXER == FMU_hex_+ ] + then + param set MAV_TYPE 13 + fi + if [ $MIXER == FMU_octo_x -o $MIXER == FMU_octo_+ ] + then + param set MAV_TYPE 14 + fi + if [ $MIXER == FMU_octo_cox ] + then + param set MAV_TYPE 14 + fi + fi - if param compare SYS_AUTOSTART 3033 33 - then - sh /etc/init.d/3033_io_wingwing - set MODE custom + param set MAV_TYPE $MAV_TYPE + + # Load mixer and configure outputs + sh /etc/init.d/rc.interface + + # Start standard multicopter apps + sh /etc/init.d/rc.mc_apps fi - if param compare SYS_AUTOSTART 3034 34 - then - sh /etc/init.d/3034_io_fx79 - set MODE custom - fi - - if param compare SYS_AUTOSTART 40 - then - sh /etc/init.d/40_io_segway - set MODE custom - fi - - if param compare SYS_AUTOSTART 2100 100 + # + # Generic setup (autostart ID not found) + # + if [ $VEHICLE_TYPE == none ] then - sh /etc/init.d/2100_mpx_easystar - set MODE custom - fi + echo "[init] Vehicle type: GENERIC" - if param compare SYS_AUTOSTART 2101 101 - then - sh /etc/init.d/2101_hk_bixler - set MODE custom + # Load mixer and configure outputs + sh /etc/init.d/rc.interface fi - if param compare SYS_AUTOSTART 2102 102 - then - sh /etc/init.d/2102_3dr_skywalker - set MODE custom - fi - - if param compare SYS_AUTOSTART 800 - then - sh /etc/init.d/800_sdlogger - set MODE custom - fi - - # Start any custom extensions that might be missing - if [ -f /fs/microsd/etc/rc.local ] - then - sh /fs/microsd/etc/rc.local - fi - - # If none of the autostart scripts triggered, get a minimal setup - if [ $MODE == autostart ] + # Start any custom addons + if [ -f $EXTRAS_FILE ] then - # Telemetry port is on both FMU boards ttyS1 - # but the AR.Drone motors can be get 'flashed' - # if starting MAVLink on them - so do not - # start it as default (default link: USB) - - # Start commander - commander start - - # Start px4io if present - if px4io detect - then - px4io start - else - if fmu mode_serial - then - echo "FMU driver (no PWM) started" - fi - fi - - # Start sensors - sh /etc/init.d/rc.sensors - - # Start one of the estimators - attitude_estimator_ekf start - - # Start GPS - gps start - + echo "[init] Starting addons script: $EXTRAS_FILE" + sh $EXTRAS_FILE + else + echo "[init] Addons script not found: $EXTRAS_FILE" fi if [ $EXIT_ON_END == yes ] |