diff options
Diffstat (limited to 'ROMFS/px4fmu_common')
47 files changed, 2298 insertions, 914 deletions
diff --git a/ROMFS/px4fmu_common/init.d/01_fmu_quad_x b/ROMFS/px4fmu_common/init.d/01_fmu_quad_x deleted file mode 100644 index 58a970eba..000000000 --- a/ROMFS/px4fmu_common/init.d/01_fmu_quad_x +++ /dev/null @@ -1,107 +0,0 @@ -#!nsh -# -# Flight startup script for PX4FMU with PWM outputs. -# - -# disable USB and autostart -set USB no -set MODE custom - -echo "[init] doing PX4FMU Quad startup..." - -# -# Start the ORB -# -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi - -# -# Load default params for this platform -# -if param compare SYS_AUTOCONFIG 1 -then - # Set all params here, then disable autoconfig - param set MC_ATTRATE_P 0.14 - param set MC_ATTRATE_I 0 - param set MC_ATTRATE_D 0.006 - param set MC_ATT_P 5.5 - param set MC_ATT_I 0 - param set MC_ATT_D 0 - param set MC_YAWPOS_D 0 - param set MC_YAWPOS_I 0 - param set MC_YAWPOS_P 0.6 - param set MC_YAWRATE_D 0 - param set MC_YAWRATE_I 0 - param set MC_YAWRATE_P 0.08 - param set RC_SCALE_PITCH 1 - param set RC_SCALE_ROLL 1 - param set RC_SCALE_YAW 3 - - param set SYS_AUTOCONFIG 0 - param save /fs/microsd/params -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ -# -param set MAV_TYPE 2 - -# -# Start MAVLink -# -mavlink start -d /dev/ttyS0 -b 57600 -usleep 5000 - -# -# Start the sensors and test them. -# -sh /etc/init.d/rc.sensors - -# -# Start the commander. -# -commander start - -# -# Start GPS interface (depends on orb) -# -gps start - -# -# Start the attitude estimator -# -attitude_estimator_ekf start - -echo "[init] starting PWM output" -fmu mode_pwm -mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix -pwm -u 400 -m 0xff - -# -# Start attitude control -# -multirotor_att_control start - -# -# Start logging -# -sdlog2 start -r 50 -a -b 14 - -# -# Start system state -# -if blinkm start -then - blinkm systemstate -fi diff --git a/ROMFS/px4fmu_common/init.d/02_io_quad_x b/ROMFS/px4fmu_common/init.d/02_io_quad_x deleted file mode 100644 index c63e92f6d..000000000 --- a/ROMFS/px4fmu_common/init.d/02_io_quad_x +++ /dev/null @@ -1,101 +0,0 @@ -#!nsh -# -# Flight startup script for PX4FMU+PX4IO -# - -# disable USB and autostart -set USB no -set MODE custom - -# -# Start the ORB (first app to start) -# -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi - -# -# Load default params for this platform -# -if param compare SYS_AUTOCONFIG 1 -then - # Set all params here, then disable autoconfig - param set SYS_AUTOCONFIG 0 - param save /fs/microsd/params -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ -# -param set MAV_TYPE 2 - -# -# Start MAVLink (depends on orb) -# -mavlink start -d /dev/ttyS1 -b 57600 -usleep 5000 - -# -# Start the commander (depends on orb, mavlink) -# -commander start - -# -# Start PX4IO interface (depends on orb, commander) -# -px4io start - -# -# Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. -px4io recovery - -# -# Disable px4io topic limiting -# -px4io limit 200 - -# -# Start the sensors (depends on orb, px4io) -# -sh /etc/init.d/rc.sensors - -# -# Start GPS interface (depends on orb) -# -gps start - -# -# Start the attitude estimator (depends on orb) -# -attitude_estimator_ekf start - -# -# Load mixer and start controllers (depends on px4io) -# -mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix -pwm -u 400 -m 0xff -multirotor_att_control start - -# -# Start logging -# -sdlog2 start -r 50 -a -b 14 - -# -# Start system state -# -if blinkm start -then - blinkm systemstate -fi diff --git a/ROMFS/px4fmu_common/init.d/08_ardrone b/ROMFS/px4fmu_common/init.d/08_ardrone index f55ac2ae3..f6f09ac22 100644 --- a/ROMFS/px4fmu_common/init.d/08_ardrone +++ b/ROMFS/px4fmu_common/init.d/08_ardrone @@ -1,99 +1,57 @@ #!nsh -# -# Flight startup script for PX4FMU on PX4IOAR carrier board. -# - -# Disable the USB interface -set USB no -# Disable autostarting other apps -set MODE ardrone - -echo "[init] doing PX4IOAR startup..." - -# -# Start the ORB -# -uorb start +echo "[init] 08_ardrone: PX4FMU on PX4IOAR carrier board" # -# Load microSD params +# Load default params for this platform # -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] +if param compare SYS_AUTOCONFIG 1 then - param load /fs/microsd/params + # Set all params here, then disable autoconfig + param set MC_ATTRATE_D 0 + param set MC_ATTRATE_I 0 + param set MC_ATTRATE_P 0.13 + param set MC_ATT_D 0 + param set MC_ATT_I 0.3 + param set MC_ATT_P 5 + param set MC_YAWPOS_D 0.1 + param set MC_YAWPOS_I 0.15 + param set MC_YAWPOS_P 1 + param set MC_YAWRATE_D 0 + param set MC_YAWRATE_I 0 + param set MC_YAWRATE_P 0.15 + + param set SYS_AUTOCONFIG 0 + param save fi # # Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ +# MAV_TYPE 2 = quadrotor # param set MAV_TYPE 2 +param set BAT_V_SCALING 0.008381 # -# Configure PX4FMU for operation with PX4IOAR -# -fmu mode_gpio_serial - -# -# Start the sensors. -# -sh /etc/init.d/rc.sensors - -# # Start MAVLink # mavlink start -d /dev/ttyS0 -b 57600 usleep 5000 - -# -# Start the commander. -# -commander start - -# -# Start the attitude estimator -# -attitude_estimator_ekf start - + # -# Fire up the multi rotor attitude controller +# Configure PX4FMU for operation with PX4IOAR # -multirotor_att_control start +fmu mode_gpio_serial # # Fire up the AR.Drone interface. # ardrone_interface start -d /dev/ttyS1 - -# -# Start logging -# -sdlog start -s 10 - -# -# Start GPS capture -# -gps start - -# -# Start system state -# -if blinkm start -then - echo "using BlinkM for state indication" - blinkm systemstate -else - echo "no BlinkM found, OK." -fi # -# startup is done; we don't want the shell because we -# use the same UART for telemetry +# Start common for all multirotors apps # -echo "[init] startup done" - +sh /etc/init.d/rc.multirotor + +# Exit, because /dev/ttyS0 is needed for MAVLink exit diff --git a/ROMFS/px4fmu_common/init.d/09_ardrone_flow b/ROMFS/px4fmu_common/init.d/09_ardrone_flow index e7173f6e6..9b739f245 100644 --- a/ROMFS/px4fmu_common/init.d/09_ardrone_flow +++ b/ROMFS/px4fmu_common/init.d/09_ardrone_flow @@ -1,42 +1,53 @@ #!nsh -# -# Flight startup script for PX4FMU on PX4IOAR carrier board. -# -# Disable the USB interface -set USB no +echo "[init] 09_ardrone_flow: PX4FMU on PX4IOAR carrier board with PX4FLOW" -# Disable autostarting other apps -set MODE ardrone - -echo "[init] doing PX4IOAR startup..." - # -# Start the ORB +# Load default params for this platform # -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] +if param compare SYS_AUTOCONFIG 1 then - param load /fs/microsd/params + # Set all params here, then disable autoconfig + param set MC_ATTRATE_D 0 + param set MC_ATTRATE_I 0 + param set MC_ATTRATE_P 0.13 + param set MC_ATT_D 0 + param set MC_ATT_I 0.3 + param set MC_ATT_P 5 + param set MC_YAWPOS_D 0.1 + param set MC_YAWPOS_I 0.15 + param set MC_YAWPOS_P 1 + param set MC_YAWRATE_D 0 + param set MC_YAWRATE_I 0 + param set MC_YAWRATE_P 0.15 + + param set SYS_AUTOCONFIG 0 + param save fi # # Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ +# MAV_TYPE 2 = quadrotor # param set MAV_TYPE 2 +param set BAT_V_SCALING 0.008381 + +# +# Start MAVLink and MAVLink Onboard (PX4FLOW Sensor) +# +mavlink start -d /dev/ttyS0 -b 57600 +mavlink_onboard start -d /dev/ttyS3 -b 115200 +usleep 5000 # # Configure PX4FMU for operation with PX4IOAR # fmu mode_gpio_serial + +# +# Fire up the AR.Drone interface. +# +ardrone_interface start -d /dev/ttyS1 # # Start the sensors. @@ -44,13 +55,6 @@ fmu mode_gpio_serial sh /etc/init.d/rc.sensors # -# Start MAVLink and MAVLink Onboard (Flow Sensor) -# -mavlink start -d /dev/ttyS0 -b 57600 -mavlink_onboard start -d /dev/ttyS3 -b 115200 -usleep 5000 - -# # Start the commander. # commander start @@ -79,16 +83,6 @@ flow_position_control start # Fire up the flow speed controller # flow_speed_control start - -# -# Fire up the AR.Drone interface. -# -ardrone_interface start -d /dev/ttyS1 -# -# startup is done; we don't want the shell because we -# use the same UART for telemetry -# -echo "[init] startup done" - +# Exit, because /dev/ttyS0 is needed for MAVLink exit diff --git a/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil b/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil new file mode 100644 index 000000000..40a13b5d1 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil @@ -0,0 +1,87 @@ +#!nsh +# +# USB HIL start +# + +echo "[HIL] HILStar starting.." + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + param set FW_L1_PERIOD 16 + param set RC_SCALE_ROLL 1.0 + param set RC_SCALE_PITCH 1.0 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# Allow USB some time to come up +sleep 1 +# Tell MAVLink that this link is "fast" +mavlink start -b 230400 -d /dev/ttyACM0 + +# Create a fake HIL /dev/pwm_output interface +hil mode_pwm + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor +# see https://pixhawk.ethz.ch/mavlink/ +# +param set MAV_TYPE 1 + +# +# Check if we got an IO +# +if px4io start +then + echo "IO started" +else + fmu mode_serial + echo "FMU started" +fi + +# +# Start the sensors (depends on orb, px4io) +# +sh /etc/init.d/rc.sensors + +# +# Start the attitude estimator (depends on orb) +# +att_pos_estimator_ekf start + +# +# Load mixer and start controllers (depends on px4io) +# +mixer load /dev/pwm_output /etc/mixers/FMU_AET.mix +fw_pos_control_l1 start +fw_att_control start + +echo "[HIL] setup done, running" + diff --git a/ROMFS/px4fmu_common/init.d/1001_rc_quad.hil b/ROMFS/px4fmu_common/init.d/1001_rc_quad.hil new file mode 100644 index 000000000..9b664d63e --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1001_rc_quad.hil @@ -0,0 +1,105 @@ +#!nsh +# +# USB HIL start +# + +echo "[HIL] HILS quadrotor starting.." + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.0 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.05 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 3.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.1 + param set MC_YAWRATE_D 0.0 + param set MC_YAWRATE_I 0.0 + param set MC_YAWRATE_P 0.05 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.5 + param set MPC_THR_MIN 0.1 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +# Allow USB some time to come up +sleep 1 +# Tell MAVLink that this link is "fast" +mavlink start -b 230400 -d /dev/ttyACM0 + +# Create a fake HIL /dev/pwm_output interface +hil mode_pwm + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor +# see https://pixhawk.ethz.ch/mavlink/ +# +param set MAV_TYPE 2 + +# +# Check if we got an IO +# +if px4io start +then + echo "IO started" +else + fmu mode_serial + echo "FMU started" +fi + +# +# Start the sensors (depends on orb, px4io) +# +sh /etc/init.d/rc.sensors + +# +# Start the attitude estimator (depends on orb) +# +att_pos_estimator_ekf start + +# +# Load mixer and start controllers (depends on px4io) +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix + +# +# Start position estimator +# +position_estimator_inav start + +# +# Start attitude control +# +multirotor_att_control start + +# +# Start position control +# +multirotor_pos_control start + +echo "[HIL] setup done, running" + diff --git a/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil b/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil new file mode 100644 index 000000000..7b9f41bf6 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil @@ -0,0 +1,79 @@ +#!nsh +# +# USB HIL start +# + +echo "[HIL] HILStar starting in state-HIL mode.." + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# Allow USB some time to come up +sleep 1 +# Tell MAVLink that this link is "fast" +mavlink start -b 230400 -d /dev/ttyACM0 + +# Create a fake HIL /dev/pwm_output interface +hil mode_pwm + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor +# see https://pixhawk.ethz.ch/mavlink/ +# +param set MAV_TYPE 1 + +# +# Check if we got an IO +# +if px4io start +then + echo "IO started" +else + fmu mode_serial + echo "FMU started" +fi + +# +# Start the sensors (depends on orb, px4io) +# +sh /etc/init.d/rc.sensors + +# +# Load mixer and start controllers (depends on px4io) +# +mixer load /dev/pwm_output /etc/mixers/FMU_AET.mix +fw_pos_control_l1 start +fw_att_control start + +echo "[HIL] setup done, running" + diff --git a/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil b/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil new file mode 100644 index 000000000..0cc07ad34 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil @@ -0,0 +1,105 @@ +#!nsh +# +# USB HIL start +# + +echo "[HIL] HILS quadrotor + starting.." + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.0 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.05 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 3.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.1 + param set MC_YAWRATE_D 0.0 + param set MC_YAWRATE_I 0.0 + param set MC_YAWRATE_P 0.05 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.5 + param set MPC_THR_MIN 0.1 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +# Allow USB some time to come up +sleep 1 +# Tell MAVLink that this link is "fast" +mavlink start -b 230400 -d /dev/ttyACM0 + +# Create a fake HIL /dev/pwm_output interface +hil mode_pwm + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor +# see https://pixhawk.ethz.ch/mavlink/ +# +param set MAV_TYPE 2 + +# +# Check if we got an IO +# +if px4io start +then + echo "IO started" +else + fmu mode_serial + echo "FMU started" +fi + +# +# Start the sensors (depends on orb, px4io) +# +sh /etc/init.d/rc.sensors + +# +# Start the attitude estimator (depends on orb) +# +att_pos_estimator_ekf start + +# +# Load mixer and start controllers (depends on px4io) +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_+.mix + +# +# Start position estimator +# +position_estimator_inav start + +# +# Start attitude control +# +multirotor_att_control start + +# +# Start position control +# +multirotor_pos_control start + +echo "[HIL] setup done, running" + diff --git a/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil b/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil new file mode 100644 index 000000000..344d78422 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil @@ -0,0 +1,98 @@ +#!nsh +# +# USB HIL start +# + +echo "[HIL] HILStar starting.." + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + param set FW_L1_PERIOD 16 + param set RC_SCALE_ROLL 1.0 + param set RC_SCALE_PITCH 1.0 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# Allow USB some time to come up +sleep 1 +# Tell MAVLink that this link is "fast" +mavlink start -b 230400 -d /dev/ttyACM0 + +# Create a fake HIL /dev/pwm_output interface +hil mode_pwm + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor +# see https://pixhawk.ethz.ch/mavlink/ +# +param set MAV_TYPE 1 + +# +# Check if we got an IO +# +if px4io start +then + echo "IO started" +else + fmu mode_serial + echo "FMU started" +fi + +# +# Start the sensors (depends on orb, px4io) +# +sh /etc/init.d/rc.sensors + +# +# Start the attitude estimator (depends on orb) +# +att_pos_estimator_ekf start + +# +# Load mixer and start controllers (depends on px4io) +# +set MODE autostart +mixer load /dev/pwm_output /etc/mixers/FMU_AERT.mix +if [ -f /fs/microsd/etc/mixers/FMU_AERT.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_AERT.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_AERT.mix +else + echo "Using /etc/mixers/FMU_AERT.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_AERT.mix +fi + + +fw_pos_control_l1 start +fw_att_control start + +echo "[HIL] setup done, running" + diff --git a/ROMFS/px4fmu_common/init.d/100_mpx_easystar b/ROMFS/px4fmu_common/init.d/100_mpx_easystar new file mode 100644 index 000000000..abe378b22 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/100_mpx_easystar @@ -0,0 +1,87 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on EasyStar" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + param set FW_L1_PERIOD 16 + param set RC_SCALE_ROLL 1.0 + param set RC_SCALE_PITCH 1.0 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing +# +param set MAV_TYPE 1 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + + sh /etc/init.d/rc.io + # Limit to 100 Hz updates and (implicit) 50 Hz PWM + px4io limit 100 +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer and start controllers (depends on px4io) +# +if [ -f /fs/microsd/etc/mixers/FMU_RET.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_RET.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_RET.mix +else + echo "Using /etc/mixers/FMU_RET.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_RET.mix +fi + +# +# Start common fixedwing apps +# +sh /etc/init.d/rc.fixedwing + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/101_hk_bixler b/ROMFS/px4fmu_common/init.d/101_hk_bixler new file mode 100644 index 000000000..c616da988 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/101_hk_bixler @@ -0,0 +1,87 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on HK Bixler" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + param set FW_L1_PERIOD 16 + param set RC_SCALE_ROLL 1.0 + param set RC_SCALE_PITCH 1.0 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing +# +param set MAV_TYPE 1 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + + sh /etc/init.d/rc.io + # Limit to 100 Hz updates and (implicit) 50 Hz PWM + px4io limit 100 +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer and start controllers (depends on px4io) +# +if [ -f /fs/microsd/etc/mixers/FMU_AERT.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_AERT.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_AERT.mix +else + echo "Using /etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_AERT.mix +fi + +# +# Start common fixedwing apps +# +sh /etc/init.d/rc.fixedwing + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/10_dji_f330 b/ROMFS/px4fmu_common/init.d/10_dji_f330 new file mode 100644 index 000000000..467b56bbf --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/10_dji_f330 @@ -0,0 +1,97 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on DJI F330" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.004 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.12 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 7.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.0 + param set MC_YAWRATE_D 0.005 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_P 0.3 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.7 + param set MPC_THR_MIN 0.3 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix + +# +# Set PWM output frequency +# +pwm rate -c 1234 -r 400 + +# +# Set disarmed, min and max PWM signals (for DJI ESCs) +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1200 +pwm max -c 1234 -p 1800 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/10_io_f330 b/ROMFS/px4fmu_common/init.d/10_io_f330 deleted file mode 100644 index 4450eb50d..000000000 --- a/ROMFS/px4fmu_common/init.d/10_io_f330 +++ /dev/null @@ -1,116 +0,0 @@ -#!nsh -# -# Flight startup script for PX4FMU+PX4IO -# - -# disable USB and autostart -set USB no -set MODE custom - -# -# Load default params for this platform -# -if param compare SYS_AUTOCONFIG 1 -then - # Set all params here, then disable autoconfig - param set SYS_AUTOCONFIG 0 - - param set MC_ATTRATE_D 0.005 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_P 0.1 - param set MC_ATT_D 0.0 - param set MC_ATT_I 0.0 - param set MC_ATT_P 4.5 - param set MC_RCLOSS_THR 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWPOS_I 0.3 - param set MC_YAWPOS_P 0.6 - param set MC_YAWRATE_D 0.0 - param set MC_YAWRATE_I 0.0 - param set MC_YAWRATE_P 0.1 - - param save /fs/microsd/params -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ -# -param set MAV_TYPE 2 - -# -# Start MAVLink (depends on orb) -# -mavlink start -usleep 5000 - -# -# Start PX4IO interface (depends on orb, commander) -# -px4io start -pwm -u 400 -m 0xff - -# -# Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. -px4io recovery - -# -# Disable px4io topic limiting -# -px4io limit 200 - -# -# This sets a PWM right after startup (regardless of safety button) -# -px4io idle 900 900 900 900 - -# -# The values are for spinning motors when armed using DJI ESCs -# -px4io min 1200 1200 1200 1200 - -# -# Upper limits could be higher, this is on the safe side -# -px4io max 1800 1800 1800 1800 - -# -# Start the sensors (depends on orb, px4io) -# -sh /etc/init.d/rc.sensors - -# -# Start the commander (depends on orb, mavlink) -# -commander start - -# -# Start GPS interface (depends on orb) -# -gps start - -# -# Start the attitude estimator (depends on orb) -# -attitude_estimator_ekf start - -# -# Load mixer and start controllers (depends on px4io) -# -mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix -multirotor_att_control start - -# -# Start logging -# -sdlog2 start -r 20 -a -b 16 - -# -# Start system state -# -if blinkm start -then - blinkm systemstate -fi diff --git a/ROMFS/px4fmu_common/init.d/11_dji_f450 b/ROMFS/px4fmu_common/init.d/11_dji_f450 new file mode 100644 index 000000000..818f9375e --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/11_dji_f450 @@ -0,0 +1,83 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on DJI F450" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.004 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.12 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 7.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.0 + param set MC_YAWRATE_D 0.005 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_P 0.3 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + commander start + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix + +# +# Set PWM output frequency +# +pwm rate -c 1234 -r 400 + +# +# Set disarmed, min and max PWM signals (for DJI ESCs) +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1200 +pwm max -c 1234 -p 1800 + +# +# Start common multirotor apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/12-13_hex b/ROMFS/px4fmu_common/init.d/12-13_hex new file mode 100644 index 000000000..f83f6cfd0 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/12-13_hex @@ -0,0 +1,98 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on Hex" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.004 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.12 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 7.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.0 + param set MC_YAWRATE_D 0.005 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_P 0.3 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.7 + param set MPC_THR_MIN 0.3 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE list: https://pixhawk.ethz.ch/mavlink/ +# 13 = hexarotor +# +param set MAV_TYPE 13 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer +# +mixer load /dev/pwm_output /etc/mixers/FMU_hex_x.mix + +# +# Set PWM output frequency to 400 Hz +# +pwm rate -c 123456 -r 400 + +# +# Set disarmed, min and max PWM signals +# +pwm disarmed -c 123456 -p 900 +pwm min -c 123456 -p 1100 +pwm max -c 123456 -p 1900 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/15_tbs_discovery b/ROMFS/px4fmu_common/init.d/15_tbs_discovery new file mode 100644 index 000000000..c79e9d283 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/15_tbs_discovery @@ -0,0 +1,81 @@ +#!nsh + +echo "[init] Team Blacksheep Discovery Quad" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.006 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.17 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 5.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.15 + param set MC_YAWPOS_P 0.5 + param set MC_YAWRATE_D 0.0 + param set MC_YAWRATE_I 0.0 + param set MC_YAWRATE_P 0.2 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load the mixer for a quad with wide arms +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_w.mix + +# +# Set PWM output frequency +# +pwm rate -c 1234 -r 400 + +# +# Set disarmed, min and max PWM signals +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1100 +pwm max -c 1234 -p 1900 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/16_3dr_iris b/ROMFS/px4fmu_common/init.d/16_3dr_iris new file mode 100644 index 000000000..6be917878 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/16_3dr_iris @@ -0,0 +1,81 @@ +#!nsh + +echo "[init] 3DR Iris Quad" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.004 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.13 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 9.0 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.15 + param set MC_YAWPOS_P 0.5 + param set MC_YAWRATE_D 0.0 + param set MC_YAWRATE_I 0.0 + param set MC_YAWRATE_P 0.2 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.0098 + set EXIT_ON_END yes +fi + +# +# Load the mixer for a quad with wide arms +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_w.mix + +# +# Set PWM output frequency +# +pwm rate -c 1234 -r 400 + +# +# Set disarmed, min and max PWM signals +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1200 +pwm max -c 1234 -p 1800 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/30_io_camflyer b/ROMFS/px4fmu_common/init.d/30_io_camflyer index 5090b98a4..8a8bc1590 100644 --- a/ROMFS/px4fmu_common/init.d/30_io_camflyer +++ b/ROMFS/px4fmu_common/init.d/30_io_camflyer @@ -1,26 +1,6 @@ #!nsh -# -# Flight startup script for PX4FMU+PX4IO -# - -# disable USB and autostart -set USB no -set MODE custom - -# -# Start the ORB (first app to start) -# -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi + +echo "[init] PX4FMU v1, v2 with or without IO on Camflyer" # # Load default params for this platform @@ -28,94 +8,58 @@ fi if param compare SYS_AUTOCONFIG 1 then # Set all params here, then disable autoconfig + # TODO + param set SYS_AUTOCONFIG 0 - param save /fs/microsd/params + param save fi # # Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ +# MAV_TYPE 1 = fixed wing # param set MAV_TYPE 1 - + +set EXIT_ON_END no + # -# Check if PX4IO Firmware should be upgraded (from Andrew Tridgell) +# Start and configure PX4IO or FMU interface # -if [ -f /fs/microsd/px4io.bin ] +if px4io detect then - echo "PX4IO Firmware found. Checking Upgrade.." - if cmp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - then - echo "No newer version, skipping upgrade." - else - echo "Loading /fs/microsd/px4io.bin" - if px4io update /fs/microsd/px4io.bin > /fs/microsd/px4io_update.log - then - cp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - echo "Flashed /fs/microsd/px4io.bin OK" >> /fs/microsd/px4io_update.log - else - echo "Failed flashing /fs/microsd/px4io.bin" >> /fs/microsd/px4io_update.log - echo "Failed to upgrade PX4IO firmware - check if PX4IO is in bootloader mode" - fi - fi + # Start MAVLink (depends on orb) + mavlink start + + sh /etc/init.d/rc.io + # Limit to 100 Hz updates and (implicit) 50 Hz PWM + px4io limit 100 +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes fi - -# -# Start MAVLink (depends on orb) -# -mavlink start -d /dev/ttyS1 -b 57600 -usleep 5000 - -# -# Start the commander (depends on orb, mavlink) -# -commander start - -# -# Start PX4IO interface (depends on orb, commander) -# -px4io start - -# -# Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. -px4io recovery # -# Set actuator limit to 100 Hz update (50 Hz PWM) -px4io limit 100 - -# -# Start the sensors (depends on orb, px4io) -# -sh /etc/init.d/rc.sensors - -# -# Start GPS interface (depends on orb) -# -gps start - -# -# Start the attitude estimator (depends on orb) -# -kalman_demo start - -# # Load mixer and start controllers (depends on px4io) # -mixer load /dev/pwm_output /etc/mixers/FMU_Q.mix -control_demo start - -# -# Start logging -# -sdlog2 start -r 50 -a -b 14 - +if [ -f /fs/microsd/etc/mixers/FMU_Q.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_Q.mix +else + echo "Using /etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_Q.mix +fi + # -# Start system state +# Start common fixedwing apps # -if blinkm start +sh /etc/init.d/rc.fixedwing + +if [ $EXIT_ON_END == yes ] then - blinkm systemstate -fi + exit +fi
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/31_io_phantom b/ROMFS/px4fmu_common/init.d/31_io_phantom index 5090b98a4..63cd7f9b2 100644 --- a/ROMFS/px4fmu_common/init.d/31_io_phantom +++ b/ROMFS/px4fmu_common/init.d/31_io_phantom @@ -1,26 +1,6 @@ #!nsh -# -# Flight startup script for PX4FMU+PX4IO -# - -# disable USB and autostart -set USB no -set MODE custom - -# -# Start the ORB (first app to start) -# -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi + +echo "[init] PX4FMU v1, v2 with or without IO on Phantom FPV" # # Load default params for this platform @@ -28,94 +8,80 @@ fi if param compare SYS_AUTOCONFIG 1 then # Set all params here, then disable autoconfig + param set FW_P_D 0 + param set FW_P_I 0 + param set FW_P_IMAX 15 + param set FW_P_LIM_MAX 50 + param set FW_P_LIM_MIN -50 + param set FW_P_P 60 + param set FW_P_RMAX_NEG 0 + param set FW_P_RMAX_POS 0 + param set FW_P_ROLLFF 1.1 + param set FW_R_D 0 + param set FW_R_I 5 + param set FW_R_IMAX 20 + param set FW_R_P 100 + param set FW_R_RMAX 100 + param set FW_THR_CRUISE 0.65 + param set FW_THR_MAX 1 + param set FW_THR_MIN 0 + param set FW_T_SINK_MAX 5.0 + param set FW_T_SINK_MIN 4.0 + param set FW_Y_ROLLFF 1.1 + param set FW_L1_PERIOD 17 + param set RC_SCALE_ROLL 1.0 + param set RC_SCALE_PITCH 1.0 + param set SYS_AUTOCONFIG 0 - param save /fs/microsd/params + param save fi # # Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ +# MAV_TYPE 1 = fixed wing # param set MAV_TYPE 1 - + +set EXIT_ON_END no + # -# Check if PX4IO Firmware should be upgraded (from Andrew Tridgell) +# Start and configure PX4IO or FMU interface # -if [ -f /fs/microsd/px4io.bin ] +if px4io detect then - echo "PX4IO Firmware found. Checking Upgrade.." - if cmp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - then - echo "No newer version, skipping upgrade." - else - echo "Loading /fs/microsd/px4io.bin" - if px4io update /fs/microsd/px4io.bin > /fs/microsd/px4io_update.log - then - cp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - echo "Flashed /fs/microsd/px4io.bin OK" >> /fs/microsd/px4io_update.log - else - echo "Failed flashing /fs/microsd/px4io.bin" >> /fs/microsd/px4io_update.log - echo "Failed to upgrade PX4IO firmware - check if PX4IO is in bootloader mode" - fi - fi + # Start MAVLink (depends on orb) + mavlink start + + sh /etc/init.d/rc.io + # Limit to 100 Hz updates and (implicit) 50 Hz PWM + px4io limit 100 +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes fi - -# -# Start MAVLink (depends on orb) -# -mavlink start -d /dev/ttyS1 -b 57600 -usleep 5000 - -# -# Start the commander (depends on orb, mavlink) -# -commander start - -# -# Start PX4IO interface (depends on orb, commander) -# -px4io start - -# -# Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. -px4io recovery # -# Set actuator limit to 100 Hz update (50 Hz PWM) -px4io limit 100 - -# -# Start the sensors (depends on orb, px4io) -# -sh /etc/init.d/rc.sensors - -# -# Start GPS interface (depends on orb) -# -gps start - -# -# Start the attitude estimator (depends on orb) -# -kalman_demo start - -# # Load mixer and start controllers (depends on px4io) # -mixer load /dev/pwm_output /etc/mixers/FMU_Q.mix -control_demo start - -# -# Start logging -# -sdlog2 start -r 50 -a -b 14 - +if [ -f /fs/microsd/etc/mixers/FMU_Q.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_Q.mix +else + echo "Using /etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_Q.mix +fi + # -# Start system state +# Start common fixedwing apps # -if blinkm start +sh /etc/init.d/rc.fixedwing + +if [ $EXIT_ON_END == yes ] then - blinkm systemstate -fi + exit +fi
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/32_skywalker_x5 b/ROMFS/px4fmu_common/init.d/32_skywalker_x5 new file mode 100644 index 000000000..1e752f13a --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/32_skywalker_x5 @@ -0,0 +1,65 @@ +#!nsh + +echo "[init] PX4FMU v1, v2 with or without IO on Skywalker X5" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + # TODO + + param set SYS_AUTOCONFIG 0 + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 1 = fixed wing +# +param set MAV_TYPE 1 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + + sh /etc/init.d/rc.io + # Limit to 100 Hz updates and (implicit) 50 Hz PWM + px4io limit 100 +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer and start controllers (depends on px4io) +# +if [ -f /fs/microsd/etc/mixers/FMU_Q.mix ] +then + echo "Using /fs/microsd/etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /fs/microsd/etc/mixers/FMU_Q.mix +else + echo "Using /etc/mixers/FMU_Q.mix" + mixer load /dev/pwm_output /etc/mixers/FMU_Q.mix +fi + +# +# Start common fixedwing apps +# +sh /etc/init.d/rc.fixedwing + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/40_io_segway b/ROMFS/px4fmu_common/init.d/40_io_segway index 5742d685a..fb9dec043 100644 --- a/ROMFS/px4fmu_common/init.d/40_io_segway +++ b/ROMFS/px4fmu_common/init.d/40_io_segway @@ -1,26 +1,4 @@ #!nsh -# -# Flight startup script for PX4FMU+PX4IO -# - -# disable USB and autostart -set USB no -set MODE custom - -# -# Start the ORB (first app to start) -# -uorb start - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi # # Load default params for this platform @@ -28,39 +6,18 @@ fi if param compare SYS_AUTOCONFIG 1 then # Set all params here, then disable autoconfig + # TODO + param set SYS_AUTOCONFIG 0 - param save /fs/microsd/params + param save fi # # Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ +# MAV_TYPE 10 = ground rover # param set MAV_TYPE 10 - -# -# Check if PX4IO Firmware should be upgraded (from Andrew Tridgell) -# -if [ -f /fs/microsd/px4io.bin ] -then - echo "PX4IO Firmware found. Checking Upgrade.." - if cmp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - then - echo "No newer version, skipping upgrade." - else - echo "Loading /fs/microsd/px4io.bin" - if px4io update /fs/microsd/px4io.bin > /fs/microsd/px4io_update.log - then - cp /fs/microsd/px4io.bin /fs/microsd/px4io.bin.current - echo "Flashed /fs/microsd/px4io.bin OK" >> /fs/microsd/px4io_update.log - else - echo "Failed flashing /fs/microsd/px4io.bin" >> /fs/microsd/px4io_update.log - echo "Failed to upgrade PX4IO firmware - check if PX4IO is in bootloader mode" - fi - fi -fi - + # # Start MAVLink (depends on orb) # @@ -68,26 +25,16 @@ mavlink start -d /dev/ttyS1 -b 57600 usleep 5000 # -# Start the commander (depends on orb, mavlink) +# Start and configure PX4IO interface # -commander start +sh /etc/init.d/rc.io # -# Start PX4IO interface (depends on orb, commander) -# -px4io start - +# Start the commander (depends on orb, mavlink) # -# Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. -px4io recovery +commander start # -# Disable px4io topic limiting -# -px4io limit 200 - -# # Start the sensors (depends on orb, px4io) # sh /etc/init.d/rc.sensors @@ -105,18 +52,5 @@ attitude_estimator_ekf start # # Load mixer and start controllers (depends on px4io) # -md25 start 3 0x58 +roboclaw start /dev/ttyS2 128 1200 segway start - -# -# Start logging -# -sdlog2 start -r 50 -a -b 14 - -# -# Start system state -# -if blinkm start -then - blinkm systemstate -fi diff --git a/ROMFS/px4fmu_common/init.d/666_fmu_q_x550 b/ROMFS/px4fmu_common/init.d/666_fmu_q_x550 new file mode 100644 index 000000000..1ee84b9b0 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/666_fmu_q_x550 @@ -0,0 +1,83 @@ +#!nsh + +echo "[init] 666_fmu_q_x550: PX4FMU Quad X550 with or without IO" + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set MC_ATTRATE_P 0.14 + param set MC_ATTRATE_I 0 + param set MC_ATTRATE_D 0.006 + param set MC_ATT_P 5.5 + param set MC_ATT_I 0 + param set MC_ATT_D 0 + param set MC_YAWPOS_D 0 + param set MC_YAWPOS_I 0 + param set MC_YAWPOS_P 0.6 + param set MC_YAWRATE_D 0 + param set MC_YAWRATE_I 0 + param set MC_YAWRATE_P 0.08 + param set RC_SCALE_PITCH 1 + param set RC_SCALE_ROLL 1 + param set RC_SCALE_YAW 3 + + param set SYS_AUTOCONFIG 0 + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer +# +mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix + +# +# Set PWM output frequency +# +pwm rate -c 1234 -r 400 + +# +# Set disarmed, min and max PWM signals +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1100 +pwm max -c 1234 -p 1900 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/cmp_test b/ROMFS/px4fmu_common/init.d/cmp_test new file mode 100644 index 000000000..f86f4f85b --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/cmp_test @@ -0,0 +1,9 @@ +#!nsh + +cp /etc/extras/px4io-v2_default.bin /fs/microsd/px4io.loaded +if cmp /etc/extras/px4io-v2_default.bin /fs/microsd/px4io.loaded +then + echo "CMP returned true" +else + echo "CMP returned false" +fi
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/rc.boarddetect b/ROMFS/px4fmu_common/init.d/rc.boarddetect deleted file mode 100644 index f233e51df..000000000 --- a/ROMFS/px4fmu_common/init.d/rc.boarddetect +++ /dev/null @@ -1,66 +0,0 @@ -#!nsh -# -# If we are still in flight mode, work out what airframe -# configuration we have and start up accordingly. -# -if [ $MODE != autostart ] -then - echo "[init] automatic startup cancelled by user script" -else - echo "[init] detecting attached hardware..." - - # - # Assume that we are PX4FMU in standalone mode - # - set BOARD PX4FMU - - # - # Are we attached to a PX4IOAR (AR.Drone carrier board)? - # - if boardinfo test name PX4IOAR - then - set BOARD PX4IOAR - if [ -f /etc/init.d/rc.PX4IOAR ] - then - echo "[init] reading /etc/init.d/rc.PX4IOAR" - usleep 500 - sh /etc/init.d/rc.PX4IOAR - fi - else - echo "[init] PX4IOAR not detected" - fi - - # - # Are we attached to a PX4IO? - # - if boardinfo test name PX4IO - then - set BOARD PX4IO - if [ -f /etc/init.d/rc.PX4IO ] - then - echo "[init] reading /etc/init.d/rc.PX4IO" - usleep 500 - sh /etc/init.d/rc.PX4IO - fi - else - echo "[init] PX4IO not detected" - fi - - # - # Looks like we are stand-alone - # - if [ $BOARD == PX4FMU ] - then - echo "[init] no expansion board detected" - if [ -f /etc/init.d/rc.standalone ] - then - echo "[init] reading /etc/init.d/rc.standalone" - sh /etc/init.d/rc.standalone - fi - fi - - # - # We may not reach here if the airframe-specific script exits the shell. - # - echo "[init] startup done." -fi
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/rc.custom_dji_f330_mkblctrl b/ROMFS/px4fmu_common/init.d/rc.custom_dji_f330_mkblctrl new file mode 100644 index 000000000..4686382ca --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.custom_dji_f330_mkblctrl @@ -0,0 +1,120 @@ +#!nsh + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.002 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.09 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 6.8 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.0 + param set MC_YAWRATE_D 0.005 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_P 0.3 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.7 + param set MPC_THR_MIN 0.3 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +# +# Start the Mikrokopter ESC driver +# +if [ $MKBLCTRL_MODE == yes ] +then + if [ $MKBLCTRL_FRAME == x ] + then + echo "[init] PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame Mikrokopter-Addressing" + mkblctrl -mkmode x + else + echo "[init] PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame Mikrokopter-Addressing" + mkblctrl -mkmode + + fi +else + if [ $MKBLCTRL_FRAME == x ] + then + echo "[init] PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame" + else + echo "[init] PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame" + fi + mkblctrl +fi + +usleep 10000 + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start + usleep 5000 + + sh /etc/init.d/rc.io +else + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS0 + usleep 5000 + fmu mode_pwm + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +# +# Load mixer +# +if [ $MKBLCTRL_FRAME == x ] +then + mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix +else + mixer load /dev/pwm_output /etc/mixers/FMU_quad_+.mix +fi + +# +# Set disarmed, min and max PWM signals +# +pwm disarmed -c 1234 -p 900 +pwm min -c 1234 -p 1200 +pwm max -c 1234 -p 1800 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi diff --git a/ROMFS/px4fmu_common/init.d/rc.custom_io_esc b/ROMFS/px4fmu_common/init.d/rc.custom_io_esc new file mode 100644 index 000000000..045e41e52 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.custom_io_esc @@ -0,0 +1,120 @@ +#!nsh + +# +# Load default params for this platform +# +if param compare SYS_AUTOCONFIG 1 +then + # Set all params here, then disable autoconfig + param set SYS_AUTOCONFIG 0 + + param set MC_ATTRATE_D 0.002 + param set MC_ATTRATE_I 0.0 + param set MC_ATTRATE_P 0.09 + param set MC_ATT_D 0.0 + param set MC_ATT_I 0.0 + param set MC_ATT_P 6.8 + param set MC_YAWPOS_D 0.0 + param set MC_YAWPOS_I 0.0 + param set MC_YAWPOS_P 2.0 + param set MC_YAWRATE_D 0.005 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_P 0.3 + param set NAV_TAKEOFF_ALT 3.0 + param set MPC_TILT_MAX 0.5 + param set MPC_THR_MAX 0.7 + param set MPC_THR_MIN 0.3 + param set MPC_XY_D 0 + param set MPC_XY_P 0.5 + param set MPC_XY_VEL_D 0 + param set MPC_XY_VEL_I 0 + param set MPC_XY_VEL_MAX 3 + param set MPC_XY_VEL_P 0.2 + param set MPC_Z_D 0 + param set MPC_Z_P 1 + param set MPC_Z_VEL_D 0 + param set MPC_Z_VEL_I 0.1 + param set MPC_Z_VEL_MAX 2 + param set MPC_Z_VEL_P 0.20 + + param save +fi + +echo "RC script for PX4FMU + PX4IO + PPM-ESCs running" + +# +# Force some key parameters to sane values +# MAV_TYPE 2 = quadrotor +# +param set MAV_TYPE 2 + +set EXIT_ON_END no + +usleep 10000 + +# +# Start and configure PX4IO or FMU interface +# +if px4io detect +then + # Start MAVLink (depends on orb) + mavlink start -d /dev/ttyS1 -b 57600 + usleep 5000 + + sh /etc/init.d/rc.io +else + fmu mode_pwm + # Start MAVLink (on UART1 / ttyS0) + mavlink start -d /dev/ttyS1 -b 57600 + usleep 5000 + param set BAT_V_SCALING 0.004593 + set EXIT_ON_END yes +fi + +if [ $ESC_MAKER = afro ] +then + # Set PWM values for Afro ESCs + pwm disarmed -c 1234 -p 1050 + pwm min -c 1234 -p 1080 + pwm max -c 1234 -p 1860 +else + # Set PWM values for typical ESCs + pwm disarmed -c 1234 -p 900 + pwm min -c 1234 -p 980 + pwm max -c 1234 -p 1800 +fi + +# +# Load mixer +# +if [ $FRAME_GEOMETRY == x ] +then + echo "Frame geometry X" + mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix +else + if [ $FRAME_GEOMETRY == w ] + then + echo "Frame geometry W" + mixer load /dev/pwm_output /etc/mixers/FMU_quad_w.mix + else + echo "Frame geometry +" + mixer load /dev/pwm_output /etc/mixers/FMU_quad_+.mix + fi +fi + +# +# Set PWM output frequency +# +pwm rate -r 400 -c 1234 + +# +# Start common for all multirotors apps +# +sh /etc/init.d/rc.multirotor + +if [ $EXIT_ON_END == yes ] +then + exit +fi + +echo "Script end" diff --git a/ROMFS/px4fmu_common/init.d/rc.fixedwing b/ROMFS/px4fmu_common/init.d/rc.fixedwing new file mode 100644 index 000000000..f02851006 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.fixedwing @@ -0,0 +1,34 @@ +#!nsh +# +# Standard everything needed for fixedwing except mixer, actuator output and mavlink +# + +# +# Start the sensors and test them. +# +sh /etc/init.d/rc.sensors + +# +# Start logging (depends on sensors) +# +sh /etc/init.d/rc.logging + +# +# Start GPS interface (depends on orb) +# +gps start + +# +# Start the attitude and position estimator +# +att_pos_estimator_ekf start + +# +# Start attitude controller +# +fw_att_control start + +# +# Start the position controller +# +fw_pos_control_l1 start diff --git a/ROMFS/px4fmu_common/init.d/rc.hil b/ROMFS/px4fmu_common/init.d/rc.hil deleted file mode 100644 index 3517a5bd8..000000000 --- a/ROMFS/px4fmu_common/init.d/rc.hil +++ /dev/null @@ -1,68 +0,0 @@ -#!nsh -# -# USB HIL start -# - -echo "[HIL] starting.." - -uorb start - -# Tell MAVLink that this link is "fast" -mavlink start -b 230400 -d /dev/console - -# Create a fake HIL /dev/pwm_output interface -hil mode_pwm - -# -# Load microSD params -# -echo "[init] loading microSD params" -param select /fs/microsd/params -if [ -f /fs/microsd/params ] -then - param load /fs/microsd/params -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 1 = fixed wing, 2 = quadrotor, 13 = hexarotor -# see https://pixhawk.ethz.ch/mavlink/ -# -param set MAV_TYPE 1 - -# -# Start the commander (depends on orb, mavlink) -# -commander start - -# -# Check if we got an IO -# -if [ px4io start ] -then - echo "IO started" -else - fmu mode_serial - echo "FMU started" -end - -# -# Start the sensors (depends on orb, px4io) -# -sh /etc/init.d/rc.sensors - -# -# Start the attitude estimator (depends on orb) -# -att_pos_estimator_ekf start - -# -# Load mixer and start controllers (depends on px4io) -# -mixer load /dev/pwm_output /etc/mixers/FMU_AET.mix -fixedwing_backside start - -echo "[HIL] setup done, running" - -# Exit shell to make it available to MAVLink -exit diff --git a/ROMFS/px4fmu_common/init.d/rc.io b/ROMFS/px4fmu_common/init.d/rc.io new file mode 100644 index 000000000..aaf91b316 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.io @@ -0,0 +1,23 @@ +# +# Start PX4IO interface (depends on orb, commander) +# +if px4io start +then + # + # Allow PX4IO to recover from midair restarts. + # this is very unlikely, but quite safe and robust. + px4io recovery + + # + # Disable px4io topic limiting + # + if [ $BOARD == fmuv1 ] + then + px4io limit 200 + else + px4io limit 400 + fi +else + # SOS + tone_alarm error +fi diff --git a/ROMFS/px4fmu_common/init.d/rc.logging b/ROMFS/px4fmu_common/init.d/rc.logging index 09c2d00d1..dc4be8055 100644 --- a/ROMFS/px4fmu_common/init.d/rc.logging +++ b/ROMFS/px4fmu_common/init.d/rc.logging @@ -5,5 +5,10 @@ if [ -d /fs/microsd ] then - sdlog start + if [ $BOARD == fmuv1 ] + then + sdlog2 start -r 50 -a -b 16 + else + sdlog2 start -r 200 -a -b 16 + fi fi diff --git a/ROMFS/px4fmu_common/init.d/rc.multirotor b/ROMFS/px4fmu_common/init.d/rc.multirotor new file mode 100644 index 000000000..bc550ac5a --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.multirotor @@ -0,0 +1,39 @@ +#!nsh +# +# Standard everything needed for multirotors except mixer, actuator output and mavlink +# + +# +# Start the sensors and test them. +# +sh /etc/init.d/rc.sensors + +# +# Start logging (depends on sensors) +# +sh /etc/init.d/rc.logging + +# +# Start GPS interface (depends on orb) +# +gps start + +# +# Start the attitude estimator +# +attitude_estimator_ekf start + +# +# Start position estimator +# +position_estimator_inav start + +# +# Start attitude control +# +multirotor_att_control start + +# +# Start position control +# +multirotor_pos_control start diff --git a/ROMFS/px4fmu_common/init.d/rc.sensors b/ROMFS/px4fmu_common/init.d/rc.sensors index 5e80ddc2f..f17b650bc 100644 --- a/ROMFS/px4fmu_common/init.d/rc.sensors +++ b/ROMFS/px4fmu_common/init.d/rc.sensors @@ -7,25 +7,40 @@ # Start sensor drivers here. # -# -# Check for UORB -# -if uorb start -then - echo "uORB started" -fi - ms5611 start adc start +# mag might be external +if hmc5883 start +then + echo "using HMC5883" +fi + if mpu6000 start then - echo "using MPU6000 and HMC5883L" - hmc5883 start + echo "using MPU6000" + set BOARD fmuv1 else echo "using L3GD20 and LSM303D" l3gd20 start lsm303d start + set BOARD fmuv2 +fi + +# Start airspeed sensors +if meas_airspeed start +then + echo "using MEAS airspeed sensor" +else + if ets_airspeed start + then + echo "using ETS airspeed sensor (bus 3)" + else + if ets_airspeed start -b 1 + then + echo "Using ETS airspeed sensor (bus 1)" + fi + fi fi # @@ -36,8 +51,5 @@ fi # if sensors start then - # - # Check sensors - run AFTER 'sensors start' - # preflight_check & fi diff --git a/ROMFS/px4fmu_common/init.d/rc.usb b/ROMFS/px4fmu_common/init.d/rc.usb index 5b1bd272e..ccf2cd47e 100644 --- a/ROMFS/px4fmu_common/init.d/rc.usb +++ b/ROMFS/px4fmu_common/init.d/rc.usb @@ -8,14 +8,28 @@ echo "Starting MAVLink on this USB console" # Stop tone alarm tone_alarm stop +# +# Check for UORB +# +if uorb start +then + echo "uORB started" +fi + # Tell MAVLink that this link is "fast" if mavlink stop then echo "stopped other MAVLink instance" fi -sleep 2 mavlink start -b 230400 -d /dev/ttyACM0 +# Stop commander +if commander stop +then + echo "Commander stopped" +fi +sleep 1 + # Start the commander if commander start then diff --git a/ROMFS/px4fmu_common/init.d/rcS b/ROMFS/px4fmu_common/init.d/rcS index f0ee1a0c6..d8b5cb608 100755 --- a/ROMFS/px4fmu_common/init.d/rcS +++ b/ROMFS/px4fmu_common/init.d/rcS @@ -20,7 +20,7 @@ then else echo "[init] no microSD card found" # Play SOS - tone_alarm 2 + tone_alarm error fi # @@ -57,90 +57,301 @@ fi if [ $MODE == autostart ] then + # + # Start terminal + # + if sercon + then + echo "USB connected" + fi + + # + # Start the ORB (first app to start) + # + uorb start + + # + # Load microSD params + # + #if ramtron start + #then + # param select /ramtron/params + # if [ -f /ramtron/params ] + # then + # param load /ramtron/params + # fi + #else + param select /fs/microsd/params + if [ -f /fs/microsd/params ] + then + if param load /fs/microsd/params + then + echo "Parameters loaded" + else + echo "Parameter file corrupt - ignoring" + fi + fi + #fi + + # + # Start system state indicator + # + if rgbled start + then + echo "Using external RGB Led" + else + if blinkm start + then + blinkm systemstate + fi + fi + + # + # Start the Commander (needs to be this early for in-air-restarts) + # + commander start -# -# Start the ORB (first app to start) -# -uorb start + if param compare SYS_AUTOSTART 1000 + then + sh /etc/init.d/1000_rc_fw_easystar.hil + set MODE custom + fi + + if param compare SYS_AUTOSTART 1001 + then + sh /etc/init.d/1001_rc_quad.hil + set MODE custom + fi + + if param compare SYS_AUTOSTART 1002 + then + sh /etc/init.d/1002_rc_fw_state.hil + set MODE custom + fi + + if param compare SYS_AUTOSTART 1003 + then + sh /etc/init.d/1003_rc_quad_+.hil + set MODE custom + fi -# -# Load microSD params -# -if ramtron start -then - param select /ramtron/params - if [ -f /ramtron/params ] + if param compare SYS_AUTOSTART 1004 then - param load /ramtron/params + sh /etc/init.d/1004_rc_fw_Rascal110.hil + set MODE custom fi -else - param select /fs/microsd/params - if [ -f /fs/microsd/params ] + + if [ $MODE != custom ] then - param load /fs/microsd/params + # Try to get an USB console + nshterm /dev/ttyACM0 & fi -fi -# -# Check if PX4IO Firmware should be upgraded (from Andrew Tridgell) -# -if [ -f /fs/microsd/px4io.bin ] -then - echo "PX4IO Firmware found. Checking Upgrade.." - if cmp /fs/microsd/px4io.bin /fs/microsd/px4io.cur + + # + # Upgrade PX4IO firmware + # + if px4io detect then - echo "No newer version, skipping upgrade." + echo "PX4IO running, not upgrading" else - echo "Loading /fs/microsd/px4io.bin" - if px4io update /fs/microsd/px4io.bin > /fs/microsd/px4io.log + echo "Attempting to upgrade PX4IO" + if px4io update then - cp /fs/microsd/px4io.bin /fs/microsd/px4io.cur - echo "Flashed /fs/microsd/px4io.bin OK" >> /fs/microsd/px4io.log + if [ -d /fs/microsd ] + then + echo "Flashed PX4IO Firmware OK" > /fs/microsd/px4io.log + fi + + # Allow IO to safely kick back to app + usleep 200000 else - echo "Failed flashing /fs/microsd/px4io.bin" >> /fs/microsd/px4io.log - echo "Failed to upgrade px4io firmware - check if px4io is in bootloader mode" + echo "No PX4IO to upgrade here" fi fi -fi + + # + # Check if auto-setup from one of the standard scripts is wanted + # SYS_AUTOSTART = 0 means no autostart (default) + # + + if param compare SYS_AUTOSTART 8 + then + sh /etc/init.d/08_ardrone + set MODE custom + fi + + if param compare SYS_AUTOSTART 9 + then + sh /etc/init.d/09_ardrone_flow + set MODE custom + fi + + if param compare SYS_AUTOSTART 10 + then + sh /etc/init.d/10_dji_f330 + set MODE custom + fi -# -# Check if auto-setup from one of the standard scripts is wanted -# SYS_AUTOSTART = 0 means no autostart (default) -# -if param compare SYS_AUTOSTART 1 -then - sh /etc/init.d/01_fmu_quad_x -fi + if param compare SYS_AUTOSTART 11 + then + sh /etc/init.d/11_dji_f450 + set MODE custom + fi -if param compare SYS_AUTOSTART 2 -then - sh /etc/init.d/02_io_quad_x -fi + if param compare SYS_AUTOSTART 12 + then + set MIXER /etc/mixers/FMU_hex_x.mix + sh /etc/init.d/12-13_hex + set MODE custom + fi -if param compare SYS_AUTOSTART 8 -then - sh /etc/init.d/08_ardrone -fi + if param compare SYS_AUTOSTART 13 + then + set MIXER /etc/mixers/FMU_hex_+.mix + sh /etc/init.d/12-13_hex + set MODE custom + fi + + if param compare SYS_AUTOSTART 15 + then + sh /etc/init.d/15_tbs_discovery + set MODE custom + fi -if param compare SYS_AUTOSTART 9 -then - sh /etc/init.d/09_ardrone_flow -fi + if param compare SYS_AUTOSTART 16 + then + sh /etc/init.d/16_3dr_iris + set MODE custom + fi -if param compare SYS_AUTOSTART 10 -then - sh /etc/init.d/10_io_f330 -fi + # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame + if param compare SYS_AUTOSTART 17 + then + set MKBLCTRL_MODE no + set MKBLCTRL_FRAME x + sh /etc/init.d/rc.custom_dji_f330_mkblctrl + set MODE custom + fi -if param compare SYS_AUTOSTART 30 -then - sh /etc/init.d/30_io_camflyer -fi + # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame + if param compare SYS_AUTOSTART 18 + then + set MKBLCTRL_MODE no + set MKBLCTRL_FRAME + + sh /etc/init.d/rc.custom_dji_f330_mkblctrl + set MODE custom + fi -if param compare SYS_AUTOSTART 31 -then - sh /etc/init.d/31_io_phantom -fi + # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 X Frame Mikrokopter-Addressing + if param compare SYS_AUTOSTART 19 + then + set MKBLCTRL_MODE yes + set MKBLCTRL_FRAME x + sh /etc/init.d/rc.custom_dji_f330_mkblctrl + set MODE custom + fi + + # PX4FMU v1, v2 with or without IO and Mikrokopter I2C ESCs on DJI F330 + Frame Mikrokopter-Addressing + if param compare SYS_AUTOSTART 20 + then + set MKBLCTRL_MODE yes + set MKBLCTRL_FRAME + + sh /etc/init.d/rc.custom_dji_f330_mkblctrl + set MODE custom + fi + + # PX4FMU v1 with IO + PPM-based ESCs on Quad X-shape frame + if param compare SYS_AUTOSTART 21 + then + set FRAME_GEOMETRY x + set ESC_MAKER afro + sh /etc/init.d/rc.custom_io_esc + set MODE custom + fi + + # PX4FMU v1 with IO + PPM-based ESCs on Quad X-shape frame + if param compare SYS_AUTOSTART 22 + then + set FRAME_GEOMETRY w + sh /etc/init.d/rc.custom_io_esc + set MODE custom + fi + + if param compare SYS_AUTOSTART 30 + then + sh /etc/init.d/30_io_camflyer + set MODE custom + fi + + if param compare SYS_AUTOSTART 31 + then + sh /etc/init.d/31_io_phantom + set MODE custom + fi + + if param compare SYS_AUTOSTART 32 + then + sh /etc/init.d/32_skywalker_x5 + set MODE custom + fi + + if param compare SYS_AUTOSTART 40 + then + sh /etc/init.d/40_io_segway + set MODE custom + fi + + if param compare SYS_AUTOSTART 100 + then + sh /etc/init.d/100_mpx_easystar + set MODE custom + fi + + if param compare SYS_AUTOSTART 101 + then + sh /etc/init.d/101_hk_bixler + set MODE custom + fi + + # Start any custom extensions that might be missing + if [ -f /fs/microsd/etc/rc.local ] + then + sh /fs/microsd/etc/rc.local + fi + + # If none of the autostart scripts triggered, get a minimal setup + if [ $MODE == autostart ] + then + # Telemetry port is on both FMU boards ttyS1 + # but the AR.Drone motors can be get 'flashed' + # if starting MAVLink on them - so do not + # start it as default (default link: USB) + + # Start commander + commander start + + # Start px4io if present + if px4io detect + then + px4io start + else + if fmu mode_serial + then + echo "FMU driver (no PWM) started" + fi + fi + + # Start sensors + sh /etc/init.d/rc.sensors + + # Start one of the estimators + attitude_estimator_ekf start + + # Start GPS + gps start + + fi # End of autostart fi diff --git a/ROMFS/px4fmu_common/mixers/FMU_AERT.mix b/ROMFS/px4fmu_common/mixers/FMU_AERT.mix index 75e82bb00..0ec663e35 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_AERT.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_AERT.mix @@ -62,3 +62,23 @@ range. Inputs below zero are treated as zero. M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 + + +Gimbal / flaps / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_AET.mix b/ROMFS/px4fmu_common/mixers/FMU_AET.mix index 20cb88b91..c73cb2a62 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_AET.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_AET.mix @@ -58,3 +58,23 @@ range. Inputs below zero are treated as zero. M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 + + +Gimbal / flaps / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_Q.mix b/ROMFS/px4fmu_common/mixers/FMU_Q.mix index ebcb66b24..17ff71151 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_Q.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_Q.mix @@ -50,3 +50,21 @@ M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 +Gimbal / flaps / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_RET.mix b/ROMFS/px4fmu_common/mixers/FMU_RET.mix index 95beb8927..f07c34ac8 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_RET.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_RET.mix @@ -51,3 +51,23 @@ range. Inputs below zero are treated as zero. M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 + + +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_X5.mix b/ROMFS/px4fmu_common/mixers/FMU_X5.mix index 9f81e1dc3..610868354 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_X5.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_X5.mix @@ -48,3 +48,22 @@ M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 + diff --git a/ROMFS/px4fmu_common/mixers/FMU_delta.mix b/ROMFS/px4fmu_common/mixers/FMU_delta.mix index 981466704..f0aa6650d 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_delta.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_delta.mix @@ -48,3 +48,23 @@ M: 1 O: 10000 10000 0 -10000 10000 S: 0 3 0 20000 -10000 -10000 10000 + +Gimbal / flaps / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 + diff --git a/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix b/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix index b5e38ce9e..f8f9f0e4d 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix @@ -5,3 +5,14 @@ This file defines a single mixer for a hexacopter in the + configuration. All co are mixed 100%. R: 6+ 10000 10000 10000 0 + +Gimbal / payload mixer for last two channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix b/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix index 8e8d122ad..26b40b9e9 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix @@ -5,3 +5,14 @@ This file defines a single mixer for a hexacopter in the X configuration. All c are mixed 100%. R: 6x 10000 10000 10000 0 + +Gimbal / payload mixer for last two channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_octo_cox.mix b/ROMFS/px4fmu_common/mixers/FMU_octo_cox.mix new file mode 100644 index 000000000..51cebb785 --- /dev/null +++ b/ROMFS/px4fmu_common/mixers/FMU_octo_cox.mix @@ -0,0 +1,7 @@ +Multirotor mixer for PX4FMU +=========================== + +This file defines a single mixer for a Coaxial Octocopter in the X configuration. All controls +are mixed 100%. + +R: 8c 10000 10000 10000 0 diff --git a/ROMFS/px4fmu_common/mixers/FMU_quad_+.mix b/ROMFS/px4fmu_common/mixers/FMU_quad_+.mix index dfdf1d58e..cd9a9cfab 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_quad_+.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_quad_+.mix @@ -5,3 +5,23 @@ This file defines a single mixer for a quadrotor in the + configuration. All con are mixed 100%. R: 4+ 10000 10000 10000 0 + + +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_quad_v.mix b/ROMFS/px4fmu_common/mixers/FMU_quad_v.mix index 2a4a0f341..520aba635 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_quad_v.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_quad_v.mix @@ -5,3 +5,22 @@ This file defines a single mixer for a quadrotor in the V configuration. All co are mixed 100%. R: 4v 10000 10000 10000 0 + +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_quad_w.mix b/ROMFS/px4fmu_common/mixers/FMU_quad_w.mix index 81b4af30b..58e6af74b 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_quad_w.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_quad_w.mix @@ -4,3 +4,22 @@ Multirotor mixer for PX4FMU This file defines a single mixer for a quadrotor with a wide configuration. All controls are mixed 100%. R: 4w 10000 10000 10000 0 + +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 diff --git a/ROMFS/px4fmu_common/mixers/FMU_quad_x.mix b/ROMFS/px4fmu_common/mixers/FMU_quad_x.mix index 12a3bee20..fa21c8012 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_quad_x.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_quad_x.mix @@ -5,3 +5,22 @@ This file defines a single mixer for a quadrotor in the X configuration. All co are mixed 100%. R: 4x 10000 10000 10000 0 + +Gimbal / payload mixer for last four channels +----------------------------------------------------- + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 4 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 5 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 6 10000 10000 0 -10000 10000 + +M: 1 +O: 10000 10000 0 -10000 10000 +S: 0 7 10000 10000 0 -10000 10000 |