diff options
Diffstat (limited to 'ROMFS')
44 files changed, 294 insertions, 1019 deletions
diff --git a/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil b/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil index ebe8a1a1e..36194ad68 100644 --- a/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil +++ b/ROMFS/px4fmu_common/init.d/1000_rc_fw_easystar.hil @@ -2,44 +2,13 @@ # # HILStar / X-Plane # -# Maintainers: Thomas Gubler <thomasgubler@gmail.com> +# Lorenz Meier <lm@inf.ethz.ch> # -echo "HIL Rascal 110 starting.." - -if [ $DO_AUTOCONFIG == yes ] -then - # Set all params here, then disable autoconfig - - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 +sh /etc/init.d/rc.fw_defaults - param set SYS_AUTOCONFIG 0 - param save -fi +echo "HIL Rascal 110 starting.." set HIL yes -set VEHICLE_TYPE fw set MIXER FMU_AERT diff --git a/ROMFS/px4fmu_common/init.d/10015_tbs_discovery b/ROMFS/px4fmu_common/init.d/10015_tbs_discovery index 63798bb3c..b09765e8e 100644 --- a/ROMFS/px4fmu_common/init.d/10015_tbs_discovery +++ b/ROMFS/px4fmu_common/init.d/10015_tbs_discovery @@ -2,30 +2,11 @@ # # Team Blacksheep Discovery Quadcopter # -# Maintainers: Simon Wilks <sjwilks@gmail.com> +# Simon Wilks <sjwilks@gmail.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 5.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.17 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.006 - param set MC_YAWPOS_P 0.5 - param set MC_YAWPOS_I 0.15 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.2 - param set MC_YAWRATE_I 0.0 - param set MC_YAWRATE_D 0.0 -fi +sh /etc/init.d/rc.mc_defaults -set VEHICLE_TYPE mc set MIXER FMU_quad_w -set PWM_OUTPUTS 1234 -set PWM_RATE 400 +set PWM_OUTPUTS 1234
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/10016_3dr_iris b/ROMFS/px4fmu_common/init.d/10016_3dr_iris index 67c24fab3..42d516993 100644 --- a/ROMFS/px4fmu_common/init.d/10016_3dr_iris +++ b/ROMFS/px4fmu_common/init.d/10016_3dr_iris @@ -2,52 +2,20 @@ # # 3DR Iris Quadcopter # -# Maintainers: Anton Babushkin <anton.babushkin@me.com> +# Anton Babushkin <anton.babushkin@me.com> # +sh /etc/init.d/rc.mc_defaults + if [ $DO_AUTOCONFIG == yes ] then # # Default parameters for this platform # - param set MC_ATT_P 9.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.13 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 0.5 - param set MC_YAWPOS_I 0.15 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.2 - param set MC_YAWRATE_I 0.0 - param set MC_YAWRATE_D 0.0 - - param set MPC_TILT_MAX 0.5 - param set MPC_THR_MAX 0.8 - param set MPC_THR_MIN 0.2 - param set MPC_XY_D 0 - param set MPC_XY_P 0.5 - param set MPC_XY_VEL_D 0 - param set MPC_XY_VEL_I 0 - param set MPC_XY_VEL_MAX 3 - param set MPC_XY_VEL_P 0.2 - param set MPC_Z_D 0 - param set MPC_Z_P 1 - param set MPC_Z_VEL_D 0 - param set MPC_Z_VEL_I 0.1 - param set MPC_Z_VEL_MAX 2 - param set MPC_Z_VEL_P 0.20 - param set BAT_V_SCALING 0.00989 param set BAT_C_SCALING 0.0124 fi -set VEHICLE_TYPE mc set MIXER FMU_quad_w set PWM_OUTPUTS 1234 -set PWM_RATE 400 -set PWM_DISARMED 900 -set PWM_MIN 1000 -set PWM_MAX 2000 diff --git a/ROMFS/px4fmu_common/init.d/1001_rc_quad_x.hil b/ROMFS/px4fmu_common/init.d/1001_rc_quad_x.hil index 8c0797d7c..7a7a9542c 100644 --- a/ROMFS/px4fmu_common/init.d/1001_rc_quad_x.hil +++ b/ROMFS/px4fmu_common/init.d/1001_rc_quad_x.hil @@ -2,45 +2,11 @@ # # HIL Quadcopter X # -# Maintainers: Anton Babushkin <anton.babushkin@me.com> +# Anton Babushkin <anton.babushkin@me.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - param set MPC_TILT_MAX 0.5 - param set MPC_THR_MAX 0.8 - param set MPC_THR_MIN 0.2 - param set MPC_XY_D 0 - param set MPC_XY_P 0.5 - param set MPC_XY_VEL_D 0 - param set MPC_XY_VEL_I 0 - param set MPC_XY_VEL_MAX 3 - param set MPC_XY_VEL_P 0.2 - param set MPC_Z_D 0 - param set MPC_Z_P 1 - param set MPC_Z_VEL_D 0 - param set MPC_Z_VEL_I 0.1 - param set MPC_Z_VEL_MAX 2 - param set MPC_Z_VEL_P 0.20 -fi +sh /etc/init.d/rc.mc_defaults -set HIL yes - -set VEHICLE_TYPE mc set MIXER FMU_quad_x + +set HIL yes diff --git a/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil b/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil deleted file mode 100644 index 46da24d35..000000000 --- a/ROMFS/px4fmu_common/init.d/1002_rc_fw_state.hil +++ /dev/null @@ -1,45 +0,0 @@ -#!nsh -# -# HIL Rascal 110 (Flightgear) -# -# Maintainers: Thomas Gubler <thomasgubler@gmail.com> -# - -echo "HIL Rascal 110 starting.." - -if [ $DO_AUTOCONFIG == yes ] -then - # Set all params here, then disable autoconfig - - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 - - param set SYS_AUTOCONFIG 0 - param save -fi - -set HIL yes - -set VEHICLE_TYPE fw -set MIXER FMU_AERT diff --git a/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil b/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil index bce3015fc..c47500c7a 100644 --- a/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil +++ b/ROMFS/px4fmu_common/init.d/1003_rc_quad_+.hil @@ -2,45 +2,11 @@ # # HIL Quadcopter + # -# Maintainers: Anton Babushkin <anton.babushkin@me.com> +# Anton Babushkin <anton.babushkin@me.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - param set MPC_TILT_MAX 0.5 - param set MPC_THR_MAX 0.8 - param set MPC_THR_MIN 0.2 - param set MPC_XY_D 0 - param set MPC_XY_P 0.5 - param set MPC_XY_VEL_D 0 - param set MPC_XY_VEL_I 0 - param set MPC_XY_VEL_MAX 3 - param set MPC_XY_VEL_P 0.2 - param set MPC_Z_D 0 - param set MPC_Z_P 1 - param set MPC_Z_VEL_D 0 - param set MPC_Z_VEL_I 0.1 - param set MPC_Z_VEL_MAX 2 - param set MPC_Z_VEL_P 0.20 -fi +sh /etc/init.d/rc.mc_defaults -set HIL yes - -set VEHICLE_TYPE mc set MIXER FMU_quad_+ + +set HIL yes
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil b/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil index 46da24d35..4e3e18326 100644 --- a/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil +++ b/ROMFS/px4fmu_common/init.d/1004_rc_fw_Rascal110.hil @@ -2,44 +2,13 @@ # # HIL Rascal 110 (Flightgear) # -# Maintainers: Thomas Gubler <thomasgubler@gmail.com> +# Thomas Gubler <thomasgubler@gmail.com> # -echo "HIL Rascal 110 starting.." - -if [ $DO_AUTOCONFIG == yes ] -then - # Set all params here, then disable autoconfig - - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 +sh /etc/init.d/rc.fw_defaults - param set SYS_AUTOCONFIG 0 - param save -fi +echo "HIL Rascal 110 starting.." set HIL yes -set VEHICLE_TYPE fw set MIXER FMU_AERT diff --git a/ROMFS/px4fmu_common/init.d/1005_rc_fw_Malolo1.hil b/ROMFS/px4fmu_common/init.d/1005_rc_fw_Malolo1.hil new file mode 100644 index 000000000..c753ded23 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/1005_rc_fw_Malolo1.hil @@ -0,0 +1,47 @@ +#!nsh +# +# HIL Malolo 1 (Flightgear) +# +# Thomas Gubler <thomasgubler@gmail.com> +# + +sh /etc/init.d/rc.fw_defaults + +if [ $DO_AUTOCONFIG == yes ] +then + param set FW_AIRSPD_MIN 12 + param set FW_AIRSPD_TRIM 25 + param set FW_AIRSPD_MAX 40 + param set FW_ATT_TC 0.3 + param set FW_L1_DAMPING 0.74 + param set FW_L1_PERIOD 15 + param set FW_PR_FF 0.8 + param set FW_PR_I 0.05 + param set FW_PR_IMAX 0.2 + param set FW_PR_P 0.1 + param set FW_P_ROLLFF 0 + param set FW_RR_FF 0.6 + param set FW_RR_I 0.02 + param set FW_RR_IMAX 0.2 + param set FW_RR_P 0.1 + param set FW_R_LIM 45 + param set FW_R_RMAX 0 + param set FW_T_CLMB_MAX 5 + param set FW_T_HRATE_P 0.02 + param set FW_T_PTCH_DAMP 0 + param set FW_T_RLL2THR 15 + param set FW_T_SINK_MAX 5 + param set FW_T_SINK_MIN 2 + param set FW_T_SRATE_P 0.01 + param set FW_T_TIME_CONST 3 + param set FW_T_VERT_ACC 7 + param set FW_YR_FF 0.0 + param set FW_YR_I 0 + param set FW_YR_IMAX 0.2 + param set FW_YR_P 0.0 +fi + +set HIL yes + +# Set the AERT mixer for HIL (even if the malolo is a flying wing) +set MIXER FMU_AERT diff --git a/ROMFS/px4fmu_common/init.d/2100_mpx_easystar b/ROMFS/px4fmu_common/init.d/2100_mpx_easystar index 0e5bf60d6..465a22c53 100644 --- a/ROMFS/px4fmu_common/init.d/2100_mpx_easystar +++ b/ROMFS/px4fmu_common/init.d/2100_mpx_easystar @@ -2,38 +2,7 @@ # # MPX EasyStar Plane # -# Maintainers: ??? -# -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 -fi +sh /etc/init.d/rc.fw_defaults -set VEHICLE_TYPE fw set MIXER FMU_RET diff --git a/ROMFS/px4fmu_common/init.d/2101_hk_bixler b/ROMFS/px4fmu_common/init.d/2101_hk_bixler index 1ed923b19..dcc5db824 100644 --- a/ROMFS/px4fmu_common/init.d/2101_hk_bixler +++ b/ROMFS/px4fmu_common/init.d/2101_hk_bixler @@ -1,40 +1,5 @@ #!nsh -echo "[init] PX4FMU v1, v2 with or without IO on 3DR SkyWalker" +sh /etc/init.d/rc.fw_defaults -# -# Load default params for this platform -# -if [ $DO_AUTOCONFIG == yes ] -then - # Set all params here, then disable autoconfig - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 - - param set SYS_AUTOCONFIG 0 - param save -fi - -set VEHICLE_TYPE fw set MIXER FMU_AERT
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/2102_3dr_skywalker b/ROMFS/px4fmu_common/init.d/2102_3dr_skywalker index 1ed923b19..dcc5db824 100644 --- a/ROMFS/px4fmu_common/init.d/2102_3dr_skywalker +++ b/ROMFS/px4fmu_common/init.d/2102_3dr_skywalker @@ -1,40 +1,5 @@ #!nsh -echo "[init] PX4FMU v1, v2 with or without IO on 3DR SkyWalker" +sh /etc/init.d/rc.fw_defaults -# -# Load default params for this platform -# -if [ $DO_AUTOCONFIG == yes ] -then - # Set all params here, then disable autoconfig - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 100 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_Y_ROLLFF 1.1 - param set FW_L1_PERIOD 16 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 - - param set SYS_AUTOCONFIG 0 - param save -fi - -set VEHICLE_TYPE fw set MIXER FMU_AERT
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/3030_io_camflyer b/ROMFS/px4fmu_common/init.d/3030_io_camflyer index cbcc6189b..83c470234 100644 --- a/ROMFS/px4fmu_common/init.d/3030_io_camflyer +++ b/ROMFS/px4fmu_common/init.d/3030_io_camflyer @@ -1,40 +1,5 @@ #!nsh -echo "[init] PX4FMU v1, v2 with or without IO on Camflyer" +sh /etc/init.d/rc.fw_defaults -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set FW_AIRSPD_MIN 7 - param set FW_AIRSPD_TRIM 9 - param set FW_AIRSPD_MAX 14 - param set FW_L1_PERIOD 10 - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 20 - param set FW_P_LIM_MAX 30 - param set FW_P_LIM_MIN -20 - param set FW_P_P 30 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 2 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 60 - param set FW_R_RMAX 60 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 0.7 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5 - param set FW_T_SINK_MIN 2 - param set FW_T_TIME_CONST 9 - param set FW_Y_ROLLFF 2.0 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 -fi - -set VEHICLE_TYPE fw set MIXER FMU_Q diff --git a/ROMFS/px4fmu_common/init.d/3031_phantom b/ROMFS/px4fmu_common/init.d/3031_phantom index 4ebbe9c61..2e2434bb8 100644 --- a/ROMFS/px4fmu_common/init.d/3031_phantom +++ b/ROMFS/px4fmu_common/init.d/3031_phantom @@ -2,43 +2,7 @@ # # Phantom FPV Flying Wing # -# Maintainers: Simon Wilks <sjwilks@gmail.com> +# Simon Wilks <sjwilks@gmail.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set FW_AIRSPD_MIN 11.4 - param set FW_AIRSPD_TRIM 14 - param set FW_AIRSPD_MAX 22 - param set FW_L1_PERIOD 15 - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 45 - param set FW_P_LIM_MIN -45 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 2 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 15 - param set FW_R_P 80 - param set FW_R_RMAX 60 - param set FW_THR_CRUISE 0.8 - param set FW_THR_LND_MAX 0 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0.5 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 2.0 - param set FW_Y_ROLLFF 1.0 - param set RC_SCALE_ROLL 0.6 - param set RC_SCALE_PITCH 0.6 - param set TRIM_PITCH 0.1 -fi - -set VEHICLE_TYPE fw set MIXER FMU_Q diff --git a/ROMFS/px4fmu_common/init.d/3032_skywalker_x5 b/ROMFS/px4fmu_common/init.d/3032_skywalker_x5 index 143310af9..bf5a87068 100644 --- a/ROMFS/px4fmu_common/init.d/3032_skywalker_x5 +++ b/ROMFS/px4fmu_common/init.d/3032_skywalker_x5 @@ -2,42 +2,38 @@ # # Skywalker X5 Flying Wing # -# Maintainers: Thomas Gubler <thomasgubler@gmail.com>, Julian Oes <joes@student.ethz.ch> +# Thomas Gubler <thomasgubler@gmail.com>, Julian Oes <joes@student.ethz.ch> # +sh /etc/init.d/rc.fw_defaults + if [ $DO_AUTOCONFIG == yes ] then - # - # Default parameters for this platform - # - param set FW_AIRSPD_MIN 7 - param set FW_AIRSPD_TRIM 9 - param set FW_AIRSPD_MAX 14 - param set FW_L1_PERIOD 10 - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 20 - param set FW_P_LIM_MAX 30 - param set FW_P_LIM_MIN -20 - param set FW_P_P 30 + param set FW_AIRSPD_MIN 15 + param set FW_AIRSPD_TRIM 20 + param set FW_AIRSPD_MAX 40 + param set FW_ATT_TC 0.3 + param set FW_L1_DAMPING 0.74 + param set FW_L1_PERIOD 15 + param set FW_PR_FF 0.3 + param set FW_PR_I 0 + param set FW_PR_IMAX 0.2 + param set FW_PR_P 0.03 + param set FW_P_LIM_MAX 45 + param set FW_P_LIM_MIN -45 param set FW_P_RMAX_NEG 0 param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 2 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 60 - param set FW_R_RMAX 60 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 0.7 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5 - param set FW_T_SINK_MIN 2 - param set FW_T_TIME_CONST 9 - param set FW_Y_ROLLFF 2.0 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 + param set FW_P_ROLLFF 0 + param set FW_RR_FF 0.3 + param set FW_RR_I 0 + param set FW_RR_IMAX 0.2 + param set FW_RR_P 0.03 + param set FW_R_LIM 60 + param set FW_R_RMAX 0 + param set FW_T_HRATE_P 0.01 + param set FW_T_RLL2THR 15 + param set FW_T_SRATE_P 0.01 + param set FW_T_TIME_CONST 5 fi -set VEHICLE_TYPE fw set MIXER FMU_X5 diff --git a/ROMFS/px4fmu_common/init.d/3033_wingwing b/ROMFS/px4fmu_common/init.d/3033_wingwing index e53763278..2af3618d9 100644 --- a/ROMFS/px4fmu_common/init.d/3033_wingwing +++ b/ROMFS/px4fmu_common/init.d/3033_wingwing @@ -2,42 +2,9 @@ # # Wing Wing (aka Z-84) Flying Wing # -# Maintainers: Simon Wilks <sjwilks@gmail.com> +# Simon Wilks <sjwilks@gmail.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set FW_AIRSPD_MIN 7 - param set FW_AIRSPD_TRIM 9 - param set FW_AIRSPD_MAX 14 - param set FW_L1_PERIOD 10 - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 20 - param set FW_P_LIM_MAX 30 - param set FW_P_LIM_MIN -20 - param set FW_P_P 30 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 2 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 60 - param set FW_R_RMAX 60 - param set FW_THR_CRUISE 0.65 - param set FW_THR_MAX 0.7 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5 - param set FW_T_SINK_MIN 2 - param set FW_T_TIME_CONST 9 - param set FW_Y_ROLLFF 2.0 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 -fi +sh /etc/init.d/rc.fw_defaults -set VEHICLE_TYPE fw set MIXER FMU_Q diff --git a/ROMFS/px4fmu_common/init.d/3034_fx79 b/ROMFS/px4fmu_common/init.d/3034_fx79 index 8d179d1fd..f4bd18269 100644 --- a/ROMFS/px4fmu_common/init.d/3034_fx79 +++ b/ROMFS/px4fmu_common/init.d/3034_fx79 @@ -2,42 +2,9 @@ # # FX-79 Buffalo Flying Wing # -# Maintainers: Simon Wilks <sjwilks@gmail.com> +# Simon Wilks <sjwilks@gmail.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set FW_AIRSPD_MAX 20 - param set FW_AIRSPD_TRIM 12 - param set FW_AIRSPD_MIN 15 - param set FW_L1_PERIOD 12 - param set FW_P_D 0 - param set FW_P_I 0 - param set FW_P_IMAX 15 - param set FW_P_LIM_MAX 50 - param set FW_P_LIM_MIN -50 - param set FW_P_P 60 - param set FW_P_RMAX_NEG 0 - param set FW_P_RMAX_POS 0 - param set FW_P_ROLLFF 1.1 - param set FW_R_D 0 - param set FW_R_I 5 - param set FW_R_IMAX 20 - param set FW_R_P 80 - param set FW_R_RMAX 100 - param set FW_THR_CRUISE 0.75 - param set FW_THR_MAX 1 - param set FW_THR_MIN 0 - param set FW_T_SINK_MAX 5.0 - param set FW_T_SINK_MIN 4.0 - param set FW_T_TIME_CONST 9 - param set FW_Y_ROLLFF 1.1 - param set RC_SCALE_ROLL 1.0 - param set RC_SCALE_PITCH 1.0 -fi +sh /etc/init.d/rc.fw_defaults -set VEHICLE_TYPE fw set MIXER FMU_FX79 diff --git a/ROMFS/px4fmu_common/init.d/4001_quad_x b/ROMFS/px4fmu_common/init.d/4001_quad_x new file mode 100644 index 000000000..fa751f1e3 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/4001_quad_x @@ -0,0 +1,12 @@ +#!nsh +# +# Generic 10” Quad X geometry +# +# Lorenz Meier <lm@inf.ethz.ch> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_quad_x + +set PWM_OUTPUTS 1234
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/4008_ardrone b/ROMFS/px4fmu_common/init.d/4008_ardrone deleted file mode 100644 index f6f09ac22..000000000 --- a/ROMFS/px4fmu_common/init.d/4008_ardrone +++ /dev/null @@ -1,57 +0,0 @@ -#!nsh - -echo "[init] 08_ardrone: PX4FMU on PX4IOAR carrier board" - -# -# Load default params for this platform -# -if param compare SYS_AUTOCONFIG 1 -then - # Set all params here, then disable autoconfig - param set MC_ATTRATE_D 0 - param set MC_ATTRATE_I 0 - param set MC_ATTRATE_P 0.13 - param set MC_ATT_D 0 - param set MC_ATT_I 0.3 - param set MC_ATT_P 5 - param set MC_YAWPOS_D 0.1 - param set MC_YAWPOS_I 0.15 - param set MC_YAWPOS_P 1 - param set MC_YAWRATE_D 0 - param set MC_YAWRATE_I 0 - param set MC_YAWRATE_P 0.15 - - param set SYS_AUTOCONFIG 0 - param save -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 2 = quadrotor -# -param set MAV_TYPE 2 -param set BAT_V_SCALING 0.008381 - -# -# Start MAVLink -# -mavlink start -d /dev/ttyS0 -b 57600 -usleep 5000 - -# -# Configure PX4FMU for operation with PX4IOAR -# -fmu mode_gpio_serial - -# -# Fire up the AR.Drone interface. -# -ardrone_interface start -d /dev/ttyS1 - -# -# Start common for all multirotors apps -# -sh /etc/init.d/rc.multirotor - -# Exit, because /dev/ttyS0 is needed for MAVLink -exit diff --git a/ROMFS/px4fmu_common/init.d/4009_ardrone_flow b/ROMFS/px4fmu_common/init.d/4009_ardrone_flow deleted file mode 100644 index 2886bcb75..000000000 --- a/ROMFS/px4fmu_common/init.d/4009_ardrone_flow +++ /dev/null @@ -1,83 +0,0 @@ -#!nsh - -echo "[init] 09_ardrone_flow: PX4FMU on PX4IOAR carrier board with PX4FLOW" - -# -# Load default params for this platform -# -if param compare SYS_AUTOCONFIG 1 -then - # Set all params here, then disable autoconfig - param set MC_ATTRATE_D 0 - param set MC_ATTRATE_I 0 - param set MC_ATTRATE_P 0.13 - param set MC_ATT_D 0 - param set MC_ATT_I 0.3 - param set MC_ATT_P 5 - param set MC_YAWPOS_D 0.1 - param set MC_YAWPOS_I 0.15 - param set MC_YAWPOS_P 1 - param set MC_YAWRATE_D 0 - param set MC_YAWRATE_I 0 - param set MC_YAWRATE_P 0.15 - - param set SYS_AUTOCONFIG 0 - param save -fi - -# -# Force some key parameters to sane values -# MAV_TYPE 2 = quadrotor -# -param set MAV_TYPE 2 -param set BAT_V_SCALING 0.008381 - -# -# Start MAVLink and MAVLink Onboard (PX4FLOW Sensor) -# -mavlink start -d /dev/ttyS0 -b 57600 -mavlink_onboard start -d /dev/ttyS3 -b 115200 -usleep 5000 - -# -# Configure PX4FMU for operation with PX4IOAR -# -fmu mode_gpio_serial - -# -# Fire up the AR.Drone interface. -# -ardrone_interface start -d /dev/ttyS1 - -# -# Start the sensors. -# -sh /etc/init.d/rc.sensors - -# -# Start the attitude estimator -# -attitude_estimator_ekf start - -# -# Start the position estimator -# -flow_position_estimator start - -# -# Fire up the multi rotor attitude controller -# -multirotor_att_control start - -# -# Fire up the flow position controller -# -flow_position_control start - -# -# Fire up the flow speed controller -# -flow_speed_control start - -# Exit, because /dev/ttyS0 is needed for MAVLink -exit diff --git a/ROMFS/px4fmu_common/init.d/4010_dji_f330 b/ROMFS/px4fmu_common/init.d/4010_dji_f330 index ab1db94d0..232af57b4 100644 --- a/ROMFS/px4fmu_common/init.d/4010_dji_f330 +++ b/ROMFS/px4fmu_common/init.d/4010_dji_f330 @@ -2,50 +2,9 @@ # # DJI Flame Wheel F330 Quadcopter # -# Maintainers: Anton Babushkin <anton.babushkin@me.com> +# Anton Babushkin <anton.babushkin@me.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.8 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.2 - param set MC_YAWRATE_I 0.05 - param set MC_YAWRATE_D 0.0 - - param set MPC_TILT_MAX 0.5 - param set MPC_THR_MAX 0.8 - param set MPC_THR_MIN 0.2 - param set MPC_XY_D 0 - param set MPC_XY_P 0.5 - param set MPC_XY_VEL_D 0 - param set MPC_XY_VEL_I 0 - param set MPC_XY_VEL_MAX 3 - param set MPC_XY_VEL_P 0.2 - param set MPC_Z_D 0 - param set MPC_Z_P 1 - param set MPC_Z_VEL_D 0 - param set MPC_Z_VEL_I 0.1 - param set MPC_Z_VEL_MAX 2 - param set MPC_Z_VEL_P 0.20 -fi +sh /etc/init.d/4001_quad_x -set VEHICLE_TYPE mc -set MIXER FMU_quad_x - -set PWM_OUTPUTS 1234 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 +set PWM_MIN 1175
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/4011_dji_f450 b/ROMFS/px4fmu_common/init.d/4011_dji_f450 index 299771c1d..259636acc 100644 --- a/ROMFS/px4fmu_common/init.d/4011_dji_f450 +++ b/ROMFS/px4fmu_common/init.d/4011_dji_f450 @@ -2,36 +2,9 @@ # # DJI Flame Wheel F450 Quadcopter # -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> +# Lorenz Meier <lm@inf.ethz.ch> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi +sh /etc/init.d/4001_quad_x -set VEHICLE_TYPE mc -set MIXER FMU_quad_x - -set PWM_OUTPUTS 1234 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 +set PWM_MIN 1175
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/4012_hk_x550 b/ROMFS/px4fmu_common/init.d/4012_hk_x550 index 7e020cf59..a5c4a8690 100644 --- a/ROMFS/px4fmu_common/init.d/4012_hk_x550 +++ b/ROMFS/px4fmu_common/init.d/4012_hk_x550 @@ -2,32 +2,7 @@ # # HobbyKing X550 Quadcopter # -# Maintainers: Todd Stellanova <tstellanova@gmail.com> +# Todd Stellanova <tstellanova@gmail.com> # -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 5.5 - param set MC_ATT_I 0 - param set MC_ATT_D 0 - param set MC_ATTRATE_P 0.14 - param set MC_ATTRATE_I 0 - param set MC_ATTRATE_D 0.006 - param set MC_YAWPOS_P 0.6 - param set MC_YAWPOS_I 0 - param set MC_YAWPOS_D 0 - param set MC_YAWRATE_P 0.08 - param set MC_YAWRATE_I 0 - param set MC_YAWRATE_D 0 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_quad_x - -set PWM_OUTPUTS 1234 -set PWM_RATE 400 +sh /etc/init.d/4001_quad_x diff --git a/ROMFS/px4fmu_common/init.d/5001_quad_+ b/ROMFS/px4fmu_common/init.d/5001_quad_+ new file mode 100644 index 000000000..2f5ab44d7 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/5001_quad_+ @@ -0,0 +1,12 @@ +#!nsh +# +# Generic 10” Quad + geometry +# +# Anton Babushkin <anton.babushkin@me.com> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_quad_+ + +set PWM_OUTPUTS 1234
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/5001_quad_+_pwm b/ROMFS/px4fmu_common/init.d/5001_quad_+_pwm deleted file mode 100644 index 2e5f6ca4f..000000000 --- a/ROMFS/px4fmu_common/init.d/5001_quad_+_pwm +++ /dev/null @@ -1,37 +0,0 @@ -#!nsh -# -# Generic 10” Quad + geometry -# -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> -# - -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_quad_+ - -set PWM_OUTPUTS 1234 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 diff --git a/ROMFS/px4fmu_common/init.d/6001_hexa_x b/ROMFS/px4fmu_common/init.d/6001_hexa_x new file mode 100644 index 000000000..73ef12569 --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/6001_hexa_x @@ -0,0 +1,14 @@ +#!nsh +# +# Generic 10” Hexa X geometry +# +# Anton Babushkin <anton.babushkin@me.com> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_hexa_x + +# We only can run one channel group with one rate, +# so all 8 at 400 Hz +set PWM_OUTPUTS 12345678
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/6001_hexa_x_pwm b/ROMFS/px4fmu_common/init.d/6001_hexa_x_pwm deleted file mode 100644 index 447796709..000000000 --- a/ROMFS/px4fmu_common/init.d/6001_hexa_x_pwm +++ /dev/null @@ -1,37 +0,0 @@ -#!nsh -# -# Generic 10” Hexa X geometry -# -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> -# - -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_hexa_x - -set PWM_OUTPUTS 12345678 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 diff --git a/ROMFS/px4fmu_common/init.d/7001_hexa_+ b/ROMFS/px4fmu_common/init.d/7001_hexa_+ new file mode 100644 index 000000000..ef4b6297d --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/7001_hexa_+ @@ -0,0 +1,14 @@ +#!nsh +# +# Generic 10” Hexa + geometry +# +# Anton Babushkin <anton.babushkin@me.com> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_hexa_+ + +# We only can run one channel group with one rate, +# so all 8 at 400 Hz +set PWM_OUTPUTS 12345678
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/7001_hexa_+_pwm b/ROMFS/px4fmu_common/init.d/7001_hexa_+_pwm deleted file mode 100644 index c4e9560d1..000000000 --- a/ROMFS/px4fmu_common/init.d/7001_hexa_+_pwm +++ /dev/null @@ -1,37 +0,0 @@ -#!nsh -# -# Generic 10” Hexa + geometry -# -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> -# - -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_hexa_+ - -set PWM_OUTPUTS 12345678 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 diff --git a/ROMFS/px4fmu_common/init.d/8001_octo_x b/ROMFS/px4fmu_common/init.d/8001_octo_x new file mode 100644 index 000000000..bb87f89fe --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/8001_octo_x @@ -0,0 +1,12 @@ +#!nsh +# +# Generic 10” Octo X geometry +# +# Anton Babushkin <anton.babushkin@me.com> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_octo_x + +set PWM_OUTPUTS 12345678
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/8001_octo_x_pwm b/ROMFS/px4fmu_common/init.d/8001_octo_x_pwm deleted file mode 100644 index ea56195d4..000000000 --- a/ROMFS/px4fmu_common/init.d/8001_octo_x_pwm +++ /dev/null @@ -1,37 +0,0 @@ -#!nsh -# -# Generic 10” Octo X geometry -# -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> -# - -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_octo_x - -set PWM_OUTPUTS 12345678 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 diff --git a/ROMFS/px4fmu_common/init.d/9001_octo_+ b/ROMFS/px4fmu_common/init.d/9001_octo_+ new file mode 100644 index 000000000..81132fd3e --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/9001_octo_+ @@ -0,0 +1,12 @@ +#!nsh +# +# Generic 10” Octo + geometry +# +# Anton Babushkin <anton.babushkin@me.com> +# + +sh /etc/init.d/rc.mc_defaults + +set MIXER FMU_octo_+ + +set PWM_OUTPUTS 12345678
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/9001_octo_+_pwm b/ROMFS/px4fmu_common/init.d/9001_octo_+_pwm deleted file mode 100644 index f7693875c..000000000 --- a/ROMFS/px4fmu_common/init.d/9001_octo_+_pwm +++ /dev/null @@ -1,37 +0,0 @@ -#!nsh -# -# Generic 10” Octo + geometry -# -# Maintainers: Lorenz Meier <lm@inf.ethz.ch> -# - -if [ $DO_AUTOCONFIG == yes ] -then - # - # Default parameters for this platform - # - param set MC_ATT_P 7.0 - param set MC_ATT_I 0.0 - param set MC_ATT_D 0.0 - param set MC_ATTRATE_P 0.12 - param set MC_ATTRATE_I 0.0 - param set MC_ATTRATE_D 0.004 - param set MC_YAWPOS_P 2.0 - param set MC_YAWPOS_I 0.0 - param set MC_YAWPOS_D 0.0 - param set MC_YAWRATE_P 0.3 - param set MC_YAWRATE_I 0.2 - param set MC_YAWRATE_D 0.005 - - # TODO add default MPC parameters -fi - -set VEHICLE_TYPE mc -set MIXER FMU_octo_+ - -set PWM_OUTPUTS 12345678 -set PWM_RATE 400 -# DJI ESC range -set PWM_DISARMED 900 -set PWM_MIN 1200 -set PWM_MAX 1900 diff --git a/ROMFS/px4fmu_common/init.d/rc.autostart b/ROMFS/px4fmu_common/init.d/rc.autostart index 38b1cb57e..48c26aacd 100644 --- a/ROMFS/px4fmu_common/init.d/rc.autostart +++ b/ROMFS/px4fmu_common/init.d/rc.autostart @@ -31,11 +31,6 @@ then sh /etc/init.d/1001_rc_quad_x.hil fi -if param compare SYS_AUTOSTART 1002 -then - sh /etc/init.d/1002_rc_fw_state.hil -fi - if param compare SYS_AUTOSTART 1003 then sh /etc/init.d/1003_rc_quad_+.hil @@ -46,6 +41,11 @@ then sh /etc/init.d/1004_rc_fw_Rascal110.hil fi +if param compare SYS_AUTOSTART 1005 +then + sh /etc/init.d/1005_rc_fw_Malolo1.hil +fi + # # Standard plane # @@ -101,14 +101,9 @@ fi # Quad X # -if param compare SYS_AUTOSTART 4008 8 -then - #sh /etc/init.d/4008_ardrone -fi - -if param compare SYS_AUTOSTART 4009 9 +if param compare SYS_AUTOSTART 4001 then - #sh /etc/init.d/4009_ardrone_flow + sh /etc/init.d/4001_quad_x fi if param compare SYS_AUTOSTART 4010 10 @@ -132,7 +127,7 @@ fi if param compare SYS_AUTOSTART 5001 then - sh /etc/init.d/5001_quad_+_pwm + sh /etc/init.d/5001_quad_+ fi # @@ -141,7 +136,7 @@ fi if param compare SYS_AUTOSTART 6001 then - sh /etc/init.d/6001_hexa_x_pwm + sh /etc/init.d/6001_hexa_x fi # @@ -150,7 +145,7 @@ fi if param compare SYS_AUTOSTART 7001 then - sh /etc/init.d/7001_hexa_+_pwm + sh /etc/init.d/7001_hexa_+ fi # @@ -159,7 +154,7 @@ fi if param compare SYS_AUTOSTART 8001 then - sh /etc/init.d/8001_octo_x_pwm + sh /etc/init.d/8001_octo_x fi # @@ -168,7 +163,7 @@ fi if param compare SYS_AUTOSTART 9001 then - sh /etc/init.d/9001_octo_+_pwm + sh /etc/init.d/9001_octo_+ fi # diff --git a/ROMFS/px4fmu_common/init.d/rc.fw_apps b/ROMFS/px4fmu_common/init.d/rc.fw_apps index d354fb06f..72327c554 100644 --- a/ROMFS/px4fmu_common/init.d/rc.fw_apps +++ b/ROMFS/px4fmu_common/init.d/rc.fw_apps @@ -3,17 +3,6 @@ # Standard apps for fixed wing # -# -# Start the attitude and position estimator -# att_pos_estimator_ekf start - -# -# Start attitude controller -# fw_att_control start - -# -# Start the position controller -# fw_pos_control_l1 start diff --git a/ROMFS/px4fmu_common/init.d/rc.fw_defaults b/ROMFS/px4fmu_common/init.d/rc.fw_defaults new file mode 100644 index 000000000..3e340699f --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.fw_defaults @@ -0,0 +1,13 @@ +#!nsh + +set VEHICLE_TYPE fw + +if [ $DO_AUTOCONFIG == yes ] +then +# +# Default parameters for FW +# + param set NAV_LAND_ALT 90 + param set NAV_RTL_ALT 100 + param set NAV_RTL_LAND_T -1 +fi
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/rc.io b/ROMFS/px4fmu_common/init.d/rc.io index c9d964f8e..6e8fdbc0f 100644 --- a/ROMFS/px4fmu_common/init.d/rc.io +++ b/ROMFS/px4fmu_common/init.d/rc.io @@ -4,7 +4,6 @@ # # Allow PX4IO to recover from midair restarts. -# this is very unlikely, but quite safe and robust. # px4io recovery diff --git a/ROMFS/px4fmu_common/init.d/rc.logging b/ROMFS/px4fmu_common/init.d/rc.logging index ac620844c..c5aef8273 100644 --- a/ROMFS/px4fmu_common/init.d/rc.logging +++ b/ROMFS/px4fmu_common/init.d/rc.logging @@ -7,8 +7,10 @@ if [ -d /fs/microsd ] then if hw_ver compare PX4FMU_V1 then - sdlog2 start -r 50 -a -b 16 -t + echo "Start sdlog2 at 50Hz" + sdlog2 start -r 50 -a -b 8 -t else + echo "Start sdlog2 at 200Hz" sdlog2 start -r 200 -a -b 16 -t fi fi diff --git a/ROMFS/px4fmu_common/init.d/rc.mc_apps b/ROMFS/px4fmu_common/init.d/rc.mc_apps index 8b51d57e5..ed3939757 100644 --- a/ROMFS/px4fmu_common/init.d/rc.mc_apps +++ b/ROMFS/px4fmu_common/init.d/rc.mc_apps @@ -1,24 +1,11 @@ #!nsh # -# Standard apps for multirotors +# Standard apps for multirotors: +# att & pos estimator, att & pos control. # -# -# Start the attitude estimator -# attitude_estimator_ekf start - -# -# Start position estimator -# position_estimator_inav start -# -# Start attitude control -# -multirotor_att_control start - -# -# Start position control -# -multirotor_pos_control start +mc_att_control start +mc_pos_control start diff --git a/ROMFS/px4fmu_common/init.d/rc.mc_defaults b/ROMFS/px4fmu_common/init.d/rc.mc_defaults new file mode 100644 index 000000000..52584677b --- /dev/null +++ b/ROMFS/px4fmu_common/init.d/rc.mc_defaults @@ -0,0 +1,45 @@ +#!nsh + +set VEHICLE_TYPE mc + +if [ $DO_AUTOCONFIG == yes ] +then + # + # Default parameters for MC + # + param set MC_ROLL_P 7.0 + param set MC_ROLLRATE_P 0.12 + param set MC_ROLLRATE_I 0.0 + param set MC_ROLLRATE_D 0.004 + param set MC_PITCH_P 7.0 + param set MC_PITCHRATE_P 0.12 + param set MC_PITCHRATE_I 0.0 + param set MC_PITCHRATE_D 0.004 + param set MC_YAW_P 2.0 + param set MC_YAWRATE_P 0.3 + param set MC_YAWRATE_I 0.2 + param set MC_YAWRATE_D 0.005 + + param set MPC_THR_MAX 1.0 + param set MPC_THR_MIN 0.1 + param set MPC_XY_P 1.0 + param set MPC_XY_VEL_P 0.1 + param set MPC_XY_VEL_I 0.02 + param set MPC_XY_VEL_D 0.01 + param set MPC_XY_VEL_MAX 5 + param set MPC_XY_FF 0.5 + param set MPC_Z_P 1.0 + param set MPC_Z_VEL_P 0.1 + param set MPC_Z_VEL_I 0.02 + param set MPC_Z_VEL_D 0.0 + param set MPC_Z_VEL_MAX 3 + param set MPC_Z_FF 0.5 + param set MPC_TILT_MAX 1.0 + param set MPC_LAND_SPEED 1.0 + param set MPC_LAND_TILT 0.3 +fi + +set PWM_RATE 400 +set PWM_DISARMED 900 +set PWM_MIN 1075 +set PWM_MAX 2000
\ No newline at end of file diff --git a/ROMFS/px4fmu_common/init.d/rc.sensors b/ROMFS/px4fmu_common/init.d/rc.sensors index badbf92c3..235be2431 100644 --- a/ROMFS/px4fmu_common/init.d/rc.sensors +++ b/ROMFS/px4fmu_common/init.d/rc.sensors @@ -3,10 +3,6 @@ # Standard startup script for PX4FMU onboard sensor drivers. # -# -# Start sensor drivers here. -# - ms5611 start adc start diff --git a/ROMFS/px4fmu_common/init.d/rcS b/ROMFS/px4fmu_common/init.d/rcS index 50ac9759a..588a44a01 100644 --- a/ROMFS/px4fmu_common/init.d/rcS +++ b/ROMFS/px4fmu_common/init.d/rcS @@ -3,8 +3,7 @@ # PX4FMU startup script. # -# Default to auto-start mode. An init script on the microSD card -# can change this to prevent automatic startup of the flight script. +# Default to auto-start mode. # set MODE autostart @@ -326,7 +325,7 @@ then if [ $OUTPUT_MODE == hil ] then echo "[init] Use HIL as primary output" - if hil mode_pwm + if hil mode_port2_pwm8 then echo "[init] HIL output started" else @@ -404,6 +403,16 @@ then fi # + # Start the datamanager + # + dataman start + + # + # Start the navigator + # + navigator start + + # # Sensors, Logging, GPS # echo "[init] Start sensors" @@ -455,18 +464,21 @@ then if [ $MIXER == none ] then - # Set default mixer for multicopter if not defined - set MIXER quad_x + echo "Default mixer for multicopter not defined" fi if [ $MAV_TYPE == none ] then - # Use MAV_TYPE = 2 (quadcopter) if not defined - set MAV_TYPE 2 - # Use mixer to detect vehicle type - if [ $MIXER == FMU_hex_x -o $MIXER == FMU_hex_+ ] + if [ $MIXER == FMU_quad_x -o $MIXER == FMU_quad_+ ] then + set MAV_TYPE 2 + fi + if [ $MIXER == FMU_quad_w ] + then + set MAV_TYPE 2 + fi + if [ $MIXER == FMU_hexa_x -o $MIXER == FMU_hexa_+ ] set MAV_TYPE 13 fi if [ $MIXER == hexa_cox ] @@ -482,8 +494,14 @@ then set MAV_TYPE 14 fi fi - - param set MAV_TYPE $MAV_TYPE + + # Still no MAV_TYPE found + if [ $MAV_TYPE == none ] + then + echo "Unknown MAV_TYPE" + else + param set MAV_TYPE $MAV_TYPE + fi # Load mixer and configure outputs sh /etc/init.d/rc.interface @@ -497,10 +515,8 @@ then # if [ $VEHICLE_TYPE == none ] then - echo "[init] Vehicle type: GENERIC" + echo "[init] Vehicle type: No autostart ID found" - # Load mixer and configure outputs - sh /etc/init.d/rc.interface fi # Start any custom addons diff --git a/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix b/ROMFS/px4fmu_common/mixers/FMU_hexa_+.mix index e608b459f..e608b459f 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_hex_+.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_hexa_+.mix diff --git a/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix b/ROMFS/px4fmu_common/mixers/FMU_hexa_x.mix index 16e6e22f9..16e6e22f9 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_hex_x.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_hexa_x.mix diff --git a/ROMFS/px4fmu_common/mixers/FMU_octo_+.mix b/ROMFS/px4fmu_common/mixers/FMU_octo_+.mix index 2cb70e814..397e22086 100644 --- a/ROMFS/px4fmu_common/mixers/FMU_octo_+.mix +++ b/ROMFS/px4fmu_common/mixers/FMU_octo_+.mix @@ -1,7 +1,3 @@ -Multirotor mixer for PX4FMU -=========================== - -This file defines a single mixer for a octocopter in the + configuration. All controls -are mixed 100%. +# Octo + R: 8+ 10000 10000 10000 0 |