diff options
Diffstat (limited to 'nuttx/arch/arm/Kconfig')
| -rw-r--r-- | nuttx/arch/arm/Kconfig | 32 |
1 files changed, 26 insertions, 6 deletions
diff --git a/nuttx/arch/arm/Kconfig b/nuttx/arch/arm/Kconfig index 2a7ea10b5..4fce8efbf 100644 --- a/nuttx/arch/arm/Kconfig +++ b/nuttx/arch/arm/Kconfig @@ -4,6 +4,8 @@ # if ARCH_ARM +comment "ARM Options" + choice prompt "ARM chip selection" default ARCH_CHIP_STM32 @@ -44,6 +46,7 @@ config ARCH_CHIP_KINETIS bool "Freescale Kinetis" select ARCH_CORTEXM4 select ARCH_HAVE_MPU + select ARCH_IRQPRIO ---help--- Freescale Kinetis Architectures (ARM Cortex-M4) @@ -51,6 +54,7 @@ config ARCH_CHIP_LM3S bool "TI Stellaris" select ARCH_CORTEXM3 select ARCH_HAVE_MPU + select ARCH_IRQPRIO ---help--- TI Stellaris LMS3 architecutres (ARM Cortex-M3) @@ -58,6 +62,7 @@ config ARCH_CHIP_LPC17XX bool "NXP LPC17xx" select ARCH_CORTEXM3 select ARCH_HAVE_MPU + select ARCH_IRQPRIO ---help--- NXP LPC17xx architectures (ARM Cortex-M3) @@ -89,6 +94,7 @@ config ARCH_CHIP_LPC43XX select ARCH_HAVE_CMNVECTOR select ARMV7M_CMNVECTOR select ARCH_HAVE_MPU + select ARCH_IRQPRIO ---help--- NPX LPC43XX architectures (ARM Cortex-M4). @@ -96,6 +102,7 @@ config ARCH_CHIP_SAM3U bool "Atmel AT91SAM3U" select ARCH_CORTEXM3 select ARCH_HAVE_MPU + select ARCH_IRQPRIO ---help--- Atmel AT91SAM3U architectures (ARM Cortex-M3) @@ -104,6 +111,7 @@ config ARCH_CHIP_STM32 select ARCH_HAVE_CMNVECTOR select ARCH_HAVE_MPU select ARCH_HAVE_I2CRESET + select ARCH_IRQPRIO ---help--- STMicro STM32 architectures (ARM Cortex-M3/4). @@ -153,6 +161,9 @@ config ARCH_CHIP default "stm32" if ARCH_CHIP_STM32 default "str71x" if ARCH_CHIP_STR71X +config ARCH_HAVE_CMNVECTOR + bool + config ARMV7M_CMNVECTOR bool "Use common ARMv7-M vectors" default n @@ -217,12 +228,6 @@ config PAGING If set =y in your configation file, this setting will enable the on-demand paging feature as described in http://www.nuttx.org/NuttXDemandPaging.html. -config ARCH_IRQPRIO - bool "Interrupt priority" - default y if ARCH_CORTEXM3 || ARCH_CORTEXM4 - ---help--- - Select if your board supports interrupt prioritization. - config BOARD_LOOPSPERMSEC int "Delay loops per millisecond" default 5000 @@ -239,6 +244,21 @@ config ARCH_CALIBRATION watch to measure the 100 second delay then adjust BOARD_LOOPSPERMSEC until the delay actually is 100 seconds. +config DEBUG_HARDFAULT + bool "Verbose Hard-Fault Debug" + default n + depends on DEBUG && (ARCH_CORTEXM3 || ARCH_CORTEXM4) + ---help--- + Enables verbose debug output when a hard fault is occurs. This verbose + output is sometimes helpful when debugging difficult hard fault problems, + but may be more than you typcially want to see. + +if ARCH_CORTEXM3 || ARCH_CORTEXM4 +source arch/arm/src/armv7-m/Kconfig +endif +if ARCH_ARM7TDMI || ARCH_ARM926EJS +source arch/arm/src/arm/Kconfig +endif if ARCH_CHIP_C5471 source arch/arm/src/c5471/Kconfig endif |