diff options
Diffstat (limited to 'nuttx/configs')
-rw-r--r-- | nuttx/configs/px4fmuv2/Kconfig | 7 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/common/Make.defs | 184 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/common/ld.script | 150 | ||||
-rwxr-xr-x | nuttx/configs/px4fmuv2/include/board.h | 351 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/include/nsh_romfsimg.h | 42 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/nsh/Make.defs | 3 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/nsh/appconfig | 143 | ||||
-rwxr-xr-x | nuttx/configs/px4fmuv2/nsh/defconfig | 1050 | ||||
-rwxr-xr-x | nuttx/configs/px4fmuv2/nsh/setenv.sh | 67 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/src/Makefile | 84 | ||||
-rw-r--r-- | nuttx/configs/px4fmuv2/src/empty.c | 4 |
11 files changed, 2085 insertions, 0 deletions
diff --git a/nuttx/configs/px4fmuv2/Kconfig b/nuttx/configs/px4fmuv2/Kconfig new file mode 100644 index 000000000..a10a02ba4 --- /dev/null +++ b/nuttx/configs/px4fmuv2/Kconfig @@ -0,0 +1,7 @@ +# +# For a description of the syntax of this configuration file, +# see misc/tools/kconfig-language.txt. +# + +if ARCH_BOARD_PX4FMUV2 +endif diff --git a/nuttx/configs/px4fmuv2/common/Make.defs b/nuttx/configs/px4fmuv2/common/Make.defs new file mode 100644 index 000000000..be387dce1 --- /dev/null +++ b/nuttx/configs/px4fmuv2/common/Make.defs @@ -0,0 +1,184 @@ +############################################################################ +# configs/px4fmu/common/Make.defs +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +# +# Generic Make.defs for the PX4FMUV2 +# Do not specify/use this file directly - it is included by config-specific +# Make.defs in the per-config directories. +# + +include ${TOPDIR}/tools/Config.mk + +# +# We only support building with the ARM bare-metal toolchain from +# https://launchpad.net/gcc-arm-embedded on Windows, Linux or Mac OS. +# +CONFIG_ARMV7M_TOOLCHAIN := GNU_EABI + +include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs + +CC = $(CROSSDEV)gcc +CXX = $(CROSSDEV)g++ +CPP = $(CROSSDEV)gcc -E +LD = $(CROSSDEV)ld +AR = $(CROSSDEV)ar rcs +NM = $(CROSSDEV)nm +OBJCOPY = $(CROSSDEV)objcopy +OBJDUMP = $(CROSSDEV)objdump + +MAXOPTIMIZATION = -O3 +ARCHCPUFLAGS = -mcpu=cortex-m4 \ + -mthumb \ + -march=armv7e-m \ + -mfpu=fpv4-sp-d16 \ + -mfloat-abi=hard + + +# enable precise stack overflow tracking +INSTRUMENTATIONDEFINES = -finstrument-functions \ + -ffixed-r10 + +# pull in *just* libm from the toolchain ... this is grody +LIBM = "${shell $(CC) $(ARCHCPUFLAGS) -print-file-name=libm.a}" +EXTRA_LIBS += $(LIBM) + +# use our linker script +LDSCRIPT = ld.script + +ifeq ($(WINTOOL),y) + # Windows-native toolchains + DIRLINK = $(TOPDIR)/tools/copydir.sh + DIRUNLINK = $(TOPDIR)/tools/unlink.sh + MKDEP = $(TOPDIR)/tools/mknulldeps.sh + ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" + ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}" + ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/common/$(LDSCRIPT)}" +else + ifeq ($(PX4_WINTOOL),y) + # Windows-native toolchains (MSYS) + DIRLINK = $(TOPDIR)/tools/copydir.sh + DIRUNLINK = $(TOPDIR)/tools/unlink.sh + MKDEP = $(TOPDIR)/tools/mknulldeps.sh + ARCHINCLUDES = -I. -isystem $(TOPDIR)/include + ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx + ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/common/$(LDSCRIPT) + else + # Linux/Cygwin-native toolchain + MKDEP = $(TOPDIR)/tools/mkdeps.sh + ARCHINCLUDES = -I. -isystem $(TOPDIR)/include + ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx + ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/common/$(LDSCRIPT) + endif +endif + +# tool versions +ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'} +ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1} + +# optimisation flags +ARCHOPTIMIZATION = $(MAXOPTIMIZATION) \ + -fno-strict-aliasing \ + -fno-strength-reduce \ + -fomit-frame-pointer \ + -funsafe-math-optimizations \ + -fno-builtin-printf \ + -ffunction-sections \ + -fdata-sections + +ifeq ("${CONFIG_DEBUG_SYMBOLS}","y") +ARCHOPTIMIZATION += -g +endif + +ARCHCFLAGS = -std=gnu99 +ARCHCXXFLAGS = -fno-exceptions -fno-rtti -std=gnu++0x +ARCHWARNINGS = -Wall \ + -Wextra \ + -Wdouble-promotion \ + -Wshadow \ + -Wfloat-equal \ + -Wframe-larger-than=1024 \ + -Wpointer-arith \ + -Wlogical-op \ + -Wmissing-declarations \ + -Wpacked \ + -Wno-unused-parameter +# -Wcast-qual - generates spurious noreturn attribute warnings, try again later +# -Wconversion - would be nice, but too many "risky-but-safe" conversions in the code +# -Wcast-align - would help catch bad casts in some cases, but generates too many false positives + +ARCHCWARNINGS = $(ARCHWARNINGS) \ + -Wbad-function-cast \ + -Wstrict-prototypes \ + -Wold-style-declaration \ + -Wmissing-parameter-type \ + -Wmissing-prototypes \ + -Wnested-externs \ + -Wunsuffixed-float-constants +ARCHWARNINGSXX = $(ARCHWARNINGS) \ + -Wno-psabi +ARCHDEFINES = +ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10 + +# this seems to be the only way to add linker flags +EXTRA_LIBS += --warn-common \ + --gc-sections + +CFLAGS = $(ARCHCFLAGS) $(ARCHCWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(INSTRUMENTATIONDEFINES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe -fno-common +CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS) +CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(INSTRUMENTATIONDEFINES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe +CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS) +CPPFLAGS = $(ARCHINCLUDES) $(INSTRUMENTATIONDEFINES) $(ARCHDEFINES) $(EXTRADEFINES) +AFLAGS = $(CFLAGS) -D__ASSEMBLY__ + +NXFLATLDFLAGS1 = -r -d -warn-common +NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat.ld -no-check-sections +LDNXFLATFLAGS = -e main -s 2048 + +OBJEXT = .o +LIBEXT = .a +EXEEXT = + + +# produce partially-linked $1 from files in $2 +define PRELINK + @echo "PRELINK: $1" + $(Q) $(LD) -Ur -o $1 $2 && $(OBJCOPY) --localize-hidden $1 +endef + +HOSTCC = gcc +HOSTINCLUDES = -I. +HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe +HOSTLDFLAGS = + diff --git a/nuttx/configs/px4fmuv2/common/ld.script b/nuttx/configs/px4fmuv2/common/ld.script new file mode 100644 index 000000000..1be39fb87 --- /dev/null +++ b/nuttx/configs/px4fmuv2/common/ld.script @@ -0,0 +1,150 @@ +/**************************************************************************** + * configs/px4fmu/common/ld.script + * + * Copyright (C) 2011 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <gnutt@nuttx.org> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The STM32F427 has 2048Kb of FLASH beginning at address 0x0800:0000 and + * 256Kb of SRAM. SRAM is split up into three blocks: + * + * 1) 112Kb of SRAM beginning at address 0x2000:0000 + * 2) 16Kb of SRAM beginning at address 0x2001:c000 + * 3) 64Kb of SRAM beginning at address 0x2002:0000 + * 4) 64Kb of TCM SRAM beginning at address 0x1000:0000 + * + * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000 + * where the code expects to begin execution by jumping to the entry point in + * the 0x0800:0000 address range. + * + * The first 0x4000 of flash is reserved for the bootloader. + */ + +MEMORY +{ + flash (rx) : ORIGIN = 0x08004000, LENGTH = 2032K + sram (rwx) : ORIGIN = 0x20000000, LENGTH = 192K + ccsram (rwx) : ORIGIN = 0x10000000, LENGTH = 64K +} + +OUTPUT_ARCH(arm) + +ENTRY(__start) /* treat __start as the anchor for dead code stripping */ +EXTERN(_vectors) /* force the vectors to be included in the output */ + +/* + * Ensure that abort() is present in the final object. The exception handling + * code pulled in by libgcc.a requires it (and that code cannot be easily avoided). + */ +EXTERN(abort) + +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + + /* + * This is a hack to make the newlib libm __errno() call + * use the NuttX get_errno_ptr() function. + */ + __errno = get_errno_ptr; + } > flash + + /* + * Init functions (static constructors and the like) + */ + .init_section : { + _sinit = ABSOLUTE(.); + KEEP(*(.init_array .init_array.*)) + _einit = ABSOLUTE(.); + } > flash + + /* + * Construction data for parameters. + */ + __param ALIGN(4): { + __param_start = ABSOLUTE(.); + KEEP(*(__param*)) + __param_end = ABSOLUTE(.); + } > flash + + .ARM.extab : { + *(.ARM.extab*) + } > flash + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } > flash + __exidx_end = ABSOLUTE(.); + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/nuttx/configs/px4fmuv2/include/board.h b/nuttx/configs/px4fmuv2/include/board.h new file mode 100755 index 000000000..286dedab0 --- /dev/null +++ b/nuttx/configs/px4fmuv2/include/board.h @@ -0,0 +1,351 @@ +/************************************************************************************ + * configs/px4fmu/include/board.h + * include/arch/board/board.h + * + * Copyright (C) 2009 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt <gnutt@nuttx.org> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __ARCH_BOARD_BOARD_H +#define __ARCH_BOARD_BOARD_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include <nuttx/config.h> +#ifndef __ASSEMBLY__ +# include <stdint.h> +#endif + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/* Clocking *************************************************************************/ +/* The PX4FMUV2 uses a 24MHz crystal connected to the HSE. + * + * This is the "standard" configuration as set up by arch/arm/src/stm32f40xx_rcc.c: + * System Clock source : PLL (HSE) + * SYSCLK(Hz) : 168000000 Determined by PLL configuration + * HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE) + * AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE) + * APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1) + * APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2) + * HSE Frequency(Hz) : 24000000 (STM32_BOARD_XTAL) + * PLLM : 24 (STM32_PLLCFG_PLLM) + * PLLN : 336 (STM32_PLLCFG_PLLN) + * PLLP : 2 (STM32_PLLCFG_PLLP) + * PLLQ : 7 (STM32_PLLCFG_PPQ) + * Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK + * Flash Latency(WS) : 5 + * Prefetch Buffer : OFF + * Instruction cache : ON + * Data cache : ON + * Require 48MHz for USB OTG FS, : Enabled + * SDIO and RNG clock + */ + +/* HSI - 16 MHz RC factory-trimmed + * LSI - 32 KHz RC + * HSE - On-board crystal frequency is 24MHz + * LSE - not installed + */ + +#define STM32_BOARD_XTAL 24000000ul + +#define STM32_HSI_FREQUENCY 16000000ul +#define STM32_LSI_FREQUENCY 32000 +#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL +//#define STM32_LSE_FREQUENCY 32768 + +/* Main PLL Configuration. + * + * PLL source is HSE + * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN + * = (25,000,000 / 25) * 336 + * = 336,000,000 + * SYSCLK = PLL_VCO / PLLP + * = 336,000,000 / 2 = 168,000,000 + * USB OTG FS, SDIO and RNG Clock + * = PLL_VCO / PLLQ + * = 48,000,000 + */ + +#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(24) +#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) +#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 +#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) + +#define STM32_SYSCLK_FREQUENCY 168000000ul + +/* AHB clock (HCLK) is SYSCLK (168MHz) */ + +#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ +#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY +#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ + +/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ + +#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ +#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) + +/* Timers driven from APB1 will be twice PCLK1 */ + +#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) + +/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ + +#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ +#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* Timers driven from APB2 will be twice PCLK2 */ + +#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK1_FREQUENCY) + +/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx + * otherwise frequency is 2xAPBx. + * Note: TIM1,8 are on APB2, others on APB1 + */ + +#define STM32_TIM18_FREQUENCY (2*STM32_PCLK2_FREQUENCY) +#define STM32_TIM27_FREQUENCY (2*STM32_PCLK1_FREQUENCY) + +/* SDIO dividers. Note that slower clocking is required when DMA is disabled + * in order to avoid RX overrun/TX underrun errors due to delayed responses + * to service FIFOs in interrupt driven mode. These values have not been + * tuned!!! + * + * HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz + */ + +#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT) + +/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz + * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz + */ + +#ifdef CONFIG_SDIO_DMA +# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz + * DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz + */ + +#ifdef CONFIG_SDIO_DMA +# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* High-resolution timer + */ +#ifdef CONFIG_HRT_TIMER +# define HRT_TIMER 8 /* use timer8 for the HRT */ +# define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */ +#endif + +/* Alternate function pin selections ************************************************/ + +/* + * UARTs. + */ +#define GPIO_USART1_RX GPIO_USART1_RX_1 /* console in from IO */ +#define GPIO_USART1_TX 0 /* USART1 is RX-only */ + +#define GPIO_USART2_RX GPIO_USART2_RX_2 +#define GPIO_USART2_TX GPIO_USART2_TX_2 +#define GPIO_USART2_RTS GPIO_USART2_RTS_2 +#define GPIO_USART2_CTS GPIO_USART2_CTS_2 + +#define GPIO_USART3_RX GPIO_USART3_RX_3 +#define GPIO_USART3_TX GPIO_USART3_TX_3 +#define GPIO_USART2_RTS GPIO_USART2_RTS_2 +#define GPIO_USART2_CTS GPIO_USART2_CTS_2 + +#define GPIO_UART4_RX GPIO_UART4_RX_1 +#define GPIO_UART4_TX GPIO_UART4_TX_1 + +#define GPIO_USART6_RX GPIO_USART6_RX_1 +#define GPIO_USART6_TX GPIO_USART6_TX_1 + +#define GPIO_UART7_RX GPIO_UART7_RX_1 +#define GPIO_UART7_TX GPIO_UART7_TX_1 + +/* UART8 has no alternate pin config */ + +/* UART RX DMA configurations */ +#define DMAMAP_USART1_RX DMAMAP_USART1_RX_2 +#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2 + +/* + * PWM + * + * Six PWM outputs are configured. + * + * Pins: + * + * CH1 : PE14 : TIM1_CH4 + * CH2 : PE13 : TIM1_CH3 + * CH3 : PE11 : TIM1_CH2 + * CH4 : PE9 : TIM1_CH1 + * CH5 : PD13 : TIM4_CH2 + * CH6 : PD14 : TIM4_CH3 + * + */ +#define GPIO_TIM1_CH1OUT GPIO_TIM1_CH1OUT_2 +#define GPIO_TIM1_CH2OUT GPIO_TIM1_CH2OUT_2 +#define GPIO_TIM1_CH3OUT GPIO_TIM1_CH3OUT_2 +#define GPIO_TIM1_CH4OUT GPIO_TIM1_CH4OUT_2 +#define GPIO_TIM4_CH2OUT GPIO_TIM4_CH2OUT_2 +#define GPIO_TIM4_CH3OUT GPIO_TIM4_CH3OUT_2 + +/* + * CAN + * + * CAN1 is routed to the onboard transceiver. + * CAN2 is routed to the expansion connector. + */ + +#define GPIO_CAN1_RX GPIO_CAN1_RX_3 +#define GPIO_CAN1_TX GPIO_CAN1_TX_3 +#define GPIO_CAN2_RX GPIO_CAN2_RX_1 +#define GPIO_CAN2_TX GPIO_CAN2_TX_2 + +/* + * I2C + * + * The optional _GPIO configurations allow the I2C driver to manually + * reset the bus to clear stuck slaves. They match the pin configuration, + * but are normally-high GPIOs. + */ +#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 +#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 +#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8) +#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9) + +#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1 +#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1 +#define GPIO_I2C2_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN10) +#define GPIO_I2C2_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN11) + +/* + * I2C busses + */ +#define PX4_I2C_BUS_EXPANSION 1 +#define PX4_I2C_BUS_LED 2 + +/* + * Devices on the onboard bus. + * + * Note that these are unshifted addresses. + */ +#define PX4_I2C_OBDEV_LED 0x5a + +/* + * SPI + * + * There are sensors on SPI1, and SPI2 is connected to the FRAM. + */ +#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 +#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 +#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 + +#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 +#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 +#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2 + +/* + * Use these in place of the spi_dev_e enumeration to + * select a specific SPI device on SPI1 + */ +#define PX4_SPIDEV_GYRO 1 +#define PX4_SPIDEV_ACCEL_MAG 2 +#define PX4_SPIDEV_BARO 3 + +/* + * Tone alarm output + */ +#define TONE_ALARM_TIMER 2 /* timer 3 */ +#define TONE_ALARM_CHANNEL 1 /* channel 3 */ +#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF2|GPIO_SPEED_2MHz|GPIO_FLOAT|GPIO_PUSHPULL|GPIO_PORTA|GPIO_PIN15) + +/************************************************************************************ + * Public Data + ************************************************************************************/ + +#ifndef __ASSEMBLY__ + +#undef EXTERN +#if defined(__cplusplus) +#define EXTERN extern "C" +extern "C" { +#else +#define EXTERN extern +#endif + +/************************************************************************************ + * Public Function Prototypes + ************************************************************************************/ +/************************************************************************************ + * Name: stm32_boardinitialize + * + * Description: + * All STM32 architectures must provide the following entry point. This entry point + * is called early in the intitialization -- after all memory has been configured + * and mapped but before any devices have been initialized. + * + ************************************************************************************/ + +EXTERN void stm32_boardinitialize(void); + +#undef EXTERN +#if defined(__cplusplus) +} +#endif + +#endif /* __ASSEMBLY__ */ +#endif /* __ARCH_BOARD_BOARD_H */ diff --git a/nuttx/configs/px4fmuv2/include/nsh_romfsimg.h b/nuttx/configs/px4fmuv2/include/nsh_romfsimg.h new file mode 100644 index 000000000..15e4e7a8d --- /dev/null +++ b/nuttx/configs/px4fmuv2/include/nsh_romfsimg.h @@ -0,0 +1,42 @@ +/**************************************************************************** + * + * Copyright (C) 2013 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * nsh_romfsetc.h + * + * This file is a stub for 'make export' purposes; the actual ROMFS + * must be supplied by the library client. + */ + +extern unsigned char romfs_img[]; +extern unsigned int romfs_img_len; diff --git a/nuttx/configs/px4fmuv2/nsh/Make.defs b/nuttx/configs/px4fmuv2/nsh/Make.defs new file mode 100644 index 000000000..3e6f88bd3 --- /dev/null +++ b/nuttx/configs/px4fmuv2/nsh/Make.defs @@ -0,0 +1,3 @@ +include ${TOPDIR}/.config + +include $(TOPDIR)/configs/px4fmu/common/Make.defs diff --git a/nuttx/configs/px4fmuv2/nsh/appconfig b/nuttx/configs/px4fmuv2/nsh/appconfig new file mode 100644 index 000000000..fbcb67dcf --- /dev/null +++ b/nuttx/configs/px4fmuv2/nsh/appconfig @@ -0,0 +1,143 @@ +############################################################################ +# configs/px4fmu/nsh/appconfig +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +# Path to example in apps/examples containing the user_start entry point + +CONFIGURED_APPS += examples/nsh + +# The NSH application library +CONFIGURED_APPS += nshlib +CONFIGURED_APPS += system/readline + +# System library - utility functions +CONFIGURED_APPS += systemlib +CONFIGURED_APPS += systemlib/mixer + +# Math library +ifneq ($(CONFIG_APM),y) +CONFIGURED_APPS += mathlib +CONFIGURED_APPS += mathlib/CMSIS +CONFIGURED_APPS += examples/math_demo +endif + +# Control library +ifneq ($(CONFIG_APM),y) +CONFIGURED_APPS += controllib +CONFIGURED_APPS += examples/control_demo +CONFIGURED_APPS += examples/kalman_demo +endif + +# System utility commands +CONFIGURED_APPS += systemcmds/reboot +CONFIGURED_APPS += systemcmds/perf +CONFIGURED_APPS += systemcmds/top +CONFIGURED_APPS += systemcmds/boardinfo +CONFIGURED_APPS += systemcmds/mixer +# No I2C EEPROM - need new param interface +#CONFIGURED_APPS += systemcmds/eeprom +#CONFIGURED_APPS += systemcmds/param +CONFIGURED_APPS += systemcmds/pwm +CONFIGURED_APPS += systemcmds/bl_update +CONFIGURED_APPS += systemcmds/preflight_check +CONFIGURED_APPS += systemcmds/delay_test + +# Tutorial code from +# https://pixhawk.ethz.ch/px4/dev/hello_sky +# CONFIGURED_APPS += examples/px4_simple_app + +# Tutorial code from +# https://pixhawk.ethz.ch/px4/dev/deamon +# CONFIGURED_APPS += examples/px4_deamon_app + +# Tutorial code from +# https://pixhawk.ethz.ch/px4/dev/debug_values +# CONFIGURED_APPS += examples/px4_mavlink_debug + +# Shared object broker; required by many parts of the system. +CONFIGURED_APPS += uORB + +CONFIGURED_APPS += mavlink +CONFIGURED_APPS += mavlink_onboard +CONFIGURED_APPS += commander +CONFIGURED_APPS += sdlog +CONFIGURED_APPS += sensors + +ifneq ($(CONFIG_APM),y) +#CONFIGURED_APPS += ardrone_interface +CONFIGURED_APPS += multirotor_att_control +CONFIGURED_APPS += multirotor_pos_control +#CONFIGURED_APPS += fixedwing_control +CONFIGURED_APPS += fixedwing_att_control +CONFIGURED_APPS += fixedwing_pos_control +CONFIGURED_APPS += position_estimator +CONFIGURED_APPS += attitude_estimator_ekf +CONFIGURED_APPS += hott_telemetry +endif + +# Hacking tools +# XXX needs updating for new i2c config +#CONFIGURED_APPS += systemcmds/i2c + +# Communication and Drivers +CONFIGURED_APPS += drivers/boards/px4fmuv2 +CONFIGURED_APPS += drivers/device +# XXX needs conversion to SPI +#CONFIGURED_APPS += drivers/ms5611 +CONFIGURED_APPS += drivers/l3gd20 +# XXX needs conversion to serial +#CONFIGURED_APPS += drivers/px4io +CONFIGURED_APPS += drivers/stm32 +#CONFIGURED_APPS += drivers/led +CONFIGURED_APPS += drivers/blinkm +CONFIGURED_APPS += drivers/stm32/tone_alarm +CONFIGURED_APPS += drivers/stm32/adc +#CONFIGURED_APPS += drivers/px4fmu +CONFIGURED_APPS += drivers/hil +CONFIGURED_APPS += drivers/gps +CONFIGURED_APPS += drivers/mb12xx + +# Testing stuff +CONFIGURED_APPS += px4/sensors_bringup +CONFIGURED_APPS += px4/tests + +ifeq ($(CONFIG_CAN),y) +#CONFIGURED_APPS += examples/can +endif + +#ifeq ($(CONFIG_USBDEV),y) +#ifeq ($(CONFIG_CDCACM),y) +CONFIGURED_APPS += examples/cdcacm +#endif +#endif diff --git a/nuttx/configs/px4fmuv2/nsh/defconfig b/nuttx/configs/px4fmuv2/nsh/defconfig new file mode 100755 index 000000000..8e9feef65 --- /dev/null +++ b/nuttx/configs/px4fmuv2/nsh/defconfig @@ -0,0 +1,1050 @@ +############################################################################ +# configs/px4fmu/nsh/defconfig +# +# Copyright (C) 2012 PX4 Development Team. All rights reserved. +# Copyright (C) 2011-2012 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +# +# architecture selection +# +# CONFIG_ARCH - identifies the arch subdirectory and, hence, the +# processor architecture. +# CONFIG_ARCH_family - for use in C code. This identifies the +# particular chip family that the architecture is implemented +# in. +# CONFIG_ARCH_architecture - for use in C code. This identifies the +# specific architecture within the chip family. +# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory +# CONFIG_ARCH_CHIP_name - For use in C code +# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence, +# the board that supports the particular chip or SoC. +# CONFIG_ARCH_BOARD_name - for use in C code +# CONFIG_ENDIAN_BIG - define if big endian (default is little endian) +# CONFIG_BOARD_LOOPSPERMSEC - for delay loops +# CONFIG_DRAM_SIZE - Describes the installed DRAM. +# CONFIG_DRAM_START - The start address of DRAM (physical) +# CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization +# CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU). +# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt +# stack. If defined, this symbol is the size of the interrupt +# stack in bytes. If not defined, the user task stacks will be +# used during interrupt handling. +# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions +# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader. +# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture. +# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture. +# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that +# cause a 100 second delay during boot-up. This 100 second delay +# serves no purpose other than it allows you to calibrate +# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure +# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until +# the delay actually is 100 seconds. +# CONFIG_ARCH_DMA - Support DMA initialization +# +CONFIG_ARCH="arm" +CONFIG_ARCH_ARM=y +CONFIG_ARCH_CORTEXM4=y +CONFIG_ARCH_CHIP="stm32" +CONFIG_ARCH_CHIP_STM32F427V=y +CONFIG_ARCH_BOARD="px4fmuv2" +CONFIG_ARCH_BOARD_PX4FMUV2=y +CONFIG_BOARD_LOOPSPERMSEC=16717 +CONFIG_DRAM_SIZE=0x00040000 +CONFIG_DRAM_START=0x20000000 +CONFIG_ARCH_IRQPRIO=y +CONFIG_ARCH_FPU=y +CONFIG_ARCH_INTERRUPTSTACK=n +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARCH_BOOTLOADER=n +CONFIG_ARCH_LEDS=n +CONFIG_ARCH_BUTTONS=n +CONFIG_ARCH_CALIBRATION=n +CONFIG_ARCH_DMA=y +CONFIG_ARCH_MATH_H=y + +CONFIG_ARMV7M_CMNVECTOR=y +CONFIG_STM32_STM32F427=y + +# +# JTAG Enable settings (by default JTAG-DP and SW-DP are enabled): +# +# CONFIG_STM32_DFU - Use the DFU bootloader, not JTAG (ignored) +# +# JTAG Enable options: +# +# CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) +# CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP) +# but without JNTRST. +# CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled +# +CONFIG_STM32_DFU=n +CONFIG_STM32_JTAG_FULL_ENABLE=y +CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n +CONFIG_STM32_JTAG_SW_ENABLE=n + +# +# On-chip CCM SRAM configuration +# +# CONFIG_STM32_CCMEXCLUDE - Exclude CCM SRAM from the HEAP. You would need +# to do this if DMA is enabled to prevent non-DMA-able CCM memory from +# being a part of the stack. +# + +# +# On-board FSMC SRAM configuration +# +# CONFIG_STM32_FSMC - Required. See below +# CONFIG_MM_REGIONS - Required. Must be 2 or 3 (see above) +# +# CONFIG_STM32_FSMC_SRAM=y - Indicates that SRAM is available via the +# FSMC (as opposed to an LCD or FLASH). +# CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space +# CONFIG_HEAP2_END - The end (+1) of the SRAM in the FSMC address space +# +#CONFIG_STM32_FSMC_SRAM=n +#CONFIG_HEAP2_BASE=0x64000000 +#CONFIG_HEAP2_END=(0x64000000+(2*1024*1024)) + +# +# Individual subsystems can be enabled: +# +# This set is exhaustive for PX4FMU and should be safe to cut and +# paste into any other config. +# +# AHB1: +CONFIG_STM32_CRC=n +CONFIG_STM32_BKPSRAM=y +CONFIG_STM32_CCMDATARAM=y +CONFIG_STM32_DMA1=y +CONFIG_STM32_DMA2=y +CONFIG_STM32_ETHMAC=n +CONFIG_STM32_OTGHS=n +# AHB2: +CONFIG_STM32_DCMI=n +CONFIG_STM32_CRYP=n +CONFIG_STM32_HASH=n +CONFIG_STM32_RNG=n +CONFIG_STM32_OTGFS=y +# AHB3: +CONFIG_STM32_FSMC=n +# APB1: +CONFIG_STM32_TIM2=n +CONFIG_STM32_TIM3=y +CONFIG_STM32_TIM4=y +CONFIG_STM32_TIM5=n +CONFIG_STM32_TIM6=n +CONFIG_STM32_TIM7=n +CONFIG_STM32_TIM12=n +CONFIG_STM32_TIM13=n +CONFIG_STM32_TIM14=n +CONFIG_STM32_WWDG=y +CONFIG_STM32_IWDG=n +CONFIG_STM32_SPI2=y +CONFIG_STM32_SPI3=n +CONFIG_STM32_USART2=y +CONFIG_STM32_USART3=y +CONFIG_STM32_UART4=y +CONFIG_STM32_UART5=n +CONFIG_STM32_UART7=y +CONFIG_STM32_UART8=y +CONFIG_STM32_I2C1=y +CONFIG_STM32_I2C2=y +CONFIG_STM32_I2C3=n +CONFIG_STM32_CAN1=n +CONFIG_STM32_CAN2=n +CONFIG_STM32_DAC=n +CONFIG_STM32_PWR=y +# APB2: +CONFIG_STM32_TIM1=y +CONFIG_STM32_TIM8=n +CONFIG_STM32_USART1=y +CONFIG_STM32_USART6=y +# We use our own driver, but leave this on. +CONFIG_STM32_ADC1=y +CONFIG_STM32_ADC2=n +CONFIG_STM32_ADC3=n +CONFIG_STM32_SDIO=n +CONFIG_STM32_SPI1=y +CONFIG_STM32_SYSCFG=y +CONFIG_STM32_TIM9=y +CONFIG_STM32_TIM10=y +CONFIG_STM32_TIM11=y + +# +# Enable single wire support. If this is not defined, then this mode cannot +# be enabled. +# +CONFIG_STM32_USART_SINGLEWIRE=y + +# +# We want the flash prefetch on for max performance. +# +STM32_FLASH_PREFETCH=y + +# +# STM32F40xxx specific serial device driver settings +# +# CONFIG_SERIAL_TERMIOS - Serial driver supports termios.h interfaces (tcsetattr, +# tcflush, etc.). If this is not defined, then the terminal settings (baud, +# parity, etc.) are not configurable at runtime; serial streams cannot be +# flushed, etc. +# CONFIG_SERIAL_CONSOLE_REINIT - re-initializes the console serial port +# immediately after creating the /dev/console device. This is required +# if the console serial port has RX DMA enabled. +# +# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the +# console and ttys0 (default is the USART1). +# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received. +# This specific the size of the receive buffer +# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before +# being sent. This specific the size of the transmit buffer +# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be +# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8. +# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity +# CONFIG_USARTn_2STOP - Two stop bits +# +CONFIG_SERIAL_TERMIOS=y +CONFIG_SERIAL_CONSOLE_REINIT=y +CONFIG_STANDARD_SERIAL=y + +CONFIG_UART8_SERIAL_CONSOLE=y + +#Mavlink messages can be bigger than 128 +CONFIG_USART1_TXBUFSIZE=512 +CONFIG_USART2_TXBUFSIZE=256 +CONFIG_USART3_TXBUFSIZE=256 +CONFIG_UART4_TXBUFSIZE=256 +CONFIG_USART6_TXBUFSIZE=128 +CONFIG_UART7_TXBUFSIZE=256 +CONFIG_UART8_TXBUFSIZE=256 + +CONFIG_USART1_RXBUFSIZE=512 +CONFIG_USART2_RXBUFSIZE=256 +CONFIG_USART3_RXBUFSIZE=256 +CONFIG_UART4_RXBUFSIZE=256 +CONFIG_USART6_RXBUFSIZE=256 +CONFIG_UART7_RXBUFSIZE=256 +CONFIG_UART8_RXBUFSIZE=256 + +CONFIG_USART1_BAUD=115200 +CONFIG_USART2_BAUD=115200 +CONFIG_USART3_BAUD=115200 +CONFIG_UART4_BAUD=115200 +CONFIG_USART6_BAUD=9600 +CONFIG_UART7_BAUD=115200 +CONFIG_UART8_BAUD=57600 + +CONFIG_USART1_BITS=8 +CONFIG_USART2_BITS=8 +CONFIG_USART3_BITS=8 +CONFIG_UART4_BITS=8 +CONFIG_USART6_BITS=8 +CONFIG_UART7_BITS=8 +CONFIG_UART8_BITS=8 + +CONFIG_USART1_PARITY=0 +CONFIG_USART2_PARITY=0 +CONFIG_USART3_PARITY=0 +CONFIG_UART4_PARITY=0 +CONFIG_USART6_PARITY=0 +CONFIG_UART7_PARITY=0 +CONFIG_UART8_PARITY=0 + +CONFIG_USART1_2STOP=0 +CONFIG_USART2_2STOP=0 +CONFIG_USART3_2STOP=0 +CONFIG_UART4_2STOP=0 +CONFIG_USART6_2STOP=0 +CONFIG_UART7_2STOP=0 +CONFIG_UART8_2STOP=0 + +CONFIG_USART1_RXDMA=y +CONFIG_USART2_RXDMA=y +CONFIG_USART3_RXDMA=n +CONFIG_UART4_RXDMA=n +CONFIG_USART6_RXDMA=y +CONFIG_UART7_RXDMA=n +CONFIG_UART8_RXDMA=n + +# +# PX4FMU specific driver settings +# +# CONFIG_HRT_TIMER +# Enables the high-resolution timer. The board definition must +# set HRT_TIMER and HRT_TIMER_CHANNEL to the timer and capture/ +# compare channels to be used. +# CONFIG_HRT_PPM +# Enables R/C PPM input using the HRT. The board definition must +# set HRT_PPM_CHANNEL to the timer capture/compare channel to be +# used, and define GPIO_PPM_IN to configure the appropriate timer +# GPIO. +# +CONFIG_HRT_TIMER=y +CONFIG_HRT_PPM=n + +# +# STM32F40xxx specific SPI device driver settings +# +CONFIG_SPI_EXCHANGE=y +# DMA needs more work, not implemented on STM32F4x yet +#CONFIG_STM32_SPI_DMA=y + +# +# STM32F40xxx specific CAN device driver settings +# +# CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or +# CONFIG_STM32_CAN2 must also be defined) +# CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default +# Standard 11-bit IDs. +# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages. +# Default: 8 +# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests. +# Default: 4 +# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback +# mode for testing. The STM32 CAN driver does support loopback mode. +# CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined. +# CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined. +# CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6 +# CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7 +# +CONFIG_CAN=n +CONFIG_CAN_EXTID=n +#CONFIG_CAN_FIFOSIZE +#CONFIG_CAN_NPENDINGRTR +CONFIG_CAN_LOOPBACK=n +CONFIG_CAN1_BAUD=700000 +CONFIG_CAN2_BAUD=700000 + + +# XXX remove after integration testing +# Allow 180 us per byte, a wide margin for the 400 KHz clock we're using +# e.g. 9.6 ms for an EEPROM page write, 0.9 ms for a MAG update +CONFIG_STM32_I2CTIMEOUS_PER_BYTE=200 +# Constant overhead for generating I2C start / stop conditions +CONFIG_STM32_I2CTIMEOUS_START_STOP=700 +# XXX this is bad and we want it gone +CONFIG_I2C_WRITEREAD=y + +# +# I2C configuration +# +CONFIG_I2C=y +CONFIG_I2C_POLLED=n +CONFIG_I2C_TRANSFER=y +CONFIG_I2C_TRACE=n +CONFIG_I2C_RESET=y +# XXX fixed per-transaction timeout +CONFIG_STM32_I2CTIMEOMS=10 + + +# XXX re-enable after integration testing + +# +# I2C configuration +# +#CONFIG_I2C=y +#CONFIG_I2C_POLLED=y +#CONFIG_I2C_TRANSFER=y +#CONFIG_I2C_TRACE=n +#CONFIG_I2C_RESET=y + +# Dynamic timeout +#CONFIG_STM32_I2C_DYNTIMEO=y +#CONFIG_STM32_I2C_DYNTIMEO_STARTSTOP=500 +#CONFIG_STM32_I2C_DYNTIMEO_USECPERBYTE=200 + +# Fixed per-transaction timeout +#CONFIG_STM32_I2CTIMEOSEC=0 +#CONFIG_STM32_I2CTIMEOMS=10 + + + + + + +# +# General build options +# +# CONFIG_RRLOAD_BINARY - make the rrload binary format used with +# BSPs from www.ridgerun.com using the tools/mkimage.sh script +# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format +# used with many different loaders using the GNU objcopy program +# Should not be selected if you are not using the GNU toolchain. +# CONFIG_RAW_BINARY - make a raw binary format file used with many +# different loaders using the GNU objcopy program. This option +# should not be selected if you are not using the GNU toolchain. +# CONFIG_HAVE_LIBM - toolchain supports libm.a +# +CONFIG_RRLOAD_BINARY=n +CONFIG_INTELHEX_BINARY=n +CONFIG_MOTOROLA_SREC=n +CONFIG_RAW_BINARY=y +CONFIG_HAVE_LIBM=y + +# +# General OS setup +# +# CONFIG_APPS_DIR - Identifies the relative path to the directory +# that builds the application to link with NuttX. Default: ../apps +# CONFIG_DEBUG - enables built-in debug options +# CONFIG_DEBUG_VERBOSE - enables verbose debug output +# CONFIG_DEBUG_SYMBOLS - build without optimization and with +# debug symbols (needed for use with a debugger). +# CONFIG_HAVE_CXX - Enable support for C++ +# CONFIG_HAVE_CXXINITIALIZE - The platform-specific logic includes support +# for initialization of static C++ instances for this architecture +# and for the selected toolchain (via up_cxxinitialize()). +# CONFIG_MM_REGIONS - If the architecture includes multiple +# regions of memory to allocate from, this specifies the +# number of memory regions that the memory manager must +# handle and enables the API mm_addregion(start, end); +# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot +# time console output +# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz +# or MSEC_PER_TICK=10. This setting may be defined to +# inform NuttX that the processor hardware is providing +# system timer interrupts at some interrupt interval other +# than 10 msec. +# CONFIG_RR_INTERVAL - The round robin timeslice will be set +# this number of milliseconds; Round robin scheduling can +# be disabled by setting this value to zero. +# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in +# scheduler to monitor system performance +# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a +# task name to save in the TCB. Useful if scheduler +# instrumentation is selected. Set to zero to disable. +# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY - +# Used to initialize the internal time logic. +# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions. +# You would only need this if you are concerned about accurate +# time conversions in the past or in the distant future. +# CONFIG_JULIAN_TIME - Enables Julian time conversions. You +# would only need this if you are concerned about accurate +# time conversion in the distand past. You must also define +# CONFIG_GREGORIAN_TIME in order to use Julian time. +# CONFIG_DEV_CONSOLE - Set if architecture-specific logic +# provides /dev/console. Enables stdout, stderr, stdin. +# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console +# driver (minimul support) +# CONFIG_MUTEX_TYPES: Set to enable support for recursive and +# errorcheck mutexes. Enables pthread_mutexattr_settype(). +# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority +# inheritance on mutexes and semaphores. +# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority +# inheritance is enabled. It defines the maximum number of +# different threads (minus one) that can take counts on a +# semaphore with priority inheritance support. This may be +# set to zero if priority inheritance is disabled OR if you +# are only using semaphores as mutexes (only one holder) OR +# if no more than two threads participate using a counting +# semaphore. +# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled, +# then this setting is the maximum number of higher priority +# threads (minus 1) than can be waiting for another thread +# to release a count on a semaphore. This value may be set +# to zero if no more than one thread is expected to wait for +# a semaphore. +# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors +# by task_create() when a new task is started. If set, all +# files/drivers will appear to be closed in the new task. +# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first +# three file descriptors (stdin, stdout, stderr) by task_create() +# when a new task is started. If set, all files/drivers will +# appear to be closed in the new task except for stdin, stdout, +# and stderr. +# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket +# desciptors by task_create() when a new task is started. If +# set, all sockets will appear to be closed in the new task. +# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to +# handle delayed processing from interrupt handlers. This feature +# is required for some drivers but, if there are not complaints, +# can be safely disabled. The worker thread also performs +# garbage collection -- completing any delayed memory deallocations +# from interrupt handlers. If the worker thread is disabled, +# then that clean will be performed by the IDLE thread instead +# (which runs at the lowest of priority and may not be appropriate +# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE +# is enabled, then the following options can also be used: +# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker +# thread. Default: 192 +# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for +# work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker +# thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up +# the worker thread. Default: 4 +# +# CONFIG_SCHED_LPWORK. If CONFIG_SCHED_WORKQUEUE is defined, then a single +# work queue is created by default. If CONFIG_SCHED_LPWORK is also defined +# then an additional, lower-priority work queue will also be created. This +# lower priority work queue is better suited for more extended processing +# (such as file system clean-up operations) +# CONFIG_SCHED_LPWORKPRIORITY - The execution priority of the lower priority +# worker thread. Default: 50 +# CONFIG_SCHED_LPWORKPERIOD - How often the lower priority worker thread +# checks for work in units of microseconds. Default: 50*1000 (50 MS). +# CONFIG_SCHED_LPWORKSTACKSIZE - The stack size allocated for the lower +# priority worker thread. Default: CONFIG_IDLETHREAD_STACKSIZE. +# CONFIG_SCHED_WAITPID - Enable the waitpid() API +# CONFIG_SCHED_ATEXIT - Enabled the atexit() API +# +CONFIG_USER_ENTRYPOINT="nsh_main" +#CONFIG_APPS_DIR= +CONFIG_DEBUG=y +CONFIG_DEBUG_VERBOSE=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEBUG_FS=n +CONFIG_DEBUG_GRAPHICS=n +CONFIG_DEBUG_LCD=n +CONFIG_DEBUG_USB=n +CONFIG_DEBUG_NET=n +CONFIG_DEBUG_RTC=n +CONFIG_DEBUG_ANALOG=n +CONFIG_DEBUG_PWM=n +CONFIG_DEBUG_CAN=n +CONFIG_DEBUG_I2C=n +CONFIG_DEBUG_INPUT=n + +CONFIG_HAVE_CXX=y +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_MM_REGIONS=2 +CONFIG_ARCH_LOWPUTC=y +CONFIG_MSEC_PER_TICK=1 +CONFIG_RR_INTERVAL=0 +CONFIG_SCHED_INSTRUMENTATION=y +CONFIG_TASK_NAME_SIZE=24 +CONFIG_START_YEAR=1970 +CONFIG_START_MONTH=1 +CONFIG_START_DAY=1 +CONFIG_GREGORIAN_TIME=n +CONFIG_JULIAN_TIME=n +CONFIG_DEV_CONSOLE=y +CONFIG_DEV_LOWCONSOLE=n +CONFIG_MUTEX_TYPES=n +CONFIG_PRIORITY_INHERITANCE=y +CONFIG_SEM_PREALLOCHOLDERS=0 +CONFIG_SEM_NNESTPRIO=8 +CONFIG_FDCLONE_DISABLE=n +CONFIG_FDCLONE_STDIO=y +CONFIG_SDCLONE_DISABLE=y +CONFIG_SCHED_WORKQUEUE=y +CONFIG_SCHED_WORKPRIORITY=192 +CONFIG_SCHED_WORKPERIOD=5000 +CONFIG_SCHED_WORKSTACKSIZE=2048 +CONFIG_SCHED_LPWORK=y +CONFIG_SCHED_LPWORKPRIORITY=50 +CONFIG_SCHED_LPWORKPERIOD=50000 +CONFIG_SCHED_LPWORKSTACKSIZE=2048 +CONFIG_SIG_SIGWORK=4 +CONFIG_SCHED_WAITPID=y +CONFIG_SCHED_ATEXIT=n + +# +# System Logging +# +# CONFIG_SYSLOG - Enables the System Logging feature. +# CONFIG_RAMLOG - Enables the RAM logging feature +# CONFIG_RAMLOG_CONSOLE - Use the RAM logging device as a system console. +# If this feature is enabled (along with CONFIG_DEV_CONSOLE), then all +# console output will be re-directed to a circular buffer in RAM. This +# is useful, for example, if the only console is a Telnet console. Then +# in that case, console output from non-Telnet threads will go to the +# circular buffer and can be viewed using the NSH 'dmesg' command. +# CONFIG_RAMLOG_SYSLOG - Use the RAM logging device for the syslogging +# interface. If this feature is enabled (along with CONFIG_SYSLOG), +# then all debug output (only) will be re-directed to the circular +# buffer in RAM. This RAM log can be view from NSH using the 'dmesg' +# command. +# CONFIG_RAMLOG_NPOLLWAITERS - The number of threads than can be waiting +# for this driver on poll(). Default: 4 +# +# If CONFIG_RAMLOG_CONSOLE or CONFIG_RAMLOG_SYSLOG is selected, then the +# following may also be provided: +# +# CONFIG_RAMLOG_CONSOLE_BUFSIZE - Size of the console RAM log. Default: 1024 +# + +CONFIG_SYSLOG=n +CONFIG_RAMLOG=n +CONFIG_RAMLOG_CONSOLE=n +CONFIG_RAMLOG_SYSLOG=n +#CONFIG_RAMLOG_NPOLLWAITERS +#CONFIG_RAMLOG_CONSOLE_BUFSIZE + +# +# The following can be used to disable categories of +# APIs supported by the OS. If the compiler supports +# weak functions, then it should not be necessary to +# disable functions unless you want to restrict usage +# of those APIs. +# +# There are certain dependency relationships in these +# features. +# +# o mq_notify logic depends on signals to awaken tasks +# waiting for queues to become full or empty. +# o pthread_condtimedwait() depends on signals to wake +# up waiting tasks. +# +CONFIG_DISABLE_CLOCK=n +CONFIG_DISABLE_POSIX_TIMERS=n +CONFIG_DISABLE_PTHREAD=n +CONFIG_DISABLE_SIGNALS=n +CONFIG_DISABLE_MQUEUE=n +CONFIG_DISABLE_MOUNTPOINT=n +CONFIG_DISABLE_ENVIRON=n +CONFIG_DISABLE_POLL=n + +# +# Misc libc settings +# +# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a +# little smaller if we do not support fieldwidthes +# CONFIG_LIBC_FLOATINGPOINT - Enables printf("%f") +# CONFIG_LIBC_FIXEDPRECISION - Sets 7 digits after dot for printing: +# 5.1234567 +# CONFIG_HAVE_LONG_LONG - Enabled printf("%llu) +# +CONFIG_NOPRINTF_FIELDWIDTH=n +CONFIG_LIBC_FLOATINGPOINT=y +CONFIG_HAVE_LONG_LONG=y + +# +# Allow for architecture optimized implementations +# +# The architecture can provide optimized versions of the +# following to improve system performance +# +CONFIG_ARCH_MEMCPY=y +CONFIG_ARCH_MEMCMP=n +CONFIG_ARCH_MEMMOVE=n +CONFIG_ARCH_MEMSET=n +CONFIG_ARCH_STRCMP=n +CONFIG_ARCH_STRCPY=n +CONFIG_ARCH_STRNCPY=n +CONFIG_ARCH_STRLEN=n +CONFIG_ARCH_STRNLEN=n +CONFIG_ARCH_BZERO=n + +# +# Sizes of configurable things (0 disables) +# +# CONFIG_MAX_TASKS - The maximum number of simultaneously +# active tasks. This value must be a power of two. +# CONFIG_MAX_TASK_ARGS - This controls the maximum number of +# of parameters that a task may receive (i.e., maxmum value +# of 'argc') +# CONFIG_NPTHREAD_KEYS - The number of items of thread- +# specific data that can be retained +# CONFIG_NFILE_DESCRIPTORS - The maximum number of file +# descriptors (one for each open) +# CONFIG_NFILE_STREAMS - The maximum number of streams that +# can be fopen'ed +# CONFIG_NAME_MAX - The maximum size of a file name. +# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate +# on fopen. (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled +# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added +# to force automatic, line-oriented flushing the output buffer +# for putc(), fputc(), putchar(), puts(), fputs(), printf(), +# fprintf(), and vfprintf(). When a newline is encountered in +# the output string, the output buffer will be flushed. This +# (slightly) increases the NuttX footprint but supports the kind +# of behavior that people expect for printf(). +# CONFIG_NUNGET_CHARS - Number of characters that can be +# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0) +# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message +# structures. The system manages a pool of preallocated +# message structures to minimize dynamic allocations +# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with +# a fixed payload size given by this settin (does not include +# other message structure overhead. +# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that +# can be passed to a watchdog handler +# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog +# structures. The system manages a pool of preallocated +# watchdog structures to minimize dynamic allocations +# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX +# timer structures. The system manages a pool of preallocated +# timer structures to minimize dynamic allocations. Set to +# zero for all dynamic allocations. +# +CONFIG_MAX_TASKS=32 +CONFIG_MAX_TASK_ARGS=8 +CONFIG_NPTHREAD_KEYS=4 +CONFIG_NFILE_DESCRIPTORS=32 +CONFIG_NFILE_STREAMS=25 +CONFIG_NAME_MAX=32 +CONFIG_STDIO_BUFFER_SIZE=256 +CONFIG_STDIO_LINEBUFFER=y +CONFIG_NUNGET_CHARS=2 +CONFIG_PREALLOC_MQ_MSGS=4 +CONFIG_MQ_MAXMSGSIZE=32 +CONFIG_MAX_WDOGPARMS=2 +CONFIG_PREALLOC_WDOGS=50 +CONFIG_PREALLOC_TIMERS=50 + +# +# Filesystem configuration +# +# CONFIG_FS_FAT - Enable FAT filesystem support +# CONFIG_FAT_SECTORSIZE - Max supported sector size +# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3 +# file name support. +# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims +# patents on FAT long file name technology. Please read the +# disclaimer in the top-level COPYING file and only enable this +# feature if you understand these issues. +# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the +# default, maximum long file name is 255 bytes. This can eat up +# a lot of memory (especially stack space). If you are willing +# to live with some non-standard, short long file names, then +# define this value. A good choice would be the same value as +# selected for CONFIG_NAME_MAX which will limit the visibility +# of longer file names anyway. +# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support. +# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH. +# This must have one of the values of 0xff or 0x00. +# Default: 0xff. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name. +# Default: 255. +# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data, +# don't both with file chunks smaller than this number of data bytes. +# Default: 32. +# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean +# packing files together toward the end of the file or, if file are +# deleted at the end of the file, clean up can simply mean erasing +# the end of FLASH memory so that it can be re-used again. However, +# doing this can also harm the life of the FLASH part because it can +# mean that the tail end of the FLASH is re-used too often. This +# threshold determines if/when it is worth erased the tail end of FLASH +# and making it available for re-use (and possible over-wear). +# Default: 8192. +# CONFIG_FS_ROMFS - Enable ROMFS filesystem support +# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this +# option will enable a limited form of memory mapping that is +# implemented by copying whole files into memory. +# +CONFIG_FS_FAT=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_MAXFNAME=32 +CONFIG_FS_NXFFS=y +CONFIG_NXFFS_MAXNAMLEN=32 +CONFIG_NXFFS_TAILTHRESHOLD=2048 +CONFIG_NXFFS_PREALLOCATED=y +CONFIG_FS_ROMFS=y +CONFIG_FS_BINFS=y + +# +# SPI-based MMC/SD driver +# +# CONFIG_MMCSD_NSLOTS +# Number of MMC/SD slots supported by the driver +# CONFIG_MMCSD_READONLY +# Provide read-only access (default is read/write) +# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card. +# Default is 20MHz, current setting 24 MHz +# +CONFIG_MMCSD=n +# XXX need to rejig this for SDIO +#CONFIG_MMCSD_SPI=y +#CONFIG_MMCSD_NSLOTS=1 +#CONFIG_MMCSD_READONLY=n +#CONFIG_MMCSD_SPICLOCK=24000000 + +# +# Block driver buffering +# +# CONFIG_FS_READAHEAD +# Enable read-ahead buffering +# CONFIG_FS_WRITEBUFFER +# Enable write buffering +# +CONFIG_FS_READAHEAD=n +CONFIG_FS_WRITEBUFFER=n + +# +# RTC Configuration +# +# CONFIG_RTC - Enables general support for a hardware RTC. Specific +# architectures may require other specific settings. +# CONFIG_RTC_DATETIME - There are two general types of RTC: (1) A simple +# battery backed counter that keeps the time when power is down, and (2) +# A full date / time RTC the provides the date and time information, often +# in BCD format. If CONFIG_RTC_DATETIME is selected, it specifies this +# second kind of RTC. In this case, the RTC is used to "seed" the normal +# NuttX timer and the NuttX system timer provides for higher resoution +# time. +# CONFIG_RTC_HIRES - If CONFIG_RTC_DATETIME not selected, then the simple, +# battery backed counter is used. There are two different implementations +# of such simple counters based on the time resolution of the counter: +# The typical RTC keeps time to resolution of 1 second, usually +# supporting a 32-bit time_t value. In this case, the RTC is used to +# "seed" the normal NuttX timer and the NuttX timer provides for higher +# resoution time. If CONFIG_RTC_HIRES is enabled in the NuttX configuration, +# then the RTC provides higher resolution time and completely replaces the +# system timer for purpose of date and time. +# CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the frequency +# of the high resolution RTC must be provided. If CONFIG_RTC_HIRES is +# not defined, CONFIG_RTC_FREQUENCY is assumed to be one. +# CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an +# alarm. A callback function will be executed when the alarm goes off +# +CONFIG_RTC=n +CONFIG_RTC_DATETIME=y +CONFIG_RTC_HIRES=n +CONFIG_RTC_FREQUENCY=n +CONFIG_RTC_ALARM=n + +# +# USB Device Configuration +# +# CONFIG_USBDEV +# Enables USB device support +# CONFIG_USBDEV_ISOCHRONOUS +# Build in extra support for isochronous endpoints +# CONFIG_USBDEV_DUALSPEED +# Hardware handles high and full speed operation (USB 2.0) +# CONFIG_USBDEV_SELFPOWERED +# Will cause USB features to indicate that the device is +# self-powered +# CONFIG_USBDEV_MAXPOWER +# Maximum power consumption in mA +# CONFIG_USBDEV_TRACE +# Enables USB tracing for debug +# CONFIG_USBDEV_TRACE_NRECORDS +# Number of trace entries to remember +# +CONFIG_USBDEV=y +CONFIG_USBDEV_ISOCHRONOUS=n +CONFIG_USBDEV_DUALSPEED=n +CONFIG_USBDEV_SELFPOWERED=y +CONFIG_USBDEV_REMOTEWAKEUP=n +CONFIG_USBDEV_MAXPOWER=500 +CONFIG_USBDEV_TRACE=n +CONFIG_USBDEV_TRACE_NRECORDS=512 + +# +# USB serial device class driver (Standard CDC ACM class) +# +# CONFIG_CDCACM +# Enable compilation of the USB serial driver +# CONFIG_CDCACM_CONSOLE +# Configures the CDC/ACM serial port as the console device. +# CONFIG_CDCACM_EP0MAXPACKET +# Endpoint 0 max packet size. Default 64 +# CONFIG_CDCACM_EPINTIN +# The logical 7-bit address of a hardware endpoint that supports +# interrupt IN operation. Default 2. +# CONFIG_CDCACM_EPINTIN_FSSIZE +# Max package size for the interrupt IN endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPINTIN_HSSIZE +# Max package size for the interrupt IN endpoint if high speed mode. +# Default 64 +# CONFIG_CDCACM_EPBULKOUT +# The logical 7-bit address of a hardware endpoint that supports +# bulk OUT operation. Default 4. +# CONFIG_CDCACM_EPBULKOUT_FSSIZE +# Max package size for the bulk OUT endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPBULKOUT_HSSIZE +# Max package size for the bulk OUT endpoint if high speed mode. +# Default 512. +# CONFIG_CDCACM_EPBULKIN +# The logical 7-bit address of a hardware endpoint that supports +# bulk IN operation. Default 3. +# CONFIG_CDCACM_EPBULKIN_FSSIZE +# Max package size for the bulk IN endpoint if full speed mode. +# Default 64. +# CONFIG_CDCACM_EPBULKIN_HSSIZE +# Max package size for the bulk IN endpoint if high speed mode. +# Default 512. +# CONFIG_CDCACM_NWRREQS and CONFIG_CDCACM_NRDREQS +# The number of write/read requests that can be in flight. +# Default 256. +# CONFIG_CDCACM_VENDORID and CONFIG_CDCACM_VENDORSTR +# The vendor ID code/string. Default 0x0525 and "NuttX" +# 0x0525 is the Netchip vendor and should not be used in any +# products. This default VID was selected for compatibility with +# the Linux CDC ACM default VID. +# CONFIG_CDCACM_PRODUCTID and CONFIG_CDCACM_PRODUCTSTR +# The product ID code/string. Default 0xa4a7 and "CDC/ACM Serial" +# 0xa4a7 was selected for compatibility with the Linux CDC ACM +# default PID. +# CONFIG_CDCACM_RXBUFSIZE and CONFIG_CDCACM_TXBUFSIZE +# Size of the serial receive/transmit buffers. Default 256. +# +CONFIG_CDCACM=y +CONFIG_CDCACM_CONSOLE=n +#CONFIG_CDCACM_EP0MAXPACKET +CONFIG_CDCACM_EPINTIN=1 +#CONFIG_CDCACM_EPINTIN_FSSIZE +#CONFIG_CDCACM_EPINTIN_HSSIZE +CONFIG_CDCACM_EPBULKOUT=3 +#CONFIG_CDCACM_EPBULKOUT_FSSIZE +#CONFIG_CDCACM_EPBULKOUT_HSSIZE +CONFIG_CDCACM_EPBULKIN=2 +#CONFIG_CDCACM_EPBULKIN_FSSIZE +#CONFIG_CDCACM_EPBULKIN_HSSIZE +#CONFIG_CDCACM_NWRREQS +#CONFIG_CDCACM_NRDREQS +CONFIG_CDCACM_VENDORID=0x26AC +CONFIG_CDCACM_VENDORSTR="3D Robotics" +CONFIG_CDCACM_PRODUCTID=0x0010 +CONFIG_CDCACM_PRODUCTSTR="PX4 FMU v1.6" +#CONFIG_CDCACM_RXBUFSIZE +#CONFIG_CDCACM_TXBUFSIZE + + +# +# Settings for apps/nshlib +# +# CONFIG_NSH_BUILTIN_APPS - Support external registered, +# "named" applications that can be executed from the NSH +# command line (see apps/README.txt for more information). +# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer +# CONFIG_NSH_STRERROR - Use strerror(errno) +# CONFIG_NSH_LINELEN - Maximum length of one command line +# CONFIG_NSH_MAX_ARGUMENTS - Maximum number of arguments for command line +# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi +# CONFIG_NSH_DISABLESCRIPT - Disable scripting support +# CONFIG_NSH_DISABLEBG - Disable background commands +# CONFIG_NSH_ROMFSETC - Use startup script in /etc +# CONFIG_NSH_CONSOLE - Use serial console front end +# CONFIG_NSH_TELNET - Use telnetd console front end +# CONFIG_NSH_ARCHINIT - Platform provides architecture +# specific initialization (nsh_archinitialize()). +# +# If CONFIG_NSH_TELNET is selected: +# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size +# CONFIG_NSH_DHCPC - Obtain address using DHCP +# CONFIG_NSH_IPADDR - Provides static IP address +# CONFIG_NSH_DRIPADDR - Provides static router IP address +# CONFIG_NSH_NETMASK - Provides static network mask +# CONFIG_NSH_NOMAC - Use a bogus MAC address +# +# If CONFIG_NSH_ROMFSETC is selected: +# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint +# CONFIG_NSH_INITSCRIPT - Relative path to init script +# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor +# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size +# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor +# CONFIG_NSH_FATSECTSIZE - FAT FS sector size +# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors +# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint +# +CONFIG_BUILTIN=y +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_FILEIOSIZE=512 +CONFIG_NSH_STRERROR=y +CONFIG_NSH_LINELEN=128 +CONFIG_NSH_MAX_ARGUMENTS=12 +CONFIG_NSH_NESTDEPTH=8 +CONFIG_NSH_DISABLESCRIPT=n +CONFIG_NSH_DISABLEBG=n +CONFIG_NSH_ROMFSETC=y +CONFIG_NSH_ARCHROMFS=y +CONFIG_NSH_CONSOLE=y +CONFIG_NSH_USBCONSOLE=n +CONFIG_NSH_USBCONDEV="/dev/ttyACM0" +CONFIG_NSH_TELNET=n +CONFIG_NSH_ARCHINIT=y +CONFIG_NSH_IOBUFFER_SIZE=512 +CONFIG_NSH_DHCPC=n +CONFIG_NSH_NOMAC=y +CONFIG_NSH_IPADDR=0x0a000002 +CONFIG_NSH_DRIPADDR=0x0a000001 +CONFIG_NSH_NETMASK=0xffffff00 +CONFIG_NSH_ROMFSMOUNTPT="/etc" +CONFIG_NSH_INITSCRIPT="init.d/rcS" +CONFIG_NSH_ROMFSDEVNO=0 +CONFIG_NSH_ROMFSSECTSIZE=128 # Default 64, increased to allow for more than 64 folders on the sdcard +CONFIG_NSH_FATDEVNO=1 +CONFIG_NSH_FATSECTSIZE=512 +CONFIG_NSH_FATNSECTORS=1024 +CONFIG_NSH_FATMOUNTPT=/tmp + +# +# Architecture-specific NSH options +# +#CONFIG_NSH_MMCSDSPIPORTNO=3 +#CONFIG_NSH_MMCSDSLOTNO=0 +#CONFIG_NSH_MMCSDMINOR=0 + + +# +# Stack and heap information +# +# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP +# operation from FLASH but must copy initialized .data sections to RAM. +# (should also be =n for the STM3240G-EVAL which always runs from flash) +# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH +# but copy themselves entirely into RAM for better performance. +# CONFIG_CUSTOM_STACK - The up_ implementation will handle +# all stack operations outside of the nuttx model. +# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only) +# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack. +# This is the thread that (1) performs the inital boot of the system up +# to the point where user_start() is spawned, and (2) there after is the +# IDLE thread that executes only when there is no other thread ready to +# run. +# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate +# for the main user thread that begins at the user_start() entry point. +# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size +# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size +# CONFIG_HEAP_BASE - The beginning of the heap +# CONFIG_HEAP_SIZE - The size of the heap +# +CONFIG_BOOT_RUNFROMFLASH=n +CONFIG_BOOT_COPYTORAM=n +CONFIG_CUSTOM_STACK=n +CONFIG_STACK_POINTER= +# Idle thread needs 4096 bytes +# default 1 KB is not enough +# 4096 bytes +CONFIG_IDLETHREAD_STACKSIZE=6000 +# USERMAIN stack size probably needs to be around 4096 bytes +CONFIG_USERMAIN_STACKSIZE=4096 +CONFIG_PTHREAD_STACK_MIN=512 +CONFIG_PTHREAD_STACK_DEFAULT=2048 +CONFIG_HEAP_BASE= +CONFIG_HEAP_SIZE= + +# enable bindir +CONFIG_APPS_BINDIR=y diff --git a/nuttx/configs/px4fmuv2/nsh/setenv.sh b/nuttx/configs/px4fmuv2/nsh/setenv.sh new file mode 100755 index 000000000..265520997 --- /dev/null +++ b/nuttx/configs/px4fmuv2/nsh/setenv.sh @@ -0,0 +1,67 @@ +#!/bin/bash +# configs/stm3240g-eval/nsh/setenv.sh +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# + +if [ "$_" = "$0" ] ; then + echo "You must source this script, not run it!" 1>&2 + exit 1 +fi + +WD=`pwd` +if [ ! -x "setenv.sh" ]; then + echo "This script must be executed from the top-level NuttX build directory" + exit 1 +fi + +if [ -z "${PATH_ORIG}" ]; then + export PATH_ORIG="${PATH}" +fi + +# This the Cygwin path to the location where I installed the RIDE +# toolchain under windows. You will also have to edit this if you install +# the RIDE toolchain in any other location +#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Raisonance/Ride/arm-gcc/bin" + +# This the Cygwin path to the location where I installed the CodeSourcery +# toolchain under windows. You will also have to edit this if you install +# the CodeSourcery toolchain in any other location +export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin" + +# This the Cygwin path to the location where I build the buildroot +# toolchain. +#export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin" + +# Add the path to the toolchain to the PATH varialble +export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}" + +echo "PATH : ${PATH}" diff --git a/nuttx/configs/px4fmuv2/src/Makefile b/nuttx/configs/px4fmuv2/src/Makefile new file mode 100644 index 000000000..d4276f7fc --- /dev/null +++ b/nuttx/configs/px4fmuv2/src/Makefile @@ -0,0 +1,84 @@ +############################################################################ +# configs/px4fmu/src/Makefile +# +# Copyright (C) 2011 Gregory Nutt. All rights reserved. +# Author: Gregory Nutt <gnutt@nuttx.org> +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name NuttX nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +-include $(TOPDIR)/Make.defs + +CFLAGS += -I$(TOPDIR)/sched + +ASRCS = +AOBJS = $(ASRCS:.S=$(OBJEXT)) + +CSRCS = empty.c +COBJS = $(CSRCS:.c=$(OBJEXT)) + +SRCS = $(ASRCS) $(CSRCS) +OBJS = $(AOBJS) $(COBJS) + +ARCH_SRCDIR = $(TOPDIR)/arch/$(CONFIG_ARCH)/src +ifeq ($(WINTOOL),y) + CFLAGS += -I "${shell cygpath -w $(ARCH_SRCDIR)/chip}" \ + -I "${shell cygpath -w $(ARCH_SRCDIR)/common}" \ + -I "${shell cygpath -w $(ARCH_SRCDIR)/armv7-m}" +else + CFLAGS += -I$(ARCH_SRCDIR)/chip -I$(ARCH_SRCDIR)/common -I$(ARCH_SRCDIR)/armv7-m +endif + +all: libboard$(LIBEXT) + +$(AOBJS): %$(OBJEXT): %.S + $(call ASSEMBLE, $<, $@) + +$(COBJS) $(LINKOBJS): %$(OBJEXT): %.c + $(call COMPILE, $<, $@) + +libboard$(LIBEXT): $(OBJS) + $(call ARCHIVE, $@, $(OBJS)) + +.depend: Makefile $(SRCS) + $(Q) $(MKDEP) $(CC) -- $(CFLAGS) -- $(SRCS) >Make.dep + $(Q) touch $@ + +depend: .depend + +clean: + $(call DELFILE, libboard$(LIBEXT)) + $(call CLEAN) + +distclean: clean + $(call DELFILE, Make.dep) + $(call DELFILE, .depend) + +-include Make.dep + diff --git a/nuttx/configs/px4fmuv2/src/empty.c b/nuttx/configs/px4fmuv2/src/empty.c new file mode 100644 index 000000000..ace900866 --- /dev/null +++ b/nuttx/configs/px4fmuv2/src/empty.c @@ -0,0 +1,4 @@ +/* + * There are no source files here, but libboard.a can't be empty, so + * we have this empty source file to keep it company. + */ |