diff options
Diffstat (limited to 'src/drivers/ardrone_interface')
-rw-r--r-- | src/drivers/ardrone_interface/ardrone_interface.c | 36 | ||||
-rw-r--r-- | src/drivers/ardrone_interface/ardrone_motor_control.c | 2 |
2 files changed, 15 insertions, 23 deletions
diff --git a/src/drivers/ardrone_interface/ardrone_interface.c b/src/drivers/ardrone_interface/ardrone_interface.c index e5bb772b3..9d2c1441d 100644 --- a/src/drivers/ardrone_interface/ardrone_interface.c +++ b/src/drivers/ardrone_interface/ardrone_interface.c @@ -89,8 +89,8 @@ static void usage(const char *reason) { if (reason) - fprintf(stderr, "%s\n", reason); - fprintf(stderr, "usage: ardrone_interface {start|stop|status} [-d <UART>]\n\n"); + warnx("%s\n", reason); + warnx("usage: {start|stop|status} [-d <UART>]\n\n"); exit(1); } @@ -110,7 +110,7 @@ int ardrone_interface_main(int argc, char *argv[]) if (!strcmp(argv[1], "start")) { if (thread_running) { - printf("ardrone_interface already running\n"); + warnx("already running\n"); /* this is not an error */ exit(0); } @@ -132,9 +132,9 @@ int ardrone_interface_main(int argc, char *argv[]) if (!strcmp(argv[1], "status")) { if (thread_running) { - printf("\tardrone_interface is running\n"); + warnx("running"); } else { - printf("\tardrone_interface not started\n"); + warnx("not started"); } exit(0); } @@ -158,7 +158,7 @@ static int ardrone_open_uart(char *uart_name, struct termios *uart_config_origin /* Back up the original uart configuration to restore it after exit */ if ((termios_state = tcgetattr(uart, uart_config_original)) < 0) { - fprintf(stderr, "[ardrone_interface] ERROR getting baudrate / termios config for %s: %d\n", uart_name, termios_state); + warnx("ERR: TCGETATTR %s: %d", uart_name, termios_state); close(uart); return -1; } @@ -171,14 +171,14 @@ static int ardrone_open_uart(char *uart_name, struct termios *uart_config_origin /* Set baud rate */ if (cfsetispeed(&uart_config, speed) < 0 || cfsetospeed(&uart_config, speed) < 0) { - fprintf(stderr, "[ardrone_interface] ERROR setting baudrate / termios config for %s: %d (cfsetispeed, cfsetospeed)\n", uart_name, termios_state); + warnx("ERR: cfsetispeed %s: %d", uart_name, termios_state); close(uart); return -1; } if ((termios_state = tcsetattr(uart, TCSANOW, &uart_config)) < 0) { - fprintf(stderr, "[ardrone_interface] ERROR setting baudrate / termios config for %s (tcsetattr)\n", uart_name); + warnx("ERR: tcsetattr: %s", uart_name); close(uart); return -1; } @@ -192,9 +192,6 @@ int ardrone_interface_thread_main(int argc, char *argv[]) char *device = "/dev/ttyS1"; - /* welcome user */ - printf("[ardrone_interface] Control started, taking over motors\n"); - /* File descriptors */ int gpios; @@ -237,7 +234,7 @@ int ardrone_interface_thread_main(int argc, char *argv[]) struct termios uart_config_original; if (motor_test_mode) { - printf("[ardrone_interface] Motor test mode enabled, setting 10 %% thrust.\n"); + warnx("setting 10 %% thrust.\n"); } /* Led animation */ @@ -255,9 +252,6 @@ int ardrone_interface_thread_main(int argc, char *argv[]) int actuator_controls_sub = orb_subscribe(ORB_ID_VEHICLE_ATTITUDE_CONTROLS); int armed_sub = orb_subscribe(ORB_ID(actuator_armed)); - printf("[ardrone_interface] Motors initialized - ready.\n"); - fflush(stdout); - /* enable UART, writes potentially an empty buffer, but multiplexing is disabled */ ardrone_write = ardrone_open_uart(device, &uart_config_original); @@ -265,7 +259,7 @@ int ardrone_interface_thread_main(int argc, char *argv[]) gpios = ar_multiplexing_init(); if (ardrone_write < 0) { - fprintf(stderr, "[ardrone_interface] Failed opening AR.Drone UART, exiting.\n"); + warnx("No UART, exiting."); thread_running = false; exit(ERROR); } @@ -273,7 +267,7 @@ int ardrone_interface_thread_main(int argc, char *argv[]) /* initialize motors */ if (OK != ar_init_motors(ardrone_write, gpios)) { close(ardrone_write); - fprintf(stderr, "[ardrone_interface] Failed initializing AR.Drone motors, exiting.\n"); + warnx("motor init fail"); thread_running = false; exit(ERROR); } @@ -294,7 +288,7 @@ int ardrone_interface_thread_main(int argc, char *argv[]) gpios = ar_multiplexing_init(); if (ardrone_write < 0) { - fprintf(stderr, "[ardrone_interface] Failed opening AR.Drone UART, exiting.\n"); + warnx("write fail"); thread_running = false; exit(ERROR); } @@ -302,7 +296,7 @@ int ardrone_interface_thread_main(int argc, char *argv[]) /* initialize motors */ if (OK != ar_init_motors(ardrone_write, gpios)) { close(ardrone_write); - fprintf(stderr, "[ardrone_interface] Failed initializing AR.Drone motors, exiting.\n"); + warnx("motor init fail"); thread_running = false; exit(ERROR); } @@ -378,11 +372,9 @@ int ardrone_interface_thread_main(int argc, char *argv[]) int termios_state; if ((termios_state = tcsetattr(ardrone_write, TCSANOW, &uart_config_original)) < 0) { - fprintf(stderr, "[ardrone_interface] ERROR setting baudrate / termios config for (tcsetattr)\n"); + warnx("ERR: tcsetattr"); } - printf("[ardrone_interface] Restored original UART config, exiting..\n"); - /* close uarts */ close(ardrone_write); ar_multiplexing_deinit(gpios); diff --git a/src/drivers/ardrone_interface/ardrone_motor_control.c b/src/drivers/ardrone_interface/ardrone_motor_control.c index fc017dd58..4fa24275f 100644 --- a/src/drivers/ardrone_interface/ardrone_motor_control.c +++ b/src/drivers/ardrone_interface/ardrone_motor_control.c @@ -301,7 +301,7 @@ int ar_init_motors(int ardrone_uart, int gpios) ardrone_write_motor_commands(ardrone_uart, 0, 0, 0, 0); if (errcounter != 0) { - fprintf(stderr, "[ardrone_interface] init sequence incomplete, failed %d times", -errcounter); + warnx("Failed %d times", -errcounter); fflush(stdout); } return errcounter; |