diff options
Diffstat (limited to 'src/drivers/drv_pwm_output.h')
| -rw-r--r-- | src/drivers/drv_pwm_output.h | 47 |
1 files changed, 45 insertions, 2 deletions
diff --git a/src/drivers/drv_pwm_output.h b/src/drivers/drv_pwm_output.h index 972573f9f..b10c3e18a 100644 --- a/src/drivers/drv_pwm_output.h +++ b/src/drivers/drv_pwm_output.h @@ -95,6 +95,11 @@ __BEGIN_DECLS #define PWM_LOWEST_MAX 1700 /** + * Do not output a channel with this value + */ +#define PWM_IGNORE_THIS_CHANNEL UINT16_MAX + +/** * Servo output signal type, value is actual servo output pulse * width in microseconds. */ @@ -112,6 +117,23 @@ struct pwm_output_values { unsigned channel_count; }; + +/** + * RC config values for a channel + * + * This allows for PX4IO_PAGE_RC_CONFIG values to be set without a + * param_get() dependency + */ +struct pwm_output_rc_config { + uint8_t channel; + uint16_t rc_min; + uint16_t rc_trim; + uint16_t rc_max; + uint16_t rc_dz; + uint16_t rc_assignment; + bool rc_reverse; +}; + /* * ORB tag for PWM outputs. */ @@ -160,7 +182,7 @@ ORB_DECLARE(output_pwm); #define DSM2_BIND_PULSES 3 /* DSM_BIND_START ioctl parameter, pulses required to start dsm2 pairing */ #define DSMX_BIND_PULSES 7 /* DSM_BIND_START ioctl parameter, pulses required to start dsmx pairing */ -#define DSMX8_BIND_PULSES 10 /* DSM_BIND_START ioctl parameter, pulses required to start 8 or more channel dsmx pairing */ +#define DSMX8_BIND_PULSES 9 /* DSM_BIND_START ioctl parameter, pulses required to start 8 or more channel dsmx pairing */ /** power up DSM receiver */ #define DSM_BIND_POWER_UP _IOC(_PWM_SERVO_BASE, 11) @@ -200,7 +222,28 @@ ORB_DECLARE(output_pwm); #define PWM_SERVO_GET_DISABLE_LOCKDOWN _IOC(_PWM_SERVO_BASE, 22) /** force safety switch off (to disable use of safety switch) */ -#define PWM_SERVO_SET_FORCE_SAFETY_OFF _IOC(_PWM_SERVO_BASE, 23) +#define PWM_SERVO_SET_FORCE_SAFETY_OFF _IOC(_PWM_SERVO_BASE, 23) + +/** force failsafe mode (failsafe values are set immediately even if failsafe condition not met) */ +#define PWM_SERVO_SET_FORCE_FAILSAFE _IOC(_PWM_SERVO_BASE, 24) + +/** make failsafe non-recoverable (termination) if it occurs */ +#define PWM_SERVO_SET_TERMINATION_FAILSAFE _IOC(_PWM_SERVO_BASE, 25) + +/** force safety switch on (to enable use of safety switch) */ +#define PWM_SERVO_SET_FORCE_SAFETY_ON _IOC(_PWM_SERVO_BASE, 26) + +/** set RC config for a channel. This takes a pointer to pwm_output_rc_config */ +#define PWM_SERVO_SET_RC_CONFIG _IOC(_PWM_SERVO_BASE, 27) + +/** set the 'OVERRIDE OK' bit, which allows for RC control on FMU loss */ +#define PWM_SERVO_SET_OVERRIDE_OK _IOC(_PWM_SERVO_BASE, 28) + +/** clear the 'OVERRIDE OK' bit, which allows for RC control on FMU loss */ +#define PWM_SERVO_CLEAR_OVERRIDE_OK _IOC(_PWM_SERVO_BASE, 29) + +/** setup OVERRIDE_IMMEDIATE behaviour on FMU fail */ +#define PWM_SERVO_SET_OVERRIDE_IMMEDIATE _IOC(_PWM_SERVO_BASE, 30) /* * |