diff options
Diffstat (limited to 'src/drivers/hott_telemetry/messages.h')
-rw-r--r-- | src/drivers/hott_telemetry/messages.h | 124 |
1 files changed, 124 insertions, 0 deletions
diff --git a/src/drivers/hott_telemetry/messages.h b/src/drivers/hott_telemetry/messages.h new file mode 100644 index 000000000..dd38075fa --- /dev/null +++ b/src/drivers/hott_telemetry/messages.h @@ -0,0 +1,124 @@ +/**************************************************************************** + * + * Copyright (c) 2012, 2013 PX4 Development Team. All rights reserved. + * Author: Simon Wilks <sjwilks@gmail.com> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file messages.h + * @author Simon Wilks <sjwilks@gmail.com> + * + * Graupner HoTT Telemetry message generation. + * + */ +#ifndef MESSAGES_H_ +#define MESSAGES_H + +#include <stdlib.h> + +/* The buffer size used to store messages. This must be at least as big as the number of + * fields in the largest message struct. + */ +#define MESSAGE_BUFFER_SIZE 50 + +/* The HoTT receiver demands a minimum 5ms period of silence after delivering its request. + * Note that the value specified here is lower than 5000 (5ms) as time is lost constucting + * the message after the read which takes some milliseconds. + */ +#define POST_READ_DELAY_IN_USECS 4000 +/* A pause of 3ms is required between each uint8_t sent back to the HoTT receiver. Much lower + * values can be used in practise though. + */ +#define POST_WRITE_DELAY_IN_USECS 2000 + +// Protocol constants. +#define BINARY_MODE_REQUEST_ID 0x80 // Binary mode request. +#define START_BYTE 0x7c +#define STOP_BYTE 0x7d +#define TEMP_ZERO_CELSIUS 0x14 + +/* Electric Air Module (EAM) constants. */ +#define ELECTRIC_AIR_MODULE 0x8e +#define EAM_SENSOR_ID 0xe0 + +/* The Electric Air Module message. */ +struct eam_module_msg { + uint8_t start; /**< Start byte */ + uint8_t eam_sensor_id; /**< EAM sensor ID */ + uint8_t warning; + uint8_t sensor_id; /**< Sensor ID, why different? */ + uint8_t alarm_inverse1; + uint8_t alarm_inverse2; + uint8_t cell1_L; /**< Lipo cell voltages. Not supported. */ + uint8_t cell2_L; + uint8_t cell3_L; + uint8_t cell4_L; + uint8_t cell5_L; + uint8_t cell6_L; + uint8_t cell7_L; + uint8_t cell1_H; + uint8_t cell2_H; + uint8_t cell3_H; + uint8_t cell4_H; + uint8_t cell5_H; + uint8_t cell6_H; + uint8_t cell7_H; + uint8_t batt1_voltage_L; /**< Battery 1 voltage, lower 8-bits in steps of 0.02V */ + uint8_t batt1_voltage_H; + uint8_t batt2_voltage_L; /**< Battery 2 voltage, lower 8-bits in steps of 0.02V */ + uint8_t batt2_voltage_H; + uint8_t temperature1; /**< Temperature sensor 1. 20 = 0 degrees */ + uint8_t temperature2; + uint8_t altitude_L; /**< Attitude (meters) lower 8-bits. 500 = 0 meters */ + uint8_t altitude_H; + uint8_t current_L; /**< Current (mAh) lower 8-bits in steps of 0.1V */ + uint8_t current_H; + uint8_t main_voltage_L; /**< Main power voltage lower 8-bits in steps of 0.1V */ + uint8_t main_voltage_H; + uint8_t battery_capacity_L; /**< Used battery capacity in steps of 10mAh */ + uint8_t battery_capacity_H; + uint8_t climbrate_L; /**< Climb rate in 0.01m/s. 0m/s = 30000 */ + uint8_t climbrate_H; + uint8_t climbrate_3s; /**< Climb rate in m/3sec. 0m/3sec = 120 */ + uint8_t rpm_L; /**< RPM Lower 8-bits In steps of 10 U/min */ + uint8_t rpm_H; + uint8_t electric_min; /**< Flight time in minutes. */ + uint8_t electric_sec; /**< Flight time in seconds. */ + uint8_t speed_L; /**< Airspeed in km/h in steps of 1 km/h */ + uint8_t speed_H; + uint8_t stop; /**< Stop byte */ + uint8_t checksum; /**< Lower 8-bits of all bytes summed. */ +}; + +void messages_init(void); +void build_eam_response(uint8_t *buffer, int *size); + +#endif /* MESSAGES_H_ */ |