diff options
Diffstat (limited to 'src/drivers/px4io/px4io.cpp')
-rw-r--r-- | src/drivers/px4io/px4io.cpp | 884 |
1 files changed, 620 insertions, 264 deletions
diff --git a/src/drivers/px4io/px4io.cpp b/src/drivers/px4io/px4io.cpp index fed83ea1a..c88abe59a 100644 --- a/src/drivers/px4io/px4io.cpp +++ b/src/drivers/px4io/px4io.cpp @@ -58,7 +58,6 @@ #include <arch/board/board.h> #include <drivers/device/device.h> -#include <drivers/device/i2c.h> #include <drivers/drv_rc_input.h> #include <drivers/drv_pwm_output.h> #include <drivers/drv_gpio.h> @@ -75,7 +74,9 @@ #include <uORB/topics/actuator_controls.h> #include <uORB/topics/actuator_controls_effective.h> #include <uORB/topics/actuator_outputs.h> -#include <uORB/topics/vehicle_status.h> +#include <uORB/topics/actuator_armed.h> +#include <uORB/topics/safety.h> +#include <uORB/topics/vehicle_control_mode.h> #include <uORB/topics/vehicle_command.h> #include <uORB/topics/rc_channels.h> #include <uORB/topics/battery_status.h> @@ -83,9 +84,13 @@ #include <debug.h> #include <mavlink/mavlink_log.h> -#include "uploader.h" #include <modules/px4iofirmware/protocol.h> +#include "uploader.h" + +extern device::Device *PX4IO_i2c_interface() weak_function; +extern device::Device *PX4IO_serial_interface() weak_function; + #define PX4IO_SET_DEBUG _IOC(0xff00, 0) #define PX4IO_INAIR_RESTART_ENABLE _IOC(0xff00, 1) @@ -94,7 +99,7 @@ * * Encapsulates PX4FMU to PX4IO communications modeled as file operations. */ -class PX4IO : public device::I2C +class PX4IO : public device::CDev { public: /** @@ -102,7 +107,8 @@ public: * * Initialize all class variables. */ - PX4IO(); + PX4IO(device::Device *interface); + /** * Destructor. * @@ -113,11 +119,18 @@ public: /** * Initialize the PX4IO class. * - * Initialize the physical I2C interface to PX4IO. Retrieve relevant initial system parameters. Initialize PX4IO registers. + * Retrieve relevant initial system parameters. Initialize PX4IO registers. */ virtual int init(); /** + * Detect if a PX4IO is connected. + * + * Only validate if there is a PX4IO to talk to. + */ + virtual int detect(); + + /** * IO Control handler. * * Handle all IOCTL calls to the PX4IO file descriptor. @@ -143,8 +156,8 @@ public: /** * Set the update rate for actuator outputs from FMU to IO. * - * @param[in] rate The rate in Hz actuator output are sent to IO. - * Min 10 Hz, max 400 Hz + * @param[in] rate The rate in Hz actuator outpus are sent to IO. + * Min 10 Hz, max 400 Hz */ int set_update_rate(int rate); @@ -159,12 +172,27 @@ public: /** * Push failsafe values to IO. * - * @param[in] vals Failsafe control inputs: in us PPM (900 for zero, 1500 for centered, 2100 for full) - * @param[in] len Number of channels, could up to 8 + * @param[in] vals Failsafe control inputs: in us PPM (900 for zero, 1500 for centered, 2100 for full) + * @param[in] len Number of channels, could up to 8 */ int set_failsafe_values(const uint16_t *vals, unsigned len); /** + * Set the minimum PWM signals when armed + */ + int set_min_values(const uint16_t *vals, unsigned len); + + /** + * Set the maximum PWM signal when armed + */ + int set_max_values(const uint16_t *vals, unsigned len); + + /** + * Set an idle PWM signal that is active right after startup, even when SAFETY_SAFE + */ + int set_idle_values(const uint16_t *vals, unsigned len); + + /** * Print IO status. * * Print all relevant IO status information @@ -172,6 +200,11 @@ public: void print_status(); /** + * Disable RC input handling + */ + int disable_rc_handling(); + + /** * Set the DSM VCC is controlled by relay one flag * * @param[in] enable true=DSM satellite VCC is controlled by relay1, false=DSM satellite VCC not controlled @@ -192,14 +225,18 @@ public: }; private: + device::Device *_interface; + // XXX + unsigned _hardware; ///< Hardware revision unsigned _max_actuators; ///<Maximum # of actuators supported by PX4IO unsigned _max_controls; ///<Maximum # of controls supported by PX4IO unsigned _max_rc_input; ///<Maximum receiver channels supported by PX4IO unsigned _max_relays; ///<Maximum relays supported by PX4IO unsigned _max_transfer; ///<Maximum number of I2C transfers supported by PX4IO - unsigned _update_interval; ///<Subscription interval limiting send rate + unsigned _update_interval; ///< Subscription interval limiting send rate + bool _rc_handling_disabled; ///< If set, IO does not evaluate, but only forward the RC values volatile int _task; ///<worker task id volatile bool _task_should_exit; ///<worker terminate flag @@ -213,16 +250,17 @@ private: uint16_t _alarms; ///<Various IO alarms /* subscribed topics */ - int _t_actuators; ///<actuator controls topic - int _t_armed; ///<system armed control topic - int _t_vstatus; ///<system / vehicle status - int _t_param; ///<parameter update topic + int _t_actuators; ///< actuator controls topic + int _t_actuator_armed; ///< system armed control topic + int _t_vehicle_control_mode;///< vehicle control mode topic + int _t_param; ///< parameter update topic /* advertised topics */ - orb_advert_t _to_input_rc; ///<rc inputs from IO topic - orb_advert_t _to_actuators_effective; ///<effective actuator controls topic - orb_advert_t _to_outputs; ///<mixed servo outputs topic - orb_advert_t _to_battery; ///<battery status / voltage topic + orb_advert_t _to_input_rc; ///< rc inputs from io + orb_advert_t _to_actuators_effective; ///< effective actuator controls topic + orb_advert_t _to_outputs; ///< mixed servo outputs topic + orb_advert_t _to_battery; ///< battery status / voltage + orb_advert_t _to_safety; ///< status of safety actuator_outputs_s _outputs; ///<mixed outputs actuator_controls_effective_s _controls_effective; ///<effective controls @@ -269,6 +307,11 @@ private: int io_get_status(); /** + * Disable RC input handling + */ + int io_disable_rc_handling(); + + /** * Fetch RC inputs from IO. * * @param input_rc Input structure to populate. @@ -298,7 +341,7 @@ private: * @param offset Register offset to start writing at. * @param values Pointer to array of values to write. * @param num_values The number of values to write. - * @return Zero if all values were successfully written. + * @return OK if all values were successfully written. */ int io_reg_set(uint8_t page, uint8_t offset, const uint16_t *values, unsigned num_values); @@ -308,7 +351,7 @@ private: * @param page Register page to write to. * @param offset Register offset to write to. * @param value Value to write. - * @return Zero if the value was written successfully. + * @return OK if the value was written successfully. */ int io_reg_set(uint8_t page, uint8_t offset, const uint16_t value); @@ -319,7 +362,7 @@ private: * @param offset Register offset to start reading from. * @param values Pointer to array where values should be stored. * @param num_values The number of values to read. - * @return Zero if all values were successfully read. + * @return OK if all values were successfully read. */ int io_reg_get(uint8_t page, uint8_t offset, uint16_t *values, unsigned num_values); @@ -376,14 +419,17 @@ PX4IO *g_dev; } -PX4IO::PX4IO() : - I2C("px4io", PX4IO_DEVICE_PATH, PX4_I2C_BUS_ONBOARD, PX4_I2C_OBDEV_PX4IO, 320000), +PX4IO::PX4IO(device::Device *interface) : + CDev("px4io", PX4IO_DEVICE_PATH), + _interface(interface), + _hardware(0), _max_actuators(0), _max_controls(0), _max_rc_input(0), _max_relays(0), _max_transfer(16), /* sensible default */ _update_interval(0), + _rc_handling_disabled(false), _task(-1), _task_should_exit(false), _mavlink_fd(-1), @@ -391,13 +437,14 @@ PX4IO::PX4IO() : _status(0), _alarms(0), _t_actuators(-1), - _t_armed(-1), - _t_vstatus(-1), + _t_actuator_armed(-1), + _t_vehicle_control_mode(-1), _t_param(-1), _to_input_rc(0), _to_actuators_effective(0), _to_outputs(0), _to_battery(0), + _to_safety(0), _primary_pwm_device(false), _battery_amp_per_volt(90.0f/5.0f), // this matches the 3DR current sensor _battery_amp_bias(0), @@ -429,42 +476,73 @@ PX4IO::~PX4IO() if (_task != -1) task_delete(_task); + if (_interface != nullptr) + delete _interface; + g_dev = nullptr; } int -PX4IO::init() +PX4IO::detect() { int ret; ASSERT(_task == -1); /* do regular cdev init */ - ret = I2C::init(); + ret = CDev::init(); if (ret != OK) return ret; - /* - * Enable a couple of retries for operations to IO. - * - * Register read/write operations are intentionally idempotent - * so this is safe as designed. - */ - _retries = 2; + /* get some parameters */ + unsigned protocol = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_PROTOCOL_VERSION); + if (protocol != PX4IO_PROTOCOL_VERSION) { + if (protocol == _io_reg_get_error) { + log("IO not installed"); + } else { + log("IO version error"); + mavlink_log_emergency(_mavlink_fd, "IO VERSION MISMATCH, PLEASE UPGRADE SOFTWARE!"); + } + + return -1; + } + log("IO found"); + + return 0; +} + +int +PX4IO::init() +{ + int ret; + + ASSERT(_task == -1); + + /* do regular cdev init */ + ret = CDev::init(); + if (ret != OK) + return ret; /* get some parameters */ + unsigned protocol = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_PROTOCOL_VERSION); + if (protocol != PX4IO_PROTOCOL_VERSION) { + log("protocol/firmware mismatch"); + mavlink_log_emergency(_mavlink_fd, "[IO] protocol/firmware mismatch, abort."); + return -1; + } + _hardware = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_HARDWARE_VERSION); _max_actuators = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_ACTUATOR_COUNT); - _max_controls = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_CONTROL_COUNT); + _max_controls = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_CONTROL_COUNT); _max_relays = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_RELAY_COUNT); _max_transfer = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_MAX_TRANSFER) - 2; _max_rc_input = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_RC_INPUT_COUNT); if ((_max_actuators < 1) || (_max_actuators > 255) || - (_max_relays < 1) || (_max_relays > 255) || - (_max_transfer < 16) || (_max_transfer > 255) || + (_max_relays > 32) || + (_max_transfer < 16) || (_max_transfer > 255) || (_max_rc_input < 1) || (_max_rc_input > 255)) { - log("failed getting parameters from PX4IO"); - mavlink_log_emergency(_mavlink_fd, "[IO] param read fail, abort."); + log("config read error"); + mavlink_log_emergency(_mavlink_fd, "[IO] config read fail, abort."); return -1; } if (_max_rc_input > RC_INPUT_MAX_CHANNELS) @@ -492,26 +570,27 @@ PX4IO::init() (reg & PX4IO_P_SETUP_ARMING_FMU_ARMED)) { mavlink_log_emergency(_mavlink_fd, "[IO] RECOVERING FROM FMU IN-AIR RESTART"); + log("INAIR RESTART RECOVERY (needs commander app running)"); /* WARNING: COMMANDER app/vehicle status must be initialized. * If this fails (or the app is not started), worst-case IO * remains untouched (so manual override is still available). */ - int vstatus_sub = orb_subscribe(ORB_ID(vehicle_status)); + int safety_sub = orb_subscribe(ORB_ID(actuator_armed)); /* fill with initial values, clear updated flag */ - vehicle_status_s status; + struct actuator_armed_s safety; uint64_t try_start_time = hrt_absolute_time(); bool updated = false; - /* keep checking for an update, ensure we got a recent state, + /* keep checking for an update, ensure we got a arming information, not something that was published a long time ago. */ do { - orb_check(vstatus_sub, &updated); + orb_check(safety_sub, &updated); if (updated) { /* got data, copy and exit loop */ - orb_copy(ORB_ID(vehicle_status), vstatus_sub, &status); + orb_copy(ORB_ID(actuator_armed), safety_sub, &safety); break; } @@ -519,7 +598,7 @@ PX4IO::init() usleep(10000); /* abort after 5s */ - if ((hrt_absolute_time() - try_start_time)/1000 > 50000) { + if ((hrt_absolute_time() - try_start_time)/1000 > 3000) { log("failed to recover from in-air restart (1), aborting IO driver init."); return 1; } @@ -537,35 +616,41 @@ PX4IO::init() cmd.param6 = 0; cmd.param7 = 0; cmd.command = VEHICLE_CMD_COMPONENT_ARM_DISARM; - cmd.target_system = status.system_id; - cmd.target_component = status.component_id; - cmd.source_system = status.system_id; - cmd.source_component = status.component_id; + // cmd.target_system = status.system_id; + // cmd.target_component = status.component_id; + // cmd.source_system = status.system_id; + // cmd.source_component = status.component_id; /* ask to confirm command */ cmd.confirmation = 1; /* send command once */ - (void)orb_advertise(ORB_ID(vehicle_command), &cmd); + orb_advert_t pub = orb_advertise(ORB_ID(vehicle_command), &cmd); /* spin here until IO's state has propagated into the system */ do { - orb_check(vstatus_sub, &updated); + orb_check(safety_sub, &updated); if (updated) { - orb_copy(ORB_ID(vehicle_status), vstatus_sub, &status); + orb_copy(ORB_ID(actuator_armed), safety_sub, &safety); } - /* wait 10 ms */ - usleep(10000); + /* wait 50 ms */ + usleep(50000); /* abort after 5s */ - if ((hrt_absolute_time() - try_start_time)/1000 > 50000) { + if ((hrt_absolute_time() - try_start_time)/1000 > 2000) { log("failed to recover from in-air restart (2), aborting IO driver init."); return 1; } - /* keep waiting for state change for 10 s */ - } while (!status.flag_system_armed); + /* re-send if necessary */ + if (!safety.armed) { + orb_publish(ORB_ID(vehicle_command), pub, &cmd); + log("re-sending arm cmd"); + } + + /* keep waiting for state change for 2 s */ + } while (!safety.armed); /* regular boot, no in-air restart, init IO */ } else { @@ -575,14 +660,19 @@ PX4IO::init() io_reg_modify(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_ARMING, PX4IO_P_SETUP_ARMING_FMU_ARMED | PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK | - PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK, 0); + PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK | + PX4IO_P_SETUP_ARMING_ALWAYS_PWM_ENABLE, 0); - /* publish RC config to IO */ - ret = io_set_rc_config(); - if (ret != OK) { - log("failed to update RC input config"); - mavlink_log_info(_mavlink_fd, "[IO] RC config upload fail"); - return ret; + if (_rc_handling_disabled) { + ret = io_disable_rc_handling(); + } else { + /* publish RC config to IO */ + ret = io_set_rc_config(); + if (ret != OK) { + log("failed to update RC input config"); + mavlink_log_info(_mavlink_fd, "[IO] RC config upload fail"); + return ret; + } } } @@ -596,7 +686,7 @@ PX4IO::init() } /* start the IO interface task */ - _task = task_create("px4io", SCHED_PRIORITY_ACTUATOR_OUTPUTS, 4096, (main_t)&PX4IO::task_main_trampoline, nullptr); + _task = task_create("px4io", SCHED_PRIORITY_ACTUATOR_OUTPUTS, 2048, (main_t)&PX4IO::task_main_trampoline, nullptr); if (_task < 0) { debug("task start failed: %d", errno); @@ -631,22 +721,30 @@ PX4IO::task_main() ORB_ID(actuator_controls_1)); orb_set_interval(_t_actuators, 20); /* default to 50Hz */ - _t_armed = orb_subscribe(ORB_ID(actuator_armed)); - orb_set_interval(_t_armed, 200); /* 5Hz update rate */ + _t_actuator_armed = orb_subscribe(ORB_ID(actuator_armed)); + orb_set_interval(_t_actuator_armed, 200); /* 5Hz update rate */ - _t_vstatus = orb_subscribe(ORB_ID(vehicle_status)); - orb_set_interval(_t_vstatus, 200); /* 5Hz update rate max. */ + _t_vehicle_control_mode = orb_subscribe(ORB_ID(vehicle_control_mode)); + orb_set_interval(_t_vehicle_control_mode, 200); /* 5Hz update rate max. */ _t_param = orb_subscribe(ORB_ID(parameter_update)); orb_set_interval(_t_param, 500); /* 2Hz update rate max. */ + if ((_t_actuators < 0) || + (_t_actuator_armed < 0) || + (_t_vehicle_control_mode < 0) || + (_t_param < 0)) { + log("subscription(s) failed"); + goto out; + } + /* poll descriptor */ pollfd fds[4]; fds[0].fd = _t_actuators; fds[0].events = POLLIN; - fds[1].fd = _t_armed; + fds[1].fd = _t_actuator_armed; fds[1].events = POLLIN; - fds[2].fd = _t_vstatus; + fds[2].fd = _t_vehicle_control_mode; fds[2].events = POLLIN; fds[3].fd = _t_param; fds[3].events = POLLIN; @@ -728,7 +826,7 @@ PX4IO::task_main() // See if bind parameter has been set, and reset it to 0 param_get(dsm_bind_param = param_find("RC_DSM_BIND"), &dsm_bind_val); if (dsm_bind_val) { - if (!(_status & PX4IO_P_STATUS_FLAGS_ARMED)) { + if (!(_status & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED)) { if ((dsm_bind_val == 1) || (dsm_bind_val == 2)) { mavlink_log_info(mavlink_fd, "[IO] binding dsm%c rx", dsm_bind_val == 1 ? '2' : 'x'); ioctl(nullptr, DSM_BIND_START, dsm_bind_val == 1 ? 3 : 7); @@ -755,6 +853,7 @@ PX4IO::task_main() unlock(); +out: debug("exiting"); /* clean up the alternate device node */ @@ -795,13 +894,52 @@ PX4IO::set_failsafe_values(const uint16_t *vals, unsigned len) } int +PX4IO::set_min_values(const uint16_t *vals, unsigned len) +{ + + if (len > _max_actuators) + /* fail with error */ + return E2BIG; + + /* copy values to registers in IO */ + return io_reg_set(PX4IO_PAGE_CONTROL_MIN_PWM, 0, vals, len); +} + +int +PX4IO::set_max_values(const uint16_t *vals, unsigned len) +{ + + if (len > _max_actuators) + /* fail with error */ + return E2BIG; + + /* copy values to registers in IO */ + return io_reg_set(PX4IO_PAGE_CONTROL_MAX_PWM, 0, vals, len); +} + +int +PX4IO::set_idle_values(const uint16_t *vals, unsigned len) +{ + + if (len > _max_actuators) + /* fail with error */ + return E2BIG; + + printf("Sending IDLE values\n"); + + /* copy values to registers in IO */ + return io_reg_set(PX4IO_PAGE_IDLE_PWM, 0, vals, len); +} + + +int PX4IO::io_set_arming_state() { actuator_armed_s armed; ///< system armed state - vehicle_status_s vstatus; ///< overall system state + vehicle_control_mode_s control_mode; ///< vehicle_control_mode - orb_copy(ORB_ID(actuator_armed), _t_armed, &armed); - orb_copy(ORB_ID(vehicle_status), _t_vstatus, &vstatus); + orb_copy(ORB_ID(actuator_armed), _t_actuator_armed, &armed); + orb_copy(ORB_ID(vehicle_control_mode), _t_vehicle_control_mode, &control_mode); uint16_t set = 0; uint16_t clear = 0; @@ -811,14 +949,13 @@ PX4IO::io_set_arming_state() } else { clear |= PX4IO_P_SETUP_ARMING_FMU_ARMED; } - if (armed.ready_to_arm) { set |= PX4IO_P_SETUP_ARMING_IO_ARM_OK; } else { clear |= PX4IO_P_SETUP_ARMING_IO_ARM_OK; } - if (vstatus.flag_external_manual_override_ok) { + if (control_mode.flag_external_manual_override_ok) { set |= PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK; } else { clear |= PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK; @@ -828,6 +965,21 @@ PX4IO::io_set_arming_state() } int +PX4IO::disable_rc_handling() +{ + return io_disable_rc_handling(); +} + +int +PX4IO::io_disable_rc_handling() +{ + uint16_t set = PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED; + uint16_t clear = 0; + + return io_reg_modify(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_ARMING, clear, set); +} + +int PX4IO::io_set_rc_config() { unsigned offset = 0; @@ -945,14 +1097,14 @@ PX4IO::io_handle_status(uint16_t status) */ /* check for IO reset - force it back to armed if necessary */ - if (_status & PX4IO_P_STATUS_FLAGS_ARMED && !(status & PX4IO_P_STATUS_FLAGS_ARMED) + if (_status & PX4IO_P_STATUS_FLAGS_SAFETY_OFF && !(status & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) && !(status & PX4IO_P_STATUS_FLAGS_ARM_SYNC)) { /* set the arming flag */ - ret = io_reg_modify(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FLAGS, 0, PX4IO_P_STATUS_FLAGS_ARMED | PX4IO_P_STATUS_FLAGS_ARM_SYNC); + ret = io_reg_modify(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FLAGS, 0, PX4IO_P_STATUS_FLAGS_SAFETY_OFF | PX4IO_P_STATUS_FLAGS_ARM_SYNC); /* set new status */ _status = status; - _status &= PX4IO_P_STATUS_FLAGS_ARMED; + _status &= PX4IO_P_STATUS_FLAGS_SAFETY_OFF; } else if (!(_status & PX4IO_P_STATUS_FLAGS_ARM_SYNC)) { /* set the sync flag */ @@ -967,6 +1119,27 @@ PX4IO::io_handle_status(uint16_t status) _status = status; } + /** + * Get and handle the safety status + */ + struct safety_s safety; + safety.timestamp = hrt_absolute_time(); + + if (status & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) { + safety.safety_off = true; + safety.safety_switch_available = true; + } else { + safety.safety_off = false; + safety.safety_switch_available = true; + } + + /* lazily publish the safety status */ + if (_to_safety > 0) { + orb_publish(ORB_ID(safety), _to_safety, &safety); + } else { + _to_safety = orb_advertise(ORB_ID(safety), &safety); + } + return ret; } @@ -996,7 +1169,7 @@ PX4IO::io_get_status() io_handle_status(regs[0]); io_handle_alarms(regs[1]); - + /* only publish if battery has a valid minimum voltage */ if (regs[2] > 3300) { battery_status_s battery_status; @@ -1030,6 +1203,7 @@ PX4IO::io_get_status() _to_battery = orb_advertise(ORB_ID(battery_status), &battery_status); } } + return ret; } @@ -1037,38 +1211,38 @@ int PX4IO::io_get_raw_rc_input(rc_input_values &input_rc) { uint32_t channel_count; - int ret = OK; + int ret; /* we don't have the status bits, so input_source has to be set elsewhere */ input_rc.input_source = RC_INPUT_SOURCE_UNKNOWN; + static const unsigned prolog = (PX4IO_P_RAW_RC_BASE - PX4IO_P_RAW_RC_COUNT); + uint16_t regs[RC_INPUT_MAX_CHANNELS + prolog]; + /* - * XXX Because the channel count and channel data are fetched - * separately, there is a risk of a race between the two - * that could leave us with channel data and a count that - * are out of sync. - * Fixing this would require a guarantee of atomicity from - * IO, and a single fetch for both count and channels. - * - * XXX Since IO has the input calibration info, we ought to be - * able to get the pre-fixed-up controls directly. + * Read the channel count and the first 9 channels. * - * XXX can we do this more cheaply? If we knew we had DMA, it would - * almost certainly be better to just get all the inputs... + * This should be the common case (9 channel R/C control being a reasonable upper bound). */ - channel_count = io_reg_get(PX4IO_PAGE_RAW_RC_INPUT, PX4IO_P_RAW_RC_COUNT); - if (channel_count == _io_reg_get_error) - return -EIO; - if (channel_count > RC_INPUT_MAX_CHANNELS) - channel_count = RC_INPUT_MAX_CHANNELS; - input_rc.channel_count = channel_count; + input_rc.timestamp = hrt_absolute_time(); + ret = io_reg_get(PX4IO_PAGE_RAW_RC_INPUT, PX4IO_P_RAW_RC_COUNT, ®s[0], prolog + 9); + if (ret != OK) + return ret; - if (channel_count > 0) { - ret = io_reg_get(PX4IO_PAGE_RAW_RC_INPUT, PX4IO_P_RAW_RC_BASE, input_rc.values, channel_count); - if (ret == OK) - input_rc.timestamp = hrt_absolute_time(); + /* + * Get the channel count any any extra channels. This is no more expensive than reading the + * channel count once. + */ + channel_count = regs[0]; + if (channel_count > 9) { + ret = io_reg_get(PX4IO_PAGE_RAW_RC_INPUT, PX4IO_P_RAW_RC_BASE + 9, ®s[prolog + 9], channel_count - 9); + if (ret != OK) + return ret; } + input_rc.channel_count = channel_count; + memcpy(input_rc.values, ®s[prolog], channel_count * 2); + return ret; } @@ -1198,25 +1372,12 @@ PX4IO::io_reg_set(uint8_t page, uint8_t offset, const uint16_t *values, unsigned return -EINVAL; } - /* set up the transfer */ - uint8_t addr[2] = { - page, - offset - }; - i2c_msg_s msgv[2]; - - msgv[0].flags = 0; - msgv[0].buffer = addr; - msgv[0].length = 2; - msgv[1].flags = I2C_M_NORESTART; - msgv[1].buffer = (uint8_t *)values; - msgv[1].length = num_values * sizeof(*values); - - /* perform the transfer */ - int ret = transfer(msgv, 2); - if (ret != OK) - debug("io_reg_set: error %d", ret); - return ret; + int ret = _interface->write((page << 8) | offset, (void *)values, num_values); + if (ret != (int)num_values) { + debug("io_reg_set(%u,%u,%u): error %d", page, offset, num_values, ret); + return -1; + } + return OK; } int @@ -1228,25 +1389,18 @@ PX4IO::io_reg_set(uint8_t page, uint8_t offset, uint16_t value) int PX4IO::io_reg_get(uint8_t page, uint8_t offset, uint16_t *values, unsigned num_values) { - /* set up the transfer */ - uint8_t addr[2] = { - page, - offset - }; - i2c_msg_s msgv[2]; - - msgv[0].flags = 0; - msgv[0].buffer = addr; - msgv[0].length = 2; - msgv[1].flags = I2C_M_READ; - msgv[1].buffer = (uint8_t *)values; - msgv[1].length = num_values * sizeof(*values); + /* range check the transfer */ + if (num_values > ((_max_transfer) / sizeof(*values))) { + debug("io_reg_get: too many registers (%u, max %u)", num_values, _max_transfer / 2); + return -EINVAL; + } - /* perform the transfer */ - int ret = transfer(msgv, 2); - if (ret != OK) - debug("io_reg_get: data error %d", ret); - return ret; + int ret = _interface->read((page << 8) | offset, reinterpret_cast<void *>(values), num_values); + if (ret != (int)num_values) { + debug("io_reg_get(%u,%u,%u): data error %d", page, offset, num_values, ret); + return -1; + } + return OK; } uint32_t @@ -1254,7 +1408,7 @@ PX4IO::io_reg_get(uint8_t page, uint8_t offset) { uint16_t value; - if (io_reg_get(page, offset, &value, 1)) + if (io_reg_get(page, offset, &value, 1) != OK) return _io_reg_get_error; return value; @@ -1267,7 +1421,7 @@ PX4IO::io_reg_modify(uint8_t page, uint8_t offset, uint16_t clearbits, uint16_t uint16_t value; ret = io_reg_get(page, offset, &value, 1); - if (ret) + if (ret != OK) return ret; value &= ~clearbits; value |= setbits; @@ -1339,9 +1493,9 @@ void PX4IO::print_status() { /* basic configuration */ - printf("protocol %u software %u bootloader %u buffer %uB\n", + printf("protocol %u hardware %u bootloader %u buffer %uB\n", io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_PROTOCOL_VERSION), - io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_SOFTWARE_VERSION), + io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_HARDWARE_VERSION), io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_BOOTLOADER_VERSION), io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_MAX_TRANSFER)); printf("%u controls %u actuators %u R/C inputs %u analog inputs %u relays\n", @@ -1357,7 +1511,8 @@ PX4IO::print_status() uint16_t flags = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_FLAGS); printf("status 0x%04x%s%s%s%s%s%s%s%s%s%s%s%s%s\n", flags, - ((flags & PX4IO_P_STATUS_FLAGS_ARMED) ? " ARMED" : ""), + ((flags & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED) ? " OUTPUTS_ARMED" : ""), + ((flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) ? " SAFETY_OFF" : " SAFETY_SAFE"), ((flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) ? " OVERRIDE" : ""), ((flags & PX4IO_P_STATUS_FLAGS_RC_OK) ? " RC_OK" : " RC_FAIL"), ((flags & PX4IO_P_STATUS_FLAGS_RC_PPM) ? " PPM" : ""), @@ -1365,13 +1520,13 @@ PX4IO::print_status() (((flags & PX4IO_P_STATUS_FLAGS_RC_DSM) && (flags & PX4IO_P_STATUS_FLAGS_RC_DSM11)) ? " DSM11" : ""), ((flags & PX4IO_P_STATUS_FLAGS_RC_SBUS) ? " SBUS" : ""), ((flags & PX4IO_P_STATUS_FLAGS_FMU_OK) ? " FMU_OK" : " FMU_FAIL"), - ((flags & PX4IO_P_STATUS_FLAGS_RAW_PWM) ? " RAW_PPM" : ""), + ((flags & PX4IO_P_STATUS_FLAGS_RAW_PWM) ? " RAW_PWM_PASSTHROUGH" : ""), ((flags & PX4IO_P_STATUS_FLAGS_MIXER_OK) ? " MIXER_OK" : " MIXER_FAIL"), ((flags & PX4IO_P_STATUS_FLAGS_ARM_SYNC) ? " ARM_SYNC" : " ARM_NO_SYNC"), ((flags & PX4IO_P_STATUS_FLAGS_INIT_OK) ? " INIT_OK" : " INIT_FAIL"), ((flags & PX4IO_P_STATUS_FLAGS_FAILSAFE) ? " FAILSAFE" : "")); uint16_t alarms = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_ALARMS); - printf("alarms 0x%04x%s%s%s%s%s%s%s\n", + printf("alarms 0x%04x%s%s%s%s%s%s%s%s\n", alarms, ((alarms & PX4IO_P_STATUS_ALARMS_VBATT_LOW) ? " VBATT_LOW" : ""), ((alarms & PX4IO_P_STATUS_ALARMS_TEMPERATURE) ? " TEMPERATURE" : ""), @@ -1379,18 +1534,26 @@ PX4IO::print_status() ((alarms & PX4IO_P_STATUS_ALARMS_ACC_CURRENT) ? " ACC_CURRENT" : ""), ((alarms & PX4IO_P_STATUS_ALARMS_FMU_LOST) ? " FMU_LOST" : ""), ((alarms & PX4IO_P_STATUS_ALARMS_RC_LOST) ? " RC_LOST" : ""), - ((alarms & PX4IO_P_STATUS_ALARMS_PWM_ERROR) ? " PWM_ERROR" : "")); + ((alarms & PX4IO_P_STATUS_ALARMS_PWM_ERROR) ? " PWM_ERROR" : ""), + ((alarms & PX4IO_P_STATUS_ALARMS_VSERVO_FAULT) ? " VSERVO_FAULT" : "")); /* now clear alarms */ io_reg_set(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_ALARMS, 0xFFFF); - printf("vbatt %u ibatt %u vbatt scale %u\n", - io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_VBATT), - io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_IBATT), - io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_VBATT_SCALE)); - printf("amp_per_volt %.3f amp_offset %.3f mAh discharged %.3f\n", - (double)_battery_amp_per_volt, - (double)_battery_amp_bias, - (double)_battery_mamphour_total); + if (_hardware == 1) { + printf("vbatt mV %u ibatt mV %u vbatt scale %u\n", + io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_VBATT), + io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_IBATT), + io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_VBATT_SCALE)); + printf("amp_per_volt %.3f amp_offset %.3f mAh discharged %.3f\n", + (double)_battery_amp_per_volt, + (double)_battery_amp_bias, + (double)_battery_mamphour_total); + } else if (_hardware == 2) { + printf("vservo %u mV vservo scale %u\n", + io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_VSERVO), + io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_VSERVO_SCALE)); + printf("vrssi %u\n", io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_VRSSI)); + } printf("actuators"); for (unsigned i = 0; i < _max_actuators; i++) printf(" %u", io_reg_get(PX4IO_PAGE_ACTUATORS, i)); @@ -1420,12 +1583,14 @@ PX4IO::print_status() /* setup and state */ printf("features 0x%04x\n", io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_FEATURES)); uint16_t arming = io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_ARMING); - printf("arming 0x%04x%s%s%s%s\n", + printf("arming 0x%04x%s%s%s%s%s%s\n", arming, - ((arming & PX4IO_P_SETUP_ARMING_FMU_ARMED) ? " FMU_ARMED" : ""), - ((arming & PX4IO_P_SETUP_ARMING_IO_ARM_OK) ? " IO_ARM_OK" : ""), + ((arming & PX4IO_P_SETUP_ARMING_FMU_ARMED) ? " FMU_ARMED" : " FMU_DISARMED"), + ((arming & PX4IO_P_SETUP_ARMING_IO_ARM_OK) ? " IO_ARM_OK" : " IO_ARM_DENIED"), ((arming & PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK) ? " MANUAL_OVERRIDE_OK" : ""), - ((arming & PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK) ? " INAIR_RESTART_OK" : "")); + ((arming & PX4IO_P_SETUP_ARMING_FAILSAFE_CUSTOM) ? " FAILSAFE_CUSTOM" : ""), + ((arming & PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK) ? " INAIR_RESTART_OK" : ""), + ((arming & PX4IO_P_SETUP_ARMING_ALWAYS_PWM_ENABLE) ? " ALWAYS_PWM_ENABLE" : "")); printf("rates 0x%04x default %u alt %u relays 0x%04x\n", io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_PWM_RATES), io_reg_get(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_PWM_DEFAULTRATE), @@ -1453,6 +1618,9 @@ PX4IO::print_status() printf("failsafe"); for (unsigned i = 0; i < _max_actuators; i++) printf(" %u", io_reg_get(PX4IO_PAGE_FAILSAFE_PWM, i)); + printf("\nidle values"); + for (unsigned i = 0; i < _max_actuators; i++) + printf(" %u", io_reg_get(PX4IO_PAGE_IDLE_PWM, i)); printf("\n"); } @@ -1561,9 +1729,9 @@ PX4IO::ioctl(file * /*filep*/, int cmd, unsigned long arg) unsigned channel = cmd - PWM_SERVO_GET_RATEGROUP(0); - uint32_t value = io_reg_get(PX4IO_PAGE_PWM_INFO, PX4IO_RATE_MAP_BASE + channel); - - *(uint32_t *)arg = value; + *(uint32_t *)arg = io_reg_get(PX4IO_PAGE_PWM_INFO, PX4IO_RATE_MAP_BASE + channel); + if (*(uint32_t *)arg == _io_reg_get_error) + ret = -EIO; break; } @@ -1571,7 +1739,7 @@ PX4IO::ioctl(file * /*filep*/, int cmd, unsigned long arg) uint32_t bits = (1 << _max_relays) - 1; /* don't touch relay1 if it's controlling RX vcc */ if (_dsm_vcc_ctl) - bits &= ~PX4IO_RELAY1; + bits &= ~PX4IO_P_SETUP_RELAYS_POWER1; ret = io_reg_modify(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_RELAYS, bits, 0); break; } @@ -1579,7 +1747,7 @@ PX4IO::ioctl(file * /*filep*/, int cmd, unsigned long arg) case GPIO_SET: arg &= ((1 << _max_relays) - 1); /* don't touch relay1 if it's controlling RX vcc */ - if (_dsm_vcc_ctl & (arg & PX4IO_RELAY1)) + if (_dsm_vcc_ctl & (arg & PX4IO_P_SETUP_RELAYS_POWER1)) ret = -EINVAL; else ret = io_reg_modify(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_RELAYS, 0, arg); @@ -1588,7 +1756,7 @@ PX4IO::ioctl(file * /*filep*/, int cmd, unsigned long arg) case GPIO_CLEAR: arg &= ((1 << _max_relays) - 1); /* don't touch relay1 if it's controlling RX vcc */ - if (_dsm_vcc_ctl & (arg & PX4IO_RELAY1)) + if (_dsm_vcc_ctl & (arg & PX4IO_P_SETUP_RELAYS_POWER1)) ret = -EINVAL; else ret = io_reg_modify(PX4IO_PAGE_SETUP, PX4IO_P_SETUP_RELAYS, arg, 0); @@ -1686,8 +1854,8 @@ int PX4IO::set_update_rate(int rate) { int interval_ms = 1000 / rate; - if (interval_ms < 5) { - interval_ms = 5; + if (interval_ms < 3) { + interval_ms = 3; warnx("update rate too high, limiting interval to %d ms (%d Hz).", interval_ms, 1000 / interval_ms); } @@ -1712,23 +1880,69 @@ extern "C" __EXPORT int px4io_main(int argc, char *argv[]); namespace { +device::Device * +get_interface() +{ + device::Device *interface = nullptr; + +#ifndef CONFIG_ARCH_BOARD_PX4FMU_V1 + /* try for a serial interface */ + if (PX4IO_serial_interface != nullptr) + interface = PX4IO_serial_interface(); + if (interface != nullptr) + goto got; +#endif + + /* try for an I2C interface if we haven't got a serial one */ + if (PX4IO_i2c_interface != nullptr) + interface = PX4IO_i2c_interface(); + if (interface != nullptr) + goto got; + + errx(1, "cannot alloc interface"); + +got: + if (interface->init() != OK) { + delete interface; + errx(1, "interface init failed"); + } + + return interface; +} + void start(int argc, char *argv[]) { if (g_dev != nullptr) errx(1, "already loaded"); + /* allocate the interface */ + device::Device *interface = get_interface(); + /* create the driver - it will set g_dev */ - (void)new PX4IO(); + (void)new PX4IO(interface); if (g_dev == nullptr) errx(1, "driver alloc failed"); if (OK != g_dev->init()) { delete g_dev; + g_dev = nullptr; errx(1, "driver init failed"); } + /* disable RC handling on request */ + if (argc > 1) { + if (!strcmp(argv[1], "norc")) { + + if(g_dev->disable_rc_handling()) + warnx("Failed disabling RC handling"); + + } else { + warnx("unknown argument: %s", argv[1]); + } + } + int dsm_vcc_ctl; if (param_get(param_find("RC_RL1_DSM_VCC"), &dsm_vcc_ctl) == OK) { @@ -1741,6 +1955,34 @@ start(int argc, char *argv[]) } void +detect(int argc, char *argv[]) +{ + if (g_dev != nullptr) + errx(0, "already loaded"); + + /* allocate the interface */ + device::Device *interface = get_interface(); + + /* create the driver - it will set g_dev */ + (void)new PX4IO(interface); + + if (g_dev == nullptr) + errx(1, "driver alloc failed"); + + int ret = g_dev->detect(); + + delete g_dev; + g_dev = nullptr; + + if (ret) { + /* nonzero, error */ + exit(1); + } else { + exit(0); + } +} + +void bind(int argc, char *argv[]) { int pulses; @@ -1786,6 +2028,11 @@ test(void) if (ioctl(fd, PWM_SERVO_GET_COUNT, (unsigned long)&servo_count)) err(1, "failed to get servo count"); + /* tell IO that its ok to disable its safety with the switch */ + ret = ioctl(fd, PWM_SERVO_SET_ARM_OK, 0); + if (ret != OK) + err(1, "PWM_SERVO_SET_ARM_OK"); + if (ioctl(fd, PWM_SERVO_ARM, 0)) err(1, "failed to arm servos"); @@ -1834,7 +2081,7 @@ test(void) /* Check if user wants to quit */ char c; if (read(console, &c, 1) == 1) { - if (c == 0x03 || c == 0x63) { + if (c == 0x03 || c == 0x63 || c == 'q') { warnx("User abort\n"); close(console); exit(0); @@ -1871,8 +2118,19 @@ monitor(void) } } +void +if_test(unsigned mode) +{ + device::Device *interface = get_interface(); + + int result = interface->ioctl(1, mode); /* XXX magic numbers */ + delete interface; + + errx(0, "test returned %d", result); } +} /* namespace */ + int px4io_main(int argc, char *argv[]) { @@ -1883,28 +2141,90 @@ px4io_main(int argc, char *argv[]) if (!strcmp(argv[1], "start")) start(argc - 1, argv + 1); - if (!strcmp(argv[1], "limit")) { + if (!strcmp(argv[1], "detect")) + detect(argc - 1, argv + 1); + + if (!strcmp(argv[1], "update")) { if (g_dev != nullptr) { + printf("[px4io] loaded, detaching first\n"); + /* stop the driver */ + delete g_dev; + } - if ((argc > 2)) { - g_dev->set_update_rate(atoi(argv[2])); - } else { - errx(1, "missing argument (50 - 200 Hz)"); - return 1; - } + PX4IO_Uploader *up; + const char *fn[5]; + + /* work out what we're uploading... */ + if (argc > 2) { + fn[0] = argv[2]; + fn[1] = nullptr; + + } else { + fn[0] = "/etc/extras/px4io-v2_default.bin"; + fn[1] = "/etc/extras/px4io-v1_default.bin"; + fn[2] = "/fs/microsd/px4io.bin"; + fn[3] = "/fs/microsd/px4io2.bin"; + fn[4] = nullptr; + } + + up = new PX4IO_Uploader; + int ret = up->upload(&fn[0]); + delete up; + + switch (ret) { + case OK: + break; + + case -ENOENT: + errx(1, "PX4IO firmware file not found"); + + case -EEXIST: + case -EIO: + errx(1, "error updating PX4IO - check that bootloader mode is enabled"); + + case -EINVAL: + errx(1, "verify failed - retry the update"); + + case -ETIMEDOUT: + errx(1, "timed out waiting for bootloader - power-cycle and try again"); + + default: + errx(1, "unexpected error %d", ret); + } + + return ret; + } + + if (!strcmp(argv[1], "iftest")) { + if (g_dev != nullptr) + errx(1, "can't iftest when started"); + + if_test((argc > 2) ? strtol(argv[2], NULL, 0) : 0); + } + + /* commands below here require a started driver */ + + if (g_dev == nullptr) + errx(1, "not started"); + + if (!strcmp(argv[1], "limit")) { + + if ((argc > 2)) { + g_dev->set_update_rate(atoi(argv[2])); + } else { + errx(1, "missing argument (50 - 400 Hz)"); + return 1; } exit(0); } if (!strcmp(argv[1], "current")) { - if (g_dev != nullptr) { - if ((argc > 3)) { - g_dev->set_battery_current_scaling(atof(argv[2]), atof(argv[3])); - } else { - errx(1, "missing argument (apm_per_volt, amp_offset)"); - return 1; - } + if ((argc > 3)) { + g_dev->set_battery_current_scaling(atof(argv[2]), atof(argv[3])); + } else { + errx(1, "missing argument (apm_per_volt, amp_offset)"); + return 1; } exit(0); } @@ -1915,70 +2235,158 @@ px4io_main(int argc, char *argv[]) errx(1, "failsafe command needs at least one channel value (ppm)"); } + /* set values for first 8 channels, fill unassigned channels with 1500. */ + uint16_t failsafe[8]; + + for (unsigned i = 0; i < sizeof(failsafe) / sizeof(failsafe[0]); i++) { + + /* set channel to commandline argument or to 900 for non-provided channels */ + if (argc > i + 2) { + failsafe[i] = atoi(argv[i+2]); + if (failsafe[i] < 800 || failsafe[i] > 2200) { + errx(1, "value out of range of 800 < value < 2200. Aborting."); + } + } else { + /* a zero value will result in stopping to output any pulse */ + failsafe[i] = 0; + } + } + + int ret = g_dev->set_failsafe_values(failsafe, sizeof(failsafe) / sizeof(failsafe[0])); + + if (ret != OK) + errx(ret, "failed setting failsafe values"); + exit(0); + } + + if (!strcmp(argv[1], "min")) { + + if (argc < 3) { + errx(1, "min command needs at least one channel value (PWM)"); + } + if (g_dev != nullptr) { - /* set values for first 8 channels, fill unassigned channels with 1500. */ - uint16_t failsafe[8]; + /* set values for first 8 channels, fill unassigned channels with 900. */ + uint16_t min[8]; - for (int i = 0; i < sizeof(failsafe) / sizeof(failsafe[0]); i++) + for (unsigned i = 0; i < sizeof(min) / sizeof(min[0]); i++) { /* set channel to commanline argument or to 900 for non-provided channels */ if (argc > i + 2) { - failsafe[i] = atoi(argv[i+2]); - if (failsafe[i] < 800 || failsafe[i] > 2200) { - errx(1, "value out of range of 800 < value < 2200. Aborting."); + min[i] = atoi(argv[i+2]); + if (min[i] < 900 || min[i] > 1200) { + errx(1, "value out of range of 900 < value < 1200. Aborting."); } } else { - /* a zero value will result in stopping to output any pulse */ - failsafe[i] = 0; + /* a zero value will the default */ + min[i] = 0; } } - int ret = g_dev->set_failsafe_values(failsafe, sizeof(failsafe) / sizeof(failsafe[0])); + int ret = g_dev->set_min_values(min, sizeof(min) / sizeof(min[0])); if (ret != OK) - errx(ret, "failed setting failsafe values"); + errx(ret, "failed setting min values"); } else { errx(1, "not loaded"); } exit(0); } - if (!strcmp(argv[1], "recovery")) { + if (!strcmp(argv[1], "max")) { + + if (argc < 3) { + errx(1, "max command needs at least one channel value (PWM)"); + } if (g_dev != nullptr) { - /* - * Enable in-air restart support. - * We can cheat and call the driver directly, as it - * doesn't reference filp in ioctl() - */ - g_dev->ioctl(nullptr, PX4IO_INAIR_RESTART_ENABLE, 1); + + /* set values for first 8 channels, fill unassigned channels with 2100. */ + uint16_t max[8]; + + for (unsigned i = 0; i < sizeof(max) / sizeof(max[0]); i++) + { + /* set channel to commanline argument or to 2100 for non-provided channels */ + if (argc > i + 2) { + max[i] = atoi(argv[i+2]); + if (max[i] < 1800 || max[i] > 2100) { + errx(1, "value out of range of 1800 < value < 2100. Aborting."); + } + } else { + /* a zero value will the default */ + max[i] = 0; + } + } + + int ret = g_dev->set_max_values(max, sizeof(max) / sizeof(max[0])); + + if (ret != OK) + errx(ret, "failed setting max values"); } else { errx(1, "not loaded"); } exit(0); } - if (!strcmp(argv[1], "stop")) { + if (!strcmp(argv[1], "idle")) { + + if (argc < 3) { + errx(1, "max command needs at least one channel value (PWM)"); + } if (g_dev != nullptr) { - /* stop the driver */ - delete g_dev; + + /* set values for first 8 channels, fill unassigned channels with 0. */ + uint16_t idle[8]; + + for (unsigned i = 0; i < sizeof(idle) / sizeof(idle[0]); i++) + { + /* set channel to commanline argument or to 0 for non-provided channels */ + if (argc > i + 2) { + idle[i] = atoi(argv[i+2]); + if (idle[i] < 900 || idle[i] > 2100) { + errx(1, "value out of range of 900 < value < 2100. Aborting."); + } + } else { + /* a zero value will the default */ + idle[i] = 0; + } + } + + int ret = g_dev->set_idle_values(idle, sizeof(idle) / sizeof(idle[0])); + + if (ret != OK) + errx(ret, "failed setting idle values"); } else { errx(1, "not loaded"); } exit(0); } + if (!strcmp(argv[1], "recovery")) { + + /* + * Enable in-air restart support. + * We can cheat and call the driver directly, as it + * doesn't reference filp in ioctl() + */ + g_dev->ioctl(NULL, PX4IO_INAIR_RESTART_ENABLE, 1); + exit(0); + } + + if (!strcmp(argv[1], "stop")) { + + /* stop the driver */ + delete g_dev; + exit(0); + } + if (!strcmp(argv[1], "status")) { - if (g_dev != nullptr) { - printf("[px4io] loaded\n"); - g_dev->print_status(); - } else { - printf("[px4io] not loaded\n"); - } + printf("[px4io] loaded\n"); + g_dev->print_status(); exit(0); } @@ -2005,58 +2413,6 @@ px4io_main(int argc, char *argv[]) exit(0); } - /* note, stop not currently implemented */ - - if (!strcmp(argv[1], "update")) { - - if (g_dev != nullptr) { - printf("[px4io] loaded, detaching first\n"); - /* stop the driver */ - delete g_dev; - } - - PX4IO_Uploader *up; - const char *fn[3]; - - /* work out what we're uploading... */ - if (argc > 2) { - fn[0] = argv[2]; - fn[1] = nullptr; - - } else { - fn[0] = "/fs/microsd/px4io.bin"; - fn[1] = "/etc/px4io.bin"; - fn[2] = nullptr; - } - - up = new PX4IO_Uploader; - int ret = up->upload(&fn[0]); - delete up; - - switch (ret) { - case OK: - break; - - case -ENOENT: - errx(1, "PX4IO firmware file not found"); - - case -EEXIST: - case -EIO: - errx(1, "error updating PX4IO - check that bootloader mode is enabled"); - - case -EINVAL: - errx(1, "verify failed - retry the update"); - - case -ETIMEDOUT: - errx(1, "timed out waiting for bootloader - power-cycle and try again"); - - default: - errx(1, "unexpected error %d", ret); - } - - return ret; - } - if (!strcmp(argv[1], "rx_dsm") || !strcmp(argv[1], "rx_dsm_10bit") || !strcmp(argv[1], "rx_dsm_11bit") || @@ -2074,5 +2430,5 @@ px4io_main(int argc, char *argv[]) bind(argc, argv); out: - errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug', 'recovery', 'limit', 'current', 'failsafe', 'bind', or 'update'"); + errx(1, "need a command, try 'start', 'stop', 'status', 'test', 'monitor', 'debug',\n 'recovery', 'limit', 'current', 'failsafe', 'min, 'max',\n 'idle', 'bind' or 'update'"); } |