diff options
Diffstat (limited to 'src/drivers')
25 files changed, 1142 insertions, 280 deletions
diff --git a/src/drivers/airspeed/airspeed.cpp b/src/drivers/airspeed/airspeed.cpp index 5e45cc936..f73a3ef01 100644 --- a/src/drivers/airspeed/airspeed.cpp +++ b/src/drivers/airspeed/airspeed.cpp @@ -91,7 +91,7 @@ Airspeed::Airspeed(int bus, int address, unsigned conversion_interval) : _comms_errors(perf_alloc(PC_COUNT, "airspeed_comms_errors")) { // enable debug() calls - _debug_enabled = true; + _debug_enabled = false; // work_cancel in the dtor will explode if we don't do this... memset(&_work, 0, sizeof(_work)); diff --git a/src/drivers/boards/px4fmu-v1/board_config.h b/src/drivers/boards/px4fmu-v1/board_config.h index 6f7166284..02c26b5c0 100644 --- a/src/drivers/boards/px4fmu-v1/board_config.h +++ b/src/drivers/boards/px4fmu-v1/board_config.h @@ -60,6 +60,7 @@ __BEGIN_DECLS /* PX4IO connection configuration */ #define PX4IO_SERIAL_DEVICE "/dev/ttyS2" +#define UDID_START 0x1FFF7A10 //#ifdef CONFIG_STM32_SPI2 //# error "SPI2 is not supported on this board" diff --git a/src/drivers/boards/px4fmu-v2/board_config.h b/src/drivers/boards/px4fmu-v2/board_config.h index a19ed9d24..7cfca7656 100644 --- a/src/drivers/boards/px4fmu-v2/board_config.h +++ b/src/drivers/boards/px4fmu-v2/board_config.h @@ -52,6 +52,8 @@ __BEGIN_DECLS /* these headers are not C++ safe */ #include <stm32.h> #include <arch/board/board.h> + +#define UDID_START 0x1FFF7A10 /**************************************************************************************************** * Definitions @@ -73,7 +75,7 @@ __BEGIN_DECLS /* PX4FMU GPIOs ***********************************************************************************/ /* LEDs */ -#define GPIO_LED1 (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN12) +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN12) /* External interrupts */ #define GPIO_EXTI_GYRO_DRDY (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN0) @@ -85,7 +87,7 @@ __BEGIN_DECLS #define GPIO_GYRO_DRDY_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTB|GPIO_PIN0) #define GPIO_MAG_DRDY_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTB|GPIO_PIN1) #define GPIO_ACCEL_DRDY_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTB|GPIO_PIN4) -#define GPIO_EXTI_MPU_DRDY (GPIO_INPUT|GPIO_PULLDOWN|GPIO_EXTI|GPIO_PORTD|GPIO_PIN15) +#define GPIO_EXTI_MPU_DRDY_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_EXTI|GPIO_PORTD|GPIO_PIN15) /* SPI1 off */ #define GPIO_SPI1_SCK_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_PORTA|GPIO_PIN5) @@ -96,7 +98,7 @@ __BEGIN_DECLS #define GPIO_SPI_CS_GYRO_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTC|GPIO_PIN13) #define GPIO_SPI_CS_ACCEL_MAG_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTC|GPIO_PIN15) #define GPIO_SPI_CS_BARO_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTD|GPIO_PIN7) -#define GPIO_SPI_CS_MPU (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTC|GPIO_PIN2) +#define GPIO_SPI_CS_MPU_OFF (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_2MHz|GPIO_PORTC|GPIO_PIN2) /* SPI chip selects */ #define GPIO_SPI_CS_GYRO (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN13) diff --git a/src/drivers/boards/px4fmu-v2/px4fmu2_init.c b/src/drivers/boards/px4fmu-v2/px4fmu2_init.c index 269ec238e..71414d62c 100644 --- a/src/drivers/boards/px4fmu-v2/px4fmu2_init.c +++ b/src/drivers/boards/px4fmu-v2/px4fmu2_init.c @@ -282,7 +282,7 @@ __EXPORT int nsh_archinitialize(void) SPI_SELECT(spi1, PX4_SPIDEV_MPU, false); up_udelay(20); - message("[boot] Successfully initialized SPI port 1\n"); + message("[boot] Initialized SPI port 1 (SENSORS)\n"); /* Get the SPI port for the FRAM */ @@ -294,20 +294,23 @@ __EXPORT int nsh_archinitialize(void) return -ENODEV; } - /* Default SPI2 to 37.5 MHz (F4 max) and de-assert the known chip selects. */ - SPI_SETFREQUENCY(spi2, 375000000); + /* Default SPI2 to 37.5 MHz (40 MHz rounded to nearest valid divider, F4 max) + * and de-assert the known chip selects. */ + + // XXX start with 10.4 MHz in FRAM usage and go up to 37.5 once validated + SPI_SETFREQUENCY(spi2, 12 * 1000 * 1000); SPI_SETBITS(spi2, 8); SPI_SETMODE(spi2, SPIDEV_MODE3); SPI_SELECT(spi2, SPIDEV_FLASH, false); - message("[boot] Successfully initialized SPI port 2\n"); + message("[boot] Initialized SPI port 2 (RAMTRON FRAM)\n"); #ifdef CONFIG_MMCSD /* First, get an instance of the SDIO interface */ sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO); if (!sdio) { - message("nsh_archinitialize: Failed to initialize SDIO slot %d\n", + message("[boot] Failed to initialize SDIO slot %d\n", CONFIG_NSH_MMCSDSLOTNO); return -ENODEV; } @@ -315,7 +318,7 @@ __EXPORT int nsh_archinitialize(void) /* Now bind the SDIO interface to the MMC/SD driver */ int ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio); if (ret != OK) { - message("nsh_archinitialize: Failed to bind SDIO to the MMC/SD driver: %d\n", ret); + message("[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret); return ret; } diff --git a/src/drivers/boards/px4io-v1/board_config.h b/src/drivers/boards/px4io-v1/board_config.h index c3f39addf..1be4877ba 100644 --- a/src/drivers/boards/px4io-v1/board_config.h +++ b/src/drivers/boards/px4io-v1/board_config.h @@ -58,11 +58,11 @@ /* PX4IO GPIOs **********************************************************************/ /* LEDs */ -#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\ +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|\ GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN14) -#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\ +#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|\ GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN15) -#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\ +#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|\ GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10) /* Safety switch button *************************************************************/ diff --git a/src/drivers/boards/px4io-v2/board_config.h b/src/drivers/boards/px4io-v2/board_config.h index 8da555211..ef9bb5cad 100644 --- a/src/drivers/boards/px4io-v2/board_config.h +++ b/src/drivers/boards/px4io-v2/board_config.h @@ -74,9 +74,9 @@ /* LEDS **********************************************************************/ -#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN14) -#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN15) -#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN13) +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN14) +#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN15) +#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTOD|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN13) /* Safety switch button *******************************************************/ @@ -114,7 +114,7 @@ /* XXX these should be UART pins */ #define GPIO_SBUS_INPUT (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|GPIO_PORTB|GPIO_PIN11) #define GPIO_SBUS_OUTPUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN10) -#define GPIO_SBUS_OENABLE (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN4) +#define GPIO_SBUS_OENABLE (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN4) /* * High-resolution timer diff --git a/src/drivers/boards/px4io-v2/px4iov2_init.c b/src/drivers/boards/px4io-v2/px4iov2_init.c index ccd01edf5..9f8c0eeb2 100644 --- a/src/drivers/boards/px4io-v2/px4iov2_init.c +++ b/src/drivers/boards/px4io-v2/px4iov2_init.c @@ -124,8 +124,6 @@ __EXPORT void stm32_boardinitialize(void) stm32_configgpio(GPIO_ADC_VSERVO); stm32_configgpio(GPIO_SBUS_INPUT); /* xxx alternate function */ - - stm32_gpiowrite(GPIO_SBUS_OUTPUT, false); stm32_configgpio(GPIO_SBUS_OUTPUT); /* sbus output enable is active low - disable it by default */ diff --git a/src/drivers/drv_pwm_output.h b/src/drivers/drv_pwm_output.h index 51f916f37..88da94b1e 100644 --- a/src/drivers/drv_pwm_output.h +++ b/src/drivers/drv_pwm_output.h @@ -189,6 +189,10 @@ ORB_DECLARE(output_pwm); /** get the maximum PWM value the output will send */ #define PWM_SERVO_GET_MAX_PWM _IOC(_PWM_SERVO_BASE, 19) +/** set the number of servos in (unsigned)arg - allows change of + * split between servos and GPIO */ +#define PWM_SERVO_SET_COUNT _IOC(_PWM_SERVO_BASE, 20) + /** set a single servo to a specific value */ #define PWM_SERVO_SET(_servo) _IOC(_PWM_SERVO_BASE, 0x20 + _servo) diff --git a/src/drivers/frsky_telemetry/frsky_data.c b/src/drivers/frsky_telemetry/frsky_data.c new file mode 100644 index 000000000..e201ecbb3 --- /dev/null +++ b/src/drivers/frsky_telemetry/frsky_data.c @@ -0,0 +1,289 @@ +/**************************************************************************** + * + * Copyright (c) 2013-2014 PX4 Development Team. All rights reserved. + * Author: Stefan Rado <px4@sradonia.net> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file frsky_data.c + * @author Stefan Rado <px4@sradonia.net> + * + * FrSky telemetry implementation. + * + */ + +#include "frsky_data.h" + +#include <stdlib.h> +#include <stdio.h> +#include <string.h> +#include <arch/math.h> +#include <geo/geo.h> + +#include <uORB/topics/battery_status.h> +#include <uORB/topics/sensor_combined.h> +#include <uORB/topics/vehicle_global_position.h> +#include <uORB/topics/vehicle_status.h> + +/* FrSky sensor hub data IDs */ +#define FRSKY_ID_GPS_ALT_BP 0x01 +#define FRSKY_ID_TEMP1 0x02 +#define FRSKY_ID_RPM 0x03 +#define FRSKY_ID_FUEL 0x04 +#define FRSKY_ID_TEMP2 0x05 +#define FRSKY_ID_VOLTS 0x06 +#define FRSKY_ID_GPS_ALT_AP 0x09 +#define FRSKY_ID_BARO_ALT_BP 0x10 +#define FRSKY_ID_GPS_SPEED_BP 0x11 +#define FRSKY_ID_GPS_LONG_BP 0x12 +#define FRSKY_ID_GPS_LAT_BP 0x13 +#define FRSKY_ID_GPS_COURS_BP 0x14 +#define FRSKY_ID_GPS_DAY_MONTH 0x15 +#define FRSKY_ID_GPS_YEAR 0x16 +#define FRSKY_ID_GPS_HOUR_MIN 0x17 +#define FRSKY_ID_GPS_SEC 0x18 +#define FRSKY_ID_GPS_SPEED_AP 0x19 +#define FRSKY_ID_GPS_LONG_AP 0x1A +#define FRSKY_ID_GPS_LAT_AP 0x1B +#define FRSKY_ID_GPS_COURS_AP 0x1C +#define FRSKY_ID_BARO_ALT_AP 0x21 +#define FRSKY_ID_GPS_LONG_EW 0x22 +#define FRSKY_ID_GPS_LAT_NS 0x23 +#define FRSKY_ID_ACCEL_X 0x24 +#define FRSKY_ID_ACCEL_Y 0x25 +#define FRSKY_ID_ACCEL_Z 0x26 +#define FRSKY_ID_CURRENT 0x28 +#define FRSKY_ID_VARIO 0x30 +#define FRSKY_ID_VFAS 0x39 +#define FRSKY_ID_VOLTS_BP 0x3A +#define FRSKY_ID_VOLTS_AP 0x3B + +#define frac(f) (f - (int)f) + +static int battery_sub = -1; +static int sensor_sub = -1; +static int global_position_sub = -1; +static int vehicle_status_sub = -1; + +/** + * Initializes the uORB subscriptions. + */ +void frsky_init() +{ + battery_sub = orb_subscribe(ORB_ID(battery_status)); + global_position_sub = orb_subscribe(ORB_ID(vehicle_global_position)); + sensor_sub = orb_subscribe(ORB_ID(sensor_combined)); + vehicle_status_sub = orb_subscribe(ORB_ID(vehicle_status)); +} + +/** + * Sends a 0x5E start/stop byte. + */ +static void frsky_send_startstop(int uart) +{ + static const uint8_t c = 0x5E; + write(uart, &c, sizeof(c)); +} + +/** + * Sends one byte, performing byte-stuffing if necessary. + */ +static void frsky_send_byte(int uart, uint8_t value) +{ + const uint8_t x5E[] = { 0x5D, 0x3E }; + const uint8_t x5D[] = { 0x5D, 0x3D }; + + switch (value) { + case 0x5E: + write(uart, x5E, sizeof(x5E)); + break; + + case 0x5D: + write(uart, x5D, sizeof(x5D)); + break; + + default: + write(uart, &value, sizeof(value)); + break; + } +} + +/** + * Sends one data id/value pair. + */ +static void frsky_send_data(int uart, uint8_t id, int16_t data) +{ + /* Cast data to unsigned, because signed shift might behave incorrectly */ + uint16_t udata = data; + + frsky_send_startstop(uart); + + frsky_send_byte(uart, id); + frsky_send_byte(uart, udata); /* LSB */ + frsky_send_byte(uart, udata >> 8); /* MSB */ +} + +/** + * Sends frame 1 (every 200ms): + * acceleration values, barometer altitude, temperature, battery voltage & current + */ +void frsky_send_frame1(int uart) +{ + /* get a local copy of the current sensor values */ + struct sensor_combined_s raw; + memset(&raw, 0, sizeof(raw)); + orb_copy(ORB_ID(sensor_combined), sensor_sub, &raw); + + /* get a local copy of the battery data */ + struct battery_status_s battery; + memset(&battery, 0, sizeof(battery)); + orb_copy(ORB_ID(battery_status), battery_sub, &battery); + + /* send formatted frame */ + frsky_send_data(uart, FRSKY_ID_ACCEL_X, + roundf(raw.accelerometer_m_s2[0] * 1000.0f)); + frsky_send_data(uart, FRSKY_ID_ACCEL_Y, + roundf(raw.accelerometer_m_s2[1] * 1000.0f)); + frsky_send_data(uart, FRSKY_ID_ACCEL_Z, + roundf(raw.accelerometer_m_s2[2] * 1000.0f)); + + frsky_send_data(uart, FRSKY_ID_BARO_ALT_BP, + raw.baro_alt_meter); + frsky_send_data(uart, FRSKY_ID_BARO_ALT_AP, + roundf(frac(raw.baro_alt_meter) * 100.0f)); + + frsky_send_data(uart, FRSKY_ID_TEMP1, + roundf(raw.baro_temp_celcius)); + + frsky_send_data(uart, FRSKY_ID_VFAS, + roundf(battery.voltage_v * 10.0f)); + frsky_send_data(uart, FRSKY_ID_CURRENT, + (battery.current_a < 0) ? 0 : roundf(battery.current_a * 10.0f)); + + frsky_send_startstop(uart); +} + +/** + * Formats the decimal latitude/longitude to the required degrees/minutes/seconds. + */ +static float frsky_format_gps(float dec) +{ + float dms_deg = (int) dec; + float dec_deg = dec - dms_deg; + float dms_min = (int) (dec_deg * 60); + float dec_min = (dec_deg * 60) - dms_min; + float dms_sec = dec_min * 60; + + return (dms_deg * 100.0f) + dms_min + (dms_sec / 100.0f); +} + +/** + * Sends frame 2 (every 1000ms): + * GPS course, latitude, longitude, ground speed, GPS altitude, remaining battery level + */ +void frsky_send_frame2(int uart) +{ + /* get a local copy of the global position data */ + struct vehicle_global_position_s global_pos; + memset(&global_pos, 0, sizeof(global_pos)); + orb_copy(ORB_ID(vehicle_global_position), global_position_sub, &global_pos); + + /* get a local copy of the vehicle status data */ + struct vehicle_status_s vehicle_status; + memset(&vehicle_status, 0, sizeof(vehicle_status)); + orb_copy(ORB_ID(vehicle_status), vehicle_status_sub, &vehicle_status); + + /* send formatted frame */ + float course = 0, lat = 0, lon = 0, speed = 0, alt = 0; + char lat_ns = 0, lon_ew = 0; + int sec = 0; + if (global_pos.valid) { + time_t time_gps = global_pos.time_gps_usec / 1000000; + struct tm *tm_gps = gmtime(&time_gps); + + course = (global_pos.yaw + M_PI_F) / M_PI_F * 180.0f; + lat = frsky_format_gps(abs(global_pos.lat)); + lat_ns = (global_pos.lat < 0) ? 'S' : 'N'; + lon = frsky_format_gps(abs(global_pos.lon)); + lon_ew = (global_pos.lon < 0) ? 'W' : 'E'; + speed = sqrtf(global_pos.vel_n * global_pos.vel_n + global_pos.vel_e * global_pos.vel_e) + * 25.0f / 46.0f; + alt = global_pos.alt; + sec = tm_gps->tm_sec; + } + + frsky_send_data(uart, FRSKY_ID_GPS_COURS_BP, course); + frsky_send_data(uart, FRSKY_ID_GPS_COURS_AP, frac(course) * 1000.0f); + + frsky_send_data(uart, FRSKY_ID_GPS_LAT_BP, lat); + frsky_send_data(uart, FRSKY_ID_GPS_LAT_AP, frac(lat) * 10000.0f); + frsky_send_data(uart, FRSKY_ID_GPS_LAT_NS, lat_ns); + + frsky_send_data(uart, FRSKY_ID_GPS_LONG_BP, lon); + frsky_send_data(uart, FRSKY_ID_GPS_LONG_AP, frac(lon) * 10000.0f); + frsky_send_data(uart, FRSKY_ID_GPS_LONG_EW, lon_ew); + + frsky_send_data(uart, FRSKY_ID_GPS_SPEED_BP, speed); + frsky_send_data(uart, FRSKY_ID_GPS_SPEED_AP, frac(speed) * 100.0f); + + frsky_send_data(uart, FRSKY_ID_GPS_ALT_BP, alt); + frsky_send_data(uart, FRSKY_ID_GPS_ALT_AP, frac(alt) * 100.0f); + + frsky_send_data(uart, FRSKY_ID_FUEL, + roundf(vehicle_status.battery_remaining * 100.0f)); + + frsky_send_data(uart, FRSKY_ID_GPS_SEC, sec); + + frsky_send_startstop(uart); +} + +/** + * Sends frame 3 (every 5000ms): + * GPS date & time + */ +void frsky_send_frame3(int uart) +{ + /* get a local copy of the battery data */ + struct vehicle_global_position_s global_pos; + memset(&global_pos, 0, sizeof(global_pos)); + orb_copy(ORB_ID(vehicle_global_position), global_position_sub, &global_pos); + + /* send formatted frame */ + time_t time_gps = global_pos.time_gps_usec / 1000000; + struct tm *tm_gps = gmtime(&time_gps); + uint16_t hour_min = (tm_gps->tm_min << 8) | (tm_gps->tm_hour & 0xff); + frsky_send_data(uart, FRSKY_ID_GPS_DAY_MONTH, tm_gps->tm_mday); + frsky_send_data(uart, FRSKY_ID_GPS_YEAR, tm_gps->tm_year); + frsky_send_data(uart, FRSKY_ID_GPS_HOUR_MIN, hour_min); + frsky_send_data(uart, FRSKY_ID_GPS_SEC, tm_gps->tm_sec); + + frsky_send_startstop(uart); +} diff --git a/src/drivers/frsky_telemetry/frsky_data.h b/src/drivers/frsky_telemetry/frsky_data.h new file mode 100644 index 000000000..a7d9eee53 --- /dev/null +++ b/src/drivers/frsky_telemetry/frsky_data.h @@ -0,0 +1,51 @@ +/**************************************************************************** + * + * Copyright (c) 2013-2014 PX4 Development Team. All rights reserved. + * Author: Stefan Rado <px4@sradonia.net> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file frsky_data.h + * @author Stefan Rado <px4@sradonia.net> + * + * FrSky telemetry implementation. + * + */ +#ifndef _FRSKY_DATA_H +#define _FRSKY_DATA_H + +// Public functions +void frsky_init(void); +void frsky_send_frame1(int uart); +void frsky_send_frame2(int uart); +void frsky_send_frame3(int uart); + +#endif /* _FRSKY_TELEMETRY_H */ diff --git a/src/drivers/frsky_telemetry/frsky_telemetry.c b/src/drivers/frsky_telemetry/frsky_telemetry.c new file mode 100644 index 000000000..7b08ca69e --- /dev/null +++ b/src/drivers/frsky_telemetry/frsky_telemetry.c @@ -0,0 +1,266 @@ +/**************************************************************************** + * + * Copyright (c) 2013-2014 PX4 Development Team. All rights reserved. + * Author: Stefan Rado <px4@sradonia.net> + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file frsky_telemetry.c + * @author Stefan Rado <px4@sradonia.net> + * + * FrSky telemetry implementation. + * + * This daemon emulates an FrSky sensor hub by periodically sending data + * packets to an attached FrSky receiver. + * + */ + +#include <stdlib.h> +#include <stdio.h> +#include <stdbool.h> +#include <string.h> +#include <sys/types.h> +#include <fcntl.h> +#include <unistd.h> +#include <systemlib/err.h> +#include <systemlib/systemlib.h> +#include <termios.h> + +#include "frsky_data.h" + + +/* thread state */ +static volatile bool thread_should_exit = false; +static volatile bool thread_running = false; +static int frsky_task; + +/* functions */ +static int frsky_open_uart(const char *uart_name, struct termios *uart_config_original); +static void usage(void); +static int frsky_telemetry_thread_main(int argc, char *argv[]); +__EXPORT int frsky_telemetry_main(int argc, char *argv[]); + + +/** + * Opens the UART device and sets all required serial parameters. + */ +static int frsky_open_uart(const char *uart_name, struct termios *uart_config_original) +{ + /* Open UART */ + const int uart = open(uart_name, O_WRONLY | O_NOCTTY); + + if (uart < 0) { + err(1, "Error opening port: %s", uart_name); + } + + /* Back up the original UART configuration to restore it after exit */ + int termios_state; + if ((termios_state = tcgetattr(uart, uart_config_original)) < 0) { + warnx("ERROR get termios config %s: %d\n", uart_name, termios_state); + close(uart); + return -1; + } + + /* Fill the struct for the new configuration */ + struct termios uart_config; + tcgetattr(uart, &uart_config); + + /* Disable output post-processing */ + uart_config.c_oflag &= ~OPOST; + + /* Set baud rate */ + static const speed_t speed = B9600; + + if (cfsetispeed(&uart_config, speed) < 0 || cfsetospeed(&uart_config, speed) < 0) { + warnx("ERROR setting baudrate / termios config for %s: %d (cfsetispeed, cfsetospeed)\n", uart_name, termios_state); + close(uart); + return -1; + } + + if ((termios_state = tcsetattr(uart, TCSANOW, &uart_config)) < 0) { + warnx("ERROR setting baudrate / termios config for %s (tcsetattr)\n", uart_name); + close(uart); + return -1; + } + + return uart; +} + +/** + * Print command usage information + */ +static void usage() +{ + fprintf(stderr, + "usage: frsky_telemetry start [-d <devicename>]\n" + " frsky_telemetry stop\n" + " frsky_telemetry status\n"); + exit(1); +} + +/** + * The daemon thread. + */ +static int frsky_telemetry_thread_main(int argc, char *argv[]) +{ + /* Default values for arguments */ + char *device_name = "/dev/ttyS1"; /* USART2 */ + + /* Work around some stupidity in task_create's argv handling */ + argc -= 2; + argv += 2; + + int ch; + while ((ch = getopt(argc, argv, "d:")) != EOF) { + switch (ch) { + case 'd': + device_name = optarg; + break; + + default: + usage(); + break; + } + } + + /* Print welcome text */ + warnx("FrSky telemetry interface starting..."); + + /* Open UART */ + struct termios uart_config_original; + const int uart = frsky_open_uart(device_name, &uart_config_original); + + if (uart < 0) + err(1, "could not open %s", device_name); + + /* Subscribe to topics */ + frsky_init(); + + thread_running = true; + + /* Main thread loop */ + unsigned int iteration = 0; + while (!thread_should_exit) { + + /* Sleep 200 ms */ + usleep(200000); + + /* Send frame 1 (every 200ms): acceleration values, altitude (vario), temperatures, current & voltages, RPM */ + frsky_send_frame1(uart); + + /* Send frame 2 (every 1000ms): course, latitude, longitude, speed, altitude (GPS), fuel level */ + if (iteration % 5 == 0) + { + frsky_send_frame2(uart); + } + + /* Send frame 3 (every 5000ms): date, time */ + if (iteration % 25 == 0) + { + frsky_send_frame3(uart); + + iteration = 0; + } + + iteration++; + } + + /* Reset the UART flags to original state */ + tcsetattr(uart, TCSANOW, &uart_config_original); + close(uart); + + thread_running = false; + return 0; +} + +/** + * The main command function. + * Processes command line arguments and starts the daemon. + */ +int frsky_telemetry_main(int argc, char *argv[]) +{ + if (argc < 2) { + warnx("missing command"); + usage(); + } + + if (!strcmp(argv[1], "start")) { + + /* this is not an error */ + if (thread_running) + errx(0, "frsky_telemetry already running"); + + thread_should_exit = false; + frsky_task = task_spawn_cmd("frsky_telemetry", + SCHED_DEFAULT, + SCHED_PRIORITY_DEFAULT, + 2048, + frsky_telemetry_thread_main, + (const char **)argv); + + while (!thread_running) { + usleep(200); + } + + exit(0); + } + + if (!strcmp(argv[1], "stop")) { + + /* this is not an error */ + if (!thread_running) + errx(0, "frsky_telemetry already stopped"); + + thread_should_exit = true; + + while (thread_running) { + usleep(200000); + warnx("."); + } + + warnx("terminated."); + exit(0); + } + + if (!strcmp(argv[1], "status")) { + if (thread_running) { + errx(0, "running"); + + } else { + errx(1, "not running"); + } + } + + warnx("unrecognized command"); + usage(); + /* not getting here */ + return 0; +} diff --git a/src/drivers/frsky_telemetry/module.mk b/src/drivers/frsky_telemetry/module.mk new file mode 100644 index 000000000..1632c74f7 --- /dev/null +++ b/src/drivers/frsky_telemetry/module.mk @@ -0,0 +1,41 @@ +############################################################################ +# +# Copyright (c) 2013-2014 PX4 Development Team. All rights reserved. +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name PX4 nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +# +# FrSky telemetry application. +# + +MODULE_COMMAND = frsky_telemetry + +SRCS = frsky_data.c \ + frsky_telemetry.c diff --git a/src/drivers/gps/gps.cpp b/src/drivers/gps/gps.cpp index fc500a9ec..6b72d560f 100644 --- a/src/drivers/gps/gps.cpp +++ b/src/drivers/gps/gps.cpp @@ -85,7 +85,7 @@ static const int ERROR = -1; class GPS : public device::CDev { public: - GPS(const char *uart_path); + GPS(const char *uart_path, bool fake_gps); virtual ~GPS(); virtual int init(); @@ -112,6 +112,7 @@ private: struct vehicle_gps_position_s _report; ///< uORB topic for gps position orb_advert_t _report_pub; ///< uORB pub for gps position float _rate; ///< position update rate + bool _fake_gps; ///< fake gps output /** @@ -156,7 +157,7 @@ GPS *g_dev; } -GPS::GPS(const char *uart_path) : +GPS::GPS(const char *uart_path, bool fake_gps) : CDev("gps", GPS_DEVICE_PATH), _task_should_exit(false), _healthy(false), @@ -164,7 +165,8 @@ GPS::GPS(const char *uart_path) : _mode(GPS_DRIVER_MODE_UBX), _Helper(nullptr), _report_pub(-1), - _rate(0.0f) + _rate(0.0f), + _fake_gps(fake_gps) { /* store port name */ strncpy(_port, uart_path, sizeof(_port)); @@ -264,98 +266,133 @@ GPS::task_main() /* loop handling received serial bytes and also configuring in between */ while (!_task_should_exit) { - if (_Helper != nullptr) { - delete(_Helper); - /* set to zero to ensure parser is not used while not instantiated */ - _Helper = nullptr; - } + if (_fake_gps) { + + _report.timestamp_position = hrt_absolute_time(); + _report.lat = (int32_t)47.378301e7f; + _report.lon = (int32_t)8.538777e7f; + _report.alt = (int32_t)400e3f; + _report.timestamp_variance = hrt_absolute_time(); + _report.s_variance_m_s = 10.0f; + _report.p_variance_m = 10.0f; + _report.c_variance_rad = 0.1f; + _report.fix_type = 3; + _report.eph_m = 10.0f; + _report.epv_m = 10.0f; + _report.timestamp_velocity = hrt_absolute_time(); + _report.vel_n_m_s = 0.0f; + _report.vel_e_m_s = 0.0f; + _report.vel_d_m_s = 0.0f; + _report.vel_m_s = sqrtf(_report.vel_n_m_s * _report.vel_n_m_s + _report.vel_e_m_s * _report.vel_e_m_s + _report.vel_d_m_s * _report.vel_d_m_s); + _report.cog_rad = 0.0f; + _report.vel_ned_valid = true; + + //no time and satellite information simulated + + if (_report_pub > 0) { + orb_publish(ORB_ID(vehicle_gps_position), _report_pub, &_report); + + } else { + _report_pub = orb_advertise(ORB_ID(vehicle_gps_position), &_report); + } - switch (_mode) { - case GPS_DRIVER_MODE_UBX: - _Helper = new UBX(_serial_fd, &_report); - break; + usleep(2e5); - case GPS_DRIVER_MODE_MTK: - _Helper = new MTK(_serial_fd, &_report); - break; + } else { - default: - break; - } + if (_Helper != nullptr) { + delete(_Helper); + /* set to zero to ensure parser is not used while not instantiated */ + _Helper = nullptr; + } - unlock(); + switch (_mode) { + case GPS_DRIVER_MODE_UBX: + _Helper = new UBX(_serial_fd, &_report); + break; + + case GPS_DRIVER_MODE_MTK: + _Helper = new MTK(_serial_fd, &_report); + break; + + default: + break; + } - if (_Helper->configure(_baudrate) == 0) { unlock(); - // GPS is obviously detected successfully, reset statistics - _Helper->reset_update_rates(); + if (_Helper->configure(_baudrate) == 0) { + unlock(); - while (_Helper->receive(TIMEOUT_5HZ) > 0 && !_task_should_exit) { -// lock(); - /* opportunistic publishing - else invalid data would end up on the bus */ - if (_report_pub > 0) { - orb_publish(ORB_ID(vehicle_gps_position), _report_pub, &_report); + // GPS is obviously detected successfully, reset statistics + _Helper->reset_update_rates(); - } else { - _report_pub = orb_advertise(ORB_ID(vehicle_gps_position), &_report); - } + while (_Helper->receive(TIMEOUT_5HZ) > 0 && !_task_should_exit) { + // lock(); + /* opportunistic publishing - else invalid data would end up on the bus */ + if (_report_pub > 0) { + orb_publish(ORB_ID(vehicle_gps_position), _report_pub, &_report); + + } else { + _report_pub = orb_advertise(ORB_ID(vehicle_gps_position), &_report); + } - last_rate_count++; + last_rate_count++; - /* measure update rate every 5 seconds */ - if (hrt_absolute_time() - last_rate_measurement > RATE_MEASUREMENT_PERIOD) { - _rate = last_rate_count / ((float)((hrt_absolute_time() - last_rate_measurement)) / 1000000.0f); - last_rate_measurement = hrt_absolute_time(); - last_rate_count = 0; - _Helper->store_update_rates(); - _Helper->reset_update_rates(); - } + /* measure update rate every 5 seconds */ + if (hrt_absolute_time() - last_rate_measurement > RATE_MEASUREMENT_PERIOD) { + _rate = last_rate_count / ((float)((hrt_absolute_time() - last_rate_measurement)) / 1000000.0f); + last_rate_measurement = hrt_absolute_time(); + last_rate_count = 0; + _Helper->store_update_rates(); + _Helper->reset_update_rates(); + } - if (!_healthy) { - char *mode_str = "unknown"; + if (!_healthy) { + char *mode_str = "unknown"; - switch (_mode) { - case GPS_DRIVER_MODE_UBX: - mode_str = "UBX"; - break; + switch (_mode) { + case GPS_DRIVER_MODE_UBX: + mode_str = "UBX"; + break; - case GPS_DRIVER_MODE_MTK: - mode_str = "MTK"; - break; + case GPS_DRIVER_MODE_MTK: + mode_str = "MTK"; + break; - default: - break; + default: + break; + } + + warnx("module found: %s", mode_str); + _healthy = true; } + } - warnx("module found: %s", mode_str); - _healthy = true; + if (_healthy) { + warnx("module lost"); + _healthy = false; + _rate = 0.0f; } - } - if (_healthy) { - warnx("module lost"); - _healthy = false; - _rate = 0.0f; + lock(); } lock(); - } - - lock(); - /* select next mode */ - switch (_mode) { - case GPS_DRIVER_MODE_UBX: - _mode = GPS_DRIVER_MODE_MTK; - break; + /* select next mode */ + switch (_mode) { + case GPS_DRIVER_MODE_UBX: + _mode = GPS_DRIVER_MODE_MTK; + break; - case GPS_DRIVER_MODE_MTK: - _mode = GPS_DRIVER_MODE_UBX; - break; + case GPS_DRIVER_MODE_MTK: + _mode = GPS_DRIVER_MODE_UBX; + break; - default: - break; + default: + break; + } } } @@ -417,7 +454,7 @@ namespace gps GPS *g_dev; -void start(const char *uart_path); +void start(const char *uart_path, bool fake_gps); void stop(); void test(); void reset(); @@ -427,7 +464,7 @@ void info(); * Start the driver. */ void -start(const char *uart_path) +start(const char *uart_path, bool fake_gps) { int fd; @@ -435,7 +472,7 @@ start(const char *uart_path) errx(1, "already started"); /* create the driver */ - g_dev = new GPS(uart_path); + g_dev = new GPS(uart_path, fake_gps); if (g_dev == nullptr) goto fail; @@ -527,6 +564,7 @@ gps_main(int argc, char *argv[]) /* set to default */ char *device_name = GPS_DEFAULT_UART_PORT; + bool fake_gps = false; /* * Start/load the driver. @@ -542,7 +580,13 @@ gps_main(int argc, char *argv[]) } } - gps::start(device_name); + /* Detect fake gps option */ + for (int i = 2; i < argc; i++) { + if (!strcmp(argv[i], "-f")) + fake_gps = true; + } + + gps::start(device_name, fake_gps); } if (!strcmp(argv[1], "stop")) @@ -567,5 +611,5 @@ gps_main(int argc, char *argv[]) gps::info(); out: - errx(1, "unrecognized command, try 'start', 'stop', 'test', 'reset' or 'status' [-d /dev/ttyS0-n]"); + errx(1, "unrecognized command, try 'start', 'stop', 'test', 'reset' or 'status' [-d /dev/ttyS0-n][-f]"); } diff --git a/src/drivers/hil/hil.cpp b/src/drivers/hil/hil.cpp index c1d73dd87..0a047f38f 100644 --- a/src/drivers/hil/hil.cpp +++ b/src/drivers/hil/hil.cpp @@ -1,6 +1,6 @@ /**************************************************************************** * - * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * Copyright (c) 2012-2014 PX4 Development Team. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions @@ -193,9 +193,10 @@ HIL::~HIL() } while (_task != -1); } - /* clean up the alternate device node */ - if (_primary_pwm_device) - unregister_driver(PWM_OUTPUT_DEVICE_PATH); + // XXX already claimed with CDEV + // /* clean up the alternate device node */ + // if (_primary_pwm_device) + // unregister_driver(PWM_OUTPUT_DEVICE_PATH); g_hil = nullptr; } diff --git a/src/drivers/hmc5883/hmc5883.cpp b/src/drivers/hmc5883/hmc5883.cpp index d3b99ae66..9b9c11af2 100644 --- a/src/drivers/hmc5883/hmc5883.cpp +++ b/src/drivers/hmc5883/hmc5883.cpp @@ -849,42 +849,24 @@ HMC5883::collect() /* scale values for output */ - /* - * 1) Scale raw value to SI units using scaling from datasheet. - * 2) Subtract static offset (in SI units) - * 3) Scale the statically calibrated values with a linear - * dynamically obtained factor - * - * Note: the static sensor offset is the number the sensor outputs - * at a nominally 'zero' input. Therefore the offset has to - * be subtracted. - * - * Example: A gyro outputs a value of 74 at zero angular rate - * the offset is 74 from the origin and subtracting - * 74 from all measurements centers them around zero. - */ - #ifdef PX4_I2C_BUS_ONBOARD if (_bus == PX4_I2C_BUS_ONBOARD) { - /* to align the sensor axes with the board, x and y need to be flipped */ - new_report.x = ((report.y * _range_scale) - _scale.x_offset) * _scale.x_scale; - /* flip axes and negate value for y */ - new_report.y = ((-report.x * _range_scale) - _scale.y_offset) * _scale.y_scale; - /* z remains z */ - new_report.z = ((report.z * _range_scale) - _scale.z_offset) * _scale.z_scale; - } else { -#endif - /* the standard external mag by 3DR has x pointing to the right, y pointing backwards, and z down, - * therefore switch x and y and invert y */ - new_report.x = ((-report.y * _range_scale) - _scale.x_offset) * _scale.x_scale; - /* flip axes and negate value for y */ - new_report.y = ((report.x * _range_scale) - _scale.y_offset) * _scale.y_scale; - /* z remains z */ - new_report.z = ((report.z * _range_scale) - _scale.z_offset) * _scale.z_scale; -#ifdef PX4_I2C_BUS_ONBOARD - } + // convert onboard so it matches offboard for the + // scaling below + report.y = -report.y; + report.x = -report.x; + } #endif + /* the standard external mag by 3DR has x pointing to the + * right, y pointing backwards, and z down, therefore switch x + * and y and invert y */ + new_report.x = ((-report.y * _range_scale) - _scale.x_offset) * _scale.x_scale; + /* flip axes and negate value for y */ + new_report.y = ((report.x * _range_scale) - _scale.y_offset) * _scale.y_scale; + /* z remains z */ + new_report.z = ((report.z * _range_scale) - _scale.z_offset) * _scale.z_scale; + if (_mag_topic != -1) { /* publish it */ orb_publish(ORB_ID(sensor_mag), _mag_topic, &new_report); @@ -910,6 +892,7 @@ int HMC5883::calibrate(struct file *filp, unsigned enable) struct mag_report report; ssize_t sz; int ret = 1; + uint8_t good_count = 0; // XXX do something smarter here int fd = (int)enable; @@ -932,31 +915,16 @@ int HMC5883::calibrate(struct file *filp, unsigned enable) 1.0f, }; - float avg_excited[3] = {0.0f, 0.0f, 0.0f}; - unsigned i; + float sum_excited[3] = {0.0f, 0.0f, 0.0f}; - warnx("starting mag scale calibration"); + /* expected axis scaling. The datasheet says that 766 will + * be places in the X and Y axes and 713 in the Z + * axis. Experiments show that in fact 766 is placed in X, + * and 713 in Y and Z. This is relative to a base of 660 + * LSM/Ga, giving 1.16 and 1.08 */ + float expected_cal[3] = { 1.16f, 1.08f, 1.08f }; - /* do a simple demand read */ - sz = read(filp, (char *)&report, sizeof(report)); - - if (sz != sizeof(report)) { - warn("immediate read failed"); - ret = 1; - goto out; - } - - warnx("current measurement: %.6f %.6f %.6f", (double)report.x, (double)report.y, (double)report.z); - warnx("time: %lld", report.timestamp); - warnx("sampling 500 samples for scaling offset"); - - /* set the queue depth to 10 */ - /* don't do this for now, it can lead to a crash in start() respectively work_queue() */ -// if (OK != ioctl(filp, SENSORIOCSQUEUEDEPTH, 10)) { -// warn("failed to set queue depth"); -// ret = 1; -// goto out; -// } + warnx("starting mag scale calibration"); /* start the sensor polling at 50 Hz */ if (OK != ioctl(filp, SENSORIOCSPOLLRATE, 50)) { @@ -965,8 +933,9 @@ int HMC5883::calibrate(struct file *filp, unsigned enable) goto out; } - /* Set to 2.5 Gauss */ - if (OK != ioctl(filp, MAGIOCSRANGE, 2)) { + /* Set to 2.5 Gauss. We ask for 3 to get the right part of + * the chained if statement above. */ + if (OK != ioctl(filp, MAGIOCSRANGE, 3)) { warnx("failed to set 2.5 Ga range"); ret = 1; goto out; @@ -990,8 +959,8 @@ int HMC5883::calibrate(struct file *filp, unsigned enable) goto out; } - /* read the sensor 10x and report each value */ - for (i = 0; i < 500; i++) { + // discard 10 samples to let the sensor settle + for (uint8_t i = 0; i < 10; i++) { struct pollfd fds; /* wait for data to be ready */ @@ -1009,32 +978,69 @@ int HMC5883::calibrate(struct file *filp, unsigned enable) if (sz != sizeof(report)) { warn("periodic read failed"); + ret = -EIO; goto out; + } + } - } else { - avg_excited[0] += report.x; - avg_excited[1] += report.y; - avg_excited[2] += report.z; + /* read the sensor up to 50x, stopping when we have 10 good values */ + for (uint8_t i = 0; i < 50 && good_count < 10; i++) { + struct pollfd fds; + + /* wait for data to be ready */ + fds.fd = fd; + fds.events = POLLIN; + ret = ::poll(&fds, 1, 2000); + + if (ret != 1) { + warn("timed out waiting for sensor data"); + goto out; + } + + /* now go get it */ + sz = ::read(fd, &report, sizeof(report)); + + if (sz != sizeof(report)) { + warn("periodic read failed"); + ret = -EIO; + goto out; + } + float cal[3] = {fabsf(expected_cal[0] / report.x), + fabsf(expected_cal[1] / report.y), + fabsf(expected_cal[2] / report.z)}; + + if (cal[0] > 0.7f && cal[0] < 1.35f && + cal[1] > 0.7f && cal[1] < 1.35f && + cal[2] > 0.7f && cal[2] < 1.35f) { + good_count++; + sum_excited[0] += cal[0]; + sum_excited[1] += cal[1]; + sum_excited[2] += cal[2]; } //warnx("periodic read %u", i); //warnx("measurement: %.6f %.6f %.6f", (double)report.x, (double)report.y, (double)report.z); + //warnx("cal: %.6f %.6f %.6f", (double)cal[0], (double)cal[1], (double)cal[2]); } - avg_excited[0] /= i; - avg_excited[1] /= i; - avg_excited[2] /= i; + if (good_count < 5) { + warn("failed calibration"); + ret = -EIO; + goto out; + } - warnx("done. Performed %u reads", i); - warnx("measurement avg: %.6f %.6f %.6f", (double)avg_excited[0], (double)avg_excited[1], (double)avg_excited[2]); +#if 0 + warnx("measurement avg: %.6f %.6f %.6f", + (double)sum_excited[0]/good_count, + (double)sum_excited[1]/good_count, + (double)sum_excited[2]/good_count); +#endif float scaling[3]; - /* calculate axis scaling */ - scaling[0] = fabsf(1.16f / avg_excited[0]); - /* second axis inverted */ - scaling[1] = fabsf(1.16f / -avg_excited[1]); - scaling[2] = fabsf(1.08f / avg_excited[2]); + scaling[0] = sum_excited[0] / good_count; + scaling[1] = sum_excited[1] / good_count; + scaling[2] = sum_excited[2] / good_count; warnx("axes scaling: %.6f %.6f %.6f", (double)scaling[0], (double)scaling[1], (double)scaling[2]); @@ -1165,6 +1171,8 @@ int HMC5883::set_excitement(unsigned enable) conf_reg &= ~0x03; } + // ::printf("set_excitement enable=%d regA=0x%x\n", (int)enable, (unsigned)conf_reg); + ret = write_reg(ADDR_CONF_A, conf_reg); if (OK != ret) @@ -1173,6 +1181,8 @@ int HMC5883::set_excitement(unsigned enable) uint8_t conf_reg_ret; read_reg(ADDR_CONF_A, conf_reg_ret); + //print_info(); + return !(conf_reg == conf_reg_ret); } @@ -1211,6 +1221,10 @@ HMC5883::print_info() perf_print_counter(_comms_errors); perf_print_counter(_buffer_overflows); printf("poll interval: %u ticks\n", _measure_ticks); + printf("offsets (%.2f %.2f %.2f)\n", (double)_scale.x_offset, (double)_scale.y_offset, (double)_scale.z_offset); + printf("scaling (%.2f %.2f %.2f) 1/range_scale %.2f range_ga %.2f\n", + (double)_scale.x_scale, (double)_scale.y_scale, (double)_scale.z_scale, + (double)1.0/_range_scale, (double)_range_ga); _reports->print_info("report queue"); } diff --git a/src/drivers/hott/hott_sensors/hott_sensors.cpp b/src/drivers/hott/hott_sensors/hott_sensors.cpp index e322c6349..a3d3a3933 100644 --- a/src/drivers/hott/hott_sensors/hott_sensors.cpp +++ b/src/drivers/hott/hott_sensors/hott_sensors.cpp @@ -211,7 +211,7 @@ hott_sensors_main(int argc, char *argv[]) thread_should_exit = false; deamon_task = task_spawn_cmd(daemon_name, SCHED_DEFAULT, - SCHED_PRIORITY_MAX - 40, + SCHED_PRIORITY_DEFAULT, 1024, hott_sensors_thread_main, (argv) ? (const char **)&argv[2] : (const char **)NULL); diff --git a/src/drivers/hott/hott_telemetry/hott_telemetry.cpp b/src/drivers/hott/hott_telemetry/hott_telemetry.cpp index 042d9f816..d293f9954 100644 --- a/src/drivers/hott/hott_telemetry/hott_telemetry.cpp +++ b/src/drivers/hott/hott_telemetry/hott_telemetry.cpp @@ -237,7 +237,7 @@ hott_telemetry_main(int argc, char *argv[]) thread_should_exit = false; deamon_task = task_spawn_cmd(daemon_name, SCHED_DEFAULT, - SCHED_PRIORITY_MAX - 40, + SCHED_PRIORITY_DEFAULT, 2048, hott_telemetry_thread_main, (argv) ? (const char **)&argv[2] : (const char **)NULL); diff --git a/src/drivers/meas_airspeed/meas_airspeed.cpp b/src/drivers/meas_airspeed/meas_airspeed.cpp index 3cd6d6720..9251cff7b 100644 --- a/src/drivers/meas_airspeed/meas_airspeed.cpp +++ b/src/drivers/meas_airspeed/meas_airspeed.cpp @@ -77,7 +77,6 @@ #include <systemlib/err.h> #include <systemlib/param/param.h> #include <systemlib/perf_counter.h> -#include <mathlib/mathlib.h> #include <drivers/drv_airspeed.h> #include <drivers/drv_hrt.h> @@ -178,31 +177,26 @@ MEASAirspeed::collect() return ret; } - //uint16_t diff_pres_pa = (val[1]) | ((val[0] & ~(0xC0)) << 8); - uint16_t temp = (val[3] & 0xE0) << 8 | val[2]; - - // XXX leaving this in until new calculation method has been cross-checked - //diff_pres_pa = abs(diff_pres_pa - (16384 / 2.0f)); - //diff_pres_pa -= _diff_pres_offset; int16_t dp_raw = 0, dT_raw = 0; dp_raw = (val[0] << 8) + val[1]; - dp_raw = 0x3FFF & dp_raw; //mask the used bits + /* mask the used bits */ + dp_raw = 0x3FFF & dp_raw; dT_raw = (val[2] << 8) + val[3]; dT_raw = (0xFFE0 & dT_raw) >> 5; float temperature = ((200 * dT_raw) / 2047) - 50; - // XXX we may want to smooth out the readings to remove noise. - - // Calculate differential pressure. As its centered around 8000 - // and can go positive or negative, enforce absolute value -// uint16_t diff_press_pa = abs(dp_raw - (16384 / 2.0f)); + /* calculate differential pressure. As its centered around 8000 + * and can go positive or negative, enforce absolute value + */ const float P_min = -1.0f; const float P_max = 1.0f; - float diff_press_pa = math::max(0.0f, fabsf( ( ((float)dp_raw - 0.1f*16383.0f) * (P_max-P_min)/(0.8f*16383.0f) + P_min) * 6894.8f) - _diff_pres_offset); + float diff_press_pa = fabsf( ( ((float)dp_raw - 0.1f*16383.0f) * (P_max-P_min)/(0.8f*16383.0f) + P_min) * 6894.8f) - _diff_pres_offset; + if (diff_press_pa < 0.0f) + diff_press_pa = 0.0f; struct differential_pressure_s report; - // Track maximum differential pressure measured (so we can work out top speed). + /* track maximum differential pressure measured (so we can work out top speed). */ if (diff_press_pa > _max_differential_pressure_pa) { _max_differential_pressure_pa = diff_press_pa; } @@ -390,7 +384,7 @@ test() err(1, "immediate read failed"); warnx("single read"); - warnx("diff pressure: %d pa", report.differential_pressure_pa); + warnx("diff pressure: %d pa", (double)report.differential_pressure_pa); /* start the sensor polling at 2Hz */ if (OK != ioctl(fd, SENSORIOCSPOLLRATE, 2)) diff --git a/src/drivers/ms5611/ms5611.cpp b/src/drivers/ms5611/ms5611.cpp index 87788824a..6326cf7fc 100644 --- a/src/drivers/ms5611/ms5611.cpp +++ b/src/drivers/ms5611/ms5611.cpp @@ -124,6 +124,8 @@ protected: int32_t _TEMP; int64_t _OFF; int64_t _SENS; + float _P; + float _T; /* altitude conversion calibration */ unsigned _msl_pressure; /* in kPa */ @@ -623,6 +625,8 @@ MS5611::collect() /* pressure calculation, result in Pa */ int32_t P = (((raw * _SENS) >> 21) - _OFF) >> 15; + _P = P * 0.01f; + _T = _TEMP * 0.01f; /* generate a new report */ report.temperature = _TEMP / 100.0f; @@ -695,6 +699,8 @@ MS5611::print_info() printf("TEMP: %d\n", _TEMP); printf("SENS: %lld\n", _SENS); printf("OFF: %lld\n", _OFF); + printf("P: %.3f\n", _P); + printf("T: %.3f\n", _T); printf("MSL pressure: %10.4f\n", (double)(_msl_pressure / 100.f)); printf("factory_setup %u\n", _prom.factory_setup); diff --git a/src/drivers/px4fmu/fmu.cpp b/src/drivers/px4fmu/fmu.cpp index b878d29bc..c067d363b 100644 --- a/src/drivers/px4fmu/fmu.cpp +++ b/src/drivers/px4fmu/fmu.cpp @@ -65,6 +65,7 @@ #include <systemlib/err.h> #include <systemlib/mixer/mixer.h> #include <systemlib/pwm_limit/pwm_limit.h> +#include <systemlib/board_serial.h> #include <drivers/drv_mixer.h> #include <drivers/drv_rc_input.h> @@ -224,10 +225,10 @@ PX4FMU::PX4FMU() : _armed(false), _pwm_on(false), _mixers(nullptr), - _failsafe_pwm( {0}), - _disarmed_pwm( {0}), - _num_failsafe_set(0), - _num_disarmed_set(0) + _failsafe_pwm({0}), + _disarmed_pwm({0}), + _num_failsafe_set(0), + _num_disarmed_set(0) { for (unsigned i = 0; i < _max_actuators; i++) { _min_pwm[i] = PWM_DEFAULT_MIN; @@ -575,7 +576,7 @@ PX4FMU::task_main() if (i >= outputs.noutputs || !isfinite(outputs.output[i]) || outputs.output[i] < -1.0f || - outputs.output[i] > 1.0f) { + outputs.output[i] > 1.0f) { /* * Value is NaN, INF or out of band - set to the minimum value. * This will be clearly visible on the servo status and will limit the risk of accidentally @@ -933,7 +934,7 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; } - /* FALLTHROUGH */ + /* FALLTHROUGH */ case PWM_SERVO_SET(3): case PWM_SERVO_SET(2): if (_mode < MODE_4PWM) { @@ -941,7 +942,7 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; } - /* FALLTHROUGH */ + /* FALLTHROUGH */ case PWM_SERVO_SET(1): case PWM_SERVO_SET(0): if (arg <= 2100) { @@ -960,7 +961,7 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; } - /* FALLTHROUGH */ + /* FALLTHROUGH */ case PWM_SERVO_GET(3): case PWM_SERVO_GET(2): if (_mode < MODE_4PWM) { @@ -968,7 +969,7 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; } - /* FALLTHROUGH */ + /* FALLTHROUGH */ case PWM_SERVO_GET(1): case PWM_SERVO_GET(0): *(servo_position_t *)arg = up_pwm_servo_get(cmd - PWM_SERVO_GET(0)); @@ -1005,6 +1006,40 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg) break; + case PWM_SERVO_SET_COUNT: { + /* change the number of outputs that are enabled for + * PWM. This is used to change the split between GPIO + * and PWM under control of the flight config + * parameters. Note that this does not allow for + * changing a set of pins to be used for serial on + * FMUv1 + */ + switch (arg) { + case 0: + set_mode(MODE_NONE); + break; + + case 2: + set_mode(MODE_2PWM); + break; + + case 4: + set_mode(MODE_4PWM); + break; + +#if defined(CONFIG_ARCH_BOARD_PX4FMU_V2) + case 6: + set_mode(MODE_6PWM); + break; +#endif + + default: + ret = -EINVAL; + break; + } + break; + } + case MIXERIOCRESET: if (_mixers != nullptr) { delete _mixers; @@ -1107,10 +1142,12 @@ PX4FMU::sensor_reset(int ms) stm32_configgpio(GPIO_SPI_CS_GYRO_OFF); stm32_configgpio(GPIO_SPI_CS_ACCEL_MAG_OFF); stm32_configgpio(GPIO_SPI_CS_BARO_OFF); + stm32_configgpio(GPIO_SPI_CS_MPU_OFF); stm32_gpiowrite(GPIO_SPI_CS_GYRO_OFF, 0); stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG_OFF, 0); stm32_gpiowrite(GPIO_SPI_CS_BARO_OFF, 0); + stm32_gpiowrite(GPIO_SPI_CS_MPU_OFF, 0); stm32_configgpio(GPIO_SPI1_SCK_OFF); stm32_configgpio(GPIO_SPI1_MISO_OFF); @@ -1123,10 +1160,12 @@ PX4FMU::sensor_reset(int ms) stm32_configgpio(GPIO_GYRO_DRDY_OFF); stm32_configgpio(GPIO_MAG_DRDY_OFF); stm32_configgpio(GPIO_ACCEL_DRDY_OFF); + stm32_configgpio(GPIO_EXTI_MPU_DRDY_OFF); stm32_gpiowrite(GPIO_GYRO_DRDY_OFF, 0); stm32_gpiowrite(GPIO_MAG_DRDY_OFF, 0); stm32_gpiowrite(GPIO_ACCEL_DRDY_OFF, 0); + stm32_gpiowrite(GPIO_EXTI_MPU_DRDY_OFF, 0); /* set the sensor rail off */ stm32_configgpio(GPIO_VDD_3V3_SENSORS_EN); @@ -1159,6 +1198,13 @@ PX4FMU::sensor_reset(int ms) stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, 1); stm32_gpiowrite(GPIO_SPI_CS_BARO, 1); stm32_gpiowrite(GPIO_SPI_CS_MPU, 1); + + // // XXX bring up the EXTI pins again + // stm32_configgpio(GPIO_GYRO_DRDY); + // stm32_configgpio(GPIO_MAG_DRDY); + // stm32_configgpio(GPIO_ACCEL_DRDY); + // stm32_configgpio(GPIO_EXTI_MPU_DRDY); + #endif #endif } @@ -1431,7 +1477,6 @@ void sensor_reset(int ms) { int fd; - int ret; fd = open(PX4FMU_DEVICE_PATH, O_RDWR); @@ -1591,6 +1636,15 @@ fmu_main(int argc, char *argv[]) errx(0, "FMU driver stopped"); } + if (!strcmp(verb, "id")) { + char id[12]; + (void)get_board_serial(id); + + errx(0, "Board serial:\n %02X%02X%02X%02X %02X%02X%02X%02X %02X%02X%02X%02X", + (unsigned)id[0], (unsigned)id[1], (unsigned)id[2], (unsigned)id[3], (unsigned)id[4], (unsigned)id[5], + (unsigned)id[6], (unsigned)id[7], (unsigned)id[8], (unsigned)id[9], (unsigned)id[10], (unsigned)id[11]); + } + if (fmu_start() != OK) errx(1, "failed to start the FMU driver"); @@ -1647,6 +1701,7 @@ fmu_main(int argc, char *argv[]) sensor_reset(0); warnx("resettet default time"); } + exit(0); } diff --git a/src/drivers/px4fmu/module.mk b/src/drivers/px4fmu/module.mk index d918abd57..05bc7a5b3 100644 --- a/src/drivers/px4fmu/module.mk +++ b/src/drivers/px4fmu/module.mk @@ -3,5 +3,4 @@ # MODULE_COMMAND = fmu -SRCS = fmu.cpp \ - ../../modules/systemlib/pwm_limit/pwm_limit.c +SRCS = fmu.cpp diff --git a/src/drivers/px4io/px4io.cpp b/src/drivers/px4io/px4io.cpp index cbdd5acc4..df847a64d 100644 --- a/src/drivers/px4io/px4io.cpp +++ b/src/drivers/px4io/px4io.cpp @@ -1,6 +1,6 @@ /**************************************************************************** * - * Copyright (c) 2012, 2013 PX4 Development Team. All rights reserved. + * Copyright (c) 2012-2014 PX4 Development Team. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions @@ -35,7 +35,7 @@ * @file px4io.cpp * Driver for the PX4IO board. * - * PX4IO is connected via I2C. + * PX4IO is connected via I2C or DMA enabled high-speed UART. */ #include <nuttx/config.h> @@ -270,7 +270,8 @@ private: orb_advert_t _to_servorail; ///< servorail status orb_advert_t _to_safety; ///< status of safety - actuator_outputs_s _outputs; ///<mixed outputs + actuator_outputs_s _outputs; ///< mixed outputs + servorail_status_s _servorail_status; ///< servorail status bool _primary_pwm_device; ///< true if we are the default PWM output @@ -450,7 +451,7 @@ private: namespace { -PX4IO *g_dev; +PX4IO *g_dev = nullptr; } @@ -504,7 +505,8 @@ PX4IO::PX4IO(device::Device *interface) : /* open MAVLink text channel */ _mavlink_fd = ::open(MAVLINK_LOG_DEVICE, 0); - _debug_enabled = true; + _debug_enabled = false; + _servorail_status.rssi_v = 0; } PX4IO::~PX4IO() @@ -578,6 +580,12 @@ PX4IO::init() /* get some parameters */ unsigned protocol = io_reg_get(PX4IO_PAGE_CONFIG, PX4IO_P_CONFIG_PROTOCOL_VERSION); + if (protocol == _io_reg_get_error) { + log("failed to communicate with IO"); + mavlink_log_emergency(_mavlink_fd, "[IO] failed to communicate with IO, abort."); + return -1; + } + if (protocol != PX4IO_PROTOCOL_VERSION) { log("protocol/firmware mismatch"); mavlink_log_emergency(_mavlink_fd, "[IO] protocol/firmware mismatch, abort."); @@ -772,8 +780,6 @@ PX4IO::task_main() hrt_abstime poll_last = 0; hrt_abstime orb_check_last = 0; - log("starting"); - _thread_mavlink_fd = ::open(MAVLINK_LOG_DEVICE, 0); /* @@ -807,8 +813,6 @@ PX4IO::task_main() fds[0].fd = _t_actuator_controls_0; fds[0].events = POLLIN; - log("ready"); - /* lock against the ioctl handler */ lock(); @@ -1300,6 +1304,7 @@ PX4IO::io_handle_battery(uint16_t vbatt, uint16_t ibatt) /* voltage is scaled to mV */ battery_status.voltage_v = vbatt / 1000.0f; + battery_status.voltage_filtered_v = vbatt / 1000.0f; /* ibatt contains the raw ADC count, as 12 bit ADC @@ -1331,19 +1336,18 @@ PX4IO::io_handle_battery(uint16_t vbatt, uint16_t ibatt) void PX4IO::io_handle_vservo(uint16_t vservo, uint16_t vrssi) { - servorail_status_s servorail_status; - servorail_status.timestamp = hrt_absolute_time(); + _servorail_status.timestamp = hrt_absolute_time(); /* voltage is scaled to mV */ - servorail_status.voltage_v = vservo * 0.001f; - servorail_status.rssi_v = vrssi * 0.001f; + _servorail_status.voltage_v = vservo * 0.001f; + _servorail_status.rssi_v = vrssi * 0.001f; /* lazily publish the servorail voltages */ if (_to_servorail > 0) { - orb_publish(ORB_ID(servorail_status), _to_servorail, &servorail_status); + orb_publish(ORB_ID(servorail_status), _to_servorail, &_servorail_status); } else { - _to_servorail = orb_advertise(ORB_ID(servorail_status), &servorail_status); + _to_servorail = orb_advertise(ORB_ID(servorail_status), &_servorail_status); } } @@ -1450,6 +1454,13 @@ PX4IO::io_publish_raw_rc() rc_val.input_source = RC_INPUT_SOURCE_UNKNOWN; } + /* set RSSI */ + + if (rc_val.input_source != RC_INPUT_SOURCE_PX4IO_SBUS) { + // XXX the correct scaling needs to be validated here + rc_val.rssi = (_servorail_status.rssi_v / 3.3f) * UINT8_MAX; + } + /* lazily advertise on first publication */ if (_to_input_rc == 0) { _to_input_rc = orb_advertise(ORB_ID(input_rc), &rc_val); @@ -1664,7 +1675,18 @@ PX4IO::mixer_send(const char *buf, unsigned buflen, unsigned retries) total_len++; } - int ret = io_reg_set(PX4IO_PAGE_MIXERLOAD, 0, (uint16_t *)frame, total_len / 2); + int ret; + + for (int i = 0; i < 30; i++) { + /* failed, but give it a 2nd shot */ + ret = io_reg_set(PX4IO_PAGE_MIXERLOAD, 0, (uint16_t *)frame, total_len / 2); + + if (ret) { + usleep(333); + } else { + break; + } + } /* print mixer chunk */ if (debuglevel > 5 || ret) { @@ -1688,7 +1710,21 @@ PX4IO::mixer_send(const char *buf, unsigned buflen, unsigned retries) msg->text[0] = '\n'; msg->text[1] = '\0'; - int ret = io_reg_set(PX4IO_PAGE_MIXERLOAD, 0, (uint16_t *)frame, (sizeof(px4io_mixdata) + 2) / 2); + int ret; + + for (int i = 0; i < 30; i++) { + /* failed, but give it a 2nd shot */ + ret = io_reg_set(PX4IO_PAGE_MIXERLOAD, 0, (uint16_t *)frame, (sizeof(px4io_mixdata) + 2) / 2); + + if (ret) { + usleep(333); + } else { + break; + } + } + + if (ret) + return ret; retries--; @@ -1798,7 +1834,7 @@ PX4IO::print_status() printf("\n"); - if (raw_inputs > 0) { + if ((flags & PX4IO_P_STATUS_FLAGS_RC_PPM)) { int frame_len = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_RC_DATA); printf("RC data (PPM frame len) %u us\n", frame_len); @@ -2355,8 +2391,10 @@ start(int argc, char *argv[]) /* create the driver - it will set g_dev */ (void)new PX4IO(interface); - if (g_dev == nullptr) + if (g_dev == nullptr) { + delete interface; errx(1, "driver alloc failed"); + } if (OK != g_dev->init()) { delete g_dev; @@ -2420,6 +2458,69 @@ detect(int argc, char *argv[]) } void +checkcrc(int argc, char *argv[]) +{ + bool keep_running = false; + + if (g_dev == nullptr) { + /* allocate the interface */ + device::Device *interface = get_interface(); + + /* create the driver - it will set g_dev */ + (void)new PX4IO(interface); + + if (g_dev == nullptr) + errx(1, "driver alloc failed"); + } else { + /* its already running, don't kill the driver */ + keep_running = true; + } + + /* + check IO CRC against CRC of a file + */ + if (argc < 2) { + printf("usage: px4io checkcrc filename\n"); + exit(1); + } + int fd = open(argv[1], O_RDONLY); + if (fd == -1) { + printf("open of %s failed - %d\n", argv[1], errno); + exit(1); + } + const uint32_t app_size_max = 0xf000; + uint32_t fw_crc = 0; + uint32_t nbytes = 0; + while (true) { + uint8_t buf[16]; + int n = read(fd, buf, sizeof(buf)); + if (n <= 0) break; + fw_crc = crc32part(buf, n, fw_crc); + nbytes += n; + } + close(fd); + while (nbytes < app_size_max) { + uint8_t b = 0xff; + fw_crc = crc32part(&b, 1, fw_crc); + nbytes++; + } + + int ret = g_dev->ioctl(nullptr, PX4IO_CHECK_CRC, fw_crc); + + if (!keep_running) { + delete g_dev; + g_dev = nullptr; + } + + if (ret != OK) { + printf("check CRC failed - %d\n", ret); + exit(1); + } + printf("CRCs match\n"); + exit(0); +} + +void bind(int argc, char *argv[]) { int pulses; @@ -2569,17 +2670,17 @@ monitor(void) read(0, &c, 1); if (cancels-- == 0) { - printf("\033[H"); /* move cursor home and clear screen */ + printf("\033[2J\033[H"); /* move cursor home and clear screen */ exit(0); } } if (g_dev != nullptr) { - printf("\033[H"); /* move cursor home and clear screen */ + printf("\033[2J\033[H"); /* move cursor home and clear screen */ (void)g_dev->print_status(); (void)g_dev->print_debug(); - printf("[ Use 'px4io debug <N>' for more output. Hit <enter> three times to exit monitor mode ]\n"); + printf("\n\n\n[ Use 'px4io debug <N>' for more output. Hit <enter> three times to exit monitor mode ]\n"); } else { errx(1, "driver not loaded, exiting"); @@ -2613,12 +2714,16 @@ px4io_main(int argc, char *argv[]) if (!strcmp(argv[1], "detect")) detect(argc - 1, argv + 1); + if (!strcmp(argv[1], "checkcrc")) + checkcrc(argc - 1, argv + 1); + if (!strcmp(argv[1], "update")) { if (g_dev != nullptr) { printf("[px4io] loaded, detaching first\n"); /* stop the driver */ delete g_dev; + g_dev = nullptr; } PX4IO_Uploader *up; @@ -2691,18 +2796,30 @@ px4io_main(int argc, char *argv[]) } if (g_dev == nullptr) { warnx("px4io is not started, still attempting upgrade"); - } else { - uint16_t arg = atol(argv[2]); - int ret = g_dev->ioctl(nullptr, PX4IO_REBOOT_BOOTLOADER, arg); - if (ret != OK) { - printf("reboot failed - %d\n", ret); - exit(1); + + /* allocate the interface */ + device::Device *interface = get_interface(); + + /* create the driver - it will set g_dev */ + (void)new PX4IO(interface); + + if (g_dev == nullptr) { + delete interface; + errx(1, "driver alloc failed"); } + } - // tear down the px4io instance - delete g_dev; + uint16_t arg = atol(argv[2]); + int ret = g_dev->ioctl(nullptr, PX4IO_REBOOT_BOOTLOADER, arg); + if (ret != OK) { + printf("reboot failed - %d\n", ret); + exit(1); } + // tear down the px4io instance + delete g_dev; + g_dev = nullptr; + // upload the specified firmware const char *fn[2]; fn[0] = argv[3]; @@ -2760,6 +2877,7 @@ px4io_main(int argc, char *argv[]) /* stop the driver */ delete g_dev; + g_dev = nullptr; exit(0); } @@ -2798,49 +2916,6 @@ px4io_main(int argc, char *argv[]) exit(0); } - if (!strcmp(argv[1], "checkcrc")) { - /* - check IO CRC against CRC of a file - */ - if (argc <= 2) { - printf("usage: px4io checkcrc filename\n"); - exit(1); - } - if (g_dev == nullptr) { - printf("px4io is not started\n"); - exit(1); - } - int fd = open(argv[2], O_RDONLY); - if (fd == -1) { - printf("open of %s failed - %d\n", argv[2], errno); - exit(1); - } - const uint32_t app_size_max = 0xf000; - uint32_t fw_crc = 0; - uint32_t nbytes = 0; - while (true) { - uint8_t buf[16]; - int n = read(fd, buf, sizeof(buf)); - if (n <= 0) break; - fw_crc = crc32part(buf, n, fw_crc); - nbytes += n; - } - close(fd); - while (nbytes < app_size_max) { - uint8_t b = 0xff; - fw_crc = crc32part(&b, 1, fw_crc); - nbytes++; - } - - int ret = g_dev->ioctl(nullptr, PX4IO_CHECK_CRC, fw_crc); - if (ret != OK) { - printf("check CRC failed - %d\n", ret); - exit(1); - } - printf("CRCs match\n"); - exit(0); - } - if (!strcmp(argv[1], "rx_dsm") || !strcmp(argv[1], "rx_dsm_10bit") || !strcmp(argv[1], "rx_dsm_11bit") || diff --git a/src/drivers/px4io/px4io_uploader.cpp b/src/drivers/px4io/px4io_uploader.cpp index 41f93a8ee..dd8abbac5 100644 --- a/src/drivers/px4io/px4io_uploader.cpp +++ b/src/drivers/px4io/px4io_uploader.cpp @@ -51,6 +51,7 @@ #include <poll.h> #include <termios.h> #include <sys/stat.h> +#include <nuttx/arch.h> #include <crc32.h> @@ -120,8 +121,15 @@ PX4IO_Uploader::upload(const char *filenames[]) cfsetspeed(&t, 115200); tcsetattr(_io_fd, TCSANOW, &t); - /* look for the bootloader */ - ret = sync(); + /* look for the bootloader for 150 ms */ + for (int i = 0; i < 15; i++) { + ret = sync(); + if (ret == OK) { + break; + } else { + usleep(10000); + } + } if (ret != OK) { /* this is immediately fatal */ @@ -226,6 +234,11 @@ PX4IO_Uploader::upload(const char *filenames[]) close(_fw_fd); close(_io_fd); _io_fd = -1; + + // sleep for enough time for the IO chip to boot. This makes + // forceupdate more reliably startup IO again after update + up_udelay(100*1000); + return ret; } diff --git a/src/drivers/px4io/uploader.h b/src/drivers/px4io/uploader.h index 22387a3e2..55f63eef9 100644 --- a/src/drivers/px4io/uploader.h +++ b/src/drivers/px4io/uploader.h @@ -91,7 +91,7 @@ private: void drain(); int send(uint8_t c); int send(uint8_t *p, unsigned count); - int get_sync(unsigned timeout = 1000); + int get_sync(unsigned timeout = 40); int sync(); int get_info(int param, uint32_t &val); int erase(); diff --git a/src/drivers/rgbled/rgbled.cpp b/src/drivers/rgbled/rgbled.cpp index 727c86e02..4f58891ed 100644 --- a/src/drivers/rgbled/rgbled.cpp +++ b/src/drivers/rgbled/rgbled.cpp @@ -559,7 +559,7 @@ RGBLED::get(bool &on, bool &powersave, uint8_t &r, uint8_t &g, uint8_t &b) void rgbled_usage() { - warnx("missing command: try 'start', 'test', 'info', 'off', 'rgb 30 40 50'"); + warnx("missing command: try 'start', 'test', 'info', 'off', 'stop', 'rgb 30 40 50'"); warnx("options:"); warnx(" -b i2cbus (%d)", PX4_I2C_BUS_LED); warnx(" -a addr (0x%x)", ADDR); @@ -643,7 +643,7 @@ rgbled_main(int argc, char *argv[]) if (g_rgbled == nullptr) { warnx("not started"); rgbled_usage(); - exit(0); + exit(1); } if (!strcmp(verb, "test")) { @@ -669,7 +669,7 @@ rgbled_main(int argc, char *argv[]) exit(0); } - if (!strcmp(verb, "off")) { + if (!strcmp(verb, "off") || !strcmp(verb, "stop")) { fd = open(RGBLED_DEVICE_PATH, 0); if (fd == -1) { @@ -681,6 +681,12 @@ rgbled_main(int argc, char *argv[]) exit(ret); } + if (!strcmp(verb, "stop")) { + delete g_rgbled; + g_rgbled = nullptr; + exit(0); + } + if (!strcmp(verb, "rgb")) { if (argc < 5) { errx(1, "Usage: rgbled rgb <red> <green> <blue>"); |