diff options
Diffstat (limited to 'src/modules/px4iofirmware/protocol.h')
| -rw-r--r-- | src/modules/px4iofirmware/protocol.h | 21 |
1 files changed, 15 insertions, 6 deletions
diff --git a/src/modules/px4iofirmware/protocol.h b/src/modules/px4iofirmware/protocol.h index 6c20d6006..050783687 100644 --- a/src/modules/px4iofirmware/protocol.h +++ b/src/modules/px4iofirmware/protocol.h @@ -142,6 +142,7 @@ #define PX4IO_P_RAW_RC_FLAGS_FAILSAFE (1 << 1) /* receiver is in failsafe mode */ #define PX4IO_P_RAW_RC_FLAGS_RC_DSM11 (1 << 2) /* DSM decoding is 11 bit mode */ #define PX4IO_P_RAW_RC_FLAGS_MAPPING_OK (1 << 3) /* Channel mapping is ok */ +#define PX4IO_P_RAW_RC_FLAGS_RC_OK (1 << 4) /* RC reception ok */ #define PX4IO_P_RAW_RC_NRSSI 2 /* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */ #define PX4IO_P_RAW_RC_DATA 3 /* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */ @@ -178,6 +179,7 @@ #define PX4IO_P_SETUP_ARMING_ALWAYS_PWM_ENABLE (1 << 5) /* Output of PWM right after startup enabled to help ESCs initialize and prevent them from beeping */ #define PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED (1 << 6) /* Disable the IO-internal evaluation of the RC */ #define PX4IO_P_SETUP_ARMING_LOCKDOWN (1 << 7) /* If set, the system operates normally, but won't actuate any servos */ +#define PX4IO_P_SETUP_ARMING_FORCE_FAILSAFE (1 << 8) /* If set, the system will always output the failsafe values */ #define PX4IO_P_SETUP_PWM_RATES 2 /* bitmask, 0 = low rate, 1 = high rate */ #define PX4IO_P_SETUP_PWM_DEFAULTRATE 3 /* 'low' PWM frame output rate in Hz */ @@ -189,6 +191,8 @@ #define PX4IO_P_SETUP_RELAYS_POWER2 (1<<1) /* hardware rev [1] power relay 2 */ #define PX4IO_P_SETUP_RELAYS_ACC1 (1<<2) /* hardware rev [1] accessory power 1 */ #define PX4IO_P_SETUP_RELAYS_ACC2 (1<<3) /* hardware rev [1] accessory power 2 */ +#else +#define PX4IO_P_SETUP_RELAYS_PAD 5 #endif #define PX4IO_P_SETUP_VBATT_SCALE 6 /* hardware rev [1] battery voltage correction factor (float) */ @@ -208,15 +212,16 @@ enum { /* DSM bind states */ #define PX4IO_REBOOT_BL_MAGIC 14662 /* required argument for reboot (random) */ #define PX4IO_P_SETUP_CRC 11 /* get CRC of IO firmware */ - /* 12 occupied by CRC */ + /* storage space of 12 occupied by CRC */ +#define PX4IO_P_SETUP_FORCE_SAFETY_OFF 12 /* force safety switch into + 'armed' (PWM enabled) state - this is a non-data write and + hence index 12 can safely be used. */ #define PX4IO_P_SETUP_RC_THR_FAILSAFE_US 13 /**< the throttle failsafe pulse length in microseconds */ -#define PX4IO_P_SETUP_FORCE_SAFETY_OFF 12 /* force safety switch into - 'armed' (PWM enabled) state */ -#define PX4IO_FORCE_SAFETY_MAGIC 22027 /* required argument for force safety (random) */ +#define PX4IO_FORCE_SAFETY_MAGIC 22027 /* required argument for force safety (random) */ /* autopilot control values, -10000..10000 */ -#define PX4IO_PAGE_CONTROLS 51 /**< actuator control groups, one after the other, 8 wide */ +#define PX4IO_PAGE_CONTROLS 51 /**< actuator control groups, one after the other, 8 wide */ #define PX4IO_P_CONTROLS_GROUP_0 (PX4IO_PROTOCOL_MAX_CONTROL_COUNT * 0) /**< 0..PX4IO_PROTOCOL_MAX_CONTROL_COUNT - 1 */ #define PX4IO_P_CONTROLS_GROUP_1 (PX4IO_PROTOCOL_MAX_CONTROL_COUNT * 1) /**< 0..PX4IO_PROTOCOL_MAX_CONTROL_COUNT - 1 */ #define PX4IO_P_CONTROLS_GROUP_2 (PX4IO_PROTOCOL_MAX_CONTROL_COUNT * 2) /**< 0..PX4IO_PROTOCOL_MAX_CONTROL_COUNT - 1 */ @@ -249,6 +254,10 @@ enum { /* DSM bind states */ /* PWM failsafe values - zero disables the output */ #define PX4IO_PAGE_FAILSAFE_PWM 55 /**< 0..CONFIG_ACTUATOR_COUNT-1 */ +/* PWM failsafe values - zero disables the output */ +#define PX4IO_PAGE_SENSORS 56 /**< Sensors connected to PX4IO */ +#define PX4IO_P_SENSORS_ALTITUDE 0 /**< Altitude of an external sensor (HoTT or S.BUS2) */ + /* Debug and test page - not used in normal operation */ #define PX4IO_PAGE_TEST 127 #define PX4IO_P_TEST_LED 0 /**< set the amber LED on/off */ @@ -308,7 +317,7 @@ struct IOPacket { #define PKT_COUNT(_p) ((_p).count_code & PKT_COUNT_MASK) #define PKT_CODE(_p) ((_p).count_code & PKT_CODE_MASK) -#define PKT_SIZE(_p) ((uint8_t *)&((_p).regs[PKT_COUNT(_p)]) - ((uint8_t *)&(_p))) +#define PKT_SIZE(_p) ((size_t)((uint8_t *)&((_p).regs[PKT_COUNT(_p)]) - ((uint8_t *)&(_p)))) static const uint8_t crc8_tab[256] __attribute__((unused)) = { |