diff options
Diffstat (limited to 'src/modules/px4iofirmware/protocol.h')
-rw-r--r-- | src/modules/px4iofirmware/protocol.h | 20 |
1 files changed, 16 insertions, 4 deletions
diff --git a/src/modules/px4iofirmware/protocol.h b/src/modules/px4iofirmware/protocol.h index e5bef6eb3..d48c6c529 100644 --- a/src/modules/px4iofirmware/protocol.h +++ b/src/modules/px4iofirmware/protocol.h @@ -111,7 +111,6 @@ #define PX4IO_P_STATUS_FLAGS_INIT_OK (1 << 10) /* initialisation of the IO completed without error */ #define PX4IO_P_STATUS_FLAGS_FAILSAFE (1 << 11) /* failsafe is active */ #define PX4IO_P_STATUS_FLAGS_SAFETY_OFF (1 << 12) /* safety is off */ -#define PX4IO_P_STATUS_FLAGS_RC_DSM11 (1 << 13) /* DSM input is 11 bit data */ #define PX4IO_P_STATUS_ALARMS 3 /* alarm flags - alarms latch, write 1 to a bit to clear it */ #define PX4IO_P_STATUS_ALARMS_VBATT_LOW (1 << 0) /* [1] VBatt is very close to regulator dropout */ @@ -128,8 +127,6 @@ #define PX4IO_P_STATUS_VSERVO 6 /* [2] servo rail voltage in mV */ #define PX4IO_P_STATUS_VRSSI 7 /* [2] RSSI voltage */ #define PX4IO_P_STATUS_PRSSI 8 /* [2] RSSI PWM value */ -#define PX4IO_P_STATUS_NRSSI 9 /* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */ -#define PX4IO_P_STATUS_RC_DATA 10 /* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */ /* array of post-mix actuator outputs, -10000..10000 */ #define PX4IO_PAGE_ACTUATORS 2 /* 0..CONFIG_ACTUATOR_COUNT-1 */ @@ -140,7 +137,17 @@ /* array of raw RC input values, microseconds */ #define PX4IO_PAGE_RAW_RC_INPUT 4 #define PX4IO_P_RAW_RC_COUNT 0 /* number of valid channels */ -#define PX4IO_P_RAW_RC_BASE 1 /* CONFIG_RC_INPUT_COUNT channels from here */ +#define PX4IO_P_RAW_RC_FLAGS 1 /* RC detail status flags */ +#define PX4IO_P_RAW_RC_FLAGS_FRAME_DROP (1 << 0) /* single frame drop */ +#define PX4IO_P_RAW_RC_FLAGS_FAILSAFE (1 << 1) /* receiver is in failsafe mode */ +#define PX4IO_P_RAW_RC_FLAGS_RC_DSM11 (1 << 2) /* DSM decoding is 11 bit mode */ +#define PX4IO_P_RAW_RC_FLAGS_MAPPING_OK (1 << 3) /* Channel mapping is ok */ + +#define PX4IO_P_RAW_RC_NRSSI 2 /* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */ +#define PX4IO_P_RAW_RC_DATA 3 /* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */ +#define PX4IO_P_RAW_FRAME_COUNT 4 /* Number of total received frames (wrapping counter) */ +#define PX4IO_P_RAW_LOST_FRAME_COUNT 5 /* Number of total dropped frames (wrapping counter) */ +#define PX4IO_P_RAW_RC_BASE 6 /* CONFIG_RC_INPUT_COUNT channels from here */ /* array of scaled RC input values, -10000..10000 */ #define PX4IO_PAGE_RC_INPUT 5 @@ -157,6 +164,10 @@ /* setup page */ #define PX4IO_PAGE_SETUP 50 #define PX4IO_P_SETUP_FEATURES 0 +#define PX4IO_P_SETUP_FEATURES_SBUS1_OUT (1 << 0) /* enable S.Bus v1 output */ +#define PX4IO_P_SETUP_FEATURES_SBUS2_OUT (1 << 1) /* enable S.Bus v2 output */ +#define PX4IO_P_SETUP_FEATURES_PWM_RSSI (1 << 2) /* enable PWM RSSI parsing */ +#define PX4IO_P_SETUP_FEATURES_ADC_RSSI (1 << 3) /* enable ADC RSSI parsing */ #define PX4IO_P_SETUP_ARMING 1 /* arming controls */ #define PX4IO_P_SETUP_ARMING_IO_ARM_OK (1 << 0) /* OK to arm the IO side */ @@ -166,6 +177,7 @@ #define PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK (1 << 4) /* OK to try in-air restart */ #define PX4IO_P_SETUP_ARMING_ALWAYS_PWM_ENABLE (1 << 5) /* Output of PWM right after startup enabled to help ESCs initialize and prevent them from beeping */ #define PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED (1 << 6) /* Disable the IO-internal evaluation of the RC */ +#define PX4IO_P_SETUP_ARMING_LOCKDOWN (1 << 7) /* If set, the system operates normally, but won't actuate any servos */ #define PX4IO_P_SETUP_PWM_RATES 2 /* bitmask, 0 = low rate, 1 = high rate */ #define PX4IO_P_SETUP_PWM_DEFAULTRATE 3 /* 'low' PWM frame output rate in Hz */ |