diff options
Diffstat (limited to 'src/modules/px4iofirmware/protocol.h')
| -rw-r--r-- | src/modules/px4iofirmware/protocol.h | 8 |
1 files changed, 7 insertions, 1 deletions
diff --git a/src/modules/px4iofirmware/protocol.h b/src/modules/px4iofirmware/protocol.h index 050783687..c7e9ae3eb 100644 --- a/src/modules/px4iofirmware/protocol.h +++ b/src/modules/px4iofirmware/protocol.h @@ -1,6 +1,6 @@ /**************************************************************************** * - * Copyright (c) 2012, 2013 PX4 Development Team. All rights reserved. + * Copyright (c) 2012-2014 PX4 Development Team. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions @@ -111,6 +111,8 @@ #define PX4IO_P_STATUS_FLAGS_INIT_OK (1 << 10) /* initialisation of the IO completed without error */ #define PX4IO_P_STATUS_FLAGS_FAILSAFE (1 << 11) /* failsafe is active */ #define PX4IO_P_STATUS_FLAGS_SAFETY_OFF (1 << 12) /* safety is off */ +#define PX4IO_P_STATUS_FLAGS_FMU_INITIALIZED (1 << 13) /* FMU was initialized and OK once */ +#define PX4IO_P_STATUS_FLAGS_RC_ST24 (1 << 14) /* ST24 input is valid */ #define PX4IO_P_STATUS_ALARMS 3 /* alarm flags - alarms latch, write 1 to a bit to clear it */ #define PX4IO_P_STATUS_ALARMS_VBATT_LOW (1 << 0) /* [1] VBatt is very close to regulator dropout */ @@ -180,6 +182,8 @@ #define PX4IO_P_SETUP_ARMING_RC_HANDLING_DISABLED (1 << 6) /* Disable the IO-internal evaluation of the RC */ #define PX4IO_P_SETUP_ARMING_LOCKDOWN (1 << 7) /* If set, the system operates normally, but won't actuate any servos */ #define PX4IO_P_SETUP_ARMING_FORCE_FAILSAFE (1 << 8) /* If set, the system will always output the failsafe values */ +#define PX4IO_P_SETUP_ARMING_TERMINATION_FAILSAFE (1 << 9) /* If set, the system will never return from a failsafe, but remain in failsafe once triggered. */ +#define PX4IO_P_SETUP_ARMING_OVERRIDE_IMMEDIATE (1 << 10) /* If set then on FMU failure override is immediate. Othewise it waits for the mode switch to go past the override thrshold */ #define PX4IO_P_SETUP_PWM_RATES 2 /* bitmask, 0 = low rate, 1 = high rate */ #define PX4IO_P_SETUP_PWM_DEFAULTRATE 3 /* 'low' PWM frame output rate in Hz */ @@ -218,6 +222,7 @@ enum { /* DSM bind states */ hence index 12 can safely be used. */ #define PX4IO_P_SETUP_RC_THR_FAILSAFE_US 13 /**< the throttle failsafe pulse length in microseconds */ +#define PX4IO_P_SETUP_FORCE_SAFETY_ON 14 /* force safety switch into 'disarmed' (PWM disabled state) */ #define PX4IO_FORCE_SAFETY_MAGIC 22027 /* required argument for force safety (random) */ /* autopilot control values, -10000..10000 */ @@ -243,6 +248,7 @@ enum { /* DSM bind states */ #define PX4IO_P_RC_CONFIG_MAX 2 /**< highest input value */ #define PX4IO_P_RC_CONFIG_DEADZONE 3 /**< band around center that is ignored */ #define PX4IO_P_RC_CONFIG_ASSIGNMENT 4 /**< mapped input value */ +#define PX4IO_P_RC_CONFIG_ASSIGNMENT_MODESWITCH 100 /**< magic value for mode switch */ #define PX4IO_P_RC_CONFIG_OPTIONS 5 /**< channel options bitmask */ #define PX4IO_P_RC_CONFIG_OPTIONS_ENABLED (1 << 0) #define PX4IO_P_RC_CONFIG_OPTIONS_REVERSE (1 << 1) |