diff options
Diffstat (limited to 'src/modules/sensors/sensor_params.c')
| -rw-r--r-- | src/modules/sensors/sensor_params.c | 214 |
1 files changed, 209 insertions, 5 deletions
diff --git a/src/modules/sensors/sensor_params.c b/src/modules/sensors/sensor_params.c index bc49f5c85..7ce6ef5ef 100644 --- a/src/modules/sensors/sensor_params.c +++ b/src/modules/sensors/sensor_params.c @@ -194,16 +194,25 @@ PARAM_DEFINE_FLOAT(SENS_ACC_ZSCALE, 1.0f); /** * Differential pressure sensor offset * + * The offset (zero-reading) in Pascal + * * @group Sensor Calibration */ PARAM_DEFINE_FLOAT(SENS_DPRES_OFF, 0.0f); /** - * Differential pressure sensor analog enabled + * Differential pressure sensor analog scaling + * + * Pick the appropriate scaling from the datasheet. + * this number defines the (linear) conversion from voltage + * to Pascal (pa). For the MPXV7002DP this is 1000. + * + * NOTE: If the sensor always registers zero, try switching + * the static and dynamic tubes. * * @group Sensor Calibration */ -PARAM_DEFINE_INT32(SENS_DPRES_ANA, 0); +PARAM_DEFINE_FLOAT(SENS_DPRES_ANSC, 0); /** @@ -243,6 +252,36 @@ PARAM_DEFINE_INT32(SENS_DPRES_ANA, 0); PARAM_DEFINE_INT32(SENS_BOARD_ROT, 0); /** + * Board rotation Y (Pitch) offset + * + * This parameter defines a rotational offset in degrees around the Y (Pitch) axis. It allows the user + * to fine tune the board offset in the event of misalignment. + * + * @group Sensor Calibration + */ + PARAM_DEFINE_FLOAT(SENS_BOARD_Y_OFF, 0.0f); + +/** + * Board rotation X (Roll) offset + * + * This parameter defines a rotational offset in degrees around the X (Roll) axis It allows the user + * to fine tune the board offset in the event of misalignment. + * + * @group Sensor Calibration + */ +PARAM_DEFINE_FLOAT(SENS_BOARD_X_OFF, 0.0f); + +/** + * Board rotation Z (YAW) offset + * + * This parameter defines a rotational offset in degrees around the Z (Yaw) axis. It allows the user + * to fine tune the board offset in the event of misalignment. + * + * @group Sensor Calibration + */ +PARAM_DEFINE_FLOAT(SENS_BOARD_Z_OFF, 0.0f); + +/** * External magnetometer rotation * * This parameter defines the rotation of the external magnetometer relative @@ -253,6 +292,19 @@ PARAM_DEFINE_INT32(SENS_BOARD_ROT, 0); */ PARAM_DEFINE_INT32(SENS_EXT_MAG_ROT, 0); +/** +* Set usage of external magnetometer +* +* * Set to 0 (default) to auto-detect (will try to get the external as primary) +* * Set to 1 to force the external magnetometer as primary +* * Set to 2 to force the internal magnetometer as primary +* +* @min 0 +* @max 2 +* @group Sensor Calibration +*/ +PARAM_DEFINE_INT32(SENS_EXT_MAG, 0); + /** * RC Channel 1 Minimum @@ -488,6 +540,15 @@ PARAM_DEFINE_INT32(BAT_V_SCALE_IO, 10000); * @group Battery Calibration */ PARAM_DEFINE_FLOAT(BAT_V_SCALING, 0.0082f); +#elif CONFIG_ARCH_BOARD_AEROCORE +/** + * Scaling factor for battery voltage sensor on AeroCore. + * + * For R70 = 133K, R71 = 10K --> scale = 1.8 * 143 / (4096*10) = 0.0063 + * + * @group Battery Calibration + */ +PARAM_DEFINE_FLOAT(BAT_V_SCALING, 0.0063f); #else /** * Scaling factor for battery voltage sensor on FMU v1. @@ -536,6 +597,20 @@ PARAM_DEFINE_INT32(RC_MAP_ROLL, 1); PARAM_DEFINE_INT32(RC_MAP_PITCH, 2); /** + * Failsafe channel mapping. + * + * The RC mapping index indicates which channel is used for failsafe + * If 0, whichever channel is mapped to throttle is used + * otherwise the value indicates the specific rc channel to use + * + * @min 0 + * @max 18 + * + * + */ +PARAM_DEFINE_INT32(RC_MAP_FAILSAFE, 0); //Default to throttle function + +/** * Throttle control channel mapping. * * The channel index (starting from 1 for channel 1) indicates @@ -585,13 +660,13 @@ PARAM_DEFINE_INT32(RC_MAP_MODE_SW, 0); PARAM_DEFINE_INT32(RC_MAP_RETURN_SW, 0); /** - * Assist switch channel mapping. + * Posctl switch channel mapping. * * @min 0 * @max 18 * @group Radio Calibration */ -PARAM_DEFINE_INT32(RC_MAP_ASSIST_SW, 0); +PARAM_DEFINE_INT32(RC_MAP_POSCTL_SW, 0); /** * Loiter switch channel mapping. @@ -602,7 +677,23 @@ PARAM_DEFINE_INT32(RC_MAP_ASSIST_SW, 0); */ PARAM_DEFINE_INT32(RC_MAP_LOITER_SW, 0); -//PARAM_DEFINE_INT32(RC_MAP_OFFB_SW, 0); +/** + * Acro switch channel mapping. + * + * @min 0 + * @max 18 + * @group Radio Calibration + */ +PARAM_DEFINE_INT32(RC_MAP_ACRO_SW, 0); + +/** + * Offboard switch channel mapping. + * + * @min 0 + * @max 18 + * @group Radio Calibration + */ +PARAM_DEFINE_INT32(RC_MAP_OFFB_SW, 0); /** * Flaps channel mapping. @@ -655,3 +746,116 @@ PARAM_DEFINE_INT32(RC_MAP_AUX3, 0); * @group Radio Calibration */ PARAM_DEFINE_INT32(RC_FAILS_THR, 0); + +/** + * Threshold for selecting assist mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_ASSIST_TH, 0.25f); + +/** + * Threshold for selecting auto mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_AUTO_TH, 0.75f); + +/** + * Threshold for selecting posctl mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_POSCTL_TH, 0.5f); + +/** + * Threshold for selecting return to launch mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_RETURN_TH, 0.5f); + +/** + * Threshold for selecting loiter mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_LOITER_TH, 0.5f); + +/** + * Threshold for selecting acro mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_ACRO_TH, 0.5f); + + +/** + * Threshold for selecting offboard mode + * + * min:-1 + * max:+1 + * + * 0-1 indicate where in the full channel range the threshold sits + * 0 : min + * 1 : max + * sign indicates polarity of comparison + * positive : true when channel>th + * negative : true when channel<th + * + */ +PARAM_DEFINE_FLOAT(RC_OFFB_TH, 0.5f); |