| Commit message (Collapse) | Author | Age | Files | Lines |
|\ |
|
| | |
|
| | |
|
| |
| |
| |
| | |
ensures atomic reads, makes the reads more efficient and allows for some headroom for more RC flags. The IO driver side is updated as well, however, these flags are not published yet.
|
|/
|
|
| |
up arming check
|
|\ |
|
| |
| |
| |
| | |
warn users about badly formatted PPM frames
|
|\| |
|
| |
| |
| |
| | |
still needs some work and testing
|
| | |
|
| | |
|
|/
|
|
| |
firmware. This allows to run auxiliary payload. Cleaned up defines for RC input channel counts, this needs another sweep to then finally allow up to 16 mapped channels and up to 20-24 RAW RC channels
|
| |
|
|
|
|
|
| |
- Bind control for V2
- Relays and accessory power not supported on V2 hardware
|
|\ |
|
| | |
|
| | |
|
|\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
fmuv2_bringup_new_state_machine_drton
Conflicts:
src/drivers/blinkm/blinkm.cpp
src/drivers/px4io/px4io.cpp
src/modules/commander/state_machine_helper.c
src/modules/px4iofirmware/protocol.h
src/modules/px4iofirmware/registers.c
src/modules/systemlib/systemlib.h
src/systemcmds/reboot/reboot.c
|
| |\ |
|
| | |
| | |
| | |
| | | |
not off, arming button functionality remains as is
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
src/drivers/px4io/px4io.cpp
src/modules/commander/commander.c
src/modules/commander/state_machine_helper.c
src/modules/commander/state_machine_helper.h
src/modules/px4iofirmware/mixer.cpp
src/modules/uORB/topics/actuator_controls.h
src/modules/uORB/topics/vehicle_status.h
|
| | | | |
|
| | | |
| | | |
| | | |
| | | | |
handling
|
| |/ / |
|
| | | |
|
|\ \ \
| | |/
| |/| |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
- Use distinct common symbols for px4io and px4fmu device files, and use
instead of hardcoded filenames
- Use common symbols defining px4io bits consistently between px4fmu and
px4io builds.
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The px4io bind command allows you to put a DSM satellite receiver into
bind mode. Since this feature requires that
the dsm VCC line (red wire) be cut and routed through relay one, it is
not enabled by default in order not to
affect those not using a DSM satellite receiver or wising to use relay
one for other purposes.
NOTE: Binding DSM2 satellites in 11-bit mode is not supported due to
potential bug in some DSM2 receiver streams
when in 11-bit mode. Furthermore the px4io software folds 11 bit data
down to 10 bits so there is no resolution
advantage to to 11-bit mode.
To enable the feature the RC_RL1_DSM_VCC parameter must be set to a non
zero value from the console, or using
QGroundControl:
param set RC_RL1_DSM_VCC 1
From the console you can initiate DSM bind mode with:
uorb start
param set RC_RL1_DSM_VCC 1
px4io start
px4io bind dsm2
For binding a DSMX satellite to a DSMX transmitter you would instead
use:
px4io bind dsmx
Your receiver module should start a rapid flash and you can follow the
normal binding sequence of your
transmitter.
Note: The value of parameter RC_RL1_DSM_VCC defaults to 0, so none of
this will have any effect on an unmodified
DSM receiver connection. For this feature to work, the power wire (red)
must be cut and each side connected to a
terminal on relay1 of the px4io board.
This has been tested using Spektrum as well as Hobby King 'Orange' DSM
satellite receivers.
Both px4fmu and px4io images are updated.
|
| |
| |
| |
| | |
differences in IOv2.
|
| |
| |
| |
| | |
header.
|
| | |
|
| | |
|
|\| |
|
| |
| |
| |
| | |
failsafe), does not parse commandline arguments yet
|
| | |
|
|\| |
|
| | |
|
| | |
|
| |
| |
| |
| |
| |
| | |
we don't know how to scale it as we have no info on what sensor is
attached. As we are returning a uint16_t it is better to let the FMU
sort it out or we'll just lose precision.
|
|/ |
|
|
|