blob: 6adfa30716b76d950f0bad6f627ac5715b7ece6c (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
#!nsh
echo "[init] Octorotor startup"
#
# Load default params for this platform
#
if param compare SYS_AUTOCONFIG 1
then
# Set all params here, then disable autoconfig
param set SYS_AUTOCONFIG 0
param set MC_ATTRATE_D 0.004
param set MC_ATTRATE_I 0.0
param set MC_ATTRATE_P 0.12
param set MC_ATT_D 0.0
param set MC_ATT_I 0.0
param set MC_ATT_P 7.0
param set MC_YAWPOS_D 0.0
param set MC_YAWPOS_I 0.0
param set MC_YAWPOS_P 2.0
param set MC_YAWRATE_D 0.005
param set MC_YAWRATE_I 0.2
param set MC_YAWRATE_P 0.3
param set NAV_TAKEOFF_ALT 3.0
param set MPC_TILT_MAX 0.5
param set MPC_THR_MAX 0.7
param set MPC_THR_MIN 0.3
param set MPC_XY_D 0
param set MPC_XY_P 0.5
param set MPC_XY_VEL_D 0
param set MPC_XY_VEL_I 0
param set MPC_XY_VEL_MAX 3
param set MPC_XY_VEL_P 0.2
param set MPC_Z_D 0
param set MPC_Z_P 1
param set MPC_Z_VEL_D 0
param set MPC_Z_VEL_I 0.1
param set MPC_Z_VEL_MAX 2
param set MPC_Z_VEL_P 0.20
param save
fi
#
# Force some key parameters to sane values
# MAV_TYPE list: https://pixhawk.ethz.ch/mavlink/
# 14 = octorotor
#
param set MAV_TYPE 14
set EXIT_ON_END no
#
# Start and configure PX4IO or FMU interface
#
if px4io detect
then
# Start MAVLink (depends on orb)
mavlink start
usleep 5000
sh /etc/init.d/rc.io
else
# Start MAVLink (on UART1 / ttyS0)
mavlink start -d /dev/ttyS0
usleep 5000
fmu mode_pwm
param set BAT_V_SCALING 0.004593
set EXIT_ON_END yes
fi
#
# Load mixer
#
mixer load /dev/pwm_output $MIXER
#
# Set PWM output frequency to 400 Hz
#
pwm rate -a -r 400
#
# Set disarmed, min and max PWM signals
#
pwm disarmed -c 12345678 -p 900
pwm min -c 12345678 -p 1100
pwm max -c 12345678 -p 1900
#
# Start common for all multirotors apps
#
sh /etc/init.d/rc.multirotor
if [ $EXIT_ON_END == yes ]
then
exit
fi
|
