1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
/****************************************************************************
* drivers/wireless/cc1101/ISM1_868MHzGFSK100kbps.c
*
* Copyright (C) 2011 Uros Platise. All rights reserved.
* Copyright (C) 2011 Ales Verbic. All rights reserved.
*
* Authors: Uros Platise <uros.platise@isotel.eu>
* Ales Verbic <ales.verbic@isotel.eu>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#include <nuttx/wireless/cc1101.h>
/** Settings for 868 MHz, GFSK at 100kbps
*
* ISM Region 1 (Europe) only, Band 868–870 MHz
*
* Frequency ERP Duty Cycle Bandwidth Remarks
* 868 – 868.6 MHz +14 dBm < 1% No limits
* 868.7 – 869.2 MHz +14 dBm < 0.1% No limits
* 869.3 – 869.4 MHz +10 dBm No limits < 25 kHz Appropriate access protocol required
* 869.4 – 869.65 MHz +27 dBm < 10% < 25 kHz Channels may be combined to one high speed channel
* 869.7 -870 MHz +7 dBm No limits No limits
*
* Deviation = 46.142578
* Base frequency = 867.999985
* Carrier frequency = 867.999985
* Channel number = 0
* Carrier frequency = 867.999985
* Modulated = true
* Modulation format = GFSK
* Manchester enable = false
* Sync word qualifier mode = 30/32 sync word bits detected
* Preamble count = 4
* Channel spacing = 199.813843
* Carrier frequency = 867.999985
* Data rate = 99.9069
* RX filter BW = 210.937500
* Data format = Normal mode
* Length config = Fixed packet length mode. Length configured in PKTLEN register
* CRC enable = true
* Packet length = 62
* Device address = 00
* Address config = NO Address check, no broadcast
* CRC autoflush = true
* PA ramping = false
* TX power = 0
*/
const struct c1101_rfsettings_s cc1101_rfsettings_ISM1_868MHzGFSK100kbps = {
.FSCTRL1 = 0x08, // FSCTRL1 Frequency Synthesizer Control
.FSCTRL0 = 0x00, // FSCTRL0 Frequency Synthesizer Control
.FREQ2 = 0x20, // FREQ2 Frequency Control Word, High Byte
.FREQ1 = 0x25, // FREQ1 Frequency Control Word, Middle Byte
.FREQ0 = 0xED, // FREQ0 Frequency Control Word, Low Byte
.MDMCFG4 = 0x8B, // MDMCFG4 Modem Configuration
.MDMCFG3 = 0xE5, // MDMCFG3 Modem Configuration
.MDMCFG2 = 0x13, // MDMCFG2 Modem Configuration
.MDMCFG1 = 0x22, // MDMCFG1 Modem Configuration
.MDMCFG0 = 0xE5, // MDMCFG0 Modem Configuration
.DEVIATN = 0x46, // DEVIATN Modem Deviation Setting
.FOCCFG = 0x1D, // FOCCFG Frequency Offset Compensation Configuration
.BSCFG = 0x1C, // BSCFG Bit Synchronization Configuration
.AGCCTRL2= 0xC7, // AGCCTRL2 AGC Control
.AGCCTRL1= 0x00, // AGCCTRL1 AGC Control
.AGCCTRL0= 0xB2, // AGCCTRL0 AGC Control
.FREND1 = 0xB6, // FREND1 Front End RX Configuration
.FREND0 = 0x10, // FREND0 Front End TX Configuration
.FSCAL3 = 0xEA, // FSCAL3 Frequency Synthesizer Calibration
.FSCAL2 = 0x2A, // FSCAL2 Frequency Synthesizer Calibration
.FSCAL1 = 0x00, // FSCAL1 Frequency Synthesizer Calibration
.FSCAL0 = 0x1F, // FSCAL0 Frequency Synthesizer Calibration
.CHMIN = 0, // Fix at 9th channel: 869.80 MHz +- 100 kHz RF Bandwidth
.CHMAX = 9, // single channel
.PAMAX = 8, // 0 means power OFF, 8 represents PA[7]
.PA = {0x03, 0x0F, 0x1E, 0x27, 0x67, 0x50, 0x81, 0xC2}
};
|
